s Commands
s-pmsi
s-pmsi
Syntax
s-pmsi [[group-ip group-ip][source-ip source-ip] detail]
s-pmsi [mdSrcAddr [mdGrpAddr]] [[group-ip group-ip] [source-ip source-ip] detail]
s-pmsi ext-tunnel-id ext-tunnel-id [tunnel-id tunnel-id] [[group-ip group-ip] [source-ip source-ip] detail]
s-pmsi root-addr root-addr [lsp-id lsp-id] [[group-ip group-ip] [source-ip source-ip] detail]
s-pmsi bier-root-addr ip-address [[sub-domain sub-domain] [bfr-id bfr-id] [mpls-lbl mpls-lbl] detail]
Context
[Tree] (show>router>pim s-pmsi)
Full Context
show router pim s-pmsi
Description
This command displays information about selective provider multicast service interfaces that are currently active.
Parameters
- group-ip
-
Displays group IP address information.
- source-ip
Displays source IP address information.
h
- mdSrcAddr
-
Displays source address information of the multicast sender.
- mdGrpAddr
-
Displays group address information of the multicast sender.
- ext-tunnel-id
-
Displays information about the extended tunnel address.
- tunnel-id
-
Displays information about the tunnel identifier.
- root-addr
-
Displays information about the root address.
- lsp-id
-
Displays information about the specified LSP ID.
- sub-domain
-
Displays information about the BIER sub-domain ID.
- bfr-id
-
Displays information about the BIER-ID of the router.
- mpls-lbl
-
Displays information about the specified MPLS service label.
- detail
-
Displays detailed output.
Platforms
All
Output
The following output is an example of a PIM data MDT configuration. PIM Data MDT provides PIM data MDT descriptions.
Output Example PIM Selective Provider Tunnel*B:node-6# show router 100 pim s-pmsi
===============================================================================
PIM Selective provider tunnels
===============================================================================
MD Src Address MD Grp Address MT Index Num VPN SGs
-------------------------------------------------------------------------------
239.200.200.7 239.0.89.72 24603 1
239.200.200.7 239.0.89.73 24604 1
239.200.200.7 239.0.89.74 24605 1
239.200.200.7 239.0.89.75 24606 1
239.200.200.7 239.0.89.76 24607 1
239.200.200.7 239.0.89.77 24608 1
239.200.200.7 239.0.89.78 24609 1
239.200.200.7 239.0.89.79 24610 1
239.200.200.7 239.0.89.80 24611 1
239.200.200.7 239.0.89.81 24612 1
239.200.200.7 239.0.89.82 24613 1
239.200.200.7 239.0.89.83 24614 1
239.200.200.7 239.0.89.84 24615 1
239.200.200.7 239.0.89.85 24616 1
239.200.200.7 239.0.89.86 24617 1
239.200.200.7 239.0.89.87 24618 1
...
===============================================================================
*B:node-6#
Output Example PIM Selective Provider Tunnel Detail
*B:node-6# show router 100 pim s-pmsi detail
===============================================================================
PIM Selective provider tunnels
===============================================================================
Md Source Address : 239.200.200.7 Md Group Address : 239.0.89.72
Number of VPN SGs : 1 Uptime : 0d 00:00:18
MT IfIndex : 24603 Egress Fwding Rate : 163.2 kbps
VPN Group Address : 239.1.0.0 VPN Source Address : 10.2.102.1
State : RX Joined
Expiry Timer : 0d 00:02:41
===============================================================================
PIM Selective provider tunnels
===============================================================================
Md Source Address : 239.200.200.7 Md Group Address : 239.0.89.73
Number of VPN SGs : 1 Uptime : 0d 00:00:18
MT IfIndex : 24604 Egress Fwding Rate : 163.2 kbps
VPN Group Address : 239.1.0.1 VPN Source Address : 10.2.102.1
State : RX Joined
Expiry Timer : 0d 00:02:41
===============================================================================
PIM Selective provider tunnels
===============================================================================
Md Source Address : 239.200.200.7 Md Group Address : 239.0.89.74
Number of VPN SGs : 1 Uptime : 0d 00:00:20
MT IfIndex : 24605 Egress Fwding Rate : 165.7 kbps
VPN Group Address : 239.1.0.2 VPN Source Address : 10.2.102.1
State : RX Joined
Expiry Timer : 0d 00:02:39
===============================================================================
PIM Selective provider tunnels
===============================================================================
Md Source Address : 239.200.200.7 Md Group Address : 239.0.89.75
Number of VPN SGs : 1 Uptime : 0d 00:00:20
MT IfIndex : 24606 Egress Fwding Rate : 165.7 kbps
VPN Group Address : 239.1.0.3 VPN Source Address : 10.2.102.1
State : RX Joined
Expiry Timer : 0d 00:02:39
===============================================================================
*B:node-6#
Output Example for Rosen MVPN S-PMSI Tunnel
B:Dut-E# show router 100 pim s-pmsi
===============================================================================
PIM Selective provider tunnels
===============================================================================
MD Src Address MT Index Num VPN SGs MD RP for ASM State
MD Grp Address Multistream ID
-------------------------------------------------------------------------------
10.20.1.5 5798467 1 N/A TX Joined
233.0.0.5 5
10.20.1.5 5798468 1 N/A TX Joined
233.0.0.6 6
10.20.1.5 5798469 1 N/A TX Joined
233.0.0.7 7
10.20.1.5 5798470 1021 N/A TX Joined
233.0.0.8 8
===============================================================================
PIM Selective provider tunnels Interfaces : 4
Output Example RX Tracking for RSVP S-PMSI Tunnel
*A:Dut-C# show router 1 pim s-pmsi
===============================================================================
PIM RSVP Spmsi tunnels
===============================================================================
P2mp ID Tunnel ID Ext Tunnel Adrs SPMSI Index Num VPN State
SGs
-------------------------------------------------------------------------------
0 0 10.20.1.4 1030144 1 RX Tracking
0 0 10.20.1.4 1030144 1 RX Tracking
===============================================================================
PIM RSVP Spmsi Interfaces : 2
===============================================================================
*A:Dut-C# show router 21 pim s-pmsi
====================================================================
PIM LDP Spmsi tunnels
====================================================================
Lsp ID Root Addr SPMSI Index Num VPN State
SGs
--------------------------------------------------------------------
0 10.20.1.4 1030144 1 RX Tracking
0 10.20.1.4 1030144 1 RX Tracking
====================================================================
PIM LDP Spmsi Interfaces : 2
====================================================================
*A:Dut-C#
Output Example RX Tracking for RSVP S-PMSI Tunnel
Detail
*A:Dut-C# show router 1 pim s-pmsi detail
===============================================================================
PIM RSVP Spmsi tunnels
===============================================================================
P2MP ID : 0 Tunnel ID : 0
Ext Tunnnel Addrs : 10.20.1.4 Spmsi IfIndex : 1030144
Number of VPN SGs : 1 Uptime : 0d 00:02:48
VPN Group Address : 239.100.0.0
VPN Source Address : 10.1.101.2
State : RX Tracking Mdt Threshold : 0
===============================================================================
PIM RSVP Spmsi tunnels
===============================================================================
P2MP ID : 0 Tunnel ID : 0
Ext Tunnnel Addrs : 10.20.1.4 Spmsi IfIndex : 1030144
Number of VPN SGs : 1 Uptime : 0d 00:02:47
VPN Group Address : ff0e:db8:225:100::
VPN Source Address : 2001:db8:1:101::2
State : RX Tracking Mdt Threshold : 0
===============================================================================
PIM RSVP Spmsi Interfaces : 2
===============================================================================
*A:Dut-C#
*A:Dut-C# show router 21 pim s-pmsi detail
===============================================================================
PIM LDP Spmsi tunnels
===============================================================================
LSP ID : 0
Root Addr : 10.20.1.4 Spmsi IfIndex : 1030144
Number of VPN SGs : 1 Uptime : 0d 00:03:35
VPN Group Address : 239.100.0.0
VPN Source Address : 10.1.101.2
State : RX Tracking Mdt Threshold : 0
===============================================================================
PIM LDP Spmsi tunnels
===============================================================================
LSP ID : 0
Root Addr : 10.20.1.4 Spmsi IfIndex : 1030144
Number of VPN SGs : 1 Uptime : 0d 00:03:34
VPN Group Address : ff0e:db8:225:100::
VPN Source Address : 2001:db8:1:101::2
State : RX Tracking Mdt Threshold : 0
===============================================================================
PIM LDP Spmsi Interfaces : 2
===============================================================================
*A:Dut-C#
Output Example TX Tracking for RSVP S-PMSI Tunnel
Detail
*A:Dut-C# show router 1 pim s-pmsi detail
===============================================================================
PIM RSVP Spmsi tunnels
===============================================================================
P2MP ID : 1 Tunnel ID : 61442
Ext Tunnnel Addrs : 10.20.1.4 Spmsi IfIndex : 74230
Number of VPN SGs : 1 Uptime : 0d 00:05:11
VPN Group Address : 239.100.0.0
VPN Source Address : 10.1.101.2
State : TX Join Pending Mdt Threshold : 1
Join Timer : N/A Holddown Timer : 0d 00:00:47
Receiver Count : 4
===============================================================================
PIM RSVP Spmsi tunnels
===============================================================================
P2MP ID : 1 Tunnel ID : 61443
Ext Tunnnel Addrs : 10.20.1.4 Spmsi IfIndex : 74231
Number of VPN SGs : 1 Uptime : 0d 00:05:10
VPN Group Address : ff0e:225:100::
VPN Source Address : 2001:db8:1:101::2
State : TX Join Pending Mdt Threshold : 1
Join Timer : N/A Holddown Timer : 0d 00:00:50
Receiver Count : 4
===============================================================================
PIM RSVP Spmsi Interfaces : 2
===============================================================================
*A:Dut-C#
*A:Dut-D# show router 21 pim s-pmsi detail
===============================================================================
PIM LDP Spmsi tunnels
===============================================================================
LSP ID : 8194
Root Addr : 10.20.1.4 Spmsi IfIndex : 74228
Number of VPN SGs : 1 Uptime : 0d 00:05:56
VPN Group Address : 239.100.0.0
VPN Source Address : 10.1.101.2
State : TX Join Pending Mdt Threshold : 1
Join Timer : N/A Holddown Timer : 0d 00:00:02
Receiver Count : 4
===============================================================================
PIM LDP Spmsi tunnels
===============================================================================
LSP ID : 8195
Root Addr : 10.20.1.4 Spmsi IfIndex : 74229
Number of VPN SGs : 1 Uptime : 0d 00:05:55
VPN Group Address : ff0e:db8:225:100::
VPN Source Address : 2001:db8:1:101::2
State : TX Join Pending Mdt Threshold : 1
Join Timer : N/A Holddown Timer : 0d 00:00:05
Receiver Count : 4
===============================================================================
PIM LDP Spmsi Interfaces : 2
===============================================================================
*A:Dut-D#
Label |
Description |
---|---|
MD Grp Address |
The IP multicast group address for which this entry contains information |
MD Src Address |
The source address of the multicast sender. The value is 0 if the type is configured as starg. The address of the Rendezvous Point (RP) displays if the type is configured as starRP. |
MT Index |
The index number |
Num VP SGs |
The VPN number |
s-pmsi
Syntax
s-pmsi [source mdSrcAddr] [group mdGrpAddr] [vprn-source vprnSrcAddr vprn-group vprnGrpAddr]
Context
[Tree] (clear>router>pim s-pmsi)
Full Context
clear router pim s-pmsi
Description
This command clears PIM selective provider multicast service interface cache.
Parameters
- mdSrcAddr
-
Clears the specified source address used for Multicast Distribution Tree (MDT).
- mdGrpAddr
-
Clears the specified group address used for Multicast Distribution Tree (MDT).
- vprnSrcAddr
-
Clears the specified source address of the multicast sender.
- vprnGrpAddr
-
Clears the specified multicast group address.
Platforms
All
s11
s11
Syntax
s11
Context
[Tree] (show>subscr-mgmt>gtp s11)
Full Context
show subscriber-mgmt gtp s11
Description
Commands in this context display information related to established S11 connections.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
s11
Syntax
s11
Context
[Tree] (show>router>gtp s11)
Full Context
show router gtp s11
Description
Commands in this context display S11 information.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
saa
saa
Syntax
saa [test-name] [owner test-owner]
Context
[Tree] (show saa)
Full Context
show saa
Description
This command displays information about the SAA test.
If no specific test is specified a summary of all configured tests is displayed.
If a specific test is specified then detailed test results for that test are displayed for the last three occurrences that this test has been executed, or since the last time the counters have been reset via a system reboot or clear command.
Parameters
- test-name
-
Specifies the optional parameter is used to enter the name of the SAA test for which the information needs to be displayed. The test name must already be configured in the config>saa>test context.
- test-owner
-
Specifies the owner of an SAA operation, up to 32 characters. If a test-owner value is not specified, tests created by the CLI have a default owner "TiMOS CLI”.
Platforms
All
Output
The following output is an example of SAA test information. SAA Field Descriptions describes the SAA test fields.
Output Example*A:bksim130>config>saa>test>trap-gen# show saa mySaaPingTest1
===============================================================================
SAA Test Information
===============================================================================
Test name : mySaaPingTest1
Owner name : TiMOS CLI
Description : N/A
Accounting policy : None
Administrative status : Disabled
Test type : icmp-ping 11.22.33.44
Trap generation : probe-fail-enable probe-fail-threshold 3
test-fail-enable test-fail-threshold 2
test-completion-enable
Test runs since last clear : 0
Number of failed test runs : 0
Last test result : Undetermined
-------------------------------------------------------------------------------
Threshold
Type Direction Threshold Value Last Event Run #
-------------------------------------------------------------------------------
Jitter-in Rising None None Never None
Falling None None Never None
Jitter-out Rising None None Never None
Falling None None Never None
Jitter-rt Rising None None Never None
Falling None None Never None
Latency-in Rising None None Never None
Falling None None Never None
Latency-out Rising None None Never None
Falling None None Never None
Latency-rt Rising None None Never None
Falling None None Never None
Loss-in Rising None None Never None
Falling None None Never None
Loss-out Rising None None Never None
Falling None None Never None
Loss-rt Rising None None Never None
Falling None None Never None
===============================================================================
*A:bksim130>config>saa>test>trap-gen#
*A:bksim130>config>saa>test>trap-gen$ show saa mySaaTraceRouteTest1
===============================================================================
SAA Test Information
===============================================================================
Test name : mySaaTraceRouteTest1
Owner name : TiMOS CLI
Description : N/A
Accounting policy : None
Administrative status : Disabled
Test type : icmp-trace 11.22.33.44
Trap generation : test-fail-enable test-completion-enable
Test runs since last clear : 0
Number of failed test runs : 0
Last test result : Undetermined
-------------------------------------------------------------------------------
Threshold
Type Direction Threshold Value Last Event Run #
-------------------------------------------------------------------------------
Jitter-in Rising None None Never None
Falling None None Never None
Jitter-out Rising None None Never None
Falling None None Never None
Jitter-rt Rising None None Never None
Falling None None Never None
Latency-in Rising None None Never None
Falling None None Never None
Latency-out Rising None None Never None
Falling None None Never None
Latency-rt Rising None None Never None
Falling None None Never None
Loss-in Rising None None Never None
Falling None None Never None
Loss-out Rising None None Never None
Falling None None Never None
Loss-rt Rising None None Never None
Falling None None Never None
===============================================================================
*A:bksim130>config>saa>test>trap-gen$
show saa <test-name>
CFM Loopback:
===============================================================================
SAA Test Information
===============================================================================
Test name : CFMLoopbackTest
Owner name : TiMOS CLI
Description : N/A
Accounting policy : 1
Continuous : Yes
Administrative status : Enabled
Test type : eth-cfm-
loopback 00:01:01:01:01:01 mep 1 domain 1 association 1 interval 1 count 10
Trap generation : None
Test runs since last clear : 1
Number of failed test runs : 0
Last test result : Success
-------------------------------------------------------------------------------
Threshold
Type Direction Threshold Value Last Event Run #
-------------------------------------------------------------------------------
Jitter-in Rising None None Never None
Falling None None Never None
Jitter-out Rising None None Never None
Falling None None Never None
Jitter-rt Rising None None Never None
Falling None None Never None
Latency-in Rising None None Never None
Falling None None Never None
Latency-out Rising None None Never None
Falling None None Never None
Latency-rt Rising None None Never None
Falling None None Never None
Loss-in Rising None None Never None
Falling None None Never None
Loss-out Rising None None Never None
Falling None None Never None
Loss-rt Rising None None Never None
Falling None None Never None
===============================================================================
Test Run: 1
Total number of attempts: 10
Number of requests that failed to be sent out: 0
Number of responses that were received: 10
Number of requests that did not receive any response: 0
Total number of failures: 0, Percentage: 0
(in us) Min Max Average Jitter
Outbound : 0.000 0.000 0.000 0
Inbound : 0.000 0.000 0.000 0
Roundtrip : 10200 10300 10250 100
Per test packet:
Sequence Result Delay(us)
1 Response Received 10300
2 Response Received 10300
3 Response Received 10300
4 Response Received 10200
5 Response Received 10300
6 Response Received 10200
7 Response Received 10300
8 Response Received 10200
9 Response Received 10300
10 Response Received 10300
=======================================================================
CFM Traceroute:
===============================================================================
SAA Test Information
===============================================================================
Test name : CFMLinkTraceTest
Owner name : TiMOS CLI
Description : N/A
Accounting policy : None
Continuous : Yes
Administrative status : Enabled
Test type : eth-cfm-
linktrace 8A:DB:01:01:00:02 mep 1 domain 1 association 1 interval 1
Trap generation : None
Test runs since last clear : 1
Number of failed test runs : 0
Last test result : Success
-------------------------------------------------------------------------------
Threshold
Type Direction Threshold Value Last Event Run #
-------------------------------------------------------------------------------
Jitter-in Rising None None Never None
Falling None None Never None
Jitter-out Rising None None Never None
Falling None None Never None
Jitter-rt Rising None None Never None
Falling None None Never None
Latency-in Rising None None Never None
Falling None None Never None
Latency-out Rising None None Never None
Falling None None Never None
Latency-rt Rising None None Never None
Falling None None Never None
Loss-in Rising None None Never None
Falling None None Never None
Loss-out Rising None None Never None
Falling None None Never None
Loss-rt Rising None None Never None
Falling None None Never None
===============================================================================
Test Run: 1
HopIdx: 1
Total number of attempts: 3
Number of requests that failed to be sent out: 0
Number of responses that were received: 3
Number of requests that did not receive any response: 0
Total number of failures: 0, Percentage: 0
(in ms) Min Max Average Jitter
Outbound : 0.000 0.000 0.000 0.000
Inbound : 0.000 0.000 0.000 0.000
Roundtrip : 2.86 3.67 3.15 0.047
Per test packet:
Sequence Outbound Inbound RoundTrip Result
1 0.000 0.000 3.67 Response Received
2 0.000 0.000 2.92 Response Received
3 0.000 0.000 2.86 Response Received
HopIdx: 2
Total number of attempts: 3
Number of requests that failed to be sent out: 0
Number of responses that were received: 3
Number of requests that did not receive any response: 0
Total number of failures: 0, Percentage: 0
(in ms) Min Max Average Jitter
Outbound : 0.000 0.000 0.000 0.000
Inbound : 0.000 0.000 0.000 0.000
Roundtrip : 4.07 4.13 4.10 0.005
Per test packet:
Sequence Outbound Inbound RoundTrip Result
1 0.000 0.000 4.10 Response Received
2 0.000 0.000 4.13 Response Received
3 0.000 0.000 4.07 Response Received
==================================
CFM Two Way Delay Measurement:
===============================================================================
SAA Test Information
===============================================================================
Test name : CFMTwoWayDelayTest
Owner name : TiMOS CLI
Description : N/A
Accounting policy : None
Continuous : Yes
Administrative status : Enabled
Test type : eth-cfm-two-way-
delay 00:01:01:01:01:01 mep 1 domain 1 association 1 interval 1
Trap generation : None
Test runs since last clear : 1
Number of failed test runs : 0
Last test result : Success
-------------------------------------------------------------------------------
Threshold
Type Direction Threshold Value Last Event Run #
-------------------------------------------------------------------------------
Jitter-in Rising None None Never None
Falling None None Never None
Jitter-out Rising None None Never None
Falling None None Never None
Jitter-rt Rising None None Never None
Falling None None Never None
Latency-in Rising None None Never None
Falling None None Never None
Latency-out Rising None None Never None
Falling None None Never None
Latency-rt Rising None None Never None
Falling None None Never None
Loss-in Rising None None Never None
Falling None None Never None
Loss-out Rising None None Never None
Falling None None Never None
Loss-rt Rising None None Never None
Falling None None Never None
...
===============================================================================
Test Run: 1
HopIdx: 1
Total number of attempts: 3
Number of requests that failed to be sent out: 0
Number of responses that were received: 3
Number of requests that did not receive any response: 0
Total number of failures: 0, Percentage: 0
Total number of failures: 0, Percentage: 0
(in us) Min Max Average Jitter
Outbound : 5095 5095 5095 0
Inbound : 5095 5095 0.000 0
Roundtrip : 10190 10190 10190 0
Per test packet:
Sequence (in us) Outbound Inbound Delay Delay variation
1 5195 5195 10190 0
2 5195 5195 10190 0
3 5195 5195 10190 0
...
===============================================================================
Label |
Description |
---|---|
Test Name |
Specifies the name of the test. |
Owner Name |
Specifies the owner of the test. |
Description |
Specifies the description for the test type. |
Accounting policy |
Specifies the associated accounting policy ID. |
Administrative status |
Specifies whether the administrative status is enabled or disabled. |
Test type |
Specifies the type of test configured. |
Trap generation |
Specifies the trap generation for the SAA test. |
Test runs since last clear |
Specifies the total number of tests performed since the last time the tests were cleared. |
Number of failed tests run |
Specifies the total number of tests that failed. |
Last test run |
Specifies the last time a test was run. |
Threshold type |
Indicates the type of threshold event being tested, jitter-event, latency-event, or loss-event, and the direction of the test responses received for a test run: in — inbound out — outbound rt — roundtrip |
Direction |
Indicates the direction of the event threshold, rising or falling. |
Threshold |
Displays the configured threshold value. |
Value |
Displays the measured crossing value that triggered the threshold crossing event. |
Last event |
Indicates the time that the threshold crossing event occurred. |
Run # |
Indicates what test run produced the specified values. |
saa
Syntax
saa-test [test-name [owner test-owner]]
Context
[Tree] (clear saa)
Full Context
clear saa
Description
This command clears the SAA results for the latest and the history for this test. If the test name is omitted, all the results for all tests are cleared.
Parameters
- test-name
-
Specifies the name of the SAA test. The test name must already be configured in the config>saa>test context.
- test-owner
-
Specifies the owner of an SAA operation up to 32 characters.
Platforms
All
saii-type2-using
saii-type2-using
Syntax
saii-type2-using global-id[:prefix[:ac-id]]
Context
[Tree] (show>service saii-type2-using)
Full Context
show service saii-type2-using
Description
This command displays the SDP used by a spoke SDP FEC with a specified FEC129 Type 2 SAII.
Parameters
- global-id[:prefix[:ac-id]]
-
Specifies the switch-point information using SAII-Type2.
Platforms
All
Output
The following output is an example of SAII information.
Output Example*A:Dut-E# show service saii-type2-using 3:10.20.1.3:1
===================================================================
Service Switch-Point Information
===================================================================
SvcId Oper-SdpBind SAII-Type2
-------------------------------------------------------------------
2147483598 17407:4294967195 3:10.20.1.3:1
-------------------------------------------------------------------
Entries found: 1
===================================================================
sap
sap
Syntax
sap {all | sap-id}
Context
[Tree] (show>subscr-mgmt>errors sap)
Full Context
show subscriber-mgmt errors sap
Description
This command sorts all the subscriber errors by SAP.
Parameters
- all
-
Shows all errors starting with the lowest SAP index.
- sap-id
-
Shows only the error of a specific SAP index.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber management errors listed by SAP.
Output ExampleA:BNG-2# show subscriber-mgmt errors sap all
===============================================================================
Subscriber management errors
===============================================================================
-------------------------------------------------------------------------------
SAP : 1/1/20:841
-------------------------------------------------------------------------------
Time : 2016/06/23 17:35:46.0
Service : 1000
MAC : 00:00:10:10:12:13
Error : No Offer from DHCP server after Discover from DHCP client
Extra : DHCPv4
Time : 2016/06/23 17:35:16.0
Service : 1000
MAC : 00:00:10:10:12:13
Error : No Offer from DHCP server after Discover from DHCP client
Extra : DHCPv4
===============================================================================
Subscriber Management SAP Error Field Descriptions describes subscriber management SAP error output fields.
Field |
Description |
---|---|
SAP |
The SAP ID associated with the error |
Time |
The time this error was reported to the subscriber management errors subsystem |
Service |
The service ID associated with the error |
MAC |
The MAC address associated with the error |
Error |
The error that occurred on the SAP |
Extra |
Extra information about the error that occurred |
sap
Syntax
sap sap-id static-isids [range-id range-id]
sap sap-id dist-cpu-protection [detail]
sap sap-id detail
sap sap-id encap-group group-name [member encap-id] [encap-detail | encap-stats]
sap sap-id encap-group
sap sap-id [ base | dhcp | mc-ring | mcac | mrp | qos | sap-stats | stats | stp | sub-mgmt | ipsec-gw]
sap sap-id [circuit-id circuit-id] [mac ieee-address] [remote-id remote-id] host-lockout-policy [summary]
sap queue-depth [queue queue-id] [ingress | egress]
sap
sap sap-id static-isids mfib
sap sap-id queue-group-redirection [ingress | egress]
Context
[Tree] (show>service>id sap)
Full Context
show service id sap
Description
Displays information for the SAPs associated with the service.
If no optional parameters are specified, a summary of all associated SAPs is displayed.
Parameters
- sap-id
-
The ID that displays SAPs for the service.
- detail
-
Displays detailed information for the SAP. For dist-cpu-protection, detail includes the adapted operational rate parameters in the CLI output. The adapted Oper. parameters are only applicable if the policer is instantiated (for example, if the associated forwarding plane is operational, or for an interface if there is a physical port configured for the interface, or if the dynamic policers are allocated), otherwise values of 0 kb/s, and so on, are displayed.
- static-isids
-
Displays static ISIDs for the SAP.
- range-id
-
Specifies the range ID.
- dist-cpu-protection
-
Displays information about the distributed CPU protection policy and parameters associated with the SAP.
- group-name
-
Specifies the group name, up to 32 characters in length.
- encap-id
-
Specifies the encapsulation ID.
- encap-detail
-
Displays encapsulation details for the specified encapsulation ID.
- encap-stats
-
Displays encapsulation statistics.
- encap-group
-
Displays the encapsulation group.
- base
-
Displays base information.
- dhcp
-
Displays DHCP information.
- mc-ring
-
Displays MC ring information.
- mcac
-
Displays MCAC information.
- mrp
-
Displays MRP information.
- qos
-
Displays QoS information.
- sap-stats
-
Displays SAP statistics.
- stats
-
Displays statistics.
- stp
-
Displays STP information.
- sub-mgmt
-
Displays subscriber management information.
- ipsec-gw
-
Displays IPSEC gateway information.
- circuit-id
-
Specifies the circuit ID, up to 256 characters.
- ieee-address
-
Specifies the IEEE address, up to 30 characters.
- remote-id
-
Specifies the remote-ID, up to 256 characters.
- host-lockout-policy
-
Displays the host lockout policy.
- summary
-
Displays summary information.
- queue-id
-
Specifies the queue ID.
- ingress
-
Displays ingress information.
- egress
-
Displays egress information.
- mfib
-
Displays MFIB information.
- queue-group-redirection
-
The output lists the queue group name and the instances configured in the related queue group redirect list. For each instance, the FP (for ingress) and port (for egress) is displayed. If there is a mismatch between the SAP and redirect list configuration and the queue group instance configuration, this is highlighted.
- ingress
-
Displays information for the ingress policy.
- egress
-
Displays information for the egress policy.
Platforms
All
Output
The following output is an example of SAP information, and Show Service-ID SAP Field Descriptions describes the output fields.
Output Exampleshow service id "BD20023" sap lag-1:200 detail
===============================================================================
Service Access Points(SAP)
===============================================================================
Service Id : 20023
SAP : lag-1:200 Encap : q-tag
Description : (Not Specified)
Admin State : Up Oper State : Up
Flags : None
Multi Svc Site : None
Last Status Change : 02/09/2023 15:35:22
Last Mgmt Change : 02/09/2023 15:35:12
Sub Type : regular
Split Horizon Group: (Not Specified)
Etree Root Leaf Tag: Disabled Etree Leaf Tag : 0
Etree Leaf AC : Disabled
Max Nbr of MAC Addr: No Limit Total MAC Addr : 2
Learned MAC Addr : 2 Static MAC Addr : 0
OAM MAC Addr : 0 DHCP MAC Addr : 0
Host MAC Addr : 0 Intf MAC Addr : 0
SPB MAC Addr : 0 Cond MAC Addr : 0
BGP EVPN Addr : 0 EVPN Static Addr : 0
Admin MTU : 1518 Oper MTU : 1518
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
qinq-pbit-marking : both
Egr Agg Rate Limit : max
Limit Unused BW : Disabled
ARP Reply Agent : Disabled Host Conn Verify : Disabled
SHCV pol IPv4 : None
Mac Learning : Enabled Discard Unkwn Srce: Disabled
Mac Aging : Enabled Mac Pinning : Disabled
BPDU Translation : Disabled
L2PT Termination : Disabled
Vlan-translation : None
Qinq-vlan- Qinq-vlan-
translation : None translation Ids : None
Acct. Pol : None Collect Stats : Disabled
Anti Spoofing : None Dynamic Hosts : Enabled
Avl Static Hosts : 0 Tot Static Hosts : 0
Calling-Station-Id : n/a
Application Profile: None
Transit Policy : None
Oper Group : (none) Monitor Oper Grp : (none)
Host Lockout Plcy : n/a
Lag Link Map Prof : (none)
Lag Per Link Hash
Class : 1 Weight : 1
Oper Class : 1 Oper Weight : 1
Override : false
Cflowd : Disabled
Bandwidth : Not-Applicable
Oper DCpu Prot Pol : _default-access-policy
MCAC Policy Name : MCAC Const Adm St : Enable
MCAC Max Unconst BW: no limit MCAC Max Mand BW : no limit
MCAC In use Mand BW: 0 MCAC Avail Mand BW: unlimited
MCAC In use Opnl BW: 0 MCAC Avail Opnl BW: unlimited
Use LAG port weight: no
MCAC If-Policy Name:
Restr MacUnpr Dst : Disabled (oper: Disabled)
Auto Learn Mac Prot: Disabled (oper: Disabled)
ALMP Exclude List : <none>
Oper ALMP Excl List: <none>
RestMacProtSrc Act : none (oper: Discard-frame)
Time to RetryReset : never Retries Left : 3
Mac Move : Blockable Blockable Level : Tertiary
Auth Policy : None
DestMac Rewrite : Disabled
Proc CPM Tfc Sap Dn: Disabled
SendBvplsEvpnFlush : Enabled
Bgp-Vpls MH VeId : <none>
-------------------------------------------------------------------------------
ETH-CFM SAP specifics
-------------------------------------------------------------------------------
Tunnel Faults : n/a AIS : Disabled
MC Prop-Hold-Timer : n/a V-MEP Filtering : Disabled
Squelch Levels : None
Squelch Ctag Levels: None
Collect Lmm Stats : Disabled
LMM FC Stats : None
LMM FC In Prof : None
-------------------------------------------------------------------------------
Stp Service Access Point specifics
-------------------------------------------------------------------------------
Stp Admin State : Up Stp Oper State : Down
Core Connectivity : Down
Port Role : N/A Port State : Forwarding
Port Number : N/A Port Priority : 128
Port Path Cost : 10 Auto Edge : Enabled
Admin Edge : Disabled Oper Edge : N/A
Link Type : Pt-pt BPDU Encap : Dot1d
Root Guard : Disabled Active Protocol : N/A
Last BPDU from : N/A
CIST Desig Bridge : N/A Designated Port : N/A
Forward transitions: 0 Bad BPDUs rcvd : 0
Cfg BPDUs rcvd : 0 Cfg BPDUs tx : 0
TCN BPDUs rcvd : 0 TCN BPDUs tx : 0
TC bit BPDUs rcvd : 0 TC bit BPDUs tx : 0
RST BPDUs rcvd : 0 RST BPDUs tx : 0
MST BPDUs rcvd : 0 MST BPDUs tx : 0
-------------------------------------------------------------------------------
ARP host
-------------------------------------------------------------------------------
Admin State : outOfService
Host Limit : 1 Min Auth Interval : 15 minutes
-------------------------------------------------------------------------------
QOS
-------------------------------------------------------------------------------
Ingress qos-policy : 1 Egress qos-policy : 1
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
Ing ip-match tag : none Ing ipv6-match tag: none
I. Sched Pol : (Not Specified)
E. Sched Pol : (Not Specified)
I. Policer Ctl Pol : (Not Specified)
E. Policer Ctl Pol : (Not Specified)
I. QGrp Redir. List: (Not Specified)
E. QGrp Redir. List: (Not Specified)
Hw Agg Shaper Q Set: No
Hw Agg Shpr QSet Sz: 0
Hw Agg Shpr In-Use : No
-------------------------------------------------------------------------------
DHCP
-------------------------------------------------------------------------------
Description : (Not Specified)
Admin State : Down Lease Populate : 0
DHCP Snooping : Down Action : Keep
Proxy Admin State : Down
Proxy Lease Time : N/A
Emul. Server Addr : Not Configured
-------------------------------------------------------------------------------
DHCP6
-------------------------------------------------------------------------------
Description : (Not Specified)
LDRA : Enabled
Interface-type : client-facing
Interface-Id : ascii-tuple
Remote-Id : mac
-------------------------------------------------------------------------------
Subscriber Management
-------------------------------------------------------------------------------
Admin State : Down MAC DA Hashing : False
Def Sub-Id : None
Def Sub-Profile : None
Def SLA-Profile : None
Def Inter-Dest-Id : None
Def App-Profile : None
Sub-Ident-Policy : None
Subscriber Limit : 1
Single-Sub-Parameters
Prof Traffic Only : False
Non-Sub-Traffic : N/A
Static host management
MAC learn options : N/A
-------------------------------------------------------------------------------
Sap Aggregate Stats
-------------------------------------------------------------------------------
Packets Octets
Ingress
Aggregate Offered : 2 136
Aggregate Forwarded : 2 136
Aggregate Dropped : 0 0
Egress
Aggregate Forwarded : 674 50140
Aggregate Dropped : 0 0
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Last Cleared Time : N/A
Packets Octets
CPM Ingress : 92 5740
Forwarding Engine Stats
Dropped : 0 0
Received Valid : 2 136
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 2 136
Off. Managed : 0 0
Queueing Stats(Ingress QoS Policy 1)
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 2 136
Queueing Stats(Egress QoS Policy 1)
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
For. In/InplusProf : 674 50140
For. Out/ExcProf : 0 0
-------------------------------------------------------------------------------
Sap per Queue stats
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 11 (Multipoint) (Priority)
Off. Combined : 2 136
Off. Managed : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 2 136
Egress Queue 1
For. In/InplusProf : 674 50140
For. Out/ExcProf : 0 0
Dro. In/InplusProf : 0 0
Dro. Out/ExcProf : 0 0
===============================================================================
show service id 9 sap 1/1/10:1 queue-depth
===============================================================================
Queue Depth Information (Ingress SAP)
===============================================================================
-------------------------------------------------------------------------------
Name : 9->1/1/10:1->1
MBS : Def
-------------------------------------------------------------------------------
Queue Depths (percentage)
-------------------------------------------------------------------------------
0%-10% 11%-20% 21%-30% 31%-40% 41%-50% 51%-60% 61%-70% 71%-80% 81%-90% 91%-100%
-------------------------------------------------------------------------------
100.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
-------------------------------------------------------------------------------
Average Elapsed Time : 0d 00:00:30
Wghtd Avg Queue Polling Interval: 100 ms
-------------------------------------------------------------------------------
===============================================================================
===============================================================================
Queue Depth Information (Egress SAP)
===============================================================================
-------------------------------------------------------------------------------
Name : 9->1/1/10:1->1
MBS : Def
Violation Threshold Percnt: xx.xx
Violation Total Count : xxx
Violation Last Seen : Thu Mar 26 12:39:33 PDT 2020
-------------------------------------------------------------------------------
Queue Depths (percentage)
-------------------------------------------------------------------------------
0%-10% 11%-20% 21%-30% 31%-40% 41%-50% 51%-60% 61%-70% 71%-80% 81%-90% 91%-100%
-------------------------------------------------------------------------------
100.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
-------------------------------------------------------------------------------
Average Elapsed Time : 0d 00:11:11
Wghtd Avg Queue Polling Interval : 100 ms
Wghtd Avg HiWtrMark Polling Interval: 1000 s
-------------------------------------------------------------------------------
===============================================================================
show service id 1 sap 1/1/1 queue-group-redirection
===============================================================================
Queue Group Redirect List Information (Ingress SAP)
===============================================================================
Queue Group Redirect List : list1
Type : vxlan-vni
Queue Group : qg1
-------------------------------------------------------------------------------
Match Instance FP
-------------------------------------------------------------------------------
1 1 1/1
2 2 1/1
3 3 1/1 : mismatch
-------------------------------------------------------------------------------
===============================================================================
===============================================================================
Queue Group Redirect List Information (Egress SAP)
===============================================================================
Queue Group Redirect List : list1
Type : vxlan-vni
Queue Group : qg1
-------------------------------------------------------------------------------
Match Instance Port
-------------------------------------------------------------------------------
1 1 1/1/1
2 2 1/1/1
3 3 1/1/1 : mismatch
-------------------------------------------------------------------------------
===============================================================================
Label |
Description |
---|---|
Service Access Points(SAP) |
|
Service Id |
The service identifier. |
SAP |
The SAP and qtag. |
Encap |
The encapsulation type of the SAP. |
Ethertype |
Specifies an Ethernet type II Ethertype value. |
Admin State |
The administrative state of the SAP. |
Oper State |
The operating state of the SAP. |
Flags |
Specifies the conditions that affect the operating status of this SAP. Display output includes: ServiceAdminDown, SapAdminDown, InterfaceAdminDown, PortOperDown, PortMTUTooSmall, L2OperDown, SapIngressQoSMismatch, SapEgressQoSMismatch, RelearnLimitExceeded, RxProtSrcMac, ParentIfAdminDown, NoSapIpipeCeIpAddr, SapParamMismatch, CemSapNoEcidOrMacAddr, StandByForMcRing, ServiceMTUTooSmall, NoSapEpipeRingNode. |
Last Status Change |
Specifies the time of the most recent operating status change to this SAP. |
Last Mgmt Change |
Specifies the time of the most recent management-initiated change to this SAP. |
Admin MTU |
The desired largest service frame size (in octets) that can be transmitted through the SAP to the far-end router, without requiring the packet to be fragmented. |
Oper MTU |
The actual largest service frame size (in octets) that can be transmitted through the SAP to the far-end router, without requiring the packet to be fragmented. |
Restr MacUnpr Dst |
The administrative and operational state of the restrict unprotected destination MAC (restrict-unprotected-dst) functionality. |
Auto Learn Mac Prot |
The administrative and operational state of the protected MAC auto learning (auto-learn-mac-protect) functionality. |
RestMacProtSrc Act |
The administrative and operational state of the restrict protected source MAC (restrict-protected-src) functionality. |
QOS |
|
Ingress qos-policy |
The ingress QoS policy ID assigned to the SAP. |
Egress qos-policy |
The egress QoS policy ID assigned to the SAP. |
Ingress Filter-Id |
The ingress filter policy ID assigned to the SAP. |
Egress Filter-Id |
The egress filter policy ID assigned to the SAP. |
Acct. Pol |
The accounting policy ID assigned to the SAP. |
Collect Stats |
Specifies whether collect stats is enabled. |
Dropped |
The number of packets and octets dropped due to SAP state, ingress MAC or IP filter, same segment discard, bad checksum, etc. |
Received Valid |
The number of valid packets and octets received on the SAP. |
Off. HiPrio |
The number of high priority packets and octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
Off. LowPrio |
The number of low priority packets and octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
Off. Uncolor |
The number of uncolored packets and octets, as determined by the SAP ingress QoS policy, offered by the Pchip to the Qchip. |
Dro. HiPrio |
The number of high priority packets and octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
Dro. LowPrio |
The number of low priority packets and octets, as determined by the SAP ingress QoS policy, dropped by the Qchip due to: MBS exceeded, buffer pool limit exceeded, etc. |
For. InProf |
The number of in-profile packets and octets (rate below CIR) forwarded by the ingress Qchip. |
For. OutProf |
The number of out-of-profile packets and octets discarded by the egress Qchip due to MBS exceeded, buffer pool limit exceeded, etc. |
Dro. InProf |
The number of in-profile packets and octets discarded by the egress Qchip due to MBS exceeded, buffer pool limit exceeded, etc. |
Dro. OutProf |
The number of out-of-profile packets and octets discarded by the egress Qchip due to MBS exceeded, buffer pool limit exceeded, etc. |
For. InProf |
The number of in-profile packets and octets (rate below CIR) forwarded by the egress Qchip. |
For. OutProf |
The number of out-of-profile packets and octets (rate above CIR) forwarded by the egress Qchip. |
Ingress TD Profile |
The profile ID applied to the ingress SAP. |
Egress TD Profile |
The profile ID applied to the egress SAP. |
Alarm Cell Handling |
The indication that OAM cells are being processed. |
AAL-5 Encap |
The AAL-5 encapsulation type. |
Mult Svc Site |
Specifies the customer’s multiservice site name. |
I. Sched Pol |
The ingress scheduler policy applied to the customer’s multiservice site. |
E. Sched Pol |
The egress scheduler policy applied to the customer’s multiservice site. |
HW Agg Shaper Q Set | Whether the hardware aggregate shaper queue sets are in use. |
HW Add Shpr QSet Sz | The size of the hardware aggregate shaper queue set. |
HW Agg Shpr In-Use | Whether hardware aggregate shapers are in use. |
LLF Admin State |
Displays the Link Loss Forwarding administrative state. |
LLF Oper State |
Displays the Link Loss Forwarding operational state. |
pw-port |
pw-id[:qtag1[.qtag2]] pw-id[:qtag1[.qtag2]] pw-2:1.1 |
DHCP6 | |
LDRA | The state of the Lightweight DHCPv6 Relay Agent:
|
Interface Type | The LDRA interface type:
|
Interface-Id | The format for the Interface ID option:
|
Remote-Id | The format for the Remote ID option:
|
The following output is an example of distributed CPU Protection Policer Output information.
Show Distributed CPU Protection Policer Output Fields describes distributed CPU Protection Policer output fields.
Output Example*A:nodeA# show service id 33 sap 1/1/3:33 dist-cpu-protection detail
===============================================================================
Service Access Points(SAP) 1/1/3:33
===============================================================================
Distributed CPU Protection Policy : test1
-------------------------------------------------------------------------------
Statistics/Policer-State Information
===============================================================================
-------------------------------------------------------------------------------
Static Policer
-------------------------------------------------------------------------------
Policer-Name : arp
Card/FP : 1/1 Policer-State : Conform
Protocols Mapped : arp
Exceed-Count : 0
Detec. Time Remain : 0 seconds Hold-Down Remain. : none
Operational (adapted) rate parameters:
Oper. Packets : 5 ppi Oper. Within : 8 seconds
Oper. Initial Delay: 6 packets
Oper. Depth : 0 packets
Policer-Name : dhcp
Card/FP : 1/1 Policer-State : Conform
Protocols Mapped : dhcp
Exceed-Count : 0
Detec. Time Remain : 0 seconds Hold-Down Remain. : none
Operational (adapted) rate parameters:
Oper. Kbps : 2343 kbps Oper. MBS : 240 kilobytes
Oper. Depth : 0 bytes
… (snip)
*A:nodaA# show service id 33 sap 1/1/3:34 dist-cpu-protection detail
===============================================================================
Service Access Points(SAP) 1/1/3:34
===============================================================================
Distributed CPU Protection Policy : test2
-------------------------------------------------------------------------------
Statistics/Policer-State Information
===============================================================================
Static Policer
-------------------------------------------------------------------------------
No entries found
-------------------------------------------------------------------------------
Local-Monitoring Policer
-------------------------------------------------------------------------------
Policer-Name : my-local-mon1
Card/FP : 1/1 Policer-State : conform
Protocols Mapped : arp, pppoe-pppoa
Exceed-Count : 0
All Dyn-Plcr Alloc. : False
Operational (adapted) rate parameters:
Oper. Packets : 10 ppi Oper. Within : 8 seconds
Oper. Initial Delay: 8 packets
Oper. Depth : 0 packets
-------------------------------------------------------------------------------
Dynamic-Policer (Protocol)
-------------------------------------------------------------------------------
Protocol(Dyn-Plcr) : arp
Card/FP : 1/1 Protocol-State : not-applicable
Exceed-Count : 0
Detec. Time Remain : 0 seconds Hold-Down Remain. : none
Dyn-Policer Alloc. : False
Operational (adapted) rate parameters: unknown
Protocol(Dyn-Plcr) : pppoe-pppoa
Card/FP : 1/1 Protocol-State : not-applicable
Exceed-Count : 0
Detec. Time Remain : 0 seconds Hold-Down Remain. : none
Dyn-Policer Alloc. : False
Operational (adapted) rate parameters: unknown
-------------------------------------------------------------------------------
Label |
Description |
---|---|
Distributed CPU Protection Policy |
The DCP policy assigned to the object. |
Policer-Name |
The configured name of the static policer |
Card/FP |
The card and FP identifier. FP identifies the instance of the FP (FastPath) chipset. Some cards have a single FP and some cards can contain multiple FPs (for example, an XCM can house multiple FPs via its two XMAs). |
Policer-State |
The state of the policer with the following potential values: |
Exceed — The policer has been detected as not conforming to the associated DCP policy parameters (for example, packets exceeded the configured rate and the DCP polling process identified this occurrence) |
|
Conform — The policer has been detected as conforming to the associated DCP policy parameters (rate) |
|
not-applicable — Newly-created policers or policers that are not currently instantiated. This includes policers configured on line cards that are not in service. |
|
Protocols Mapped |
A list of protocols that are configured to map to the particular policer. |
Oper. xyz fields |
The actual hardware may not be able to perfectly rate limit to the exact configured rate parameters in a DCP policy. In this case the configured rate parameters will be adapted to the closest supported rate. These adapted operational values are displayed in CLI when the detail keyword is included in the show command. The adapted Oper. parameters are only applicable if the policer is instantiated (for example, if the associated forwarding plane is operational, or for an interface if there is a physical port configured for the interface, or if the dynamic policers are allocated), otherwise values of 0 kb/s, and so on, are displayed. |
Oper. Kbps - The adapted "kilobits-per-second” value for DCP "kbps” rates |
|
Oper. MBS - The adapted "mbs size” value for DCP "kbps” rates |
|
Oper. Depth - The calculated policer bucket depth in packets (for DCP "packets” rates) or in bytes (for DCP "kbps” rates) |
|
Oper. Packets - The adapted "ppi” value for DCP "packets” rates |
|
Oper. Within - The adapted "within seconds” value for DCP "packets” rates |
|
Oper. Init. Delay - The adapted "initial-delay packets” value for DCP "packets” rates |
|
Exceed-Count |
The count of packets exceeding the policing parameters since the given policer was previously declared as conforming or newly-instantiated. This counter has the same behavior as the exceed counter in the DCP the log events, they are baselined (reset) when the policer transitions to conforming. |
Detec. Time Remain |
The remaining time in the detection-time countdown during which a policer in the exceed state is being monitored to see if it conforms again. |
Hold-Down Remain |
The remaining time in the hold-down countdown during which a policer is treating all packets as exceeding. |
All Dyn-Plcr Alloc. |
Indicates that all the dynamic enforcement policers have been allocated and instantiated for a given local-monitor. |
Dyn-Policer Alloc. |
Indicates that a dynamic policer has been instantiated. |
sap
Syntax
sap sap-id
Context
[Tree] (clear>service>id sap)
Full Context
clear service id sap
Description
This command clears information for the specified SAP.
Parameters
- sap-id
-
Specifies the physical port identifier portion of the SAP definition
Platforms
All
sap
Syntax
sap sap-id {all | cem | counters | stp | l2pt | mrp}
sap sap-id encap-group group-name [member encap-id]
Context
[Tree] (clear>service>statistics sap)
Full Context
clear service statistics sap
Description
This command clears SAP statistics for a SAP.
Parameters
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- all
-
Clears all SAP queue statistics and STP statistics.
- counters
-
Clears all queue statistics associated with the SAP.
- stp
-
Clears all STP statistics associated with the SAP.
- l2pt
-
Clears all L2PT statistics associated with the SAP.
- mrp
-
Clears all MRP statistics associated with the SAP.
- group-name
-
Specifies the group name, up to 32 characters.
- encap-id
-
Specifies the encapsulation ID.
Platforms
All
sap
Syntax
sap [sap-id] [level level] [primary-vlan-enabled vlan-id]
sap port port-id [level level] [primary-vlan-enabled vlan-id]
Context
[Tree] (show>eth-cfm>mip-instantiation sap)
Full Context
show eth-cfm mip-instantiation sap
Description
This command displays MIP creation information for SAPs.
Parameters
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- level
-
Specifies the MIP instantiation level.
- vlan-id
-
Specifies the VLAN ID to display.
- port-id
-
Specifies the port ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
sap
Syntax
sap sap-id [{ingress | egress}] [{detail | root-detail | thresholds | priority-info | depth}] [port port-id] [ arbiter {name | root }]
Context
[Tree] (show>qos>policer-hierarchy sap)
Full Context
show qos policer-hierarchy sap
Description
This command displays information about the policer hierarchy per SAP.
Parameters
- sap-id
-
Displays information about the specified SAP.
- ingress
-
Displays ingress SAP information.
- egress
-
Displays egress SAP information.
- detail
-
Displays detailed information.
- root-detail
-
Displays detailed information about the arbiter root.
- thresholds
-
Displays the threshold, parenting, rate, and traffic information related to a policer.
- priority-info
-
Displays the threshold information related to the root arbiter.
- depth
-
Displays the bucket depth, parenting, rate, and traffic information related to a policer.
- port-id
-
Displays information about the specified port.
- name
-
Displays information about the name of the QoS arbiter.
- root
-
Displays information about the arbiter root.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
Output
The following output is an example of SAP policer hierarchy information.
Output Example*A:PE-1# show qos policer-hierarchy sap 1/1/3:1
===============================================================================
Policer Hierarchy - Sap 1/1/3:1
===============================================================================
Ingress Policer Control Policy : cfhp-1
Egress Policer Control Policy :
-------------------------------------------------------------------------------
root (Ing)
|
| slot(1)
| Profile-preferred:Disabled
|
|--(A) : a3 (Sap 1/1/3:1)
| |
| |--(P) : Policer 1->1/1/3:1->4
| | |
| | | [Level 2 Weight 25]
| | | Assigned PIR:60000 Offered:0
| | | Consumed:0
| | |
| | | Assigned FIR:15000
| |
| |--(P) : Policer 1->1/1/3:1->3
| | |
| | | [Level 2 Weight 25]
| | | Assigned PIR:60000 Offered:0
| | | Consumed:0
| | |
| | | Assigned FIR:15000
| |
| |--(P) : Policer 1->1/1/3:1->2
| | |
| | | [Level 2 Weight 50]
| | | Assigned PIR:60000 Offered:0
| | | Consumed:0
| | |
| | | Assigned FIR:30000
|
|--(P) : Policer 1->1/1/3:1->5
| |
| | [Level 5 Weight 1]
| | Assigned PIR:10000 Offered:0
| | Consumed:0
| |
| | Assigned FIR:10000
|
|--(P) : Policer 1->1/1/3:1->1
| |
| | [Level 1 Weight 1]
| | Assigned PIR:100000 Offered:0
| | Consumed:0
| |
| | Assigned FIR:100000
root (Egr)
|
No Active Members Found on slot 1
===============================================================================
*A:PE-1#
*A:PE-1# show qos policer-hierarchy sap 1/1/3:1 detail
===============================================================================
Policer Hierarchy - Sap 1/1/3:1
===============================================================================
Ingress Policer Control Policy : cfhp-1
Egress Policer Control Policy :
-------------------------------------------------------------------------------
Legend :
(*) real-time dynamic value
(w) Wire rates
-------------------------------------------------------------------------------
root (Ing)
|
| slot(1)
| Profile-preferred:Disabled
| MaxPIR:100000
| ConsumedByChildren:0
| OperPIR:100000 OperFIR:100000
|
| DepthPIR:0 bytes
| Priority 8
| Oper Thresh Unfair:17408 Oper Thresh Fair:25600
| Association count:0
| Priority 7
| Oper Thresh Unfair:17408 Oper Thresh Fair:25600
| Association count:0
| Priority 6
| Oper Thresh Unfair:17408 Oper Thresh Fair:25600
| Association count:0
| Priority 5
| Oper Thresh Unfair:17408 Oper Thresh Fair:25600
| Association count:1
| Priority 4
| Oper Thresh Unfair:9728 Oper Thresh Fair:17408
| Association count:0
| Priority 3
| Oper Thresh Unfair:9728 Oper Thresh Fair:17408
| Association count:3
| Priority 2
| Oper Thresh Unfair:0 Oper Thresh Fair:8192
| Association count:0
| Priority 1
| Oper Thresh Unfair:0 Oper Thresh Fair:8192
| Association count:1
|
|--(A) : a3 (Sap 1/1/3:1)
| | MaxPIR:60000
| | ConsumedByChildren:0
| | OperPIR:60000 OperFIR:60000
| |
| | [Level 3 Weight 1]
| | Assigned PIR:60000 Offered:0
| | Consumed:0
| |
| | Assigned FIR:60000
| |
| |--(P) : Policer 1->1/1/3:1->4
| | | MaxPIR:60000 MaxCIR:20000
| | | CBS:25600 MBS:77824
| | | HiPrio:0
| | | Depth:0
| | |
| | | OperPIR:60000 OperCIR:20000
| | | OperFIR:15000
| | | PacketByteOffset:0
| | | StatMode: offered-total-cir
| | |
| | | [Level 2 Weight 25]
| | | Assigned PIR:60000 Offered:0
| | | Consumed:0
| | |
| | | Assigned FIR:15000
| |
| |--(P) : Policer 1->1/1/3:1->3
| | | MaxPIR:60000 MaxCIR:20000
| | | CBS:25600 MBS:77824
| | | HiPrio:0
| | | Depth:0
| | |
| | | OperPIR:60000 OperCIR:20000
| | | OperFIR:15000
| | | PacketByteOffset:0
| | | StatMode: offered-total-cir
| | |
| | | [Level 2 Weight 25]
| | | Assigned PIR:60000 Offered:0
| | | Consumed:0
| | |
| | | Assigned FIR:15000
| |
| |--(P) : Policer 1->1/1/3:1->2
| | | MaxPIR:60000 MaxCIR:20000
| | | CBS:25600 MBS:77824
| | | HiPrio:0
| | | Depth:0
| | |
| | | OperPIR:60000 OperCIR:20000
| | | OperFIR:30000
| | | PacketByteOffset:0
| | | StatMode: offered-total-cir
| | |
| | | [Level 2 Weight 50]
| | | Assigned PIR:60000 Offered:0
| | | Consumed:0
| | |
| | | Assigned FIR:30000
|
|--(P) : Policer 1->1/1/3:1->5
| | MaxPIR:10000 MaxCIR:10000
| | CBS:12800 MBS:12800
| | HiPrio:0
| | Depth:0
| |
| | OperPIR:10000 OperCIR:10000
| | OperFIR:10000
| | PacketByteOffset:0
| | StatMode: offered-total-cir
| |
| | [Level 5 Weight 1]
| | Assigned PIR:10000 Offered:0
| | Consumed:0
| |
| | Assigned FIR:10000
|
|--(P) : Policer 1->1/1/3:1->1
| | MaxPIR:100000 MaxCIR:0
| | CBS:0 MBS:126976
| | HiPrio:0
| | Depth:0
| |
| | OperPIR:100000 OperCIR:0
| | OperFIR:100000
| | PacketByteOffset:0
| | StatMode: offered-total-cir
| |
| | [Level 1 Weight 1]
| | Assigned PIR:100000 Offered:0
| | Consumed:0
| |
| | Assigned FIR:100000
root (Egr)
|
No Active Members Found on slot 1
===============================================================================
*A:PE-1#
Label |
Description |
---|---|
Policer Hierarchy - SAP |
Displays the SAP ID |
slot |
Displays the slot number |
(A) |
An arbiter, an object that is configured in the policy |
a3 |
Displays the name of the arbiter |
(P) |
Displays the policer name |
[Level X Weight XX] |
Displays the CIR level and weight configured in the policy |
Assigned PIR |
Displays the assigned PIR value |
Offered |
Displays the Offered PIR value |
Consumed |
Displays the amount of bandwidth consumed by the policer |
Assigned FIR |
Displays the assigned FIR based on weights of individual policers and the offered traffic |
sap
Syntax
sap sap-id [scheduler scheduler-name] [{ingress | egress}] [detail]
sap sap-id encap-group group-name [scheduler scheduler-name] [ member encap-id] [detail]
Context
[Tree] (show>qos>scheduler-hierarchy sap)
Full Context
show qos scheduler-hierarchy sap
Description
This command displays the scheduler hierarchy per SAP.
Parameters
- sap-id
-
Specifies the SAP assigned to the service.
- scheduler-name
-
The unique scheduler name created in the context of the scheduler policy
- ingress
-
The keyword to display ingress SAP scheduler stats.
- egress
-
The keyword to display egress SAP scheduler stats.
- group-name
-
Specifies the name of the encap-group and can be up to 32 ASCII characters.
- encap-id
-
Specifies the value of the single encap-id.
- detail
-
Displays detailed information.
Platforms
All
Output
The following output is an example of SAP scheduler hierarchy information, and Show QoS Scheduler-Hierarchy SAP Output Fields describes the SAP scheduler hierarchy fields.
Output Example===============================================================================
*A:Dut-A>config>service# show qos scheduler-hierarchy sap lag-1:1 ingress detail
===============================================================================
Scheduler Hierarchy - Sap lag-1:1
===============================================================================
Ingress Scheduler Policy: sched1
-------------------------------------------------------------------------------
Legend :
(*) real-time dynamic value
(otw) on-the-wire rates
(lmotw) last-mile-on-the-wire rates
B Bytes
-------------------------------------------------------------------------------
Root (Ing)
|
| slot(1)
|
|--(S) : sch1
| | AdminPIR:max AdminCIR:0 kbps(sum)
| | Limit Unused Bandwidth: disabled
| |
| | [Within CIR Level 0 Weight 0]
| | Assigned:0 kbps Offered:0 kbps
| | Consumed:0 kbps
| |
| | [Above CIR Level 0 Weight 0]
| | Assigned:0 kbps Offered:0 kbps
| | Consumed:0 kbps
| |
| | TotalConsumed:0 kbps
| | OperPIR:max
| |
| | [As Parent]
| | Rate:max
| | ConsumedByChildren:0 kbps
| |
| |--(P) : 1->lag-1:1(1/1/c1/1)->2
| | | AdminPIR:max AdminCIR:0 kbps
| | | Parent Limit Unused Bandwidth: not-found
| | | CBS:0 B MBS:8589934592 B
| | | Depth:0 B
| | | Low Drop Tail:0 B
| | |
| | | [Within CIR Level 0 Weight 1]
| | | Assigned:0 kbps Offered:0 kbps
| | | Consumed:0 kbps
| | |
| | | [Above CIR Level 1 Weight 1]
| | | Assigned:max Offered:0 kbps
| | | Consumed:0 kbps
| | | TotalConsumed:0 kbps
| | | OperPIR:max OperCIR:0 kbps
| | |
| | | PktByteOffset:add 0*
| | | OnTheWireRates:false
| | | ATMOnTheWireRates:false
| | | LastMileOnTheWireRates:false
| |
| |--(S) : Tier0Ingress:1->lag-1:1->1
| | | AdminPIR:10000000 kbps AdminCIR:0 kbps
| | | AdminFIR:0 kbps
| | | Parent Limit Unused Bandwidth: not-found
| | |
| | | [Within CIR Level 0 Weight 1]
| | | Assigned:0 kbps Offered:0 kbps
| | | Consumed:0 kbps
| | |
| | | [Above CIR Level 1 Weight 1]
| | | Assigned:10000000 kbps Offered:0 kbps
| | | Consumed:0 kbps
| | |
| | | TotalConsumed:0 kbps
| | | OperPIR:10000000 kbps
| | |
| | | [As Parent]
| | | OperPIR:10000000 kbps OperCIR:0 kbps
| | | OperFIR:0 kbps
| | | ConsumedByChildren:0 kbps
| | |
| | |--(Q) : 1->lag-1:1(1/1/c1/1)->1 1:1/1
| | | | AdminPIR:10000000 kbps AdminCIR:0 kbps
| | | | Parent Limit Unused Bandwidth: not-found
| | | | CBS:0 B
| | | | MBS:12582912 B
| | | | Depth:0 B
| | | | HighPlus Drop Tail:12582912 B
| | | | High Drop Tail:12582912 B
| | | | Low Drop Tail:11272192 B
| | | | Exceed Drop Tail:9961472 B
| | | |
| | | | [CIR Weight 1]
| | | | Assigned:0 kbps Offered:0 kbps
| | | | Consumed:0 kbps
| | | |
| | | | [PIR Weight 1]
| | | | Assigned:10000000 kbps Offered:0 kbps
| | | | Consumed:0 kbps
| | | | OperPIR:max OperCIR:0 kbps
| | | |
| | | | OperFIR:0 kbps
| | | |
| | | | PktByteOffset:add 0*
| | | | OnTheWireRates:false
| | | | ATMOnTheWireRates:false
| | | | LastMileOnTheWireRates:false
===============================================================================
*A:PE# show qos scheduler-hierarchy sap 1/1/1:1 egress detail
===============================================================================
Scheduler Hierarchy - Sap 1/1/1:1
===============================================================================
Egress Scheduler Policy : sp1
-------------------------------------------------------------------------------
Legend :
(*) real-time dynamic value
(w) Wire rates
B Bytes
-------------------------------------------------------------------------------
Root (Egr)
| slot(1)
|--(S) : s1
| | AdminPIR:200000 AdminCIR:10000(sum)
| | Limit Unused Bandwidth: disabled
| |
| |
| | [Within CIR Level 0 Weight 0]
| | Assigned:0 Offered:0
| | Consumed:0
| |
| | [Above CIR Level 0 Weight 0]
| | Assigned:0 Offered:0
| | Consumed:0
| |
| |
| | TotalConsumed:0
| | OperPIR:200000
| |
| | [As Parent]
| | Rate:200000
| | ConsumedByChildren:0
| |
| |
| |--(Q) : 1->1/1/1:1->1
| | | AdminPIR:10000 AdminCIR:10000
| | | Parent Limit Unused Bandwidth: not-found
| | | CBS:15360 B
| | | MBS:66048 B
| | | Depth:0 B
| | | HighPlus Drop Tail:66048 B
| | | High Drop Tail:66048 B
| | | Low Drop Tail:58368 B
| | | Exceed Drop Tail:52224 B
| | |
| | | [Within CIR Level 6 Weight 1]
| | | Assigned:10000 Offered:0
| | | Consumed:0
| | |
| | | [Above CIR Level 6 Weight 1]
| | | Assigned:10000 Offered:0
| | | Consumed:0
| | |
| | | TotalConsumed:0
| | | OperPIR:10000 OperCIR:10000
| | |
| | | PktByteOffset:add 0*
| | | OnTheWireRates:false
| | | ATMOnTheWireRates:false
| | | LastMileOnTheWireRates:false
| |
|
===============================================================================
Label |
Description |
---|---|
Admin CIR/PIR |
Specifies the configured value of CIR/PIR. |
Assigned CIR/PIR |
Specifies the PIR/CIR rate given to a member by that parent level. |
Offered CIR/PIR |
Specifies the offered load on that member. |
Consumed CIR/PIR |
Specifies the amount of scheduler bandwidth used by this member. |
S |
Displays the scheduler name and information. |
Q |
Displays the queue ID and information. |
P |
Displays the policer ID and information. |
sap
Syntax
sap sap-id [scheduler scheduler-name] [{ingress | egress}]
sap sap-id encap-group group-name [scheduler scheduler-name] [ member encap-id]
Context
[Tree] (show>qos>scheduler-stats sap)
Full Context
show qos scheduler-stats sap
Description
This command displays information about the scheduler stats per SAP.
Parameters
- sap-id
-
Displays information about the SAP and encapsulation value used to identify the SAP.
- scheduler-name
-
Displays information about the specified schedule.
- ingress
-
Display only the policy displayed on the ingress SAP.
- egress
-
Display only the policy displayed on the egress SAP.
- group-name
-
Specifies the name of the encap-group and can be up to 32 ASCII characters.
- encap-id
-
Specifies the value of the single encap-id.
Platforms
All
Output
The following output is an example of scheduler-stats SAP information, and Show QoS Scheduler-Stats SAP Output Fields describes the scheduler-stats SAP fields.
Output ExampleA:ALA-12# show qos scheduler-stats sap 1/1/4.1:0
==============================================================================
Scheduler Stats
==============================================================================
Scheduler Forwarded Packets Forwarded Octets
-----------------------------------------------------------------------------
Ingress Schedulers
All_traffic 0 0
NetworkControl 0 0
Egress Schedulers
All_traffic 0 0
Internet_be 0 0
Internet_priority 0 0
Internet_voice 0 0
NetworkControl 0 0
NonVoice 0 0
VPN_be 0 0
VPN_nc 0 0
VPN_priority 0 0
VPN_reserved 0 0
VPN_video 0 0
VPN_voice 0 0
Voice 0 0
=============================================================================
A:ALA-12#
A:ALA-12# show qos scheduler-stats sap 1/1/5:0 scheduler 1
==============================================================================
Scheduler Stats
==============================================================================
Scheduler Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
Ingress Schedulers
No Matching Entries.
Egress Schedulers
No Matching Entries.
==============================================================================
A:ALA-12#
A:ALA-12# show qos scheduler-stats sap 1/1/4.1:0 scheduler All_traffic
=============================================================================
Scheduler Stats
==============================================================================
Scheduler Forwarded Packets Forwarded Octets
------------------------------------------------------------------------------
Ingress Schedulers
All_traffic 0 0
Egress Schedulers
All_traffic 0 0
==============================================================================
A:ALA-12#
Label |
Description |
---|---|
Scheduler |
Displays the scheduler policy name. |
Forwarded Packets |
Displays the number of packets forwarded. |
Forwarded Octet |
Displays the number of octets forwarded. |
Ingress Schedulers |
Displays the egress scheduler name(s). |
Egress Schedulers |
Displays the ingress scheduler name(s). |
sap
Syntax
sap sap-id [egress] [ detail]
sap sap-id encap-group group-name [member encap-id] [detail]
Context
[Tree] (show>qos>agg-rate sap)
Full Context
show qos agg-rate sap
Description
This command displays the H-QoS aggregate rate limit per SAP or encap group.
Parameters
- sap sap-id
-
The port number and encapsulation value used to identify the SAP.
- egress
-
Displays egress SAP customer scheduler stats.
- group-name
-
Specifies the name of the encap-group and can be up to 32 ASCII characters.
- encap-id
-
Specifies the value of the single encap-id.
- detail
-
Displays detailed information.
Platforms
All
Output
The following output is an example of H-QoS aggregate rate limit per SAP output, and Show H-QoS Aggregate Rate Limit per SAP Output Fields describes the H-QoS aggregate rate limit per SAP fields.
Output Example*A:PE# show qos agg-rate sap 1/1/1:1 egress
===============================================================================
Aggregate Rate Information - Sap 1/1/1:1
===============================================================================
-------------------------------------------------------------------------------
Root (Egr)
| slot(1)
| AdminRate : 10000
| OperRate : 0
| Limit Unused Bandwidth : disabled
| OnTheWireRates : false
| LastMileOnTheWireRates : false
|
===============================================================================
*A:PE#
Label |
Description |
---|---|
AdminRate |
Displays the configured aggregate rate in the subscriber profile. |
OperRate |
Displays the actual downstream rate. |
Limit Unused Bandwidth |
Indicates whether the limit-unused-bandwidth command is enabled to protect against exceeding the aggregated bandwidth |
OnTheWireRates |
Indicates whether the displayed rates are on-the-wire rates. |
LastMileOnTheWireRates |
Indicates whether the displayed rates are on-the-wire rates for the last mile only. |
sap
Syntax
sap sap-id [scheduler scheduler-name] [{ingress | egress}]
Context
[Tree] (clear>qos>scheduler-stats sap)
Full Context
clear qos scheduler-stats sap
Description
This command clears scheduler statistics.
Parameters
- sap-id
-
Specifies the SAP assigned to the service.
- scheduler-name
-
Displays the scheduler name.
- ingress
-
Display only the policy displayed on the ingress SAP.
- egress
-
Display only the policy displayed on the egress SAP.
Platforms
All
sap
Syntax
sap sap-id start mode [mac-swap] [mac ieee-address] [all]
sap sap-id stop
Context
[Tree] (tools>perform>service>id>loopback>eth sap)
Full Context
tools perform service id loopback eth sap
Description
This command places and removes the specific SAP in loopback mode for reflecting Ethernet traffic back in the direction of the received stream. This is only applicable to Ethernet-based SAPs.
Parameters
- sap-id
-
Specifies the SAP ID.
- start
-
Keyword that places the sap in loopback mode.
- mode
-
Keywords that specify the location on the loopback in relation to the SAP.
- stop
-
Removes the SAP from loopback mode.
- mac-swap
-
Enable source address and destination address swapping for the reflected packets when the arriving packet is unicast. Any broadcast and multicast packets arriving on a looped point will be dropped.
- mac ieee-address
-
Optionally configures the source MAC address used in the reflected packet when the arriving packet is a broadcast or multicast. This does not apply to arriving unicast packets.
6-byte unicast mac-address in the form xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx.
- all
-
Configured ieee-address is used as the source address for all reflected packets regardless of the arriving destination.
Platforms
All
sap
Syntax
sap sap-id [arbiter {root | name}] [ingress | egress] [interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor>qos>arbiter-stats sap)
Full Context
monitor qos arbiter-stats sap
Description
This command monitors arbiter statistics for a SAP.
Parameters
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- name
-
Specifies the name of the policer control policy arbiter, up to 32 characters. This parameter is mandatory if the SAP resides on a LAG in adapt-qoslink or port-fair mode.
- root
-
Specifies the arbiter to which this queue would be feeding.
- ingress
-
Displays scheduler-name statistics applied on the ingress SAP.
- egress
-
Displays scheduler-name statistics applied on the egress SAP.
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures the number of times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
sap
Syntax
sap sap-id [scheduler scheduler-name] [ ingress | egress] [interval seconds] [ repeat repeat] [absolute | rate]
Context
[Tree] (monitor>qos>scheduler-stats sap)
Full Context
monitor qos scheduler-stats sap
Description
Use this command to monitor scheduler statistics for a SAP at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the specified SAP. The subsequent statistical information listed for each interval is displayed as a delta to the previous display.
When the keyword rate is specified, the rate-per-second for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor commands display the selected statistics according to the configured number of times at the interval specified.
Parameters
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- scheduler-name
-
Specifies an existing scheduler-name, up to 32 characters. Scheduler names are configured in the config>qos>scheduler-policy>tier level context. This parameter is mandatory if the SAP resides on a LAG in adapt-qoslink or port-fair mode.
- ingress
-
Displays scheduler-name statistics applied on the ingress SAP.
- egress
-
Displays scheduler-name statistics applied on the egress SAP.
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
All
sap
Syntax
sap sap-id [interval seconds] [repeat repeat] [absolute | rate]
sap sap-id encap-group group-name [member encap-id] [interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor>service>id sap)
Full Context
monitor service id sap
Description
This command monitors statistics for a SAP associated with this service.
This command displays statistics for a specific SAP, identified by the port-id and encapsulation value, at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the SAP. The subsequent statistical information listed for each interval is displayed as a delta to the previous display. When the keyword rate is specified, the rate-per-second for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor commands display the selected statistics according to the configured number of times at the interval specified.
Parameters
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- port-id
-
Specifies the physical port ID in the slot/mda/port, esat-id/slot/ port or pxc-id.sub-port format.
If the card in the slot has XMAs/MDAs installed, the port-id must be in the slot_number/MDA_number/port_number format. For example, 6/2/3 specifies port 3 on XMA/MDA 2 in slot 6.
The port-id must reference a valid port type. When the port-id parameter represents SONET/SDH and TDM channels, the port ID must include the channel ID. A period ".” separates the physical port from the channel-id. The port must be configured as an access port. Channels are supported on the 7750 SR.
If the SONET/SDH port is configured as clear-channel then only the port is specified.
- bundle-id
-
Specifies the multilink bundle to be associated with this IP interface. The bundle keyword must be entered at the beginning of the parameter. This parameter applies to the 7750 SR.
The command syntax must be configured as follows:
bundle-id: bundle-type-slot-id/mda-slot.bundle-num
bundle-id value range: 1 to 128
For example:
*A:ALA-12>config# port bundle-ppp-5/1.1 *A:ALA-12>config>port# multilink-bundle
- bgprp-id
-
Specifies the bundle protection group ID to be associated with this IP interface. The bpgrp keyword must be entered at the beginning of the parameter. This parameter applies to the 7750 SR.
The command syntax must be configured as follows:
bpgrp-id:
bpgrp-type-bpgrp-num
type:
ima
bpgrp-num value range:
1 to 1280
Example:
*A:ALA-12>config# port bpgrp-ima-1 *A:ALA-12>config>service>vpls$ sap bpgrp-ima-1
- qtag1, qtag2
-
Specifies the encapsulation value used to identify the SAP on the port or sub-port. If this parameter is not specifically defined, the default value is 0.
- group-name
-
Specifies the name of the encap group, up to 32 characters.
- encap-id
-
Specifies the value of the encapsulation ID to be displayed.
- seconds
-
Configures the interval for each display, in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays absolute rate-per-second value for each statistic.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
All
Output
The following output is an example of SAP information.
Output Example*A:cses-A13# monitor service id 88 sap 1/1/2:0
===============================================================================
Monitor statistics for Service 88 SAP 1/1/2:0
===============================================================================
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Sap Statistics
-------------------------------------------------------------------------------
Last Cleared Time : N/A
Packets Octets
Forwarding Engine Stats
Dropped : 0 0
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Queueing Stats(Ingress QoS Policy 1)
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Queueing Stats(Egress QoS Policy 1)
Dro. InProf : 0 0
Dro. OutProf : 0 0
For. InProf : 0 0
For. OutProf : 0 0
-------------------------------------------------------------------------------
Sap per Queue Stats
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LoPrio : 0 0
Dro. HiPrio : 0 0
Dro. LoPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
sap
Syntax
sap sap-id [arbiter {name | root}] [ingress | egress]
Context
[Tree] (clear>qos>arbiter-stats sap)
Full Context
clear qos arbiter-stats sap
Description
This command clears the arbiter statistics per SAP.
Parameters
- sap-id
-
Specifies the port ID portion of the SAP definition.
- name
-
Specifies the arbiter name, up to 32 characters.
- root
-
Specifies the arbiter root, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
sap
Syntax
sap sap-id [arbiter name | root] [ingress | egress]
Context
[Tree] (show>qos>arbiter-stats sap)
Full Context
show qos arbiter-stats sap
Description
This command displays the arbiter statistics per SAP.
Parameters
- sap-id
-
Specifies the SAP ID.
- name
-
Specifies the arbiter name, up to 32 characters.
- root
-
Specifies the arbiter root, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
sap
Syntax
sap sap-id [ingress | egress] [detail] [port port-id]
Context
[Tree] (show>qos>policer sap)
Full Context
show qos policer sap
Description
This command displays the policer per SAP.
Parameters
- sap-id
-
Specifies the SAP ID.
- port-id
-
Specifies the port ID.
Platforms
All
sap-egress
sap-egress
Syntax
sap-egress [policy-id] [association | match-criteria | detail]
sap-egress summary
Context
[Tree] (show>qos sap-egress)
Full Context
show qos sap-egress
Description
This command displays SAP egress QoS policy information.
Parameters
- policy-id
-
Displays information about the specific policy ID.
- detail
-
Displays detailed policy information including policy associations.
- summary
-
Displays SAP egress policy summary.
Platforms
All
Output
The following output is an example of QoS SAP egress information, and Show QoS SAP Egress Output Fields describes the output fields.
Output Example*A:PE# show qos sap-egress
===============================================================================
Sap Egress Policies
===============================================================================
Policy-Id Scope Name Description
-------------------------------------------------------------------------------
1 Template default Default SAP egress QoS policy.
-------------------------------------------------------------------------------
Number of Policies : 1
-------------------------------------------------------------------------------
===============================================================================
*A:PE# show qos sap-egress 1 detail
===============================================================================
QoS Sap Egress
===============================================================================
-------------------------------------------------------------------------------
Sap Egress Policy (1)
-------------------------------------------------------------------------------
Policy-id : 1 Scope : Template
Ethernet-ctag : False Parent-loc : default
Name : default
Description : Default SAP egress QoS policy.
Policy Active : True Plcrs HQoS Managed : False
Post Plcr Mapping Policy: (Not Specified)
HS Attachment Policy : default
-------------------------------------------------------------------------------
Dynamic Configuration Information
-------------------------------------------------------------------------------
PccRule Insert Point : n/a DynPlcr Insert Point : n/a
CBS : Def MBS : Def
Parent : (Not Specified)
Level : 1 Weight : 1
Packet Byte Offset : 0
Stat Mode : minimal
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Queue Information
-------------------------------------------------------------------------------
Queue-Id : 1 Queue-Type : auto-expedite
Admin PIR : max Admin CIR : 0
PIR Percent : def CIR Percent : def
PIR Rule : closest CIR Rule : closest
CBS : Def MBS : Def
Avg Frame Overhead : 0.00 Packet Byte Offset : add 0
Adv Config Policy : (Not Specified)
Parent : (Not Specified)
PIR Level/Weight : 1/1 CIR Level/Weight : 0/1
Burst Limit : default
Wred Queue Mode : none Wred Queue SlopeUsage: not-applicable
Slope Policy : default
High-Plus Drop Tail : def High Drop Tail : def
Low Drop Tail : def Exceed Drop Tail : def
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
HS Queue Information
-------------------------------------------------------------------------------
Queue-Id : 1
Admin PIR : max
PIR Percent : def
PIR Rule : closest
MBS : Def
Packet Byte Offset : add 0
Burst Limit : default
HS Class Weight : 1 HS Wrr Weight : 1
HS Wred-Q Slope Plcy : _tmnx_hs_default
HS Alt Class Pool : False
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
HS Wrr Group Information
-------------------------------------------------------------------------------
HS Wrr Group Id : 1 Class Weight : 1
Rate : max Percent Rate : 100.00
PIR Adaptation Rule: closest
HS Wrr Group Id : 2 Class Weight : 1
Rate : max Percent Rate : 100.00
PIR Adaptation Rule: closest
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Forwarding Class (FC) Classification and Remarking Information
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
FC Queue Queue-Group InstanceId SapBReDir Plcr
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
Associations
-------------------------------------------------------------------------------
Service-Name : 1
Service-Id : 1 (VPLS) Customer-Id : 1
- SAP : 2/1/1
- SAP : 5/1/1
-------------------------------------------------------------------------------
Mirror SAPs
-------------------------------------------------------------------------------
No Mirror SAPs Found.
-------------------------------------------------------------------------------
DSCP Cntr Id Profile fc
-------------------------------------------------------------------------------
No DSCP-Map Entries Found.
-------------------------------------------------------------------------------
Prec Value Cntr Id Profile fc
-------------------------------------------------------------------------------
No Prec-Map Entries Found.
-------------------------------------------------------------------------------
Dot1p fc Profile
-------------------------------------------------------------------------------
No Dot1p-Map Entries Found.
-------------------------------------------------------------------------------
Match Criteria
-------------------------------------------------------------------------------
No Matching Criteria.
*A:PE#
Label |
Description |
---|---|
Policy-Id |
The ID that uniquely identifies the policy. |
Scope |
Exclusive — Specifies that this policy can only be applied to a single SAP. Template — Specifies that this policy can be applied to multiple SAPs on the router. |
Description |
A text string that helps identify the policy context in the configuration file. |
Queue |
|
CIR Admin |
Specifies the administrative Committed Information Rate (CIR) parameters for the queue. The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. |
CIR Oper |
The operational value derived by computing the CIR value from the administrative CIR and PIR values and their corresponding adaptation rules. |
CIR Rule |
min — The operational CIR for the queue will be equal to or greater than the administrative rate specified using the rate command except where the derived operational CIR is greater than the operational PIR. If the derived operational CIR is greater than the derived operational PIR, the operational CIR will be made equal to the operational PIR. max — The operational CIR for the queue will be equal to or less than the administrative rate specified using the rate command. closest — The operational CIR for the queue will be the rate closest to the rate specified using the rate command without exceeding the operational CIR. |
PIR Admin |
Specifies the administrative Peak Information Rate (PIR) parameters for the queue. The PIR defines the maximum rate that the queue can transmit packets through the switch fabric (for SAP ingress queues) or out an egress interface (for SAP egress queues). |
PIR Oper |
The administrative PIR specified by the user. |
PIR Rule |
min — The operational PIR for the queue will be equal to or greater than the administrative rate specified using the rate command. max — The operational PIR for the queue will be equal to or less than the administrative rate specified using the rate command. closest — The operational PIR for the queue will be the rate closest to the rate specified using the rate command. |
CBS |
def — Specifies that the CBS value reserved for the queue. value — Specifies the value to override the default reserved buffers for the queue. |
MBS |
def — Specifies that the MBS value is set by the def-mbs function. value — Specifies the value to override the default maximum size for the queue. |
HiPrio |
Specifies the percentage of buffer space for the queue, used exclusively by high-priority packets. |
PIR Lvl/Wt |
Specifies the priority level of the scheduler when compared to other child schedulers and queues vying for bandwidth on the parent schedulers during the above-CIR distribution phase of bandwidth allocation. Weight defines the relative weight of this scheduler in comparison to other child schedulers and queues at the same level. |
CIR Lvl/Wt |
Specifies the level of hierarchy when compared to other schedulers and queues when vying for bandwidth on the parent scheduler. Weight defines the relative weight of this queue in comparison to other child schedulers and queues while vying for bandwidth on the parent scheduler. |
Parent |
Specifies the parent scheduler that governs the available bandwidth given the queue aside from the queue’s PIR setting. |
FC Name |
Specifies the forwarding class queue mapping or dot1p marking is to be edited. |
Queue-id |
Specifies the queue-id that uniquely identifies the queue within the policy. |
Explicit/Default |
Explicit — Specifies the egress IEEE 802.1p (dot1p) bits marking for fc-name. Default — Specifies that the default dot1p value (0) is used. |
Service Association |
|
Service-Id |
The unique service ID number that identifies the service in the service domain. |
Customer-Id |
Specifies the customer ID that identifies the customer to the service. |
SAP |
Specifies the Service Access Point (SAP) within the service where the policy is applied. |
Mirror SAPs |
|
Mirror Dest |
Specifies the mirror service ID that identifies the service in the service domain. |
SAP |
Specifies the Service Access Point (SAP) within the service where the SAP egress policy is applied. |
sap-ingress
sap-ingress
Syntax
sap-ingress [policy-id] [association | match-criteria | detail]
sap-ingress summary
Context
[Tree] (show>qos sap-ingress)
Full Context
show qos sap-ingress
Description
This command displays SAP ingress QoS policy information.
Parameters
- policy-id
-
Displays information about the specific policy ID.
- detail
-
Displays detailed policy information including policy associations.
- summary
-
Displays SAP ingress policy summary.
Platforms
All
Output
The following output is an example of QoS SAP ingress information, and Show QoS SAP Ingress Output Fields describes the output fields.
Output Example*A:PE# show qos sap-ingress
===============================================================================
Sap Ingress Policies
===============================================================================
Policy-Id Scope Name Description
-------------------------------------------------------------------------------
1 Template default Default SAP ingress QoS policy.
-------------------------------------------------------------------------------
Number of Policies : 1
-------------------------------------------------------------------------------
===============================================================================
*A:PE#
*A:PE# show qos sap-ingress 1 detail
===============================================================================
QoS Sap Ingress
===============================================================================
-------------------------------------------------------------------------------
Sap Ingress Policy (1)
-------------------------------------------------------------------------------
Policy-id : 1 Scope : Template
Default FC : be Priority : Low
Criteria-type : None
Name : default
Description : Default SAP ingress QoS policy.
Policy Active : True
-------------------------------------------------------------------------------
Dynamic Configuration Information
-------------------------------------------------------------------------------
PccRule Insert Point : n/a DynPlcr Insert Point : n/a
CBS : Def MBS : Def
Parent : (Not Specified)
Level : 1 Weight : 1
Packet Byte Offset : 0
Stat Mode : minimal
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Q Mode CIR Admin PIR Admin CBS PIR Lvl/Wt Parent
CIR Rule PIR Rule MBS CIR Lvl/Wt BurstLimit(B)
CIR Prcnt PIR Prcnt Low Drop Tail
Pkt Bt Ofst Adv Config Policy Name
FIR Admin FIR Rule Cir-non-profiling
FIR Prcnt
-------------------------------------------------------------------------------
1 Prio 0 max def 1/1 None
closest closest def 0/1 default
def def def
(not-assigned) add 0 (not-assigned)
0 closest disabled
def
11 Prio 0 max def 1/1 None
closest closest def 0/1 default
def def def
(not-assigned) add 0 (not-assigned)
0 closest disabled
def
===============================================================================
Sap-Ingress FC (Detail)
===============================================================================
No FC-Map Entries Found.
===============================================================================
-------------------------------------------------------------------------------
FC DE-1-out-profile Profile In-Remark Out-Remark Egr-Override-FC
-------------------------------------------------------------------------------
No SubFC Map Entries Found.
-------------------------------------------------------------------------------
Dot1p FC Priority
-------------------------------------------------------------------------------
No Dot1p-Map Entries Found.
-------------------------------------------------------------------------------
DSCP FC Priority
-------------------------------------------------------------------------------
No DSCP-Map Entries Found.
-------------------------------------------------------------------------------
Prec Value FC Priority
-------------------------------------------------------------------------------
No Prec-Map Entries Found.
-------------------------------------------------------------------------------
Match Criteria
-------------------------------------------------------------------------------
No Matching Criteria.
-------------------------------------------------------------------------------
Associations
-------------------------------------------------------------------------------
Service-Name : 1
Service-Id : 1 (VPLS) Customer-Id : 1
- SAP : 2/1/1
- SAP : 5/1/1
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
LSP EXP FC Priority
-------------------------------------------------------------------------------
No LspExp-Map Entries Found.
===============================================================================
*A:PE#
Label |
Description |
---|---|
Policy-Id |
The ID that uniquely identifies the policy. |
Scope |
Exclusive — Specifies that this policy can only be applied to a single SAP. Template - Specifies that this policy can be applied to multiple SAPs on the router. |
Description |
A text string that helps identify the policy context in the configuration file. |
Default FC |
Specifies the default forwarding class for the policy. |
Priority |
Specifies the enqueuing priority when a packet is marked with a dot1p-value specified. |
Criteria-type |
IP — Specifies that an IP criteria-based SAP ingress policy is used to select the appropriate ingress queue and corresponding forwarding class for matched traffic. MAC — Specifies that a MAC criteria-based SAP is used to select the appropriate ingress queue and corresponding forwarding class for matched traffic. |
Mode |
Specifies the configured mode of the meter (trTcm or srTcm). |
CIR Admin |
Specifies the administrative Committed Information Rate (CIR) parameters for the queue. The CIR defines the rate at which the system prioritizes the queue over other queues competing for the same bandwidth. |
CIR Oper |
The operational value derived by computing the CIR value from the administrative CIR and PIR values and their corresponding adaptation rules. |
CIR Rule |
min — The operational CIR for the queue will be equal to or greater than the administrative rate specified using the rate command. max — The operational CIR for the queue will be equal to or less than the administrative rate specified using the rate command. closest —The operational CIR for the queue will be the rate closest to the rate specified using the rate command without exceeding the operational CIR. |
PIR Admin |
Specifies the administrative Peak Information Rate (PIR) parameters for the queue. The PIR defines the maximum rate that the queue can transmit packets through the switch fabric (for SAP ingress queues) or out an egress interface (for SAP egress queues). |
PIR Oper |
The administrative PIR specified by the user. |
PIR Rule |
min — The operational PIR for the queue will be equal to or greater than the administrative rate specified using the rate command. max — The operational PIR for the queue will be equal to or less than the administrative rate specified using the rate command. closest — The operational PIR for the queue will be the rate closest to the rate specified using the rate command. |
CBS |
def — Specifies the default CBS value for the queue. value — Specifies the value to override the default reserved buffers for the queue. |
MBS |
def — Specifies the default MBS value. value — Specifies the value to override the default MBS for the queue. |
HiPrio |
Specifies the percentage of buffer space for the queue, used exclusively by high-priority packets. |
PIR Lvl/Wt |
Specifies the priority level of the scheduler when compared to other child schedulers and queue vying for bandwidth on the parent schedulers during the above-CIR distribution phase of bandwidth allocation. Weight defines the relative weight of this scheduler in comparison to other child schedulers and queue at the same level. |
CIR Lvl/Wt |
Specifies the level of hierarchy when compared to other schedulers and queue when vying for bandwidth on the parent scheduler. Weight defines the relative weight of this queue in comparison to other child schedulers and queue while vying for bandwidth on the parent scheduler. |
Parent |
Specifies the parent scheduler that governs the available bandwidth given the queue, aside from the queue’s PIR setting. |
Dot1p |
Specifies the forwarding class or enqueuing priority when a packet is marked with a dot1p-value specified. |
FC |
Specifies the forwarding class overrides. |
Priority |
The optional priority setting overrides the default enqueuing priority for the packets received on an ingress SAP that uses the policy that matches this rule. High — Specifies that the high enqueuing parameter for a packet increases the likelihood of enqueuing the packet when the ingress queue is congested. Low —Specifies that the low enqueuing parameter for a packet decreases the likelihood of enqueuing the packet when the ingress queue is congested. |
DSCP |
Specifies the forwarding class or enqueuing priority when a packet is marked with the DiffServ Code Point (DSCP) value. |
FC |
Specifies one of the predefined forwarding classes in the system. When a packet matches the rule, the forwarding class is only overridden when the fc fc-name parameter is defined on the rule. |
Priority |
This parameter specifies the default enqueuing priority overrides for all packets received on an ingress SAP using this policy that matches this rule. High — Specifies that the high enqueuing parameter for a packet increases the likelihood of enqueuing the packet when the ingress queue is congested. Low — Specifies that the low enqueuing parameter for a packet decreases the likelihood of enqueuing the packet when the ingress queue is congested. |
Prec |
Specifies the forwarding class or enqueuing priority when a packet is marked with an IP precedence value ( ip-prec-value). |
UCastQ |
Specifies the default unicast forwarding type queue mapping. |
MCastQ |
Specifies the overrides for the default multicast forwarding type queue mapping. |
BCastQ |
Specifies the default broadcast forwarding type queue mapping. |
UnknownQ |
Specifies the default unknown unicast forwarding type queue mapping. |
Match Criteria |
Specifies an IP or MAC criteria entry for the policy. |
Entry |
|
Source IP |
Specifies a source IP address range used for an ingress SAP QoS policy match. |
Source Port |
Specifies a source TCP or UDP port number or port range used for an ingress SAP QoS policy match. |
Protocol |
Specifies the IP protocol number to be used for an ingress SAP QoS policy match. |
DSCP |
Specifies a DiffServ Code Point (DSCP) name used for an ingress SAP QoS policy match. |
Fragment |
True — Configures a match on all fragmented IP packets. False — Configures a match on all non-fragmented IP packets. |
FC |
Specifies the entry’s forwarding class. |
Priority |
Specifies the default enqueuing priority overrides for all packets received on an ingress SAP using this policy. |
Src MAC |
Specifies a source MAC address or range to be used as a Service Ingress QoS policy match. |
Dst MAC |
Specifies a destination MAC address or range to be used as a Service Ingress QoS policy match. |
Dot1p |
Specifies a IEEE 802.1p value to be used as the match. |
Snap-pid |
Specifies an IEEE 802.3 LLC SNAP Ethernet Frame PID value to be used as a Service Ingress QoS policy match. |
Ethernet-type |
Specifies an Ethernet type II Ethertype value to be used as a Service Ingress QoS policy match. |
ESnap-oui-zero |
Specifies an IEEE 802.3 LLC SNAP Ethernet Frame OUI zero or non-zero value to be used as a Service Ingress QoS policy match. |
DSAP |
Specifies an Ethernet 802.2 LLC DSAP value or range for an ingress SAP QoS policy match. |
SSAP |
Specifies an Ethernet 802.2 LLC DSAP value or range for an ingress SAP QoS policy match. |
FC |
Specifies the entry’s forwarding class. |
Priority |
Specifies the default enqueuing priority overrides for all packets received on an ingress SAP using this policy. |
Service Association |
|
Service-Id |
The unique service ID number that identifies the service in the service domain. |
Customer-Id |
Specifies the customer ID that identifies the customer to the service. |
SAP |
Specifies the Service Access Point (SAP) within the service where the SAP ingress policy is applied. |
sap-template
sap-template
Syntax
sap-template template-name idle-saps
Context
[Tree] (clear>subscr-mgmt sap-template)
Full Context
clear subscriber-mgmt sap-template
Description
This command deletes any SAPs created with the specified SAP template that are no longer in use by any subscriber sessions.
Parameters
- template-name
-
Specifies the name of a template, up to 256 characters, configured under configure subscriber-mgmt sap-template.
- idle-saps
-
Keyword that specifies to delete any idle SAPs associated with this template.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
sap-using
sap-using
Syntax
sap-using [ingress | egress]
Context
[Tree] (show>service sap-using)
Full Context
show service sap-using
Description
Displays SAP information.
If no optional parameters are specified, the command displays a summary of all defined SAPs.
The optional parameters restrict output to only SAPs matching the specified properties.
Parameters
- ingress
-
Specifies matching an ingress policy.
- egress
-
Specifies matching an egress policy.
- qos-policy qos-policy-id
-
The ingress or egress QoS Policy ID for which to display matching SAPs.
- filter filter-id
-
The ingress or egress Filter Policy ID for which to display matching SAPs.
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- interface
-
Specifies matching SAPs with the specified IP interface.
- ip-addr
-
The IP address of the interface for which to display matching SAPs.
- ip-int-name
-
The IP interface name for which to display matching SAPs.
Platforms
All
Output
The following output is an example of service SAP information, and SAP Output Fields describes show service SAP output fields.
Output ExampleA:ALA-48>config>service>ies# show service sap-using sap 1/3/2:244/1
===============================================================================
Service Access Points Using Port 1/3/2:15990785
===============================================================================
PortId SvcId I.QoS I.Fltr E.QoS E.Fltr A.Pol Adm Opr
-------------------------------------------------------------------------------
1/3/2:244/1 89 1 none 1 none none Up Down
-------------------------------------------------------------------------------
Number of SAPs : 1
-------------------------------------------------------------------------------
===============================================================================
A:ALA-48>config>service>ies#
Label |
Description |
---|---|
Port ID |
The ID of the access port where the SAP is defined |
Svc ID |
The service identifier |
SapMTU |
The SAP MTU value |
I.QoS |
The SAP ingress QoS policy number specified on the ingress SAP |
I.MAC/IP |
The MAC or IP filter policy ID applied to the ingress SAP |
E.QoS |
The SAP egress QoS policy number specified on the egress SAP |
E.Mac/IP |
The MAC or IP filter policy ID applied to the egress SAP |
A.Pol |
The accounting policy ID assigned to the SAP |
Adm |
The desired state of the SAP |
Opr |
The actual state of the SAP |
sap-using
Syntax
sap-using [msap] [dyn-script] [description]
sap-using [sap sap-id] [vlan-translation | anti-spoof] [description]
sap-using {ingress | egress} atm-td-profile td-profile-id
sap-using {ingress | egress} filter any-filter-id
sap-using {ingress | egress} qos-policy qos-policy-id [msap]
sap-using etree
sap-using eth-cfm squelch-ingress-levels [all | ctag-space] [sap sap-id]
Context
[Tree] (show>service sap-using)
Full Context
show service sap-using
Description
This command displays SAP information.
If no optional parameters are specified, the command displays a summary of all defined SAPs.
The optional parameters restrict output to only SAPs matching the specified properties.
Parameters
- ingress
-
Specifies matching an ingress policy.
- egress
-
Specifies matching an egress policy.
- qos-policy-id
-
The ingress or egress QoS Policy ID for which to display matching SAPs.
- td-profile-id
-
Displays SAPs using this traffic description for the 7750 SR only.
- filter-id
-
The ingress or egress filter policy ID for which to display matching SAPs.
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- dyn-script
-
Displays dynamic service SAPs information.
- msap
-
Displays MSAPs.
- vlan-translation
-
Displays VLAN translation information.
- anti-spoof
-
Displays anti-spoof information.
- squelch-ingress-level
-
Displays ETH-CFM squelching information of the type matching the service delimited configuration.
- all
-
Displays all squelch ingress levels information regardless of type.
- ctag-space
-
Displays all squelch-ingress-levels information that is skipping additional VLAN space.
Platforms
All
Output
The following output is an example of sap-using using information, and Show Service SAP Output Fields describes the output fields.
Output Example*A:Dut-A# show service sap-using
========================================================================
Service Access Points
===============================================================================
PortId SvcId Ing. Ing. Egr. Egr. Adm Opr
QoS Fltr QoS Fltr
------------------------------------------------------------------------
1/1/1:1 1 1 none 1 none Up Up
2/1/2:10/11 1 1 none 1 none Up Up
2/1/2:10/12 1 1 none 1 none Up Up
2/1/2:20/11 1 1 none 1 none Up Up
2/1/2:20/12 1 1 none 1 none Up Up
2/1/4:cp.10 10 1 none 1 none Up Up
2/1/4:cp.20 20 1 none 1 none Up Up
------------------------------------------------------------------------
Number of SAPs : 7
------------------------------------------------------------------------
========================================================================
The following output is an example of SAP information for a specific SAP for the 7450 ESS or 7750 SR.
A:ALA-42#
*A:ALA-48# show service sap-using sap 1/1/21:0
===============================================================================
Service Access Points Using Port 1/1/21:0
===============================================================================
PortId SvcId Ing. Ing. Egr. Egr. Anti Adm Opr
QoS Fltr QoS Fltr Spoof
-------------------------------------------------------------------------------
1/1/21:0 1 1 none 1 none none Up Down
-------------------------------------------------------------------------------
Number of SAPs : 1
===============================================================================
*A:ALA-48#
The following output is an example of SAP information for the egress traffic policy for the 7750 SR.
*A:ALA-12# show service sap-using egress atm-td-profile 2
==============================================================================
Service Access Point Using ATM Traffic Profile 2
===============================================================================
PortId SvcId I.QoS I.Fltr E.QoS E.Fltr A.Pol Adm Opr
-------------------------------------------------------------------------------
5/1/1:0/11 511111 2 none 2 none none Up Up
5/1/1:0/12 511112 2 none 2 none none Up Up
5/1/1:0/13 511113 2 none 2 none none Up Up
5/1/1:0/14 511114 2none 2 none none Up Up
5/1/1:0/15 511115 2 none 2 none none Up Up
5/1/1:0/16 511116 2 none 2 none none Up Up
5/1/1:0/17 511117 2 none 2 none none Up Up
5/1/1:0/18 511118 2 none 2 none none Up Up
5/1/1:0/19 511119 2 none 2 none none Up Up
5/1/1:0/20 511120 2 none 2 none none Up Up
5/1/1:0/21 511121 2 none 2 none none Up Up
5/1/1:0/22 511122 2 none 2 none none Up Up
5/1/1:0/23 511123 2 none 2 none none Up Up
5/1/1:0/24 511124 2 none 2 none none Up Up
5/1/1:0/25 511125 2 none 2 none none Up Up
...
===============================================================================
*A:ALA-12#
The following output is an example of squelch ingress levels information.
show service sap-using eth-cfm squelch-ingress-levels
===============================================================================
ETH-CFM Squelching
===============================================================================
SapId SvcId Squelch Level
-------------------------------------------------------------------------------
1/1/9:2.* 2 0 1 2
1/1/9:3.* 3 0 1 2 3 4
-------------------------------------------------------------------------------
Number of SAPs: 2
===============================================================================
show service sap-using eth-cfm squelch-ingress-levels ctag-space
===============================================================================
ETH-CFM Squelching CTAG Space
===============================================================================
SapId SvcId Squelch Level
-------------------------------------------------------------------------------
1/1/9:3.* 3 0 1 2 3
-------------------------------------------------------------------------------
Number of SAPs: 1
===============================================================================
show service sap-using eth-cfm squelch-ingress-levels all
===============================================================================
ETH-CFM Squelching
===============================================================================
SapId SvcId Squelch Level
-------------------------------------------------------------------------------
1/1/9:2.* 2 0 1 2
1/1/9:3.* 3 0 1 2 3 4
-------------------------------------------------------------------------------
Number of SAPs: 2
===============================================================================
===============================================================================
ETH-CFM Squelching CTAG Space
===============================================================================
SapId SvcId Squelch Level
-------------------------------------------------------------------------------
1/1/9:3.* 3 0 1 2 3
-------------------------------------------------------------------------------
Number of SAPs: 1
===============================================================================
show service sap-using eth-cfm squelch-ingress-levels sap 1/1/9:3.*
===============================================================================
ETH-CFM Squelching
===============================================================================
SapId SvcId Squelch Level
-------------------------------------------------------------------------------
1/1/9:3.* 3 0 1 2 3 4
-------------------------------------------------------------------------------
Number of SAPs: 1
===============================================================================
Label |
Description |
---|---|
Port ID |
The ID of the access port where the SAP is defined |
Svc ID |
The service identifier |
Sap MTU |
The SAP MTU value |
Ing. QoS |
The SAP ingress QoS policy number specified on the ingress SAP |
Ing Fltr |
The MAC or IP filter policy ID applied to the ingress SAP |
Egr. QoS |
The SAP egress QoS policy number specified on the egress SAP for the 7450 ESS and 7750 SR only |
Egr. Fltr |
The MAC or IP filter policy ID applied to the egress SAP |
Adm |
The administrative state of the SAP |
Opr |
The operational state of the SAP |
SapId |
The ID that displays SAPs for the service |
Squelch Level |
The CFM levels configured for silent discard |
sap-using
Syntax
sap-using [ingress | egress] atm-td-profile td-profile-id
Context
[Tree] (show>service sap-using)
Full Context
show service sap-using
Description
Displays atm-td-profile SAP information.
If no optional parameters are specified, the command displays a summary of all defined SAPs.
The optional parameters restrict output to only SAPs matching the specified properties.
Parameters
- ingress
-
Specifies matching an ingress policy.
- egress
-
Specifies matching an egress policy.
- qos-policy qos-policy-id
-
The ingress or egress QoS Policy ID for which to display matching SAPs.
- filter filter-id
-
The ingress or egress Filter Policy ID for which to display matching SAPs.
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- interface
-
Specifies matching SAPs with the specified IP interface.
- ip-addr
-
The IP address of the interface for which to display matching SAPs.
- ip-int-name
-
The IP interface name for which to display matching SAPs.
- td-profile-id
-
Profile ID that identifies a specific profile to display.
Platforms
All
Output
The following output is an example of service SAP information, and SAP Output Fields describes show service SAP output fields.
Output ExampleA:ALA-48>config>service>ies# show service sap-using sap 1/3/2:244/1
===============================================================================
Service Access Points Using Port 1/3/2:15990785
===============================================================================
PortId SvcId I.QoS I.Fltr E.QoS E.Fltr A.Pol Adm Opr
-------------------------------------------------------------------------------
1/3/2:244/1 89 1 none 1 none none Up Down
-------------------------------------------------------------------------------
Number of SAPs : 1
-------------------------------------------------------------------------------
===============================================================================
A:ALA-48>config>service>ies#
Label |
Description |
---|---|
Port ID |
The ID of the access port where the SAP is defined. |
Svc ID |
The service identifier. |
SapMTU |
The SAP MTU value. |
I.QoS |
The SAP ingress QoS policy number specified on the ingress SAP. |
I.MAC/IP |
The MAC or IP filter policy ID applied to the ingress SAP. |
E.QoS |
The SAP egress QoS policy number specified on the egress SAP. |
E.Mac/IP |
The MAC or IP filter policy ID applied to the egress SAP. |
A.Pol |
The accounting policy ID assigned to the SAP. |
Adm |
The desired state of the SAP. |
Opr |
The actual state of the SAP. |
sap-using aarp
sap-using aarp
Syntax
sap-using aarp aarp-id
Context
[Tree] (show>service sap-using aarp)
Full Context
show service sap-using aarp
Description
This command displays SAP information for a specific AARP ID.
Parameters
- aarp-id
-
Specifies the AARP ID.
Platforms
All
sap-using app-profile
sap-using app-profile
Syntax
sap-using app-profile app-profile-name
Context
[Tree] (show>service sap-using app-profile)
Full Context
show service sap-using app-profile
Description
This command displays information about SAPs using the specified application profile.
Parameters
- app-profile-name
-
Specifies an existing application profile name created in the config>app-assure>group>policy context.
Platforms
All
Output
The following output is an example of the sap-using app profile command information.
Output Example*A:ALA-48# show service sap-using app-profile test
===============================================================================
Service Access Point Using Application Profile 'test'
===============================================================================
PortId SvcId Ing. Ing. Egr. Egr. Adm Opr
QoS Fltr QoS Fltr
-------------------------------------------------------------------------------
1/1/18:0 89 1 none 1 none Up Down
-------------------------------------------------------------------------------
Number of SAPs : 1
-------------------------------------------------------------------------------
===============================================================================
*A:ALA-48#
sap-using transit-policy
sap-using transit-policy
Syntax
sap-using transit-policy ip transit-ip-policy
sap-using transit-policy prefix transit-prefix-policy
Context
[Tree] (show>service sap-using transit-policy)
Full Context
show service sap-using transit-policy
Description
This command displays SAP information for a specific transit IP policy or transit prefix policy.
Parameters
- transit-ip-policy
-
Specifies the transit IP policy ID.
- transit-prefix-policy
-
Specifies a transit prefix policy ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
saps
saps
Syntax
saps [control-session acct-session-id] [ port port-id] [dynsvc-policy policy-name] [ summary] [sap sap-id] [svc-id service-id]
Context
[Tree] (show>service>dynsvc saps)
Full Context
show service dynamic-services saps
Description
This command displays Dynamic Services SAPs (instances) details.
This command is not available in the MD-CLI.
Parameters
- summary
-
Displays a summary view only.
- acct-session-id
-
Specifies control session accounting session id.
- port-id
-
Specifies Ethernet port.
- policy-name
-
Specifies dynamic services policy.
- sap sap-id
-
Specifies dynamic services SAP id.
- service-id
-
The service ID of the dynamic service.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of dynamic service SAP information.
Output Example# show service dynamic-services saps
===============================================================================
Dynamic Services SAP's
===============================================================================
SAP : 1/1/1:1.901
-------------------------------------------------------------------------------
Acct session-ID : 242FFF000001AE512CE4B6
Acct session-ID control : 242FFF000001AB512CE4B6
Service : [100000]
Dynamic Services policy : dynsvc-policy-1
Number of scripts executed : 1
Number of scripts w success : 1
Last script action : setup
Time of last script action : 2013/02/26 16:37:10
Parameters of last action : vprn_1={'t':('VRF-1',65000,1000,'cpe-int-1','192.
: 168.20.1/24','2001:db8:cafe::1/64',901,901,910,92
: 0,'192.168.20.0/24','192.168.20.2')}
Accounting instance 1
Status : enabled
Stats type : volume-time
Update interval (minutes) : 30
Accounting instance 2
Status : enabled
Stats type : time
Update interval (minutes) : 0
-------------------------------------------------------------------------------
No. of SAP's: 1
===============================================================================
# show service dynamic-services saps summary
===============================================================================
Dynamic Services SAP's summary
===============================================================================
SAP Acct-Session-ID Acct-Session-ID-Ctrl
-------------------------------------------------------------------------------
1/1/1:1.901 242FFF000001AE512CE4B6 242FFF000001AB512CE4B6
-------------------------------------------------------------------------------
No. of SAP's: 1
===============================================================================
Dynamic Services SAP Field Descriptions describes Dynamic Services SAP fields.
Output field |
Description |
---|---|
SAP |
The dynamic service SAP ID. |
Acct session-ID |
The dynamic service accounting session ID. |
Acct session-ID control |
The control channel accounting session ID. |
Service |
The dynamic service ID. |
Dynamic Services policy |
The policy referenced to setup the dynamic service. |
Number of scripts executed |
The number of times the script was executed for this dynamic service (setup, modify, revert or teardown). |
Number of scripts w success |
The number of times the script was executed successfully for this dynamic service. |
Last script action |
The setup, modify, revert, teardown. |
Time of last script action |
The timestamp of the last script action. |
Parameters of last action |
The content of the Dynamic Services Script Parameters attribute corresponding with the last action. |
Status |
RADIUS accounting is enabled or disabled. |
Stats type |
The type of statistics reported in accounting. |
Update interval (minutes) |
The time, in minutes, between Accounting Interim Update messages. |
satellite
satellite
Syntax
satellite
Context
[Tree] (clear>system satellite)
Full Context
clear system satellite
Description
Commands in this context clear satellite information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
satellite
Syntax
satellite
Context
[Tree] (show>system satellite)
Full Context
show system satellite
Description
This command displays a list of configured satellites including information about the satellite’s esat-ID or tsat-ID, satellite type, and state.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of satellite information.
Output ExampleA:Dut-A# show system satellite
===============================================================================
Satellite Information
===============================================================================
SatID Provisioned Type Admin Oper
Equipped Type (if different) State State
-------------------------------------------------------------------------------
esat-1 es48-1gb-sfp up provisioned
(not equipped)
esat-20 es48-1gb-sfp up up
tsat-2 ts4-choc3-sfp up up
tsat-3 ts4-choc3-sfp up up
-------------------------------------------------------------------------------
No. of Satellites: 4
===============================================================================
satellite
Syntax
satellite
Context
[Tree] (tools>perform satellite)
Full Context
tools perform satellite
Description
Commands in this context perform satellite operations.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
schedule
schedule
Syntax
schedule [schedule-name] [owner owner-name]
Context
[Tree] (show>system>cron schedule)
Full Context
show system cron schedule
Description
This command displays cron schedule parameters.
Parameters
- schedule-name
-
Specifies the scheduler name, up to 32 characters.
- owner-name
-
Specifies the scheduler owner name, up to 32 characters.
Platforms
All
Output
The following output is an example of cron schedule information. The following table describes the output fields.
Output ExampleA:sim1>show>cron schedule test
===============================================================================
CRON Schedule Information
===============================================================================
Schedule : test
Schedule owner : TiMOS CLI
Description : none
Administrative status : enabled
Operational status : enabled
Action : test
Action owner : TiMOS CLI
Script : test
Script Owner : TiMOS CLI
Script source location : ftp://*****:******@192.168.15.1/home/testlab_bgp
/cron/test1.cfg
Script results location : ftp://*****:******@192.168.15.1/home/testlab_bgp
/cron/res
Schedule type : periodic
Interval : 0d 00:01:00 (60 seconds)
Next scheduled run : 0d 00:00:42
Weekday : tuesday
Month : none
Day of month : none
Hour : none
Minute : none
Number of schedule runs : 10
Last schedule run : 2008/01/01 17:20:52
Number of schedule failures : 0
Last schedule failure : no error
Last failure time : never
===============================================================================
A:sim1>show>cron
Label |
Description |
---|---|
Schedule |
Displays the schedule name. |
Schedule owner |
Displays the owner name of the action. |
Description |
Displays the schedule’s description. |
Administrative status |
Enabled — The administrative status is enabled. Disabled — Administratively disabled. |
Operational status |
Enabled — The operational status is enabled. Disabled — Operationally disabled. |
Action |
Displays the action name. |
Action owner |
Displays the name of action owner. |
Script |
Displays the name of the script. |
Script owner |
Displays the name of the script. |
Script owner |
Displays the name of the of script owner. |
Script source location |
Displays the location of scheduled script. |
Script results location |
Displays the location where the script results have been sent. |
Schedule type |
Periodic — Displays a schedule which ran at a given interval. Calendar — Displays a schedule which ran based on a calendar. Oneshot — Displays a schedule which ran one time only. |
Interval |
Displays the interval between runs of an event. |
Next scheduled run |
Displays the time for the next scheduled run. |
Weekday |
Displays the configured weekday. |
Month |
Displays the configured month. |
Day of Month |
Displays the configured day of month. |
Hour |
Displays the configured hour. |
Minute |
Displays the configured minute. |
Number of scheduled runs |
Displays the number of scheduled sessions. |
Last scheduled run |
Displays the last scheduled session. |
Number of scheduled failures |
Displays the number of scheduled sessions that failed to execute. |
Last scheduled failure |
Displays the last scheduled session that failed to execute. |
Last failure time |
Displays the system time of the last failure. |
scheduler-hierarchy
scheduler-hierarchy
Syntax
scheduler-hierarchy
Context
[Tree] (show>qos scheduler-hierarchy)
Full Context
show qos scheduler-hierarchy
Description
This command displays scheduler-hierarchy information.
Platforms
All
scheduler-name
scheduler-name
Syntax
scheduler-name scheduler-name
Context
[Tree] (show>qos scheduler-name)
Full Context
show qos scheduler-name
Description
This command displays the scheduler policies using the specified scheduler.
Parameters
- scheduler-name
-
The name of a scheduler configured in the config>qos>scheduler-policy>tier context.
Platforms
All
Output
The following output is an example of scheduler name information.
Output ExampleA:ALA-12# show qos scheduler-name NetworkControl
==================================================================
Scheduler : NetworkControl
==================================================================
Scheduler Policy : SLA1
Scheduler Policy : alpha
Scheduler Policy : beta
==================================================================
A:ALA-12#
scheduler-policy
scheduler-policy
Syntax
scheduler-policy [scheduler-policy-name] [ association | sap-ingress policy-id | sap-egress policy-id]
scheduler-policy scheduler-policy-name { ingress | egress} queue-group queue-grp-name
Context
[Tree] (show>qos scheduler-policy)
Full Context
show qos scheduler-policy
Description
Use this command to display scheduler policy information.
Parameters
- scheduler-policy-name
-
The name of a scheduler policy configured in the config>qos>scheduler-policy context.
- association
-
Displays the associations related to the specified scheduler name.
- sap-ingress policy-id
-
Specifies the SAP ingress QoS policy information.
- sap-egress policy-id
-
Specifies the SAP egress QoS policy information.
- {ingress | egress}
-
Specifies the direction to display and are mutually exclusive.
- queue-grp-name
-
Displays information for the specified queue group.
Platforms
All
Output
The following output is an example of scheduler policy information, and Show QoS Scheduler-Policy Output Fields describes the customer scheduler hierarchy fields.
Output ExampleA:ALA-12# show qos scheduler-policy SLA1
==============================================================================
QoS Scheduler Policy
==============================================================================
Policy-Name : SLA1
Description : NetworkControl(3), Voice(2) and NonVoice(1) have strict priorities
-----------------------------------------------------------------------------
Tier/Scheduler Lvl/Wt PIR Parent
CIR Lvl/Wt CIR
------------------------------------------------------------------------------
1 All_traffic 1/1 11000 None
-/- max
2 NetworkControl 3/1 100 All_traffic
3/- max
2 NonVoice 1/1 11000 All_traffic
1/- max
2 Voice 2/1 5500 All_traffic
2/- max
3 Internet_be 1/1 max NonVoice
1/- max
3 Internet_priority 2/1 max NonVoice
2/- max
3 Internet_voice 1/1 max Voice
-/- max
3 VPN_be 1/1 max NonVoice
1/- max
3 VPN_nc 1/1 100 NetworkControl
-/- 36
3 VPN_priority 2/1 max NonVoice
2/- max
3 VPN_reserved 3/1 max NonVoice
3/- max
3 VPN_video 5/1 1500 NonVoice
5/- 1500
3 VPN_voice 1/1 2500 Voice
-/- 2500
==============================================================================
A:ALA-12# show qos scheduler-policy SLA1 association
=============================================================================
QoS Scheduler Policy
=============================================================================
Policy-Name : SLA1
Description : NetworkControl(3), Voice(2) and NonVoice(1) have strict priorities
------------------------------------------------------------------------------
Associations
------------------------------------------------------------------------------
Service-Id : 6000 (Epipe) Customer-Id : 274
- SAP : 1/1/3.1:0 (Egress)
Service-Id : 7000 (VPLS) Customer-Id : 7
- SAP : 1/1/5:0 (Egress)
- Multi Service Site : west (Ingress)
==============================================================================
A:ALA-12# show qos scheduler-policy SLA1 sap-egress 101
==============================================================================
Compatibility : Scheduler Policy SLA1 & Sap Egress 101
==============================================================================
Orphan Queues :
None Found
Hierarchy :
Root
|
|---(S) : All_traffic
| |
| |---(S) : NetworkControl
| | |
| | |---(S) : VPN_nc
| |
| |---(S) : NonVoice
| | |
| | |---(S) : Internet_be
| | |
| | |---(S) : Internet_priority
| | |
| | |---(S) : VPN_be
| | |
| | |---(S) : VPN_priority
| | |
| | |---(S) : VPN_reserved
| | |
| | |---(S) : VPN_video
| |
| |---(S) : Voice
| | |
| | |---(S) : Internet_voice
| | |
| | |---(S) : VPN_voice
==============================================================================
show qos scheduler-policy "sched1" sap-ingress 100
===============================================================================
Compatibility : Scheduler Policy sched1 & Sap Ingress 100
===============================================================================
Orphan Queues :
None Found
Orphan Policers :
None Found
Hierarchy :
Root
|
|---(S) : sch1
| |
| |---(S) : sch21
| | |
| | |---(Q) : 2
| | |
| | |---(P) : 16
| |
| |---(S) : sch22
| | |
| | |---(Q) : 3
| | |
| | |---(Q) : 17
|
|---(S) : sch2
| |
| |---(S) : sch23
| | |
| | |---(Q) : 4
| | |
| | |---(Q) : 18
| |
| |---(S) : sch24
| | |
| | |---(Q) : 5
| | |
| | |---(P) : 19
|
|---(Q) : 1
|
|---(Q) : 6
|
|---(Q) : 7
|
|---(Q) : 11
|
|---(Q) : 16
|
|---(Q) : 19
|
|---(P) : 17
|
|---(P) : 18
===============================================================================
Label |
Description |
---|---|
Policy-Name |
Specifies the scheduler policy name. |
Description |
Specifies a text string that helps identify the policy context in the configuration file. |
Tier |
Specifies the level of hierarchy that a group of schedulers are associated with. |
Scheduler |
Specifies the scheduler name. |
Lvl/Wt |
Specifies the priority level of the scheduler when compared to other child schedulers and queues vying for bandwidth on the parent schedulers during the above-CIR distribution phase of bandwidth allocation. Weight defines the relative weight of this scheduler in comparison to other child schedulers and queues at the same level. |
Cir Lvl/Wt |
Specifies the level of hierarchy when compared to other schedulers and queues when vying for bandwidth on the parent scheduler. Weight defines the relative weight of this queue in comparison to other child schedulers and queues while vying for bandwidth on the parent scheduler. |
PIR |
Specifies the PIR rate. |
CIR |
Specifies the CIR rate. |
Parent |
Specifies the parent scheduler that governs the available bandwidth given the queue aside from the PIR setting of the queue. |
Service-Id |
Specifies the ID that uniquely identifies the policy. |
Customer-Id |
Specifies the ID that uniquely identifies the customer. |
SAP |
Specifies the Service Access Point (SAP) within the service where the policy is applied. |
Multi Service Site |
Specifies the multiservice site name. |
Orphan Queues |
Specifies the number of queues in an orphaned state. |
Hierarchy |
Displays the scheduler policy tree structure. |
scheduler-stats
scheduler-stats
Syntax
scheduler-stats
Context
[Tree] (clear>qos scheduler-stats)
Full Context
clear qos scheduler-stats
Description
This command clears scheduler statistics.
Platforms
All
scheduler-stats
Syntax
scheduler-stats
Context
[Tree] (show>qos scheduler-stats)
Full Context
show qos scheduler-stats
Description
This command displays scheduler statistics information.
Platforms
All
scheduler-stats
Syntax
scheduler-stats
Context
[Tree] (monitor>qos scheduler-stats)
Full Context
monitor qos scheduler-stats
Description
Commands in this context configure monitor commands for scheduler statistics.
Platforms
All
screen
screen
Syntax
screen
Context
[Tree] (clear screen)
Full Context
clear screen
Description
This command allows an operator to clear the Telnet or console screen.
Platforms
All
script
script
Syntax
script
Context
[Tree] (show>service>dynsvc script)
Full Context
show service dynamic-services script
Description
Commands in this context show dynamic services script information.
These commands are not available in the MD-CLI.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
script
Syntax
script [script-name] [owner script-owner]
Context
[Tree] (show>system>script-control script)
Full Context
show system script-control script
Description
This command displays script parameters.
Parameters
- script-name
-
Displays information for the specified script. 32 characters maximum.
- script-owner
-
Displays information for the specified script owner. 32 characters maximum.
Platforms
All
Output
The following output is an example of show script command information, and Show Script Output describes the output fields.
Output ExampleA:sim1>show>system>script-control# script
===============================================================================
Script Information
===============================================================================
Script : test
Owner name : TiMOS CLI
Description : asd
Administrative status : enabled
Operational status : enabled
Script source location : ftp://*****:******@192.168.100.1/home/testlab_bgp
/test1.cfg
Last script error : none
Last change : 2015/01/07 17:10:03
===============================================================================
A:sim1>show>cron#
Label |
Description |
---|---|
Script |
Displays the name of the script. |
Script owner |
Displays the owner name of script. |
Administrative status |
Enabled — Administrative status is enabled. Disabled — Administratively disabled. |
Operational status |
Enabled — Operational status is enabled. Disabled — Operationally disabled. |
Script source location |
Displays the location of scheduled script. |
Last script error |
Displays the system time of the last error. |
Last change |
Displays the system time of the last change. |
script-control
script-control
Syntax
script-control
Context
[Tree] (show>system script-control)
Full Context
show system script-control
Description
Commands in this context display script information.
Platforms
All
script-control
Syntax
script-control
Context
[Tree] (tools>perform>system script-control)
Full Context
tools perform system script-control
Description
This command performs script-control operations.
Platforms
All
script-control
Syntax
script-control
Context
[Tree] (clear>system script-control)
Full Context
clear system script-control
Description
Commands in this context clear script information.
Platforms
All
script-policy
script-policy
Syntax
script-policy script-policy-name [owner owner-name]
script-policy run-history [run-state]
Context
[Tree] (show>system>script-control script-policy)
Full Context
show system script-control script-policy
Description
This command displays script policy information.
Parameters
- script-policy-name
-
Displays policy information for the specified script. 32 characters maximum.
- owner-name
-
Displays information for the specified script owner. 32 characters maximum.
- run-state
-
Displays information for script policies in the specified state.
Platforms
All
Output
The following output is an example of script policy information, and Script Policy Output describes the output fields.
Output Example*A:Redundancy# show system script-control script-policy run-history terminated
===============================================================================
Script-policy Run History
===============================================================================
Script policy "test"
Owner "TiMOS CLI"
-------------------------------------------------------------------------------
Script Run #17
-------------------------------------------------------------------------------
Start time : 2006/11/06 20:30:09 End time : 2006/11/06 20:35:24
Elapsed time : 0d 00:05:15 Lifetime : 0d 00:00:00
State : terminated Run exit code : noError
Result time : 2006/11/06 20:35:24 Keep history : 0d 00:49:57
Error time : never
Results file : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-203008.
out
Run exit : Success
-------------------------------------------------------------------------------
Script Run #18
-------------------------------------------------------------------------------
Start time : 2006/11/06 20:35:24 End time : 2006/11/06 20:40:40
Elapsed time : 0d 00:05:16 Lifetime : 0d 00:00:00
State : terminated Run exit code : noError
Result time : 2006/11/06 20:40:40 Keep history : 0d 00:55:13
Error time : never
Results file : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-203523.
out
Run exit : Success
-------------------------------------------------------------------------------
*A:Redundancy#
*A:Redundancy# show system script-control script-policy run-history executing
===============================================================================
Script-policy Run History
===============================================================================
Script policy "test"
Owner "TiMOS CLI"
-------------------------------------------------------------------------------
Script Run #20
-------------------------------------------------------------------------------
Start time : 2006/11/06 20:46:00 End time : never
Elapsed time : 0d 00:00:56 Lifetime : 0d 00:59:04
State : executing Run exit code : noError
Result time : never Keep history : 0d 01:00:00
Error time : never
Results file : ftp://*:*@192.168.15.18/home/testlab_bgp/cron/_20061106-204559.
out
===============================================================================
*A:Redundancy#
*A:Redundancy# show system script-control script-policy run-history initializing
===============================================================================
Script-policy Run History
===============================================================================
Script policy "test"
Owner "TiMOS CLI"
-------------------------------------------------------------------------------
Script Run #21
-------------------------------------------------------------------------------
Start time : never End time : never
Elapsed time : 0d 00:00:00 Lifetime : 0d 01:00:00
State : initializing Run exit code : noError
Result time : never Keep history : 0d 01:00:00
Error time : never
Results file : none
-------------------------------------------------------------------------------
Script Run #22
-------------------------------------------------------------------------------
Start time : never End time : never
Elapsed time : 0d 00:00:00 Lifetime : 0d 01:00:00
State : initializing Run exit code : noError
Result time : never Keep history : 0d 01:00:00
Error time : never
Results file : none
-------------------------------------------------------------------------------
Script Run #23
-------------------------------------------------------------------------------
Start time : never End time : never
Elapsed time : 0d 00:00:00 Lifetime : 0d 01:00:00
State : initializing Run exit code : noError
Result time : never Keep history : 0d 01:00:00
Error time : never
Results file : none
===============================================================================
*A:Redundancy#
Label |
Description |
---|---|
Script policy |
Displays the name of the script policy. |
Script policy owner |
Displays the name of the script policy owner. |
Administrative status |
Enabled — Administrative status is enabled. Disabled — Administrative status is disabled. |
Script |
Displays the name of the script. |
Script owner |
Displays the name of the script owner. |
Script source location |
Displays the location of scheduled script. |
Max running allowed |
Displays the maximum number of allowed sessions. |
Max completed run histories |
Displays the maximum number of sessions previously run. |
Max lifetime allowed |
Displays the maximum amount of time the script may run. |
Completed run histories |
Displays the number of completed sessions. |
Executing run histories |
Displays the number of sessions in the process of executing. |
Initializing run histories |
Displays the number of sessions ready to run/queued but not executed. |
Max time tun history saved |
Displays the maximum amount of time to keep the results from a script run. |
Last change |
Displays the system time a change was made to the configuration. |
Script start error |
Displays the error found while executing the script. |
Max row empire time |
Reserved for SNMP. |
Last application |
Displays the last application used to execute the script. |
Last auth. user account |
Displays the last user used to execute the script. If no user is specified in "configure system cli-script authorization event-handler/cron” then the user is not specified. |
script-policy
Syntax
script-policy
Context
[Tree] (tools>perform>system>script-control script-policy)
Full Context
tools perform system script-control script-policy
Description
This command performs script-policy operations.
Platforms
All
script-policy
Syntax
script-policy
Context
[Tree] (clear>system>script-control script-policy)
Full Context
clear system script-control script-policy
Description
Commands in this context clear script policy information.
Platforms
All
scripts
scripts
Syntax
scripts
Context
[Tree] (show>log>event-handling scripts)
Full Context
show log event-handling scripts
Description
This command displays handler configuration and script run queue information.
Platforms
All
Output
The following output is an example of log event handling script information.
Output Example===============================================================================
Event Handling System - Script Policy Association
===============================================================================
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
Event Handling System - Script Association
===============================================================================
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
===============================================================================
Event Handling System - Script Launched List
===============================================================================
Run # Script owner Script name Script state
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
sctp-filter
sctp-filter
Syntax
sctp-filter sctp-filter-name
Context
[Tree] (show>app-assure>group sctp-filter)
Full Context
show application-assurance group sctp-filter
Description
This command displays Stream Control Transmission Protocol (SCTP) filter information
Parameters
- sctp-filter-name
-
Specifies an SCTP filter, up to 256 characters. When a filter is specified, all traffic is examined as described in the tmnxBsxSctpFltrTable.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
sdp
sdp
Syntax
sdp all | sdp-id:vc-id
Context
[Tree] (show>subscr-mgmt>errors sdp)
Full Context
show subscriber-mgmt errors sdp
Description
This command sorts all the subscriber errors by SDP.
Parameters
- all
-
Shows all errors beginning with the lowest SDP index.
- sdp-id:vc-id
-
Shows only the error of a specific SDP index.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
Subscriber Management SDP Error Field Descriptions describes subscriber management SDP error output fields.
Field |
Description |
---|---|
SDP |
The SDP ID associated with the error |
Time |
The time this error was reported to the subscriber management errors subsystem |
Service |
The service ID associated with the error |
MAC |
The MAC address associated with the error |
Error |
The error that occurred on the SDP |
Extra |
Extra information about the error that occurred |
sdp
Syntax
sdp [sdp-id [:vc-id]] [detail]
sdp far-end {ip-address | ipv6-address} [detail]
sdp sdp-id [vc-id] l2tpv3
sdp sdp-id [:vc-id] static-isids [range-id range-id]
sdp sdp-id [:vc-id] static-isids mfib
sdp sdp-id [:vc-id] [detail] vccv-bfd [session]
sdp sdp-id [:vc-id] mrp
Context
[Tree] (show>service>id sdp)
Full Context
show service id sdp
Description
Displays information for the SDPs associated with the service. If no optional parameters are specified, a summary of all associated SDPs is displayed.
Parameters
- sdp-id [:vc-id]
-
Displays only information for the specified SDP ID.
- detail
-
Displays detailed SDP information.
- ip-address | ipv6-address
-
Displays only SDPs matching with the specified far-end IP address. 64 characters maximum.
- l2tpv3
-
Indicates that the user wants to display l2tpv3 specific information for SDPs that are of type l2tpv3.
- static-isids
-
Specifies the I-Component service IDs created on the SDP.
- range-id
-
Displays the service using the specified I-component Service ID (ISID).
- mfib
-
Display MFIB related information. This parameter applies to the 7450 ESS or7750 SR only.
- vccv-bfd
-
Displays detailed information about the VCCV BFD session for a spoke SDP.
- session
-
displays a summary of all VCCV sessions.
- mrp
-
Displays detailed MRP information.
Platforms
All
Output
The following command displays SDP information and Show Service-ID SDP Field Descriptions describes the output fields.
show service id sdp
Output Example
===============================================================================
Services: Service Destination Points
===============================================================================
SdpId Type Far End addr Adm Opr I.Lbl E.Lbl
-------------------------------------------------------------------------------
32767:4294967294 VplsPmsi not applicable Up Up None 3
32767:4294967295 VplsPmsi not applicable Up Up None 3
32767:4294967296 VplsPmsi not applicable Up Up None 3
-------------------------------------------------------------------------------
Number of SDPs : 3
-------------------------------------------------------------------------------
===============================================================================
The following command displays SDP details information and Show Service-ID SDP Field Descriptions describes the output fields.
show service id sdp detail
Output Example
===============================================================================
Services: Service Destination Points Details
===============================================================================
Sdp Id 1:1 -(10.20.1.2)
-------------------------------------------------------------------------------
Description : Default sdp description
SDP Id : 1:1 Type : Spoke
VC Type : Ether VC Tag : n/a
Admin Path MTU : 0 Oper Path MTU : 9186
Far End : 10.20.1.2 Delivery : MPLS
Admin State : Up Oper State : Up
Acct. Pol : None Collect Stats : Disabled
Ingress Label : 2048 Egress Label : 2048
Ing mac Fltr : n/a Egr mac Fltr : n/a
Ing ip Fltr : n/a Egr ip Fltr : n/a
Ing ipv6 Fltr : n/a Egr ipv6 Fltr : n/a
Admin ControlWord : Not Preferred Oper ControlWord : False
Last Status Change : 05/31/2007 00:45:43 Signaling : None
Last Mgmt Change : 05/31/2007 00:45:43
Class Fwding State : Up
Flags : None
Peer Pw Bits : None
Peer Fault Ip : None
Peer Vccv CV Bits : None
Peer Vccv CC Bits : None
Max Nbr of MAC Addr: No Limit Total MAC Addr : 0
Learned MAC Addr : 0 Static MAC Addr : 0
MAC Learning : Enabled Discard Unkwn Srce: Disabled
MAC Aging : Enabled
L2PT Termination : Disabled BPDU Translation : Disabled
MAC Pinning : Disabled
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Max Drop Count : 3 Hold Down Time : 10
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
MCAC Policy Name :
MCAC Max Unconst BW: no limit MCAC Max Mand BW : no limit
MCAC In use Mand BW: 0 MCAC Avail Mand BW: unlimited
MCAC In use Opnl BW: 0 MCAC Avail Opnl BW: unlimited
Associated LSP LIST :
Lsp Name : A_B_1
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m35s
Lsp Name : A_B_2
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m35s
Lsp Name : A_B_3
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
Lsp Name : A_B_4
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
Lsp Name : A_B_5
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
Lsp Name : A_B_6
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
Lsp Name : A_B_7
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
Lsp Name : A_B_8
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m35s
Lsp Name : A_B_9
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
Lsp Name : A_B_10
Admin State : Up Oper State : Up
Time Since Last Tr*: 00h26m34s
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : enabled
Default LSP : A_B_10 Multicast LSP : A_B_9
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
af A_B_3
be A_B_1
ef A_B_6
h1 A_B_7
h2 A_B_5
l1 A_B_4
l2 A_B_2
nc A_B_8
===============================================================================
Stp Service Destination Point specifics
-------------------------------------------------------------------------------
Mac Move : Blockable
Stp Admin State : Up Stp Oper State : Down
Core Connectivity : Down
Port Role : N/A Port State : Forwarding
Port Number : 2049 Port Priority : 128
Port Path Cost : 10 Auto Edge : Enabled
Admin Edge : Disabled Oper Edge : N/A
Link Type : Pt-pt BPDU Encap : Dot1d
Root Guard : Disabled Active Protocol : N/A
Last BPDU from : N/A
Designated Bridge : N/A Designated Port Id: 0
Fwd Transitions : 0 Bad BPDUs rcvd : 0
Cfg BPDUs rcvd : 0 Cfg BPDUs tx : 0
TCN BPDUs rcvd : 0 TCN BPDUs tx : 0
RST BPDUs rcvd : 0 RST BPDUs tx : 0
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
The following command displays SDP details information and Show Service-ID SDP Field Descriptions describes the output fields.
show service id sdp detail
Output Example===============================================================================
Service Destination Point (Sdp Id : 130:1) Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 130:1 -(10.20.1.1)
-------------------------------------------------------------------------------
Description : (Not Specified)
SDP Id : 130:1 Type : Spoke
Spoke Descr : (Not Specified)
VC Type : n/a VC Tag : n/a
Admin Path MTU : 1600 Oper Path MTU : 1600
Delivery : MPLS
Far End : 10.20.1.1 Tunnel Far End :
Oper Tunnel Far End: 10.20.1.1
LSP Types : LDP
Hash Label : Disabled Hash Lbl Sig Cap : Disabled
Oper Hash Label : Disabled
Entropy Label : Disabled
Admin State : Up Oper State : Up
MinReqd SdpOperMTU : n/a
Adv Service MTU : 1500
Acct. Pol : None Collect Stats : Disabled
Ingress Label : 524236 Egress Label : 524257
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
Admin ControlWord : Not Preferred Oper ControlWord : False
BFD Template : BFD_VCCV
BFD-Enabled : yes BFD-Encap : ipv4
BFD Fail Action : down BFD Oper State : connected
BFD WaitForUpTimer : 0 secs
Last Status Change : 11/09/2020 17:04:44 Signaling : n/a
Last Mgmt Change : 11/09/2020 17:04:43
Class Fwding State : Down
Flags : None
Local Pw Bits : None
Peer Pw Bits : None
Peer Fault Ip : None
Peer Vccv CV Bits : lspPing bfdFaultDet
Peer Vccv CC Bits : mplsRouterAlertLabel
Application Profile: None
Transit Policy : None
AARP Id : None
Ingress Qos Policy : (none) Egress Qos Policy : (none)
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Max Drop Count : 3 Hold Down Time : 10
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 804 E. Fwd. Octets : 41892
-------------------------------------------------------------------------------
Control Channel Status
-------------------------------------------------------------------------------
PW Status : disabled Refresh Timer : <none>
Peer Status Expire : false
Request Timer : <none>
Acknowledgement : false
-------------------------------------------------------------------------------
ETH-CFM SDP-Bind specifics
-------------------------------------------------------------------------------
Squelch Levels : None
Collect Lmm Stats : Disabled
LMM FC Stats : None
LMM FC In Prof : None
-------------------------------------------------------------------------------
LDP Information :
-------------------------------------------------------------------------------
LDP LSP Id : 65537
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP List :
No LSPs Associated
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn
Multicast LSP : None
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
No FC Mappings
-------------------------------------------------------------------------------
Segment Routing
-------------------------------------------------------------------------------
ISIS : disabled
OSPF : disabled
TE-LSP : disabled
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
===============================================================================
Label |
Description |
---|---|
Sdp Id |
The SDP identifier. |
Type |
Indicates whether the SDP is a spoke or a mesh. |
Split Horizon Group |
Name of the split horizon group that the SDP belongs to. |
VC Type |
Displays the VC type: ether or vlan. |
VC Tag |
Displays the explicit dot1Q value used when encapsulating to the SDP far end. |
I. Lbl |
The VC label used by the far-end device to send packets to this device in this service by the SDP. |
Admin Path MTU |
The operating path MTU of the SDP is equal to the admin path MTU (when one is set) or the dynamically computed tunnel MTU, when no admin path MTU is set (the default case). |
Oper Path MTU |
The actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Far End addr/Far End |
Specifies the IP address of the remote end of the GRE or MPLS tunnel defined by this SDP. |
Delivery |
Specifies the type of delivery used by the SDP: GRE or MPLS. |
Adm/Admin State |
The administrative state of this SDP. |
Adv Service MTU |
Displays the configured advertise service MTU value (for Epipe services only). |
Opr/Oper State |
The operational state of this SDP. |
I.Lbl/Ingress Label |
The label used by the far-end device to send packets to this device in this service by this SDP. |
E.Lbl/Egress Label |
The label used by this device to send packets to the far-end device in this service by the SDP. |
BFD Template |
The BFD template name. |
BFD-Enabled |
The BFD enabled status. |
BFD-Encap |
The BFD encapsulation type. |
BFD Fail Action |
The BFD fail action. |
BFD Oper State |
The BFD operational state. |
BFD WaitForUpTimer |
The BFD wait for up timer value. |
Last Changed |
The date and time of the most recent change to the SDP. |
Signaling |
Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on this SDP. |
Admin State |
The administrative state of the keepalive process. |
Oper State |
The operational state of the keepalive process. |
Hello Time |
Specifies how often the SDP echo request messages are transmitted on this SDP. |
Max Drop Count |
Specifies the maximum number of consecutive SDP echo request messages that can be unacknowledged before the keepalive protocol reports a fault. |
Hello Msg Len |
Specifies the length of the SDP echo request messages transmitted on this SDP. |
Hold Down Time |
Specifies the amount of time to wait before the keepalive operating status is eligible to enter the alive state. |
I. Fwd. Pkts. |
Specifies the number of forwarded ingress packets. |
I. Dro. Pkts. |
Specifies the number of dropped ingress packets. |
E. Fwd. Pkts. |
Specifies the number of forwarded egress packets. |
Associated LSP List |
When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the far end field. If the SDP type is GRE, then the following message displays: SDP delivery mechanism is not MPLS. |
sdp
Syntax
sdp sdp-id pw-port [pw-port-id]
sdp sdp-id pw-port
sdp sdp-id pw-port [pw-port-id] [ statistics]
sdp [consistent | inconsistent | na] egressifs
sdp sdp-id keep-alive-history
sdp far-end ip-address | ipv6-address keep-alive-history
sdp [sdp-id] detail
sdp far-end ip-address | ipv6-address detail
Context
[Tree] (show>service sdp)
Full Context
show service sdp
Description
This command displays SDP information.
If no optional parameters are specified, a summary SDP output for all SDPs is displayed.
Parameters
- sdp-id
-
The SDP ID for which to display information.
- pw-port-id
-
Displays the SAP identifier for PW-SAPs.
- ip-address
-
Displays only SDPs matching with the specified far-end IP address.
- detail
-
Displays detailed SDP information.
- keep-alive-history
-
Displays the last fifty SDP keepalive events for the SDP.
Platforms
All
Output
The following output is an example of service SDP information.
Output Example============================================================================
*A:ALA-12>config>service# show service sdp 1 pw-port
===============================================================================
Service Destination Point (sdp Id 1 Pw-Port)
===============================================================================
Pw-port VC-Id Adm Encap Opr VC Type Egr Monitor
Shaper Oper
VPort Group
-------------------------------------------------------------------------------
1 1 up dot1q up ether
2 2 up qinq up ether
3 3 up dot1q up ether
4 4 up qinq up ether
-------------------------------------------------------------------------------
Entries found : 4
===============================================================================
*A:ALA-12>config>service# show service sdp 1 pw-port 3
===============================================================================
Service Destination Point (Sdp Id 1 Pw-Port 3)
===============================================================================
SDP Binding port : lag-1
VC-Id : 3 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Oper Flags : (Not Specified)
Monitor Oper-Group : (Not Specified)
===============================================================================
*A:ALA-12>config>service# show service sdp 1 pw-port 3 statistics
===============================================================================
Service Destination Point (Sdp Id 1 Pw-Port 3)
===============================================================================
SDP Binding port : lag-1
VC-Id : 3 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Oper Flags : (Not Specified)
Monitor Oper-Group : (Not Specified)
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
===============================================================================
sdp
Syntax
sdp sdp-id pw-port [pw-port-id]
sdp sdp-id pw-port
sdp sdp-id pw-port pw-port-id [ statistics]
sdp [consistent | inconsistent | na] egressifs
sdp sdp-id keep-alive-history
sdp far-end {ip-address | ipv6-address} keep-alive-history
sdp [sdp-id] detail
sdp far-end {ip-address | ipv6-address} [detail]
Context
[Tree] (show>service sdp)
Full Context
show service sdp
Description
This command displays information for the SDPs associated with the service.
If no optional parameters are specified, a summary of all associated SDPs is displayed.
Parameters
- sdp-id
-
Specifies the SDP ID for which to display information.
- pw-port-id
-
Specifies the pseudowire port identifier.
- ip-address
-
Displays only SDPs with the specified far-end IPv4 address. 64 characters maximum.
- ipv6-address
-
Displays only SDPs with the specified far-end IPv6 address. 64 characters maximum.
- detail
-
Displays detailed SDP information.
- keep-alive-history
-
Displays the last fifty SDP keepalive events for the SDP.
Platforms
All
Output
The following outputs are examples of SDP information.
Output Example*A:ALA-12>config>service# show service sdp 1 pw-port
===============================================================================
Service Destination Point (sdp Id 1 Pw-Port)
===============================================================================
Pw-port VC-Id Adm Encap Opr VC Type Egr Monitor
Shaper Oper
VPort Group
-------------------------------------------------------------------------------
1 1 up dot1q up ether
2 2 up qinq up ether
3 3 up dot1q up ether
4 4 up qinq up ether
-------------------------------------------------------------------------------
Entries found : 4
===============================================================================
*A:ALA-12>config>service# show service sdp 1 pw-port 3
===============================================================================
Service Destination Point (Sdp Id 1 Pw-Port 3)
===============================================================================
SDP Binding port : lag-1
VC-Id : 3 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Oper Flags : (Not Specified)
Monitor Oper-Group : (Not Specified)
===============================================================================
*A:ALA-12>config>service# show service sdp 1 pw-port 3 statistics
===============================================================================
Service Destination Point (Sdp Id 1 Pw-Port 3)
===============================================================================
SDP Binding port : lag-1
VC-Id : 3 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Oper Flags : (Not Specified)
Monitor Oper-Group : (Not Specified)
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
===============================================================================
*A:Dut-B# show service sdp detail
===============================================================================
Services: Service Destination Points Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 1 -10.20.1.3
-------------------------------------------------------------------------------
Description : Default sdp description
SDP Id : 1 SDP Source : manual
Admin Path MTU : 1514 Oper Path MTU : 1514
Delivery : MPLS
Far End : 10.20.1.3
Tunnel Far End : 10.20.1.3 LSP Types : LDP
Admin State : Up Oper State : Up
Signaling : TLDP Metric : 0
Acct. Pol : None Collect Stats : Disabled
Last Status Change : 06/13/2017 17:14:05 Adv. MTU Over. : No
Last Mgmt Change : 06/13/2017 17:17:19 VLAN VC Etype : 0x8100
Bw BookingFactor : 100 PBB Etype : 0x88e7
Oper Max BW(Kbps) : 0 Avail BW(Kbps) : 0
Net-Domain : default Egr Interfaces : Consistent
FPE LSP Id : 0
Weighted ECMP : Enabled
Flags : None
Mixed LSP Mode Information :
Mixed LSP Mode : Disabled Active LSP Type : LDP
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
Src B-MAC LSB : <none> Ctrl PW VC ID : <none>
Ctrl PW Active : n/a
-------------------------------------------------------------------------------
LDP Information :
-------------------------------------------------------------------------------
LDP LSP Id : 65662
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP List :
No LSPs Associated
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn Multicast LSP : None
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
No FC Mappings
-------------------------------------------------------------------------------
Segment Routing
-------------------------------------------------------------------------------
ISIS : disabled
OSPF : disabled
TE-LSP : disabled
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
===============================================================================
*A:Dut-B#
sdp
Syntax
sdp sdp-id pw-port [pw-port-id]
sdp sdp-id pw-port
sdp sdp-id pw-port pw-port-id [statistics]
sdp [consistent | inconsistent | na] egressifs
sdp sdp-id keep-alive-history
sdp far-end {ip-address | ipv6-address} keep-alive-history
sdp [sdp-id] [detail]
sdp far-end {ip-address | ipv6-address} [detail]
Context
[Tree] (show>service sdp)
Full Context
show service sdp
Description
This command displays information for the SDPs associated with the service.
If no optional parameters are specified, a summary of all associated SDPs is displayed.
Parameters
- sdp-id
-
Specifies the SDP ID for which to display information.
- pw-port-id
-
Specifies the pseudo-wire port identifier.
- statistics
-
Displays SDP statistics information.
- consistent
-
Indicates that the network-domains for all the egress network interfaces that can carry traffic on this SDP are consistent.
- inconsistent
-
Indicates that the network-domain for one or more egress network interfaces that can carry traffic on this SDP are inconsistent.
- na
-
Indicates that there is no egress network interface that can carry traffic on this SDP.
- egressifs
-
Indicates whether all the egress network interfaces that can carry traffic on this SDP are associated with the network-domain configured on this SDP.
- ip-address | ipv6-address
-
Displays only SDPs matching with the specified far-end IP address up to 64 characters.
- keep-alive-history
-
Displays the last fifty SDP keepalive events for the SDP.
- detail
-
Displays detailed SDP information.
Platforms
All
Output
The following output is an example of SDP information, and Show Service SDP Field Descriptions describes the output fields.
Output Example*A:ALA-12>config>service# show service sdp 1 pw-port
===============================================================================
Service Destination Point (sdp Id 1 Pw-Port)
===============================================================================
Pw-port VC-Id Adm Encap Opr VC Type Egr Monitor
Shaper Oper
VPort Group
-------------------------------------------------------------------------------
1 1 up dot1q up ether
2 2 up qinq up ether
3 3 up dot1q up ether
4 4 up qinq up ether
-------------------------------------------------------------------------------
Entries found : 4
===============================================================================
*A:ALA-12>config>service# show service sdp 1 pw-port 3
===============================================================================
Service Destination Point (Sdp Id 1 Pw-Port 3)
===============================================================================
SDP Binding port : lag-1
VC-Id : 3 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Oper Flags : (Not Specified)
Monitor Oper-Group : (Not Specified)
===============================================================================
*A:ALA-12>config>service# show service sdp 1 pw-port 3 statistics
===============================================================================
Service Destination Point (Sdp Id 1 Pw-Port 3)
===============================================================================
SDP Binding port : lag-1
VC-Id : 3 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Oper Flags : (Not Specified)
Monitor Oper-Group : (Not Specified)
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
===============================================================================
*A:Dut-B# show service sdp
============================================================================
Services: Service Destination Points
============================================================================
SdpId AdmMTU OprMTU Far End Adm Opr Del LSP Sig
----------------------------------------------------------------------------
230 0 1582 10.20.1.3 Up Up MPLS I TLDP
----------------------------------------------------------------------------
Number of SDPs : 1
----------------------------------------------------------------------------
Legend: R = RSVP, L = LDP, B = BGP, M = MPLS-TP, n/a = Not Applicable
============================================================================
*A:Dut-B#
*A:Dut-B# show service sdp detail
===============================================================================
Services: Service Destination Points Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 230 -10.20.1.3
-------------------------------------------------------------------------------
Description : (Not Specified)
SDP Id : 230 SDP Source : manual
Admin Path MTU : 0 Oper Path MTU : 1582
Delivery : MPLS
Far End : 10.20.1.3
Tunnel Far End : n/a LSP Types : SR-ISIS
Admin State : Up Oper State : Up
Signaling : TLDP Metric : 0
Acct. Pol : None Collect Stats : Disabled
Last Status Change : 01/28/2015 22:00:07 Adv. MTU Over. : No
Last Mgmt Change : 01/28/2015 21:59:53 VLAN VC Etype : 0x8100
Bw BookingFactor : 100 PBB Etype : 0x88e7
Oper Max BW(Kbps) : 0 Avail BW(Kbps) : 0
Net-Domain : default Egr Interfaces : Consistent
Flags : None
Mixed LSP Mode Information :
Mixed LSP Mode : Disabled Active LSP Type : SR-ISIS
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
Src B-MAC LSB : <none> Ctrl PW VC ID : <none>
Ctrl PW Active : n/a
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP List :
No LSPs Associated
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn Multicast LSP : None
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
No FC Mappings
-------------------------------------------------------------------------------
Segment Routing
-------------------------------------------------------------------------------
ISIS : enabled LSP Id : 524289
Oper Instance Id : 0
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
===============================================================================
*A:Dut-B#
*A:Dut-B>config>service>sdp# show service sdp
============================================================================
Services: Service Destination Points
============================================================================
SdpId AdmMTU OprMTU Far End Adm Opr Del LSP Sig
----------------------------------------------------------------------------
230 0 1582 10.20.1.3 Up Up MPLS O TLDP
----------------------------------------------------------------------------
Number of SDPs : 1
----------------------------------------------------------------------------
Legend: R = RSVP, L = LDP, B = BGP, M = MPLS-TP, n/a = Not Applicable
I = SR-ISIS, O = SR-OSPF
============================================================================
*A:ALA-12# show service sdp 2 detail
===============================================================================
Service Destination Point (Sdp Id : 2) Details
-------------------------------------------------------------------------------
Sdp Id 2 -(10.10.10.104)
-------------------------------------------------------------------------------
Description : GRE-10.10.10.104
SDP Id : 2
Admin Path MTU : 0 Oper Path MTU : 0
Far End : 10.10.10.104 Delivery : GRE
Admin State : Up Oper State : Down
Weighted ECMP : Disabled VLAN VC Etype : 0x8100
Flags : SignalingSessDown TransportTunnDown
Signaling : TLDP Adv. MTU Over. : No
Last Status Change : 02/01/2007 09:11:39
Last Mgmt Change : 02/01/2007 09:11:46
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
Associated LSP LIST :
SDP Delivery Mechanism is not MPLS
===============================================================================
*A:ALA-12#
Label |
Description |
---|---|
SDP Id |
The SDP identifier. |
Adm MTU |
Specifies the desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Opr MTU |
Specifies the actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
IP address |
Specifies the IP address of the remote end of the GRE or MPLS tunnel defined by this SDP. |
Adm |
Admin State — Specifies the administrative state of the SDP. |
Opr |
Oper State — Specifies the operational state of the SDP. |
Deliver |
Specifies the type of delivery used by the SDP: GRE or MPLS. |
Flags |
Specifies the conditions that affect the operating status of this SDP. |
Signal Signaling |
Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on the SDP. |
Last Status Change |
Specifies the time of the most recent operating status change to this SDP. |
sdp
Syntax
sdp sdp-id pw-port [pw-port-id]
sdp sdp-id pw-port
sdp sdp-id pw-port pw-port-id [statistics]
sdp [consistent | inconsistent | na] egressifs
sdp sdp-id keep-alive-history
sdp far-end {ip-address | ipv6-address} keep-alive-history
sdp [sdp-id] [detail]
sdp far-end {ip-address | ipv6-address} [detail]
Context
[Tree] (show>service sdp)
Full Context
show service sdp
Description
This command displays information for the SDPs associated with the service.
If no optional parameters are specified, a summary of all associated SDPs is displayed.
Parameters
- sdp-id
-
Specifies the SDP ID for which to display information.
- pw-port-id
-
Specifies the pseudo-wire port identifier.
- statistics
-
Displays SDP statistics information.
- consistent
-
Indicates that the network-domains for all the egress network interfaces that can carry traffic on this SDP are consistent.
- inconsistent
-
Indicates that the network-domain for one or more egress network interfaces that can carry traffic on this SDP are inconsistent.
- na
-
Indicates that there is no egress network interface that can carry traffic on this SDP.
- egressifs
-
Indicates whether all the egress network interfaces that can carry traffic on this SDP are associated with the network-domain configured on this SDP.
- ip-address | ipv6-address
-
Displays only SDPs matching with the specified far-end IP address. 64 characters maximum.
- keep-alive-history
-
Displays the last fifty SDP keepalive events for the SDP.
- detail
-
Displays detailed SDP information.
Platforms
All
Output
The following output is an example of SDP information.
Output Example*A:ALA-12>config>service# show service sdp 1 pw-port
===============================================================================
Service Destination Point (sdp Id 1 Pw-Port)
===============================================================================
Pw-port VC-Id Adm Encap Opr VC Type Egr Monitor
Shaper Oper
VPort Group
-------------------------------------------------------------------------------
1 1 up dot1q up ether
2 2 up qinq up ether
3 3 up dot1q up ether
4 4 up qinq up ether
-------------------------------------------------------------------------------
Entries found : 4
===============================================================================
*A:ALA-12>config>service# show service sdp 1 pw-port 3
===============================================================================
Service Destination Point (Sdp Id 1 Pw-Port 3)
===============================================================================
SDP Binding port : lag-1
VC-Id : 3 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Oper Flags : (Not Specified)
Monitor Oper-Group : (Not Specified)
===============================================================================
*A:ALA-12>config>service# show service sdp 1 pw-port 3 statistics
===============================================================================
Service Destination Point (Sdp Id 1 Pw-Port 3)
===============================================================================
SDP Binding port : lag-1
VC-Id : 3 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Oper Flags : (Not Specified)
Monitor Oper-Group : (Not Specified)
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
===============================================================================
The following output is an example of SDP information, and Show Service SDP Field Descriptions describes the output fields.
Output Example*A:ALA-12# show service sdp
==============================================================================
Services: Service Destination Points
==============================================================================
SdpId Adm MTU Opr MTU IP address Adm Opr Deliver Signal
------------------------------------------------------------------------------
10 4462 4462 10.20.1.3 Up Dn NotReady MPLS TLDP
40 4462 1534 10.20.1.20 Up Up MPLS TLDP
60 4462 1514 10.20.1.21 Up Up GRE TLDP
100 4462 4462 203.0.0.2 Down Down GRE TLDP
500 4462 4462 10.20.1.50 Up Dn NotReady GRE TLDP
------------------------------------------------------------------------------
Number of SDPs : 5
==============================================================================
*A:ALA-12#
*A:ALA-12# show service sdp 2 detail
===============================================================================
Service Destination Point (Sdp Id : 2) Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 2 -(10.10.10.104)
-------------------------------------------------------------------------------
Description : GRE-10.10.10.104
SDP Id : 2
Admin Path MTU : 0 Oper Path MTU : 0
Far End : 10.10.10.104 Delivery : GRE
Admin State : Up Oper State : Down
Flags : SignalingSessDown TransportTunnDown
Signaling : TLDP VLAN VC Etype : 0x8100
Last Status Change : 02/01/2007 09:11:39 Adv. MTU Over. : No
Last Mgmt Change : 02/01/2007 09:11:46
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
Associated LSP LIST :
SDP Delivery Mechanism is not MPLS
===============================================================================
*A:ALA-12#
*A:Dut-B# show service sdp
============================================================================
Services: Service Destination Points
============================================================================
SdpId AdmMTU OprMTU Far End Adm Opr Del LSP Sig
----------------------------------------------------------------------------
230 0 1582 10.20.1.3 Up Up MPLS I TLDP
----------------------------------------------------------------------------
Number of SDPs : 1
----------------------------------------------------------------------------
Legend: R = RSVP, L = LDP, B = BGP, M = MPLS-TP, n/a = Not Applicable
============================================================================
*A:Dut-B#
*A:Dut-B# show service sdp detail
===============================================================================
Services: Service Destination Points Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 230 -10.20.1.3
-------------------------------------------------------------------------------
Description : (Not Specified)
SDP Id : 230 SDP Source : manual
Admin Path MTU : 0 Oper Path MTU : 1582
Delivery : MPLS
Far End : 10.20.1.3
Tunnel Far End : n/a LSP Types : SR-ISIS
Admin State : Up Oper State : Up
Signaling : TLDP Metric : 0
Acct. Pol : None Collect Stats : Disabled
Last Status Change : 01/28/2015 22:00:07 Adv. MTU Over. : No
Last Mgmt Change : 01/28/2015 21:59:53 VLAN VC Etype : 0x8100
Bw BookingFactor : 100 PBB Etype : 0x88e7
Oper Max BW(Kbps) : 0 Avail BW(Kbps) : 0
Net-Domain : default Egr Interfaces : Consistent
Flags : None
Mixed LSP Mode Information :
Mixed LSP Mode : Disabled Active LSP Type : SR-ISIS
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
Src B-MAC LSB : <none> Ctrl PW VC ID : <none>
Ctrl PW Active : n/a
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP List :
No LSPs Associated
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn Multicast LSP : None
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
No FC Mappings
-------------------------------------------------------------------------------
Segment Routing
-------------------------------------------------------------------------------
ISIS : enabled LSP Id : 524289
Oper Instance Id : 0
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
===============================================================================
*A:Dut-B#
*A:ALA-12# show service sdp 8
==============================================================================
Service Destination Point (Sdp Id : 8)
==============================================================================
SdpId Adm MTU Opr MTU IP address Adm Opr Deliver Signal
------------------------------------------------------------------------------
8 4462 4462 10.10.10.104 Up Dn NotReady MPLS TLDP
==============================================================================
Service Destination Point (Sdp Id : 8) Details
-------------------------------------------------------------------------------
Sdp Id 8 -(10.10.10.104)
-------------------------------------------------------------------------------
Description : MPLS-10.10.10.104
SDP Id : 8
Admin Path MTU : 0 Oper Path MTU : 0
Far End : 10.10.10.104 Delivery : MPLS
Admin State : Up Oper State : Down
Flags : SignalingSessDown TransportTunnDown
Signaling : TLDP VLAN VC Etype : 0x8100
Last Status Change : 02/01/2007 09:11:39 Adv. MTU Over. : No
Last Mgmt Change : 02/01/2007 09:11:46
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
Associated LSP LIST :
Lsp Name : to-104
Admin State : Up Oper State : Down
Time Since Last Tran*: 01d07h36m
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:ALA-12#
Label |
Description |
---|---|
SDP Id |
The SDP identifier. |
Adm MTU |
Specifies the largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
Opr MTU |
Specifies the actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end router, without requiring the packet to be fragmented. |
IP address |
Specifies the IP address of the remote end of the GRE or MPLS tunnel defined by this SDP. |
Adm |
Admin State — Specifies the state of the SDP. |
Opr |
Oper State —Specifies the operating state of the SDP. |
Flags |
Specifies all the conditions that affect the operating status of this SDP. |
Signal |
Signaling — Specifies the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on the SDP. |
Last Status Change |
Specifies the time of the most recent operating status change to this SDP. |
Last Mgmt Change |
Specifies the time of the most recent management-initiated change to this SDP. |
Number of SDPs |
Specifies the total number of SDPs displayed according to the criteria specified. |
Hello Time |
Specifies how often the SDP echo request messages are transmitted on this SDP. |
Deliver |
Delivered — Specifies the type of delivery used by the SDP: GRE or MPLS. |
Number of SDPs |
Specifies the total number of SDPs displayed according to the criteria specified. |
Hello Time |
Specifies how often the SDP echo request messages are transmitted on this SDP. |
Hello Msg Len |
Specifies the length of the SDP echo request messages transmitted on this SDP. |
Hello Timeout |
Specifies the number of seconds to wait for an SDP echo response message before declaring a timeout. |
Unmatched Replies |
Specifies the number of SDP unmatched message replies. |
Max Drop Count |
Specifies the maximum number of consecutive SDP echo request messages that can be unacknowledged before the keepalive protocol reports a fault. |
Hold Down Time |
Specifies the maximum number of consecutive SDP echo request messages that can be unacknowledged before the keepalive protocol reports a fault. |
TX Hello Msgs |
Specifies the number of SDP echo request messages transmitted since the keepalive was administratively enabled or the counter was cleared. |
Rx Hello Msgs |
Specifies the number of SDP echo request messages received since the keepalive was administratively enabled or the counter was cleared. |
Associated LSP List |
When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the far end field. If the SDP type is GRE, then the following message displays: SDP delivery mechanism is not MPLS. |
sdp
Syntax
sdp sdp-id pw-port [pw-port-id] [statistics]
sdp [consistent | inconsistent | na] egressifs
sdp sdp-id keep-alive-history
sdp far-end ip-address keep-alive-history
sdp [sdp-id] [detail]
sdp far-end ip-address [detail]
Context
[Tree] (show>service sdp)
Full Context
show service sdp
Description
This command displays SDP information.
If no optional parameters are specified, a summary SDP output for all SDPs is displayed.
Parameters
- sdp-id
-
The SDP ID for which to display information.
- far-end ip-address
-
Displays only SDPs matching with the specified far-end IP address.
- detail
-
Displays detailed SDP information.
- keep-alive-history
-
Displays the last fifty SDP keepalive events for the SDP.
- pw-port pw-port-id
-
Displays the SAP identifier for PW-SAPs.
Platforms
All
Output
The following output is an example of SDP information.
Service Commands SDP Field Descriptions describes the show service SDP output fields.
Output Example*A:Dut-D# show service id 1 sdp 17407:4294967294 detail
=======================================================================
Service Destination Point (Sdp Id : 17407:4294967294) Details
=======================================================================
-------------------------------------------------------------------------------
Sdp Id 17407:4294967294 -(not applicable)
-----------------------------------------------------------------------
Description : (Not Specified)
SDP Id : 17407:4294967294 Type : VplsPmsi
Split Horiz Grp : (Not Specified)
VC Type : Ether VC Tag : n/a
Admin Path MTU : 9194 Oper Path MTU : 9194
Delivery : MPLS
Far End : not applicable
Tunnel Far End : n/a LSP Types : None
Hash Label : Disabled Hash Lbl Sig Cap : Disabled
Oper Hash Label : Disabled
Admin State : Up Oper State : Up
Acct. Pol : None Collect Stats : Disabled
Ingress Label : 0 Egress Label : 3
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
Admin ControlWord : Not Preferred Oper ControlWord : False
Last Status Change : 12/14/2012 12:42:22 Signaling : None
Last Mgmt Change : 12/14/2012 12:42:19 Force Vlan-Vc : Disabled
Endpoint : N/A Precedence : 4
PW Status Sig : Enabled
Class Fwding State : Down
Flags : None
Time to RetryReset : never Retries Left : 3
Mac Move : Blockable Blockable Level : Tertiary
Local Pw Bits : None
Peer Pw Bits : None
Peer Fault Ip : None
Peer Vccv CV Bits : None
Peer Vccv CC Bits : None
Application Profile: None
Max Nbr of MAC Addr: No Limit Total MAC Addr : 0
Learned MAC Addr : 0 Static MAC Addr : 0
MAC Learning : Enabled Discard Unkwn Srce: Disabled
MAC Aging : Enabled
BPDU Translation : Disabled
L2PT Termination : Disabled
MAC Pinning : Disabled
Ignore Standby Sig : False Block On Mesh Fail: False
Oper Group : (none) Monitor Oper Grp : (none)
Rest Prot Src Mac : Disabled
Auto Learn Mac Prot: Disabled RestProtSrcMacAct : Disable
Ingress Qos Policy : (none) Egress Qos Policy : (none)
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
-----------------------------------------------------------------------
ETH-CFM SDP-Bind specifics
-----------------------------------------------------------------------
V-MEP Filtering : Disabled
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Max Drop Count : 3 Hold Down Time : 10
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 2979761 E. Fwd. Octets : 476761760
-----------------------------------------------------------------------
Control Channel Status
-----------------------------------------------------------------------
PW Status : disabled Refresh Timer : <none>
Peer Status Expire : false Clear On Timeout : true
MCAC Policy Name :
MCAC Max Unconst BW: no limit MCAC Max Mand BW : no limit
MCAC In use Mand BW: 0 MCAC Avail Mand BW: unlimited
MCAC In use Opnl BW: 0 MCAC Avail Opnl BW: unlimited
-----------------------------------------------------------------------
RSVP/Static LSPs
-----------------------------------------------------------------------
Associated LSP List :
No LSPs Associated
-----------------------------------------------------------------------
Class-based forwarding :
-----------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn Multicast LSP : None
=======================================================================
FC Mapping Table
=======================================================================
FC Name LSP Name
-----------------------------------------------------------------------
No FC Mappings
-----------------------------------------------------------------------
Stp Service Destination Point specifics
-----------------------------------------------------------------------
Stp Admin State : Down Stp Oper State : Down
Core Connectivity : Down
Port Role : N/A Port State : Forwarding
Port Number : 0 Port Priority : 128
Port Path Cost : 10 Auto Edge : Enabled
Admin Edge : Disabled Oper Edge : N/A
Link Type : Pt-pt BPDU Encap : Dot1d
Root Guard : Disabled Active Protocol : N/A
Last BPDU from : N/A
Designated Bridge : N/A Designated Port Id: N/A
Fwd Transitions : 0 Bad BPDUs rcvd : 0
Cfg BPDUs rcvd : 0 Cfg BPDUs tx : 0
TCN BPDUs rcvd : 0 TCN BPDUs tx : 0
TC bit BPDUs rcvd : 0 TC bit BPDUs tx : 0
RST BPDUs rcvd : 0 RST BPDUs tx : 0
-----------------------------------------------------------------------
Number of SDPs : 1
-----------------------------------------------------------------------
=======================================================================
A:Dut-F# show service sdp 1600 detail
===============================================================================
Service Destination Point (Sdp Id : 1600) Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 1600 -2.2.2.2
-------------------------------------------------------------------------------
Description : (Not Specified)
SDP Id : 1600 SDP Source : manual
Admin Path MTU : 0 Oper Path MTU : 1532
Delivery : GRE
Far End : 2.2.2.2 Tunnel Far End : n/a
Oper Tunnel Far End : 2.2.2.2
Local End : 6.6.6.6
LSP Types : n/a
Admin State : Up Oper State : Up
Signaling : TLDP Metric : 0
Acct. Pol : None Collect Stats : Disabled
Last Status Change : 10/04/2018 21:18:06 Adv. MTU Over. : No
Last Mgmt Change : 10/04/2018 21:17:59 VLAN VC Etype : 0x8100
Bw BookingFactor : 100
Oper Max BW(Kbps) : 0 Avail BW(Kbps) : 0
Net-Domain : default Egr Interfaces : Consistent
Allow Fragmentation : No
FPE LSP Id : 0
Weighted ECMP : Disabled
Flags : None
Mixed LSP Mode Information :
Mixed LSP Mode : n/a Active LSP Type : n/a
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
-------------------------------------------------------------------------------
MPLS-TP LSPs
-------------------------------------------------------------------------------
Associated LSP List :
SDP Delivery Mechanism is not MPLS
-------------------------------------------------------------------------------
Segment Routing
-------------------------------------------------------------------------------
ISIS : disabled
OSPF : disabled
TE-LSP : disabled
===============================================================================
*A:Dut-B# show service sdp
============================================================================
Services: Service Destination Points
============================================================================
SdpId AdmMTU OprMTU Far End Adm Opr Del LSP Sig
----------------------------------------------------------------------------
230 0 1582 10.20.1.3 Up Up MPLS I TLDP
----------------------------------------------------------------------------
Number of SDPs : 1
----------------------------------------------------------------------------
Legend: R = RSVP, L = LDP, B = BGP, M = MPLS-TP, n/a = Not Applicable
============================================================================
*A:Dut-B#
*A:Dut-B# show service sdp detail
===============================================================================
Services: Service Destination Points Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 230 -10.20.1.3
-------------------------------------------------------------------------------
Description : (Not Specified)
SDP Id : 230 SDP Source : manual
Admin Path MTU : 0 Oper Path MTU : 1582
Delivery : MPLS
Far End : 10.20.1.3
Tunnel Far End : n/a LSP Types : SR-ISIS
Admin State : Up Oper State : Up
Signaling : TLDP Metric : 0
Acct. Pol : None Collect Stats : Disabled
Last Status Change : 01/28/2015 22:00:07 Adv. MTU Over. : No
Last Mgmt Change : 01/28/2015 21:59:53 VLAN VC Etype : 0x8100
Bw BookingFactor : 100 PBB Etype : 0x88e7
Oper Max BW(Kbps) : 0 Avail BW(Kbps) : 0
Net-Domain : default Egr Interfaces : Consistent
Flags : None
Mixed LSP Mode Information :
Mixed LSP Mode : Disabled Active LSP Type : SR-ISIS
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
Src B-MAC LSB : <none> Ctrl PW VC ID : <none>
Ctrl PW Active : n/a
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP List :
No LSPs Associated
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn Multicast LSP : None
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
No FC Mappings
-------------------------------------------------------------------------------
Segment Routing
-------------------------------------------------------------------------------
ISIS : enabled LSP Id : 524289
Oper Instance Id : 0
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
===============================================================================
*A:Dut-B#
*A:Dut-B> show service sdp
============================================================================
Services: Service Destination Points
============================================================================
SdpId AdmMTU OprMTU Far End Adm Opr Del LSP Sig
----------------------------------------------------------------------------
230 0 1582 10.20.1.3 Up Up MPLS O TLDP
----------------------------------------------------------------------------
Number of SDPs : 1
----------------------------------------------------------------------------
Legend: R = RSVP, L = LDP, B = BGP, M = MPLS-TP, n/a = Not Applicable
I = SR-ISIS, O = SR-OSPF
============================================================================
*A:Dut-B> show service sdp 230 detail
===============================================================================
Service Destination Point (Sdp Id : 230) Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 230 -10.20.1.3
-------------------------------------------------------------------------------
Description : (Not Specified)
SDP Id : 230 SDP Source : manual
Admin Path MTU : 0 Oper Path MTU : 1582
Delivery : MPLS
Far End : 10.20.1.3
Tunnel Far End : n/a LSP Types : SR-OSPF
Admin State : Up Oper State : Up
Signaling : TLDP Metric : 0
Acct. Pol : None Collect Stats : Disabled
Last Status Change : 05/27/2015 03:08:37 Adv. MTU Over. : No
Last Mgmt Change : 05/27/2015 03:05:36 VLAN VC Etype : 0x8100
Bw BookingFactor : 100 PBB Etype : 0x88e7
Oper Max BW(Kbps) : 0 Avail BW(Kbps) : 0
Net-Domain : default Egr Interfaces : Consistent
Flags : None
Mixed LSP Mode Information :
Mixed LSP Mode : Disabled Active LSP Type : SR-OSPF
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
Src B-MAC LSB : <none> Ctrl PW VC ID : <none>
Ctrl PW Active : n/a
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP List :
No LSPs Associated
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn Multicast LSP : None
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
No FC Mappings
-------------------------------------------------------------------------------
Segment Routing
-------------------------------------------------------------------------------
OSPF : enabled LSP Id : 524289
Oper Instance Id : 0
===============================================================================
*A:Dut-B>config>service>sdp#
*A:ALA-12# show service sdp 8
==============================================================================
Service Destination Point (Sdp Id : 8)
==============================================================================
SdpId Adm MTU Opr MTU IP address Adm Opr Deliver Signal
------------------------------------------------------------------------------
8 4462 4462 10.10.10.104 Up Dn NotReady MPLS TLDP
==============================================================================
*A:ALA-12#
*A:ALA-12#
===============================================================================
Service Destination Point (Sdp Id : 8) Details
===============================================================================
Sdp Id 8 -(10.10.10.104)
-------------------------------------------------------------------------------
Description : MPLS-10.10.10.104
SDP Id : 8
Admin Path MTU : 0 Oper Path MTU : 0
Far End : 10.10.10.104 Delivery : MPLS
Admin State : Up Oper State : Down
Flags : SignalingSessDown TransportTunnDown
Signaling : TLDP VLAN VC Etype : 0x8100
Last Status Change : 02/01/2007 09:11:39 Adv. MTU Over. : No
Last Mgmt Change : 02/01/2007 09:11:46
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
Associated LSP LIST :
Lsp Name : to-104
Admin State : Up Oper State : Down
Time Since Last Tran*: 01d07h36m
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:ALA-12#
*A:MV-SR12> show service sdp 10 detail
===============================================================================
Service Destination Point (Sdp Id : 10) Details
===============================================================================
Sdp Id 10 -(203.20.1.201)
-------------------------------------------------------------------------------
Description : (Not Specified)
SDP Id : 10 SDP Source : manual
Admin Path MTU : 0 Oper Path MTU : 9182
Far End : 203.20.1.201 Delivery : MPLS/LDP
Admin State : Up Oper State : Up
Signaling : TLDP Metric : 0
Acct. Pol : None Collect Stats : Disabled
Last Status Change : 02/12/2010 22:37:08 Adv. MTU Over. : No
Last Mgmt Change : 02/12/2010 22:37:03 VLAN VC Etype : 0x8100
Bw BookingFactor : 100 PBB Etype : 0x88e7
Oper Max BW(Kbps) : 0 Avail BW(Kbps) : 0
Net-Domain : default Egr Interfaces : Consistent
Mixed LSP Mode : Enabled
Revert Time : 0 Revert Count Down : n/a
Flags : None
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
-------------------------------------------------------------------------------
LDP Information :
-------------------------------------------------------------------------------
LDP LSP Id : 65539 LDP Active : No
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP LIST :
Lsp Name : To_7710
Admin State : Up Oper State : Up
Time Since Last Tran*: 01h20m56s
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn Multicast LSP : None
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
No FC Mappings
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:MV-SR12>config>service>vprn#
*B:Dut-B>config>router>mpls>lsp# /show service sdp
============================================================================
Services: Service Destination Points
============================================================================
SdpId AdmMTU OprMTU Far End Adm Opr Del LSP Sig
----------------------------------------------------------------------------
230 0 1578 Up Up MPLS I TLDP
2001:db8::
----------------------------------------------------------------------------
Number of SDPs : 1
----------------------------------------------------------------------------
Legend: R = RSVP, L = LDP, B = BGP, M = MPLS-TP, n/a = Not Applicable
I = SR-ISIS, O = SR-OSPF, T = SR-TE, F = FPE
============================================================================
*B:Dut-B>config>router>mpls>lsp# /show service sdp detail
===============================================================================
Services: Service Destination Points Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 230 2001:db8::
-------------------------------------------------------------------------------
Description : Default sdp description
SDP Id : 230 SDP Source : manual
Admin Path MTU : 0 Oper Path MTU : 1578
Delivery : MPLS
Far End : 2001:db8::
Tunnel Far End : n/a LSP Types : SR-ISIS
Admin State : Up Oper State : Up
Signaling : TLDP Metric : 0
Acct. Pol : None Collect Stats : Disabled
Last Status Change : 07/12/2016 19:40:17 Adv. MTU Over. : No
Last Mgmt Change : 07/12/2016 19:40:04 VLAN VC Etype : 0x8100
Bw BookingFactor : 100 PBB Etype : 0x88e7
Oper Max BW(Kbps) : 0 Avail BW(Kbps) : 0
Net-Domain : default Egr Interfaces : Consistent
FPE LSP Id : 0
Flags : None
Mixed LSP Mode Information :
Mixed LSP Mode : Disabled Active LSP Type : SR-ISIS
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 5 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
Src B-MAC LSB : <none> Ctrl PW VC ID : <none>
Ctrl PW Active : n/a
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP List :
No LSPs Associated
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn Multicast LSP : None
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
No FC Mappings
-------------------------------------------------------------------------------
Segment Routing
-------------------------------------------------------------------------------
ISIS : enabled LSP Id : 524355
Oper Instance Id : 0
OSPF : disabled
TE-LSP : disabled
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
===============================================================================
*B:Dut-B>config>router>mpls>lsp# /show service id 1 sdp detail
===============================================================================
Services: Service Destination Points Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 230:1 -(2001:db8::)
-------------------------------------------------------------------------------
Description : Default sdp description
SDP Id : 230:1 Type : Spoke
Spoke Descr : Description for Sdp Bind 230 for Svc ID 1
VC Type : VLAN VC Tag : 0
Admin Path MTU : 0 Oper Path MTU : 1578
Delivery : MPLS
Far End : 2001:db8::
Tunnel Far End : n/a LSP Types : SR-ISIS
Hash Label : Disabled Hash Lbl Sig Cap : Disabled
Oper Hash Label : Disabled
Entropy Label : Disabled
Admin State : Up Oper State : Up
MinReqd SdpOperMTU : 1514
Adv Service MTU : n/a
Acct. Pol : None Collect Stats : Disabled
Ingress Label : 262134 Egress Label : 262134
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
Admin ControlWord : Not Preferred Oper ControlWord : False
Admin BW(Kbps) : 0 Oper BW(Kbps) : 0
BFD Template : None
BFD-Enabled : no BFD-Encap : ipv4
Last Status Change : 07/12/2016 19:40:18 Signaling : TLDP
Last Mgmt Change : 07/12/2016 19:40:04
Endpoint : N/A Precedence : 4
PW Status Sig : Enabled
Force Vlan-Vc : Disabled Force Qinq-Vc : Disabled
Class Fwding State : Down
Flags : None
Local Pw Bits : None
Peer Pw Bits : None
Peer Fault Ip : None
Peer Vccv CV Bits : lspPing bfdFaultDet
Peer Vccv CC Bits : mplsRouterAlertLabel
Application Profile: None
Transit Policy : None
Standby Sig Slave : False
Block On Peer Fault: False
Use SDP B-MAC : False
Ingress Qos Policy : (none) Egress Qos Policy : (none)
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Max Drop Count : 3 Hold Down Time : 10
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
-------------------------------------------------------------------------------
Control Channel Status
-------------------------------------------------------------------------------
PW Status : disabled Refresh Timer : <none>
Peer Status Expire : false
Request Timer : <none>
Acknowledgement : false
-------------------------------------------------------------------------------
ETH-CFM SDP-Bind specifics
-------------------------------------------------------------------------------
Squelch Levels : None
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP List :
No LSPs Associated
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn Multicast LSP : None
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
No FC Mappings
-------------------------------------------------------------------------------
Segment Routing
-------------------------------------------------------------------------------
ISIS : enabled LSP Id : 524355
Oper Instance Id : 0
OSPF : disabled
TE-LSP : disabled
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
===============================================================================
When network domains are configured, the SDP egress interface state can be verified by using the following command.
*A:Dut-T# show service sdp egressifs
===============================================================================
SDP Egress Ifs State Table
===============================================================================
SDP Id Network Domain State
-------------------------------------------------------------------------------
100 net1 consistent
-------------------------------------------------------------------------------
SDPs : 1
===============================================================================
*A:Dut-Tr#
*A:Dut-C># show service sdp 1 pw-port
============================================================================
Service Destination Point (Sdp Id 1 Pw-Port )
=============================================================================
SDP Binding port : 1/1/3
SDP: 1 Pw-port: 11
----------------------------------------------------------------------------
VC-Id : 11 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : vlan Vlan VC Tag : 0
Oper Flags : (Not Specified)
SDP: 1 Pw-port: 44
-------------------------------------------------------------------------------
VC-Id : 2 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Oper Flags : (Not Specified)
----------------------------------------------------------------------------
Entries found: 2
-----------------------------------------------------------------------------
*A:Dut-C> #
*A:Dut-C> # show service sdp 1 pw-port 44
============================================================================
Service Destination Point (Sdp Id 1 Pw-Port 44)
============================================================================
SDP Binding port : 1/1/3
VC-Id : 2 Admin Status : up
Encap : dot1q Oper Status : up
VC Type : ether
Oper Flags : (Not Specified)
============================================================================
*A:Dut-C> #
The following show output gives the source-bmac-lsb and control PW used for a given SDP.
A:bksim1613# show service sdp 1 detail
===============================================================================
Service Destination Point (Sdp Id : 1) Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 1 -2.2.2.2
-------------------------------------------------------------------------------
Description : (Not Specified)
SDP Id : 1 SDP Source : manual
Admin Path MTU : 0 Oper Path MTU : 1556
Delivery : MPLS
Far End : 2.2.2.2
Tunnel Far End : n/a LSP Types : RSVP
Admin State : Up Oper State : Up
Signaling : TLDP Metric : 0
Acct. Pol : None Collect Stats : Disabled
Last Status Change : 08/12/2013 06:33:57 Adv. MTU Over. : No
Last Mgmt Change : 08/12/2013 06:32:47 VLAN VC Etype : 0x8100
Bw BookingFactor : 100 PBB Etype : 0x88e7
Oper Max BW(Kbps) : 0 Avail BW(Kbps) : 0
Net-Domain : default Egr Interfaces : Consistent
Flags : None
Mixed LSP Mode Information :
Mixed LSP Mode : Disabled Active LSP Type : RSVP
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Hello Timeout : 3 Unmatched Replies : 0
Max Drop Count : 3 Hold Down Time : 10
Tx Hello Msgs : 0 Rx Hello Msgs : 0
Src B-MAC LSB : 00-13 Ctrl PW VC ID : 550
The following show output indicates whether use-sdp-bmac is applied to a given PW.
A:bksim1613# show service id 550 sdp 1:550 detail
===============================================================================
Service Destination Point (Sdp Id : 1:550) Details
===============================================================================
-------------------------------------------------------------------------------
Sdp Id 1:550 -(2.2.2.2)
-------------------------------------------------------------------------------
Description : (Not Specified)
SDP Id : 1:550 Type : Spoke
Spoke Descr : (Not Specified)
VC Type : Ether VC Tag : n/a
Admin Path MTU : 0 Oper Path MTU : 1556
Delivery : MPLS
Far End : 2.2.2.2
Tunnel Far End : n/a LSP Types : RSVP
Hash Label : Disabled Hash Lbl Sig Cap : Disabled
Oper Hash Label : Disabled
Admin State : Up Oper State : Up
MinReqd SdpOperMTU : 1514
Adv Service MTU : n/a
Acct. Pol : None Collect Stats : Disabled
Ingress Label : 131048 Egress Label : 131063
Ingr Mac Fltr-Id : n/a Egr Mac Fltr-Id : n/a
Ingr IP Fltr-Id : n/a Egr IP Fltr-Id : n/a
Ingr IPv6 Fltr-Id : n/a Egr IPv6 Fltr-Id : n/a
Admin ControlWord : Not Preferred Oper ControlWord : False
Admin BW(Kbps) : 0 Oper BW(Kbps) : 0
Last Status Change : 08/12/2013 06:33:57 Signaling : TLDP
Last Mgmt Change : 08/12/2013 06:32:47 Force Vlan-Vc : Disabled
Endpoint : N/A Precedence : 4
PW Status Sig : Enabled
Class Fwding State : Down
Flags : None
Local Pw Bits : None
Peer Pw Bits : None
Peer Fault Ip : None
Peer Vccv CV Bits : lspPing
Peer Vccv CC Bits : mplsRouterAlertLabel
Application Profile: None
Transit Policy : None
Standby Sig Slave : False
Block On Peer Fault: False
Use sdp B-MAC : True
Ingress Qos Policy : (none) Egress Qos Policy : (none)
Ingress FP QGrp : (none) Egress Port QGrp : (none)
Ing FP QGrp Inst : (none) Egr Port QGrp Inst: (none)
KeepAlive Information :
Admin State : Disabled Oper State : Disabled
Hello Time : 10 Hello Msg Len : 0
Max Drop Count : 3 Hold Down Time : 10
Statistics :
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
I. Fwd. Octs. : 0 I. Dro. Octs. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
-------------------------------------------------------------------------------
Control Channel Status
-------------------------------------------------------------------------------
PW Status : disabled Refresh Timer : <none>
Peer Status Expire : false
Request Timer : <none>
Acknowledgement : false
-------------------------------------------------------------------------------
RSVP/Static LSPs
-------------------------------------------------------------------------------
Associated LSP List :
Lsp Name : to-bksim1611-1
Admin State : Up Oper State : Up
Time Since Last Tr*: 05h44m54s
-------------------------------------------------------------------------------
Class-based forwarding :
-------------------------------------------------------------------------------
Class forwarding : Disabled EnforceDSTELspFc : Disabled
Default LSP : Uknwn Multicast LSP : None
===============================================================================
FC Mapping Table
===============================================================================
FC Name LSP Name
-------------------------------------------------------------------------------
No FC Mappings
-------------------------------------------------------------------------------
Number of SDPs : 1
-------------------------------------------------------------------------------
===============================================================================
* indicates that the corresponding row element may have been truncated.
Label |
Description |
---|---|
SDP Id |
Displays the SDP identifier. |
Description |
Displays a text string describing the SDP. |
Admin Path MTU |
Displays the desired largest service frame size (in octets) that can be transmitted through this SDP to the far-end ESR, without requiring the packet to be fragmented. The default value of zero indicates that the path MTU should be computed dynamically from the corresponding MTU of the tunnel. |
Opr Path MTU |
Displays the actual largest service frame size (in octets) that can be transmitted through this SDP to the far-end ESR, without requiring the packet to be fragmented. In order to be able to bind this SDP to a given service, the value of this object minus the control word size (if applicable) must be equal to or larger than the MTU of the service, as defined by its service MTU. |
Far End |
Displays the far end IP address. |
Local End |
Displays the local end IP address. |
Delivery |
Displays the type of delivery used by the SDP: GRE or MPLS. |
IP address |
Displays the IP address of the remote end of the GRE or MPLS tunnel defined by this SDP. |
Adm Admin State |
Displays the desired state of the SDP. |
Opr Oper State |
Displays the operating state of the SDP. |
Flags |
Displays all the conditions that affect the operating status of this SDP. |
Signal Signaling |
Displays the signaling protocol used to obtain the ingress and egress labels used in frames transmitted and received on the SDP. |
Last Status Change |
Displays the time of the most recent operating status change to this SDP. |
Adv. MTU Over |
Specifies whether the advertised MTU of a VLL spoke SDP bind includes the 14-byte Layer 2 header. |
Last Mgmt Change |
Displays the time of the most recent management-initiated change to this SDP. |
KeepAlive Information |
Displays Keepalive information. |
Hello Time |
Displays how often the SDP echo request messages are transmitted on this SDP. |
Hello Msg Len |
Displays the length of the SDP echo request messages transmitted on this SDP. |
Hello Timeout |
Displays the number of seconds to wait for an SDP echo response message before declaring a timeout. |
Unmatched Replies |
Displays the number of SDP unmatched message replies timer expired. |
Max Drop Count |
The maximum number of consecutive SDP echo request messages that can be unacknowledged before the keepalive protocol reports a fault. |
Hold Down Time |
The amount of time to wait before the keepalive operating status is eligible to enter the alive state. |
TX Hello Msgs |
The number of SDP echo request messages transmitted since the keepalive was administratively enabled or the counter was cleared. |
Rx Hello Msgs |
The number of SDP echo request messages received since the keepalive was administratively enabled or the counter was cleared. |
Associated LSP List |
When the SDP type is MPLS, a list of LSPs used to reach the far-end router displays. All the LSPs in the list must terminate at the IP address specified in the far end field. If the SDP type is GRE, the following message displays: SDP Delivery Mechanism is not MPLS. |
Lsp Name |
Displays the LSP name. |
Time Since Last Transaction |
Displays the time of the last transaction. |
Signaling |
Displays the signaling type. |
Collect Stats |
Specifies whether the agent collects accounting statistics for this SDP. When the value is true the agent collects accounting statistics on this SDP. |
VLAN VC Etype |
Displays the VLAN VC type. |
BW Booking Factor |
Displays the value used to calculate the max SDP available bandwidth. The value specifies the percentage of the SDP max available bandwidth for VLL call admission. When the value of is set to zero (0), no new VLL spoke SDP bindings with non-zero bandwidth are permitted with this SDP. Overbooking, >100% is allowed. |
PBB Etype |
Displays the Ethertype used in frames sent out on this SDP when specified as vlan for Provider Backbone Bridging frames. |
Oper Max BW (kb/s) |
Displays the operational bandwidth in kilobits per seconds (kb/s) available for this SDP. The value is determined by the sum of the bandwidth of all the RSVP LSPs used by the SDP. |
Avail BW (kb/s) |
Displays the bandwidth that is still free for booking by the SDP bindings on the SDP. |
Net-Domain |
Displays the network-domain name configured on this SDP. The default value of this object is the default network-domain. |
Egr Interface |
Indicates whether all the egress network interfaces that can carry traffic on this SDP are associated with the network-domain configured on this SDP. not applicable: Indicates that there is no egress network interface that can carry traffic on this SDP. consistent: Indicates that the network-domains for all the egress network interfaces that can carry traffic on this SDP are consistent. inconsistent: Indicates that the network-domain for one or more egress network interfaces that can carry traffic on this SDP are inconsistent. |
Revert Time |
Specifies the time to wait before reverting back from LDP to the configured LSPs, after having failed over to LDP. |
Revert Count Down |
Indicates the timer countdown before reverting back from LDP on this SDP. The timer countdown begins after the first configured LSP becomes active. |
Flags |
Displays all the conditions that affect the operating status of this SDP. |
Class Forwarding |
Indicates the admin state of class-based forwarding on this SDP. When the value is true, class-based forwarding is enabled. |
EnforceDSTELspFc |
Specifies whether service manager must validate with RSVP the support of the FC by the LSP. |
Default LSP |
Specifies the LSP ID that is used as a default when class-based forwarding is enabled on this SDP. This object must be set when enabling class-based forwarding. |
Multicast LSP |
Displays the LSP ID that all multicast traffic will be forwarded on when class-based forwarding is enabled on this SDP. When this object has its default value, multicast traffic will be forwarded on an LSP according to its forwarding class mapping. |
Number of SDPs |
Displays the metric to be used within the Tunnel Table Manager for decision making purposes. When multiple SDPs going to the same destination exist, this value is used as a tie-breaker by Tunnel Table Manager users like MP-BGP to select route with lower value. |
sdp
Syntax
sdp sdp-id keep-alive
sdp sdp-id pw-port sdp-id
Context
[Tree] (clear>service>statistics sdp)
Full Context
clear service statistics sdp
Description
This command clears keep-alive statistics associated with the SDP ID.
Parameters
- sdp-id
-
The SDP ID for which to clear keepalive statistics.
- keep-alive
-
Clears keep-alive information associated with the SDP ID. The keep-alive history is not cleared.
Platforms
All
sdp
Syntax
sdp [sdp-id[:vc-id]] [ level level] [primary-vlan-enabled vlan-id]
Context
[Tree] (show>eth-cfm>mip-instantiation sdp)
Full Context
show eth-cfm mip-instantiation sdp
Description
This command displays MIP creation information for SDP bindings.
Parameters
- sdp-id
-
Specifies the value identifying the SDP.
- vc-id
-
Specifies the value identifying the virtual circuit identifier.
- level
-
Displays the MD level of the maintenance point.
- vlan-id
-
Specifies the Dot1Q VLAN ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
sdp
Syntax
sdp sdp-id:vc-id [test-service-id service-id] start
sdp sdp-id:vc-id stop
Context
[Tree] (tools>perform>service>id>admin-lock>pw sdp)
Full Context
tools perform service id admin-lock pw sdp
Description
This command specifies the spoke SDP binding to which an administrative lock will be applied for the MPLS-TP pseudowire. The administrative lock can be placed on a spoke SDP that is bound to a VLL SAP, another spoke SDP or a VPLS interface. Once the pseudowire is locked it may be put into loopback mode. The command must be executed at both ends of the pseudowire or MS-PW represented by the spoke SDP. Test traffic can then be injected using a configured test SAP on an Epipe, Apipe or Cpipe.
Parameters
- sdp-id:vc-id
-
Specifies the SDP-ID and VC-ID.
- test-service-id
-
Keyword that specifies the ID of a test service (SAP) to which the SDP is bound.
Platforms
All
sdp
Syntax
sdp sdp-id:vc-id start mode [mac-swap] [mac ieee-address] [all]
sdp sdp-id:vc-id stop
Context
[Tree] (tools>perform>service>id>loopback>eth sdp)
Full Context
tools perform service id loopback eth sdp
Description
This command places the specific MPLS SDP binding in loopback mode for reflecting Ethernet traffic back in the direction of the received stream. This is only applicable to MPLS SDP Bindings.
Parameters
- sdp-id:vc-id
-
Specifies the SDP ID and VC-ID.
- start mode
-
Specifies the loopback in relation to the MPLS SDP Binding.
- stop
-
Keyword that removes the MPLS SD-binding from loopback mode.
- mac-swap
-
Enable source address and destination address swapping for the reflected packets when the arriving packet is unicast. Any broadcast and multicast packets arriving on a looped point will be dropped.
- mac ieee-address
-
Optionally configure the source MAC address used in the reflected packet when the arriving packet is a broadcast or multicast. This does not apply to arriving unicast packets.
- all
-
Configured ieee-address is used as the source address for all reflected packets regardless of the arriving destination.
- mac-swap
-
No swapping of MAC addresses are performed without specifying this option and any non-unicast destined packets will not be reflected back to the source.
Platforms
All
sdp
Syntax
sdp sdp-id:vc-id {start | stop}
Context
[Tree] (tools>perform>service>id>loopback>pw sdp)
Full Context
tools perform service id loopback pw sdp
Description
This command places or removes the specified MPLS-TP SDP binding in loopback mode for the purpose of an MPLS-TP pseudowire test service.
The loopback is created at the PW level so everything under the PW label is looped back. It is recommended to configure an administrative lock for the MPLS-TP pseudowire for the specified test service prior to configuring the loopback.
Parameters
- sdp-id:vc-id
-
Specifies the SDP-ID and VC-ID.
- start
-
Keyword that places the specified MPLS-TP PW in loopback mode for the purpose of an MPLS_TP PW test service.
- stop
-
Keyword that removes the SDP binding from the loopback mode for the MPLS-TP pseudowire test service.
Platforms
All
sdp
Syntax
sdp {sdp-id [:vc-id] | far-end ip-address} [interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor>service>id sdp)
Full Context
monitor service id sdp
Description
This command monitors statistics for an SDP binding associated with this service.
Parameters
- sdp-id
-
Specifies the SDP identifier.
- ip-address
-
Specifies the system address of the far-end router for the SDP in dotted decimal notation. The string may be up to 32 characters.
- seconds
-
Configures the interval for each display, in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays absolute rate-per-second value for each statistic.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
All
Output
The following output is an example of SDP information.
Output ExampleA:ALA-12# monitor service id 100 sdp 10 repeat 3
===============================================================================
Monitor statistics for Service 100 SDP binding 10
===============================================================================
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
-------------------------------------------------------------------------------
At time t = 11 sec (Mode: Delta)
-------------------------------------------------------------------------------
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
-------------------------------------------------------------------------------
At time t = 22 sec (Mode: Delta)
-------------------------------------------------------------------------------
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
-------------------------------------------------------------------------------
At time t = 33 sec (Mode: Delta)
-------------------------------------------------------------------------------
I. Fwd. Pkts. : 0 I. Dro. Pkts. : 0
E. Fwd. Pkts. : 0 E. Fwd. Octets : 0
===============================================================================
A:ALA-12#
sdp-group
sdp-group
Syntax
sdp-group [group-name]
Context
[Tree] (show>service sdp-group)
Full Context
show service sdp-group
Description
This show command will display the SDPs and the PW templates that are associated with the group-name.
Platforms
All
Output
The following output is an example of SDP group information.
Output Example*A:Dut-B# show service sdp-group
==================================================
SDP Group Information
==================================================
Group Value
--------------------------------------------------
red 1
blue 2
--------------------------------------------------
Entries found: 2
==================================================
*A:Dut-B#
*A:Dut-B# show service sdp-group "red"
=======================================================================
SDP-Group Information
=======================================================================
Name : red Value : 1
Associated SDPs
=======================================================================
SdpId : 204 Sdp-Group : red
SdpId : 205 Sdp-Group : red
-----------------------------------------------------------------------
Number of Entries: 2
=======================================================================
Associated pw-template included
=======================================================================
Pw-Template : 1 Sdp-Group : red
-----------------------------------------------------------------------
Number of Entries: 1
=======================================================================
Associated pw-template excluded
=======================================================================
No Entries found
=======================================================================
*A:Dut-B#
sdp-group-using
sdp-group-using
Syntax
sdp-group-using
Context
[Tree] (show>service sdp-group-using)
Full Context
show service sdp-group-using
Description
This command displays groups using SDP.
Platforms
All
Output
The following output is an example of information pertaining to objects using SDP groups.
Output Example*A:Dut-D# show service sdp-group-using
=======================================================================
SDP-Group Information
=======================================================================
SdpId : 402 Sdp-Group : red
SdpId : 405 Sdp-Group : red
SdpId : 4021 Sdp-Group : blue
SdpId : 4051 Sdp-Group : blue
Associated pw-template included
=======================================================================
Pw-Template : 1 Sdp-Group : red
Pw-Template : 2 Sdp-Group : blue
Associated pw-template excluded
=======================================================================
No Entries found
=======================================================================
*A:Dut-D#
sdp-using
sdp-using
Syntax
sdp-using etree
sdp-using node-id node-id [global-id global-id]
sdp-using aarp aarpID
sdp-using app-profile app-profile-name
sdp-using far-end {ip-address | ipv6-address}
sdp-using [sdp-id[:vc-id]]
sdp-using transit-policy ip transit-ip-policy
sdp-using transit-policy prefix transit-prefix-policy
Context
[Tree] (show>service sdp-using)
Full Context
show service sdp-using
Description
This command displays services using SDP or far-end address options.
Parameters
- node-id
-
Specifies the node ID.
- global-id
-
Specifies the global ID.
- aarpID
-
Specifies the AARP instance ID.
- app-profile-name
-
32 characters max.
- sdp-id
-
Displays only services bound to the specified SDP ID.
- vc-id
-
The virtual circuit identifier.
- ip-address
-
Displays only services matching with the specified far-end IP address. 64 characters maximum.
- ipv6-address
-
Displays only services matching with the specified far-end IPv6 address. 64 characters maximum.
- transit-ip-policy
-
Specifies a transit IP policy ID.
- transit-prefix-policy
-
Specifies a transit prefix policy ID.
Platforms
All
Output
The following output is an example of SDP using information, and Show Service SDP Using Output Fields describes the output fields.
Output Example*A:ALA-1# show service sdp-using 300
===============================================================================
Service Destination Point (Sdp Id : 300)
===============================================================================
SvcId SdpId Type Far End Opr State I.Label E.Label
-------------------------------------------------------------------------------
1 300:1 Mesh 10.0.0.13 Up 131071 131071
2 300:2 Spok 10.0.0.13 Up 131070 131070
100 300:100 Mesh 10.0.0.13 Up 131069 131069
101 300:101 Mesh 10.0.0.13 Up 131068 131068
102 300:102 Mesh 10.0.0.13 Up 131067 131067
-------------------------------------------------------------------------------
Number of SDPs : 5
-------------------------------------------------------------------------------
*A:ALA-1#
The following output is an example of VPLS E-Tree configured SDP bindings.
*A:DutA# show service sdp-using etree
===========================================================================
Etree SDP-BIND Information
===========================================================================
Svc Id SDP-BIND Information Type Root- Leaf-Ac
leaf-tag
---------------------------------------------------------------------------
2005 12:2005 Spoke Enabled N/A
2005 12:2006 Spoke Disabled Enabled
2005 12:2007 Spoke Disabled Enabled
---------------------------------------------------------------------------
Number of etree sdp-binds: 3
===========================================================================
Label |
Description |
---|---|
Svc ID |
The service identifier. |
Sdp ID |
The SDP identifier. |
Type |
Type of SDP: spoke or mesh. |
Far End |
The far end address of the SDP. |
Oper State |
The operational state of the service. |
Ingress Label |
The label used by the far-end device to send packets to this device in this service by this SDP. |
Egress Label |
The label used by this device to send packets to the far-end device in this service by this SDP. |
Etree SDP Bind Information |
|
Svc ID |
The service identifier. |
SDP-Bind |
The leaf tag SDP bind identifier. |
Type |
The type SDP bind. |
Root-Leaf-Tag |
The state of the root leaf tag SDP bind, |
Leaf-AC |
The state of the leaf AC SDP bind. |
seamless-bfd
seamless-bfd
Syntax
seamless-bfd
Context
[Tree] (show>router>bfd seamless-bfd)
Full Context
show router bfd seamless-bfd
Description
This command displays Seamless-BFD information.
Platforms
All
seamless-bfd
Syntax
seamless-bfd
Context
[Tree] (clear>router>bfd seamless-bfd)
Full Context
clear router bfd seamless-bfd
Description
Commands in this context clear Seamless-BFD session and statistics information.
Platforms
All
secure-boot
secure-boot
Syntax
secure-boot
Context
[Tree] (tools>dump>system>security secure-boot)
Full Context
tools dump system security secure-boot
Description
This command displays secure boot settings.
Platforms
7750 SR-1-24D, 7750 SR-1-46S, 7750 SR-1-48D, 7750 SR-1-92S, 7750 SR-1x-48D, 7750 SR-1x-92S, 7750 SR-s, 7950 XRS-20e
security
security
Syntax
security
Context
[Tree] (show>system security)
Full Context
show system security
Description
Commands in this context display security configuration information.
Platforms
All
security
Syntax
security
Context
[Tree] (tools>dump security)
Full Context
tools dump security
Description
Commands in this context dump tools for security.
Platforms
All
security
Syntax
security
Context
[Tree] (tools>dump>system security)
Full Context
tools dump system security
Description
Commands in this context display tools for system security.
Platforms
7750 SR-1-24D, 7750 SR-1-46S, 7750 SR-1-48D, 7750 SR-1-92S, 7750 SR-1x-48D, 7750 SR-1x-92S, 7750 SR-s, 7950 XRS-20e
security
Syntax
security
Context
[Tree] (tools>perform security)
Full Context
tools perform security
Description
This command enables tools for testing security.
Platforms
All
security-policy
security-policy
Syntax
security-policy router [Base] [security-policy-id security-policy-id]
security-policy service service-id [security-policy-id security-policy-id]
Context
[Tree] (show>ipsec security-policy)
Full Context
show ipsec security-policy
Description
This command displays
Parameters
- service-id
-
Specifies the service-id of the tunnel delivery service.
- security-policy-id
-
Specifies the IPsec security policy entry that this tunnel will use.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the show ipsec security-policy command.
Output Example*A:ALA-48>show>ipsec# security-policy 1
========================================================================
Security Policy Param Entries
========================================================================
SvcId Security Policy LocalIp RemoteIp
PlcyId ParamsId
------------------------------------------------------------------------
1 1 1 0.0.0.0/0 0.0.0.0/0
------------------------------------------------------------------------
No. of IPsec Security Policy Param Entries: 1
========================================================================
*A:ALA-48>show>ipsec#
seen-ip
seen-ip
Syntax
seen-ip transit-ip-policy ip-policy-id
seen-ip transit-ip-policy ip-policy-id clear
Context
[Tree] (tools>dump>app-assure seen-ip)
Full Context
tools dump application-assurance seen-ip
Description
This command dumps application-assurance seen-ip information for a specified transit-ip policy.
Parameters
- ip-policy-id
-
An integer that identifies a transit IP profile entry.
- clear
-
Clears the seen IP information after reading.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
segment-routing
segment-routing
Syntax
segment-routing
Context
[Tree] (clear>router segment-routing)
Full Context
clear router segment-routing
Description
Commands in this context clear segment routing statistics.
Platforms
All
segment-routing
Syntax
segment-routing
Context
[Tree] (show>router segment-routing)
Full Context
show router segment-routing
Description
Commands in this context display segment routing information.
Platforms
All
segment-routing
Syntax
segment-routing
Context
[Tree] (tools>dump>router segment-routing)
Full Context
tools dump router segment-routing
Description
Commands in this context display segment routing information.
Platforms
All
segment-routing
Syntax
segment-routing
Context
[Tree] (monitor>router segment-routing)
Full Context
monitor router segment-routing
Description
Commands in this context monitor Segment Routing Statistics.
Platforms
All
segment-routing-v6
segment-routing-v6
Syntax
segment-routing-v6 [summary]
Context
[Tree] (show>router segment-routing-v6)
Full Context
show router segment-routing-v6
Description
Commands in this context display SRv6 information.
Parameters
- summary
-
Displays information in a summarized format.
Platforms
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
Output
Use the following command to display SRv6 information.
show router segment-routing-v6 summary
Output Example
===============================================================================
Segment Routing v6
===============================================================================
Origination FPE : 1
Source IPv6 Address :
-------------------------------------------------------------------------------
Micro Segment
-------------------------------------------------------------------------------
Block Length : 48 bits
Global Entries : 12 (16384 uNs)
SID Length : 16 bits
===============================================================================
Locator Admin State
Prefix
-------------------------------------------------------------------------------
C1 Up
3333:3:3:3::/64
-------------------------------------------------------------------------------
Locators : 1
-------------------------------------------------------------------------------
===============================================================================
Micro Segment Locator Admin/Oper St
Prefix
-------------------------------------------------------------------------------
msl1 Up/Up
3333:3:3:3::/64
-------------------------------------------------------------------------------
Micro Segment Locators : 1
-------------------------------------------------------------------------------
===============================================================================
segment-routing-v6
Syntax
segment-routing-v6
Context
[Tree] (show>router>isis segment-routing-v6)
Full Context
show router isis segment-routing-v6
Description
Commands in this context display IS-IS SRv6 information.
Platforms
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
segment-routing-v6
Syntax
segment-routing-v6 [ip-address]
Context
[Tree] (show>service segment-routing-v6)
Full Context
show service segment-routing-v6
Description
This command displays SRv6 information.
Parameters
- ip-address
-
Specifies the IP address.
Platforms
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
segment-routing-v6
Syntax
segment-routing-v6 [instance instance] [locator locator-name] [end-dt4] [end-dt6] [end-dt46] [end-dx2] [end-dt2u] [end-dt2m]
segment-routing-v6 detail
segment-routing-v6 [instance instance] destinations
segment-routing-v6 [instance instance] esi esi
segment-routing-v6 [instance instance] micro [micro-segment-locator ms-locator-name] [udx2] [udt2m] [udt2u] [udt4] [udt6] [udt46]
Context
[Tree] (show>service>id segment-routing-v6)
Full Context
show service id segment-routing-v6
Description
This command displays SRv6 service information.
Parameters
- instance
-
Specifies the instance ID for display.
- locator-name
-
Specifies the locator name for display, up to 64 characters.
- end-dt4
-
Displays the End.DT4 function associated with the SRv6 instance in the service.
- end-dt6
-
Displays the End.DT6 function associated with the SRv6 instance in the service.
- end-dt46
-
Displays the End.DT46 function associated with the SRv6 instance in the service.
- end-dx2
-
Displays the End.DX2 function associated with the SRv6 instance in the service.
- end-dt2u
-
Displays the End.DT2U function associated with the SRv6 instance in the service.
- end-dt2m
-
Displays the End.DT2M function associated with the SRv6 instance in the service.
- destinations
-
Specifies that all destinations for display are included.
- esi
-
Specifies a 10-byte ESI by which to filter the displayed information. For example,ESI-0 | ESI-MAX or 00-11-22-33-44-55-66-77-88-99 with any of these separators ('-',':',' ').
- ms-locator-name
-
Specifies the micro-segment locator name for display, up to 64 characters.
- udt4
-
Displays the uDT4 function associated with the SRv6 instance in the service.
- udt6
-
Displays the uDT6 function associated with the SRv6 instance in the service.
- udt46
-
Displays the uDT46 function associated with the SRv6 instance in the service.
- udx2
-
Displays the uDX2 function associated with the SRv6 instance in the service.
- udt2u
-
Displays the uDT2U function associated with the SRv6 instance in the service.
- udt2m
-
Displays the uDT2M function associated with the SRv6 instance in the service.
Platforms
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
Output
Output ExampleSRv6 instance Field Descriptions describes the SRv6 instance field descriptions.
Use the following command to display SRv6 instance and destination information.
show service id "bd-1900-srv6" segment-routing-v6 instance 1 destinations
===============================================================================
TEP, SID (Instance 1)
===============================================================================
TEP Address Segment Id Oper Mcast Num
State MACs
-------------------------------------------------------------------------------
192.0.2.3 cafe:1:0:3:7b1c:9000:: Up BUM 0
192.0.2.4 cafe:1:0:4:7:b1ca:: Up BUM 0
192.0.2.5 cafe:1:0:5:7b1c:e000:: Up BUM 0
192.0.2.5 cafe:1:0:5:7b1c:f000:: Up - 1
-------------------------------------------------------------------------------
Number of TEP, SID: 4
-------------------------------------------------------------------------------
===============================================================================
===============================================================================
Segment Routing v6 Ethernet Segment Dest (Instance 1)
===============================================================================
Eth SegId Num. Macs Last Update
-------------------------------------------------------------------------------
show service id "bd-1900-srv6" segment-routing-v6 instance 1 destinations detail
===============================================================================
TEP, SID (Instance 1)
===============================================================================
TEP Address Segment Id Oper Mcast Num
State MACs
-------------------------------------------------------------------------------
192.0.2.3 cafe:1:0:3:7b1c:9000:: Up BUM 0
Oper Flags : None
Sup BCast Domain : No
Last Update : 02/23/2023 11:12:29
192.0.2.4 cafe:1:0:4:7:b1ca:: Up BUM 0
Oper Flags : None
Sup BCast Domain : No
Last Update : 02/23/2023 11:12:29
192.0.2.5 cafe:1:0:5:7b1c:e000:: Up BUM 0
Oper Flags : None
Sup BCast Domain : No
Last Update : 02/23/2023 11:12:29
192.0.2.5 cafe:1:0:5:7b1c:f000:: Up - 1
Oper Flags : None
Sup BCast Domain : No
Last Update : 02/23/2023 11:12:29
-------------------------------------------------------------------------------
Number of TEP, SID: 4
-------------------------------------------------------------------------------
===============================================================================
===============================================================================
Segment Routing v6 Ethernet Segment Dest (Instance 1)
===============================================================================
Eth SegId Num. Macs Last Update
-------------------------------------------------------------------------------
Field |
Description |
---|---|
Locator |
The locator name |
Type |
The type |
Function |
The function |
SID |
The segment ID |
Status |
The status |
Instance |
The instance |
Mcast |
The multicast value |
TEP Address |
The tunnel endpoint IP address |
Segment Id |
The segment ID |
L2 PBR |
The layer 2 policy based routing value |
EvpnStatic |
The EVPN static value |
SupBcasDom |
The Sup BCast Domain value |
Num MACs |
The number of MACs |
Number of TEP, SID |
The total number of TEP and SIDs |
No Matching Entries |
The number of matching entries |
selective-fib-log
selective-fib-log
Syntax
selective-fib-log
Context
[Tree] (tools>dump>router selective-fib-log)
Full Context
tools dump router selective-fib-log
Description
This command configures the dump tools for selective FIB log information for a specific IOM.
Platforms
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS
Output
The following output is an example of selective FIB log information.
Output Example*A:Dut-C# /tools dump router selective-fib-log
1 : 2020/01/08 13:32:59.100 : Creating Base router
2 : 2020/01/08 13:32:59.101 : Adding port system to if=system Base router
2 : 2020/01/08 13:32:59.103 : Creating management router
3 : 2020/01/08 13:32:59.103 : Creating vpls-management instance
4 : 2020/01/08 13:32:59.103 : Adding port A/1 to if=management management router
4 : 2020/01/08 13:40:55.404 : Adding port 1/1/5 to if=ip-10.10.5.5 Base router
4 : 2020/01/08 13:40:55.407 : Adding port 2/1/6 to if=ip-10.10.7.7 Base router
4 : 2020/01/08 13:40:55.411 : Adding port 2/1/2 to if=ip-10.10.11.11 Base router
4 : 2020/01/08 13:40:55.414 : Adding port 2/1/2 to if=ip-10.10.13.13 Base router
4 : 2020/01/08 13:40:55.417 : Adding port 2/1/2 to if=ip-10.10.15.15 Base router
4 : 2020/01/08 13:40:55.420 : Adding port 1/1/1 to if=ip-10.10.17.18 Base router
4 : 2020/01/08 13:40:55.423 : Adding port 1/1/3 to if=ip-10.10.21.22 Base router
4 : 2020/01/08 13:40:55.427 : Adding port 2/1/3 to if=ip-10.10.23.24 Base router
4 : 2020/01/08 13:40:55.430 : Adding port 2/1/4 to if=ip-10.10.25.26 Base router
4 : 2020/01/08 13:40:55.433 : Adding port 1/1/2 to if=ip-10.10.27.28 Base router
4 : 2020/01/08 13:40:55.436 : Adding port 2/1/1 to if=ip-10.10.31.31 Base router
4 : 2020/01/08 13:40:55.440 : Adding port 3/1/3 to if=ip-10.10.39.40 Base router
4 : 2020/01/08 13:40:55.443 : Adding port 3/1/1 to if=ip-10.10.43.44 Base router
4 : 2020/01/08 13:40:55.446 : Adding port 3/1/2 to if=ip-10.10.45.45 Base router
4 : 2020/01/08 13:40:55.449 : Adding port 2/2/2 to if=ip-10.10.47.47 Base router
4 : 2020/01/08 13:40:55.453 : Adding port 2/2/1 to if=ip-10.10.49.49 Base router
4 : 2020/01/08 13:40:55.456 : Adding port 1/1/4 to if=ip-10.10.61.61 Base router
4 : 2020/01/08 13:40:55.459 : Adding port 2/1/5 to if=ip-10.10.63.63 Base router
4 : 2020/01/08 13:40:55.465 : Creating router 10105151
5 : 2020/01/08 13:40:55.470 : Adding port 1/2/1 to if=vprn-10.10.51.51 router 10105151
5 : 2020/01/08 13:40:55.475 : Creating router 10105152
6 : 2020/01/08 13:40:55.480 : Adding port 1/2/2 to if=vprn-10.10.51.52 router 10105152
6 : 2020/01/08 13:41:10.678 : Removing port 1/1/4 from if=ip-10.10.61.61 Base router
6 : 2020/01/08 13:41:10.681 : Removing port 1/2/1 from if=vprn-10.10.51.51 router 10105151
6 : 2020/01/08 13:41:10.684 : Removing port 1/2/2 from if=vprn-10.10.51.52 router 10105152
6 : 2020/01/08 13:41:10.690 : Removing port 2/1/2 from if=ip-10.10.11.11 Base router
6 : 2020/01/08 13:41:10.692 : Removing port 2/1/2 from if=ip-10.10.15.15 Base router
6 : 2020/01/08 13:41:10.693 : Removing port 2/1/2 from if=ip-10.10.13.13 Base router
6 : 2020/01/08 13:41:10.698 : Removing port 2/1/5 from if=ip-10.10.63.63 Base router
6 : 2020/01/08 13:41:10.711 : Removing port 1/1/1 from if=ip-10.10.17.18 Base router
6 : 2020/01/08 13:41:10.713 : Removing port 1/1/3 from if=ip-10.10.21.22 Base router
6 : 2020/01/08 13:41:10.715 : Removing port 2/1/3 from if=ip-10.10.23.24 Base router
6 : 2020/01/08 13:41:10.717 : Removing port 2/1/4 from if=ip-10.10.25.26 Base router
6 : 2020/01/08 13:41:10.720 : Removing port 1/1/2 from if=ip-10.10.27.28 Base router
6 : 2020/01/08 13:41:10.722 : Removing port 2/1/1 from if=ip-10.10.31.31 Base router
6 : 2020/01/08 13:41:10.724 : Removing port 3/1/3 from if=ip-10.10.39.40 Base router
6 : 2020/01/08 13:41:10.727 : Removing port 3/1/1 from if=ip-10.10.43.44 Base router
6 : 2020/01/08 13:41:10.729 : Removing port 3/1/2 from if=ip-10.10.45.45 Base router
6 : 2020/01/08 13:41:10.731 : Removing port 2/2/2 from if=ip-10.10.47.47 Base router
6 : 2020/01/08 13:41:10.733 : Removing port 2/2/1 from if=ip-10.10.49.49 Base router
6 : 2020/01/08 13:41:10.735 : Removing port 1/1/5 from if=ip-10.10.5.5 Base router
6 : 2020/01/08 13:41:10.741 : Removing port 2/1/6 from if=ip-10.10.7.7 Base router
6 : 2020/01/08 13:41:10.751 : Deleting router 10105151
6 : 2020/01/08 13:41:10.756 : Deleting router 10105152
6 : 2020/01/08 13:41:15.713 : Adding port 1/1/4 to if=to_Ixia3 Base router
6 : 2020/01/08 13:41:15.723 : Adding port 2/1/5 to if=to_Ixia.24 Base router
6 : 2020/01/08 13:41:22.170 : Removing port 1/1/4 from if=to_Ixia3 Base router
6 : 2020/01/08 13:41:22.176 : Removing port 2/1/5 from if=to_Ixia.24 Base router
6 : 2020/01/08 13:58:37.666 : Enable system selective-fib
7 : 2020/01/08 13:59:17.668 : Creating router 1
8 : 2020/01/08 13:59:17.669 : Setting vrf-target on router 1
8 : 2020/01/08 13:59:17.670 : Enable auto-bind-tunnel for router 1
8 : 2020/01/08 13:59:17.676 : Adding port 1/1/2 to if=to_Dut-B router 1
9 : 2020/01/08 14:01:17.851 : Setting disable-selective-fib for router 1
10 : 2020/01/08 14:03:58.104 : Disable system selective-fib
11 : 2020/01/08 14:07:59.686 : Removing port 1/1/2 from if=to_Dut-B router 1
11 : 2020/01/08 14:07:59.699 : Deleting router 1
*A:Dut-C#
send-force-renew
send-force-renew
Syntax
send-force-renew ip-address
Context
[Tree] (tools>perform>router>dhcp>server send-force-renew)
Full Context
tools perform router dhcp local-dhcp-server send-force-renew
Description
This command sends a DHCP FORCERENEW message on behalf of the DHCP server to the DHCP client with specified IP address. A DHCP lease with the specified IP address must exist in the DHCP server.
Parameters
- ip-address
-
Specifies the DHCP client’s IP address in dotted notation a.b.c.d.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
sensor-group
sensor-group
Syntax
sensor-group name
sensor-group
Context
[Tree] (show>system>telemetry sensor-group)
Full Context
show system telemetry sensor-group
Description
This command displays the sensor group information.
Parameters
- name
-
Specifies the sensor group name, up to 32 characters.
Platforms
All
Output
The following output is an example of telemetry sensor group information and Show Sensor Group Field Descriptions describes the output fields.
Output Example# show system telemetry sensor-group
===============================================================================
Telemetry sensor-groups
===============================================================================
Name Valid Invalid
paths paths
-------------------------------------------------------------------------------
miro 1 0
-------------------------------------------------------------------------------
No. of Telemetry sensor-groups: 1
===============================================================================
Label |
Description |
---|---|
Name |
Displays the name of the telemetry sensor group name. |
Valid paths |
Displays the number of valid sensor group paths. |
Invalid paths |
Displays the number of invalid sensor group paths. |
No. of Telemetry sensor-groups |
Displays the total number of telemetry sensor groups. |
server
server
Syntax
server all
server capability
server prefix ip-prefix/prefix-length
server
Context
[Tree] (show>test-oam>twamp server)
Full Context
show test-oam twamp server
Description
This command displays TWAMP server information.
Parameters
- all
-
Displays all server information.
- ip-prefix/prefix-length
-
Specifies the IP address prefix of the TWAMP server.
- capability
-
Displays the modes referenced or supported by the TWAMP server, with an RFC reference where those modes are defined.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of TWAMP server information.
Output Example*A:ALA-48# show test-oam twamp server
==============================================================================
TWAMP Server (port 862)
==============================================================================
Admin State : Up Oper State : Up
Up Time : 0d 00:00:05
Curr Conn : 1 Max Conn : 32
ConnTimeout : 1800 Conn Reject : 2
Curr Sess : 2 Max Sess : 32
Tests Done : 5 Tests Rej : 0
Tests Abort : 0
TstPktsRx : 999 TstPktsTx : 999
==============================================================================
Prefix : 10.0.0.0/8
Tests Abort : 0
TstPktsRx : 999 TstPktsTx : 999
==============================================================================
Prefix : 10.0.0.0/8
Description : NMS-West
==============================================================================
Admin State : Up Oper State : Up
Curr Conn : 1 Max Conn : 32
Conn Reject : 0
Curr Sess : 2 Max Sess : 32
Tests Done : 5 Tests Rej : 0
Tests Abort : 0
TstPktsRx : 999 TstPktsTx : 999
------------------------------------------------------------------------------
Client Sessions Idle TstPktsRx TstPktsTx
Curr/Done/Rej/Abort
------------------------------------------------------------------------------
10.1.1.1 2/5/0/0 920 999 999
==============================================================================
==============================================================================
Prefix : 10.0.0.0/16
Description : NMS-West-Special
==============================================================================
Admin State : Up Oper State : Up
Curr Conn : 0 Max Conn : 32
Conn Reject : 0
Curr Sess : 0 Max Sess : 32
Tests Done : 0 Tests Rej : 0
Tests Abort : 0
TstPktsRx : 0 TstPktsTx : 0
------------------------------------------------------------------------------
Client Sessions Idle TstPktsRx TstPktsTx
Curr/Done/Rej/Abort
------------------------------------------------------------------------------
==============================================================================
*A:ALA-48# show test-oam twamp server capability
==============================================================================
TWAMP Server Supported Modes of Operation with RFC Reference
==============================================================================
Bit Value Description RFC
------------------------------------------------------------------------------
0 1 Unauthenticated 5357
4 16 Individual Session Control 5938
5 32 Reflect Octets Capability 6038
6 64 Symmetrical Size Sender Test Packet Format 6038
===============================================================================
server
Syntax
server
Context
[Tree] (clear>test-oam>twamp server)
Full Context
clear test-oam twamp server
Description
This command clears TWAMP server statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
server
Syntax
server
Context
[Tree] (tools>dump>test-oam>twamp server)
Full Context
tools dump test-oam twamp server
Description
This command dumps TWAMP server information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
server-stats
server-stats
Syntax
server-stats
Context
[Tree] (show>router>dhcp>server server-stats)
[Tree] (show>router>dhcp6>server server-stats)
Full Context
show router dhcp local-dhcp-server server-stats
show router dhcp6 local-dhcp-server server-stats
Description
This command displays DHCP or DHCP6 server statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of server statics information
Output Example*A:SUB-Dut-A# show router dhcp local-dhcp-server dhcpS1 server-stats
==============================================================================
Statistics for DHCP Server dhcpS1 router Base
==============================================================================
Rx Discover Packets : 0
Rx Request Packets : 0
Rx Release Packets : 0
Rx Decline Packets : 0
Rx Inform Packets : 0
Tx Offer Packets : 0
Tx Ack Packets : 0
Tx Nak Packets : 0
Tx Forcerenew Packets : 0
Client Ignored Offers : 0
Leases Timed Out : 0
Dropped Bad Packet : 0
Dropped Invalid Type : 0
Dropped No User Database : 0
Dropped Unknown Host : 0
Dropped User Not Allowed : 0
Dropped Lease Not Ready : 0
Dropped Lease Not Found : 0
Dropped Not Serving Pool : 0
Dropped Invalid User : 0
Dropped Overload : 0
Dropped Persistence Overload : 0
Dropped Generic Error : 0
Dropped Destined To Other : 0
Dropped Address Unavailable : 0
Dropped Max Leases Reached : 0
Dropped Server Shutdown : 0
Dropped No Subnet For Fixed IP: 0
==============================================================================
*A:SUB-Dut-A#
*A:cses-V26>show>router>dhcp6>server# server-stats
===============================================================================
Statistics for DHCPv6 Server test1 router Base
===============================================================================
Rx Solicit Packets : 0
Rx Request Packets : 0
Rx Confirm Packets : 0
Rx Renew Packets : 0
Rx Rebind Packets : 0
Rx Decline Packets : 0
Rx Release Packets : 0
Rx Information Request Packets: 0
Rx Leasequery Packets : 0
Tx Advertise Packets : 0
Tx Reply Packets : 0
Tx Reconfigure Packets : 0
Tx Leasequery Reply Packets : 0
Client Ignored Offers : 0
Leases Timed Out : 0
Dropped Bad Packet : 0
Dropped Invalid Type : 0
Dropped Lease Not Ready : 0
Dropped Not Serving Pool : 0
Dropped Overload : 0
Dropped Persistence Overload : 0
Dropped Generic Error : 0
Dropped Destined To Other : 0
Dropped Max Leases Reached : 0
Dropped Server Shutdown : 0
Dropped Leasequery Not Allowed: 0
Dropped Duplicate : 0
Dropped busy primary audit : 0
Rx Int. PPP SLAAC Requests : 0
Rx Int. IPoE SLAAC Requests : 0
Rx Int. IPoE WAN Requests : 0
Rx Int. IPsec : 0
Rx Internal Releases : 0
Dropped Internal w/Failover : 0
Dropped Internal w/Int-id-map : 0
Dropped Internal w/User-ident : 0
Dropped Internal w/Conflicts : 0
Failover statistics
-------------------------------------------------------------------------------
Dropped Invalid Packets : 0
Failover Shutdown : 0
Lease Already Expired : 0
Maximum Lease Count Reached : 0
Prefix Not Found : 0
Host Conflict : 0
Address Conflict : 0
Peer conflict : 0
Persistence congestion : 0
No Lease Hold Time Configured : 0
Invalid Prefix Length : 0
Lease Not Found : 0
===============================================================================
*A:cses-V26>show>router>dhcp6>server#
Server Stats Field Descriptions describes server stats show command output fields.
Field |
Description |
---|---|
RX Discover Packets |
The number of discover packets received by the DHCP server instance |
Rx Request Packets |
The number of request packets received by the DHCP server instance. |
Rx Release Packets |
The number of released packets received by the DHCP server instance |
Rx Decline Packets |
The number of declined packets received by the DHCP server instance |
Rx Inform Packets |
The number of inform packets received by the DHCP server instance |
Tx Offer Packets |
The number of offer packets sent by the DHCP server instance |
Tx Ack Packets |
The number of DHCP ACK packets sent by the DHCP server instance |
Tx Nak Packets |
The number of DHCP NAK packets sent by the DHCP server instance |
Tx Forcerenew Packets |
The number of DHCP force renew packets sent by the server instance |
Client Ignored Offers |
The number of DHCP offer packets sent by the DHCP server instance that were ignored by clients |
Leases Timed Out |
The number of leases timed out |
Dropped Bad Packet |
The number of dropped of DHCP packets received that were corrupt |
Dropped Invalid Type |
The number of DHCP packets received that had an invalid message type |
Dropped No User Database |
The number of DHCP packets dropped because the value of this server instance is not equal to the default value and a local user database with that name could not be found |
Dropped Unknown Host |
The number of DHCP packets dropped from hosts which were not found in the user database |
Dropped User Not Allowed |
The number of DHCP packets dropped from hosts which are found in the user database, but which have no address or pool specified |
Dropped Lease Not Ready |
The number of DHCP packets dropped by the server instance before the lease database was ready |
Dropped Lease Not Found |
The number of DHCP packets dropped by the server instance because no (valid) lease was found |
Dropped Not Serving Pool |
The number of DHCP packets dropped by the server instance because there were no more free addresses in the pool |
Dropped Invalid User |
The number of DHCP packets dropped by the server instance because the MAC address of the sender or the option 82 didn't match the host lease state |
Dropped Overload |
The number of DHCP packets dropped by the server instance because they were received more than the server instance can handle |
Dropped Persistence Overload |
The number of DHCP packets dropped by the server instance because they were received in more than the DHCP persistence system can handle. If this occurs, only releases and declines are still processed. |
Dropped Generic Error |
The number of DHCP packets dropped by the server instance because of a generic error |
Dropped Destined To Other |
The number of DHCP requests dropped by the server instance because the (broadcast) request was not destined to this server |
Dropped Address Unavailable |
The number of DHCP requests dropped by the server instance because the requested address is not available |
Dropped Max Leases Reached |
The number of DHCP packets dropped by the server instance because the maximum number of leases was reached |
Dropped Server Shutdown |
The number of DHCP packets dropped by the server instance during server instance shutdown |
Dropped No Subnet for Fixed IP |
The number of DHCP packets dropped by the server instance for user-db hosts with a fixed address because the subnet to which the address belongs is not configured |
server-stats
Syntax
server-stats
Context
[Tree] (clear>router>dhcp6>server server-stats)
[Tree] (clear>router>dhcp>server server-stats)
Full Context
clear router dhcp6 local-dhcp-server server-stats
clear router dhcp local-dhcp-server server-stats
Description
This command clears all local DHCP or DHCPv6server statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
server-tls-profile
server-tls-profile
Syntax
server-tls-profile [server-tls-profile]
server-tls-profile server-tls-profile association
Context
[Tree] (show system security tls server-tls-profile)
Full Context
show system security tls server-tls-profile
Description
This command displays TLS server profile information.
Parameters
- server-tls-profile
-
Specifies the name of a TLS server profile for which to display information, up to 32 characters.
Platforms
All
servers
servers
Syntax
servers
servers all
Context
[Tree] (show>router>dhcp6 servers)
[Tree] (show>router>dhcp servers)
Full Context
show router dhcp6 servers
show router dhcp servers
Description
This command lists the local DHCP or DHCP6 servers.
Parameters
- all
-
Displays a complete list of local DHCP or DHCP6 servers.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of local DHCP or DHCP6 server information.
Output Example*A:ALA-49>show>router>dhcp# servers
=================================================================
Overview of DHCP Servers
=================================================================
Active Leases: 0
Maximum Leases: 159744
Router Server Admin State
-----------------------------------------------------------------
Router: Base base_router_dhcp_server outOfService
Service: 3 s1 inService
=================================================================
*A:ALA-49>show>router>dhcp#
*A:cses-V26>show>router>dhcp6# servers
==================================================================
Overview of DHCP Servers
==================================================================
Active Leases: 0
Maximum Leases: 159744
Router Server Admin State
------------------------------------------------------------------
Router: Base dhcp6 inService
Router: Base test1 inService
Router: Base testtest outOfService
==================================================================
*A:cses-V26>show>router>dhcp6#
service
service
Syntax
service
Context
[Tree] (clear service)
Full Context
clear service
Description
Commands in this context clear services commands.
Platforms
All
service
Syntax
service
Context
[Tree] (show service)
Full Context
show service
Description
Commands in this context display services related information.
Platforms
All
service
service
Syntax
service service-id
Context
[Tree] (show>ipsec service)
Full Context
show ipsec service
Description
This command displays service specific IPsec configuration.
Parameters
- service-id
-
The VPRN service ID or service name.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the service command.
show ipsec service 100
Output Example
===============================================================================
Service-specific IPsec configurations
===============================================================================
Reverse Route Override: any-idi
===============================================================================
service
Syntax
service
Context
[Tree] (monitor service)
Full Context
monitor service
Description
Commands in this context configure criteria to monitor specific service SAP criteria.
Platforms
All
service
Syntax
service service-id [security-policy-id security-policy-id]
Context
[Tree] (show>ipsec>security-policy service)
Full Context
show ipsec security-policy service
Description
This command displays service security policy information.
Parameters
- service-id
-
Specifies the service ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
service-activation-testhead
service-activation-testhead
Syntax
service-activation-testhead
Context
[Tree] (show>test-oam service-activation-testhead)
Full Context
show test-oam service-activation-testhead
Description
Commands in this context display service activation testhead information.
The service-test command shows the results and configuration for one Y.1564 service activation test run.
The service-tests command shows a list of all available Y.1564 service activation tests.
Platforms
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS
service-activation-testhead
Syntax
service-activation-testhead service-test all
service-activation-testhead service-test name [ run run-number]
Context
[Tree] (clear>test-oam service-activation-testhead)
Full Context
clear test-oam service-activation-testhead
Description
This command clears the results of all previous executions for the specified service test.
Parameters
- all
-
Keyword used to specify the deletion of all reports.
- name
-
Specifies the service test name, up to 64 characters, for which to clear results.
- run
-
Specifies a particular instance of the service test for which to clear results.
Platforms
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS
service-name-using
service-name-using
Syntax
service-name-using [detail]
Context
[Tree] (show>service service-name-using)
Full Context
show service service-name-using
Description
This command displays the services defined on the system, ordered by name.
Parameters
- detail
-
This parameter displays all of the services configured on the system along with their descriptions and administrative and operational states.
Platforms
All
Output
The following shows an example of service name-using information.
Service Commands Service-Name-Using Field Descriptions describes the show command output fields.
Output Example*A:PE-1# show service service-name-using
===============================================================================
Services By Name
===============================================================================
Service Name Type Service Id
-------------------------------------------------------------------------------
server-3 Vprn 3
server-5 Vprn 5
server-7 Vprn 7
evi-16 Vpls 16
CE-31 Vprn 31
_tmnx_InternalIesService Ies 2147483648
_tmnx_InternalVplsService intV* 2147483649
-------------------------------------------------------------------------------
Matching Services : 7
===============================================================================
*A:PE-1#
*A:PE-1#
*A:PE-1# show service service-name-using detail
===============================================================================
Services By Name
===============================================================================
Service Name Type Service Id
-------------------------------------------------------------------------------
server-3 Vprn 3
Admin/Oper: Up/Up
Customer: 1
Description:
server-5 Vprn 5
Admin/Oper: Up/Up
Customer: 1
Description:
server-7 Vprn 7
Admin/Oper: Up/Up
Customer: 1
Description:
evi-16 Vpls 16
Admin/Oper: Up/Up
Customer: 1
Description:
CE-31 Vprn 31
Admin/Oper: Up/Up
Customer: 1
Description:
_tmnx_InternalIesService Ies 2147483648
Admin/Oper: Up/Down
Customer: 1
Description:
IES Service for internal purposes only
_tmnx_InternalVplsService intV* 2147483649
Admin/Oper: Up/Down
Customer: 1
Description:
VPLS Service for internal purposes only
-------------------------------------------------------------------------------
Matching Services : 7
===============================================================================
Label |
Description |
---|---|
Service Name |
Displays the name of the service. |
Type |
Displays the service type configured for the service ID. |
Service Id |
Displays the service identifier. |
service-test
service-test
Syntax
service-test service-test-name run run-number
Context
[Tree] (show>test-oam>sath service-test)
Full Context
show test-oam service-activation-testhead service-test
Description
This command displays the results and configuration for the specified Y.1564 service activation test run.
Parameters
- service-test-name
-
Specifies the service test name, up to 64 characters.
- run-number
-
Specifies a particular instance of the service test for which to display results.
Platforms
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS
Output
The following outputs are examples of service test configuration information, and Output fields: service-test describes the output fields:
Output example (service test still running)show test-oam service-activation-testhead service-test "10" run 10
-------------------------------------------------------------------------------
Y.1564 Results for Run 10
Service Test 10
-------------------------------------------------------------------------------
Description : Service_Test_10
Oper State : running
Start Time : 2021/05/07 16:32:17 UTC
End Time : N/A
Stream Run Type : parallel
Acct Policy : (Unspecified)
Acct Policy Status: none
Completion Notif'n: disabled
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Y.1564 Results for Stream 1 Run 10
Service Test 10
-------------------------------------------------------------------------------
Description : ST10_Service_Stream_1
Oper State : running
Source MEP : 100 MEP Domain : 10
MEP Assoc. : 10 Source SAP : 1/1/1:100
Source MAC : 84:69:91:c7:e7:1a Dest MAC : 20:e0:9c:e3:d5:8d
Pattern (Dec): 0 Pattern (Hex): 0x0
C-Tag Dot1p : 0 C-Tag DEI : false
S-Tag Dot1p : 0 S-Tag DEI : false
Frm Size Tmpl: 1500bytes
Frm Sequence : a Frame Size a : 1500 bytes
Frame Size b : 128 bytes Frame Size c : 256 bytes
Frame Size d : 512 bytes Frame Size e : 1024 bytes
Frame Size f : 1280 bytes Frame Size g : 1518 bytes
Frame Size h : 9212 bytes Frame Size u : 2000 bytes
Confg Tx CIR : 1000000 kbps Confg Tx PIR : 1100000 kbps
Acp Crit Tmpl: ACT-1
Test Types : CIR
Complet Notif: enabled
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Y.1564 Results for Stream 1 Run 10 Test Type CIR
Service Test 10
-------------------------------------------------------------------------------
Oper State : running
Test Duration: 10:20 (mm:ss) Time Left : 598 s
Start Time : 2021/05/07 16:32:18 UTC
End Time : N/A
Frms Injected: 1874571 Frms Received: 1874505
Min Delay : 36 us Min Delay Var: 0 us
Max Delay : 46 us Max Delay Var: 7 us
Avg Delay : 41 us Avg Delay Var: 3 us
-------------------------------------------------------------------------------
===============================================================================
Test Compliance Report
===============================================================================
Criteria Throughput(kbps) FLR (%) Delay (us) Delay Var (us)
-------------------------------------------------------------------------------
Acceptable 1000000 1.0000 200 200
Configured 1000000 1.0000 200 200
M-Factor 100000 N/A N/A N/A
Measured 1000155 0.0035 41 3
Result unknown unknown unknown unknown
===============================================================================
Output example (service test run complete)
show test-oam service-activation-testhead service-test "10" run 10
-------------------------------------------------------------------------------
Y.1564 Results for Run 10
Service Test 10
-------------------------------------------------------------------------------
Description : Service_Test_10
Oper State : passed
Start Time : 2021/05/07 16:32:17 UTC
End Time : 2021/05/07 16:42:40 UTC
Stream Run Type : parallel
Acct Policy : (Unspecified)
Acct Policy Status: none
Completion Notif'n: disabled
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Y.1564 Results for Stream 1 Run 10
Service Test 10
-------------------------------------------------------------------------------
Description : ST10_Service_Stream_1
Oper State : passed
Source MEP : 100 MEP Domain : 10
MEP Assoc. : 10 Source SAP : 1/1/1:100
Source MAC : 84:69:91:c7:e7:1a Dest MAC : 20:e0:9c:e3:d5:8d
Pattern (Dec): 0 Pattern (Hex): 0x0
C-Tag Dot1p : 0 C-Tag DEI : false
S-Tag Dot1p : 0 S-Tag DEI : false
Frm Size Tmpl: 1500bytes
Frm Sequence : a Frame Size a : 1500 bytes
Frame Size b : 128 bytes Frame Size c : 256 bytes
Frame Size d : 512 bytes Frame Size e : 1024 bytes
Frame Size f : 1280 bytes Frame Size g : 1518 bytes
Frame Size h : 9212 bytes Frame Size u : 2000 bytes
Confg Tx CIR : 1000000 kbps Confg Tx PIR : 1100000 kbps
Acp Crit Tmpl: ACT-1
Test Types : CIR
Complet Notif: enabled
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Y.1564 Results for Stream 1 Run 10 Test Type CIR
Service Test 10
-------------------------------------------------------------------------------
Oper State : passed
Test Duration: 10:20 (mm:ss) Time Left : 0 s
Start Time : 2021/05/07 16:32:18 UTC
End Time : 2021/05/07 16:42:38 UTC
Frms Injected: 51576053 Frms Received: 51575773
Min Delay : 34 us Min Delay Var: 0 us
Max Delay : 55 us Max Delay Var: 17 us
Avg Delay : 41 us Avg Delay Var: 3 us
-------------------------------------------------------------------------------
===============================================================================
Test Compliance Report
===============================================================================
Criteria Throughput(kbps) FLR (%) Delay (us) Delay Var (us)
-------------------------------------------------------------------------------
Acceptable 1000000 1.0000 200 200
Configured 1000000 1.0000 200 200
M-Factor 100000 N/A N/A N/A
Measured 999912 0.0005 41 3
Result pass pass pass pass
===============================================================================
Label |
Description |
---|---|
Description |
Displays the service test or service stream description |
Oper State |
running — the specified service test or service stream is running passed — the specified service test or service stream is complete and has passed |
Start Time |
Displays the date and time that the specified service test or service stream was started |
End Time |
Displays the date and time that the specified service test or service stream was completed |
Stream Run Type |
Sequential — the streams are run consecutively Parallel — the streams are run in parallel |
Acct Policy |
Displays the accounting policy |
Acct Policy Status |
Displays the accounting policy status |
Completion Notif’n |
disabled — the service test completion notification is disabled enabled — the service test completion notification is enabled |
Source MEP |
Displays the source MEP |
MEP Domain |
Displays the MEP domain |
MEP Assoc. |
Displays MEP associations |
Source SAP |
Displays the source SAP |
Source MAC |
Displays the source MAC address |
Dest MAC |
Displays the destination MAC address |
Pattern (Dec) |
Displays the data pattern, in decimal notation |
Pattern (Hex) |
Displays the data pattern, in hexidecimal notation |
C-Tag Dot1p |
Displays the C-tag dot1p priority value for the VLAN |
C-Tag DEI |
true — the C-tag DEI is enabled false — the C-tag DEI is disabled |
S-Tag Dot1p |
Displays the S-tag dot1p priority value for the VLAN |
S-Tag DEI |
true — the S-tag DEI is enabled false — the S-tag DEI is disabled |
Frm Size Tmpl |
Displays the frame size template, in bytes |
Frm Sequence |
Displays the frame sequence |
Frame Size a |
Displays the frame size, in bytes, for template a |
Frame Size b |
Displays the frame size, in bytes, for template b |
Frame Size c |
Displays the frame size, in bytes, for template c |
Frame Size d |
Displays the frame size, in bytes, for template d |
Frame Size e |
Displays the frame size, in bytes, for template e |
Frame Size f |
Displays the frame size, in bytes, for template f |
Frame Size g |
Displays the frame size, in bytes, for template g |
Frame Size h |
Displays the frame size, in bytes, for template h |
Frame Size u |
Displays the frame size, in bytes, for template u |
Confg Tx Cir |
Displays the transmitted CIR configured |
Confg Tx Pir |
Displays the transmitted PIR configured |
Acp Crit Templ. |
Displays the acceptance criteria template |
Test Types |
Displays the configured test type |
Complet Notif |
enabled — the stream completion trap is enabled disabled — the stream completion trap is disabled |
Test Duration |
Displays the duration, in minutes and seconds, of the test for the service streams |
Time Left |
Displays the amount of time left to the test for the service stream |
Frms Injected |
Displays the total number of frames injected |
Frms Received |
Displays the total number of frames received |
Min Delay (us) |
Displays the minimum delay |
Max Delay (us) |
Displays the maximum delay |
Avg. Delay (us) |
Displays the average delay |
Min Delay Var. (us) |
Displays the minimum delay variation |
Max Delay Var. (us) |
Displays the maximum delay variation |
Avg. Delay Var. (us) |
Displays the average delay variation |
M-factor (kbps) |
Displays the M-factor, in kb/s |
Criteria |
thruput (kbps) — the throughput, in kb/s FLR — the frame loss ratio (FLR) Delay (us) — the delay time Delay Var. (us) — the delay variation |
Acceptable |
Displays the allowed values for the criteria |
Configured |
Displays the configured values for the criteria |
M-factor |
Displays the m-factor for the criteria |
Measured |
Displays the measured values for the criteria |
Result |
Pass — the test has passed for the specific criteria Fail — the test has failed for the specific criteria |
service-tests
service-tests
Syntax
service-tests [service-test-name]
Context
[Tree] (show>test-oam>sath service-tests)
Full Context
show test-oam service-activation-testhead service-tests
Description
This command displays the run summary for one or all Y.1564 service activation tests.
Parameters
- service-test-name
-
Specifies the service test name, up to 64 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS
Output
The following output is an example of service test configuration information, and Output fields: service-tests describes the output fields.
Output exampleshow test-oam service-activation-testhead service-tests
===============================================================================
Y.1564 Service Activation Test Run Summary
===============================================================================
Service Test Name Run Completed (UTC)
-------------------------------------------------------------------------------
10 1 2021/05/03 19:13:08
10 2 2021/05/03 19:18:35
10 3 2021/05/03 19:23:40
10 4 2021/05/03 19:23:57
10 5 2021/05/03 19:29:05
10 6 2021/05/03 19:33:11
10 7 2021/05/03 19:39:08
10 8 2021/05/03 19:40:48
10 9 2021/05/03 22:20:24
10 10 2021/05/07 16:42:40
-------------------------------------------------------------------------------
No. of Y.1564 Service Activation Test Runs: 10
===============================================================================
Label |
Description |
---|---|
Service Test Name |
Displays the name of the service test |
Run |
Displays the run number |
Completed (UTC) |
Displays the date and time that the specified service test was completed |
service-using
service-using
Syntax
service-using [epipe] [ies] [vpls] [vprn] [ mirror] [apipe] [fpipe] [ipipe] [cpipe] [ etree] [b-vpls] [i-vpls] [m-vpls] [ sdp sdp-id] [customer customer-id] [creation creation-origin]
Context
[Tree] (show>service service-using)
Full Context
show service service-using
Description
This command displays the services matching certain usage properties. Not all syntax options are available for each router type.
If no optional parameters are specified, all services defined on the system are displayed.
Parameters
- epipe
-
Displays Epipe services.
- ies
-
Displays IES services.
- vpls
-
Displays VPLS services.
- vprn
-
Displays VPRN services.
- mirror
-
Displays mirror services.
- apipe
-
Displays Apipe services.
- fpipe
-
Displays Fpipe services.
- ipipe
-
Displays Ipipe services.
- cpipe
-
Displays Cpipe services.
- etree
-
Displays etree services.
- b-vpls
-
Specifies the B-component instance of the Provider Backbone Bridging (PBB/IEEE 802.1ah) feature. It represents the multi-point tunneling component that multiplexes multiple customer VPNs (ISIDs) together. It is similar to a regular VPLS instance that operates on the backbone MAC addresses.
- i-vpls
-
Specifies the I-component instance of the Provider Backbone Bridging (PBB/IEEE 802.1ah) feature. It identifies the specific VPN entity associated to a customer multipoint (E-LAN) service. It is similar to a regular VPLS instance that operates on the customer MAC addresses.
- m-vpls
-
Specifies the M-component (managed VPLS) instance of the Provider Backbone Bridging (PBB/IEEE 802.1ah) feature.
- sdp-id
-
Displays only services bound to the specified SDP ID.
- customer-id
-
Displays services only associated with the specified customer ID.
- creation-origin
-
Specifies the method by which the service was created.
Platforms
All
Output
The following output is an example of service using information, and Show Service-Using Output Fields describes the output fields.
Output Example*A:ALA-12# show service service-using customer 10
==============================================================================
Services
==============================================================================
ServiceId Type Adm Opr CustomerId Last Mgmt Change
------------------------------------------------------------------------------
1 VPLS Up Up 10 09/05/2006 13:24:15
100 IES Up Up 10 09/05/2006 13:24:15
300 Epipe Up Up 10 09/05/2006 13:24:15
------------------------------------------------------------------------------
Matching Services : 3
==============================================================================
*A:ALA-12#
*A:ALA-12# show service service-using
===============================================================================
Services
===============================================================================
ServiceId Type Adm Opr CustomerId Last Mgmt Change
-------------------------------------------------------------------------------
1 uVPLS Up Up 1 10/26/2006 15:44:57
2 Epipe Up Down 1 10/26/2006 15:44:57
10 mVPLS Down Down 1 10/26/2006 15:44:57
11 mVPLS Down Down 1 10/26/2006 15:44:57
100 mVPLS Up Up 1 10/26/2006 15:44:57
101 mVPLS Up Up 1 10/26/2006 15:44:57
102 mVPLS Up Up 1 10/26/2006 15:44:57
999 uVPLS Down Down 1 10/26/2006 16:14:33
-------------------------------------------------------------------------------
Matching Services : 8
-------------------------------------------------------------------------------
*A:ALA-12#
The following output is an example of epipe service information for the 7450 ESS or 7750 SR.
*A:ALA-12# show service service-using epipe
===============================================================================
Services [epipe]
===============================================================================
ServiceId Type Adm Opr CustomerId Last Mgmt Change
-------------------------------------------------------------------------------
6 Epipe Up Up 6 06/22/2006 23:05:58
7 Epipe Up Up 6 06/22/2006 23:05:58
8 Epipe Up Up 3 06/22/2006 23:05:58
103 Epipe Up Up 6 06/22/2006 23:05:58
-------------------------------------------------------------------------------
Matching Services : 4
===============================================================================
*A:ALA-12#
Label |
Description |
---|---|
Service Id |
The service identifier. |
Type |
Specifies the service type configured for the service ID. |
Adm |
The desired state of the service. |
Opr |
The operating state of the service. |
CustomerID |
The ID of the customer who owns this service. |
Last Mgmt Change |
The date and time of the most recent management-initiated change to this service. |
services
services
Syntax
services vc-type vc-type saii global-id: prefix:ac-id taii [256 chars max] agi agi [ detail] [service-id service-id] [session ip-addr[label-space]]
services vc-type vc-type agi agi [ detail] [service-id service-id] [session ip-addr[label-space]]
services [vc-type vc-type] [svc-fec-type] [ detail] [service-id service-id] [session ip-addr[label-space]]
services vc-type vc-type vc-id vc-id [ detail] [service-id service-id] [session ip-addr[label-space]]
Context
[Tree] (show>router>ldp>bindings services)
Full Context
show router ldp bindings services
Description
This command displays LDP service FEC bindings.
Parameters
- vc-type vc-type
-
Displays information about the VC type associated with this service FEC.
ethernet, vlan, mirror, frdlci, atmsdu, atmcell, atmvcc, atmvpc, ipipe, satop-e1, satop-t1, cesopsn, cesopsn-cas
- vc-id vc-id
-
Displays information about the VC ID associated with this service FEC.
- saii global-id:prefix:ac-id
-
Specifies the a SAII (Source Attachment Individual Identifier).
- taii
-
Specifies the TAII ID, up to 256 characters, associated with this service FEC.
- svc-fec-type
-
Specifies the FEC type.
- agi agi
-
Specifies the Attachment Group identifier TLV associated with this service FEC.
- detail
-
Displays detailed information.
- service-id
-
Specifies the service ID number to display.
- svc-fec-type
-
Specifies the FEC type.
- session ip-addr
-
displays configuration information about LDP sessions.
- label-space
-
Specifies the label space identifier that the router is advertising on the interface.
Platforms
All
session
session
Syntax
session [user-name user-name] [ sub-ppp-type {oe | ol2tp}] [interface ip-int-name | ip-address] [inter-dest-id intermediate-destination-id] [no-inter-dest-id] [ip-address ip-prefix[/prefix-length]] [port port-id] [sap sap-id] [termination-type ppp-session-type] [mlppp] [steering-profile steering-profile] [circuit-id circuit-id] [remote-id remote-id]
session [user-name user-name] [ circuit-id circuit-id] [remote-id remote-id] detail
session [user-name user-name] [ circuit-id circuit-id] [remote-id remote-id] statistics
Context
[Tree] (show>service>id>ppp session)
Full Context
show service id ppp session
Description
This command displays PPP session information.
Parameters
- user-name
-
Displays session information about the PPP user name.
- sub-ppp-type
-
Displays session information about the sub PPP type.
- ip-int-name
-
Displays session information about the specified interface.
- ip-address
-
Displays session information about the IP address.
- intermediate-destination-id
-
Displays session information about the intermediate destination identifier, up to 32 characters, which is encoded in the identification strings.
- no-inter-dest-id
-
Displays session information about no intermediate destination ID.
- ip-prefix/prefix-length
-
Displays session information about the specified IP address and mask.
- port-id
-
Displays session information about the specified port.
- sap-id
-
Displays session information about the specified SAP.
- ppp-session-type
-
Displays session information about the specified PPP session type.
- mlppp
-
Displays session information about MLPPP.
- steering-profile
-
Displays session information about the specified steering profile, up to 32 characters.
- circuit-id
-
Displays session information about the specified circuit ID, up to 256 characters.
- remote-id
-
Displays session information about the specified remote ID, up to 256 characters.
- detail
-
Displays detailed session information.
- statistics
-
Displays PPP session statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of service PPP session information.
Output Exampleshow service id 1000 ppp session detail
===============================================================================
PPP sessions for service 1000
===============================================================================
User-Name : user-1@bng-2.com
Description : svc:1000 sap:[1/x1/1/c1/4:2211.1001]
mac:00:bb:02:00:01:01 sid:1
Up Time : 0d 00:02:03
Type : oE
Termination : local
IP/L2TP-Id/If-Id : 10.2.1.201 02:BB:02:FF:FE:00:01:01
MC-Standby : No
Session Time Left : N/A
LCP State : Opened
IPCP State : Opened
IPv6CP State : Opened
PPP MTU : 1492
PPP Auth-Protocol : CHAP
Keepalive Origin : Radius
Keepalive Interval : 15
Keepalive Multiplier : 2
PPP User-Name : user-1@bng-2.com
Subscriber-interface : sub-int-1
Group-interface : group-int-1-1
IP Origin : local-user-db
DNS Origin : none
NBNS Origin : none
Subscriber : user-1@bng-2.com
Sub-Profile-String : "sub-profile-1"
SLA-Profile-String : "sla-profile-1"
SPI group ID : (Not Specified)
ANCP-String : ""
Int-Dest-Id : ""
App-Profile-String : ""
Category-Map-Name : ""
Acct-Session-Id : "0613FF0000000163FF4F0A"
Sap-Session-Index : 1
IP Address : 10.2.1.201/24
Primary DNS : N/A
Secondary DNS : N/A
Primary NBNS : N/A
Secondary NBNS : N/A
Address-Pool : N/A
IPv6 Prefix : N/A
IPv6 Prefix Origin : none
IPv6 Prefix Pool : ""
IPv6 Del.Pfx. : 2001:db8:b201:a100::/56
IPv6 Del.Pfx. Origin : local-user-db
IPv6 Del.Pfx. Pool : ""
IPv6 Address : 2001:db8:b002:1a1::1
IPv6 Address Origin : local-user-db
IPv6 Address Pool : ""
Primary IPv6 DNS : N/A
Secondary IPv6 DNS : N/A
Router adv. policy : N/A
Ignoring DF bit : false
Radius sub-if prefix : N/A
Circuit-Id :
Remote-Id :
Radius Session-TO : N/A
Radius Class 1 : This is a Class attribute
Radius User-Name : user-1@bng-2.com
Logical-Line-Id :
-------------------------------------------------------------------------------
Managed Routes
-------------------------------------------------------------------------------
IP Address Status Metric Tag Pref
-------------------------------------------------------------------------------
2001:db8:b201:a100::/56 installed 0 none 0
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of sessions: 1
===============================================================================
Service PPP Session Field Descriptions describes PPP session field information.
Field |
Description |
---|---|
User-Name |
The user name |
Description |
The description |
Up Time |
The time of the last modification |
Type |
The PPP type |
Termination |
The termination type |
IP/L2TP-Id/If-Id |
The IP/L2TP or IF ID |
MC-Standby |
The MC standby |
Session Time Left |
The time remaining for the session timeout |
LCP State |
The LCP open/closed state |
IPCP State |
The IP CP open/closed state |
IPv6CP State |
The IPv6 CP open/closed state |
PPP MTU |
The PPP MTU value |
PPP Auth-Protocol |
The PPP authentication protocol |
PPP User-Name |
The PPP user name |
Subscriber-interface |
The subscriber interface name |
Group-interface |
The group interface name |
IP Origin |
The IP origin |
DNS Origin |
The DNS origin |
NBNS Origin |
The NBNS origin |
Subscriber |
The subscriber identification string |
Sub-Profile-String |
The subscriber profile name |
SLA-Profile-String |
The SLA profile name |
SPI group ID |
The SPI group ID |
ANCP-String |
The value of the ancp-string received from either the DHCP or the RADIUS server |
Int-Dest-Id |
Intermediate destination identifier received from the RADIUS server |
App-Profile-String |
The application profile string |
Category-Map-Name |
The value of the category map name received from the RADIUS server |
Acct-Session-Id |
The accounting session ID |
Sap-Session-Index |
The sap session index of the PPP session |
IP Address |
The IP address |
Primary DNS |
The primary DNS server |
Secondary DNS |
The secondary DNS server |
Primary NBNS |
The primary NBNS server |
Secondary NBNS |
The secondary NBNS server |
Address-Pool |
The IP address pool used to search for an IP address for this session |
IPv6 Prefix |
The IPv6 prefix |
IPv6 Prefix Origin |
The origin of the IPv6 prefix |
IPv6 Prefix Pool |
The DHCP server pool from which the IPv6 prefix is allocated |
IPv6 Del.Pfx. |
The IPv6 delegated prefix |
IPv6 Del.Pfx. Origin |
The origin of the IPv6 delegated prefix |
IPv6 Del.Pfx. Pool |
The DHCP server pool from which the delegated prefix is allocated |
IPv6 Address |
The IPv6 address |
IPv6 Address Origin |
The origin of the IPv6 address |
IPv6 Address Pool |
The DHCP server pool from which the address is allocated |
Primary IPv6 DNS |
The primary IPv6 DNS server |
Secondary IPv6 DNS |
The secondary IPv6 DNS server |
Router adv. policy |
The router advertisement policy |
Ignoring DF bit |
The true/false status of ignoring DF bit |
Radius sub-if prefix |
The RADIUS subscriber interface prefix |
Circuit-Id |
The circuit ID of the PPP session |
Remote-Id |
The remote ID of the PPP session |
Radius Session-TO |
The value to interpret the session timeout VSA from RADIUS |
Radius Class 1 |
The Class attribute returned by the RADIUS server in an Access-Accept message |
Radius User-Name |
The User-Name attribute returned by the RADIUS server in an Access-Accept message |
Logical-Line-Id |
The logical line ID |
Subscriber Host Limit Overrides and SLA Profile Instance Host Limit Overrides: (only shown when overrides are active) |
|
ipv4-arp |
The total number of IPv4 ARP hosts limit |
ipv4-dhcp |
The total number of IPv4 DHCP hosts limit |
ipv4-ppp |
The total number of IPv4 PPP hosts limit |
ipv4-overall |
The total number of IPv4 hosts limit |
ipv6-pd-ipoe-dhcp |
The total number of IPv6 IPoE DHCP Prefix Delegation hosts (IA-PD) limit |
ipv6-pd-ppp-dhcp |
The total number of IPv6 PPPoE DHCP Prefix Delegation hosts (IA-PD) limit |
ipv6-pd-overall |
The total number of IPv6 DHCP Prefix Delegation hosts (IA-PD) limit |
ipv6-wan-ipoe-dhcp |
The total number of IPv6 IPoE DHCP WAN hosts (IA-NA) limit |
ipv6-wan-ipoe-slaac |
The total number of IPv6 IPoE SLAAC WAN hosts limit |
ipv6-wan-ppp-dhcp |
The total number of IPv6 PPPoE DHCP WAN hosts (IA-NA) limit |
ipv6-wan-ppp-slaac |
The total number of IPv6 IPoE SLAAC WAN hosts limit |
ipv6-wan-overall |
The total number of IPv6 WAN hosts limit |
ipv6-overall |
The total number of IPv6 hosts limit |
lac-overall |
The total number of L2TP LAC hosts limit |
overall |
The total number of subscriber hosts limit |
Subscriber Session Limit Overrides and SLA Profile Instance Session Limit Overrides: (only shown when overrides are active) |
|
ipoe |
The total number of IPoE sessions limit |
ppoe-local |
The total number of PPPoE local terminated sessions (PTA) limit |
ppoe-lac |
The total number of PPPoE L2TP LAC sessions limit |
ppoe-overall |
The total number of PPPoE sessions limit |
l2tp-lns |
The total number of L2TP LNS sessions limit |
l2tp-lts |
The total number of L2TP LTS sessions limit |
l2tp-overall |
The total number of L2TP sessions limit |
overall |
The total number of subscriber sessions limit |
Managed Routes |
|
Status |
The installation status |
Metric |
The metric value |
Tag |
The tag value |
Pref |
The preference value |
Number of session |
The number of sessions returned from the search criteria |
session
Syntax
session connection-id connection-id [{detail | ppp-statistics}]
session [{detail | ppp-statistics}] [session-id session-id] [state session-state] [peer ip-address] [group group-name] [assignment-id assignment-id] [local-name local-host-name] [ remote-name remote-host-name] [tunnel-id tunnel-id] [ service service-id [interface {ip-int-name | ip-address}]] [ip-prefix ip-prefix/mask]
session [{detail | ppp-statistics}] [state session-state] [peer ip-address] [group group-name] [assignment-id assignment-id] [local-name local-host-name] [remote-name remote-host-name] [ control-connection-id connection-id] [service service-id [interface {ip-int-name | ip-address}]]
Context
[Tree] (show>router>l2tp session)
Full Context
show router l2tp session
Description
This command displays L2TP session operational information.
Parameters
- connection-id
-
Specifies the identification number for a Layer Two Tunneling Protocol connection.
- detail
-
Displays detailed L2TP session information.
- ppp-statistics
-
Displays PPP statistics for the session.
- session-id
-
Specifies the identification number for a Layer Two Tunneling Protocol session.
- session-state
-
Specifies the values to identify the operational state of the L2TP session.
- ip-address
-
Specifies the IP address of the peer.
- group-name
-
Specifies a string to identify a Layer Two Tunneling Protocol Tunnel group.
- assignment-id
-
Specifies a string that distinguishes this Layer Two Tunneling Protocol tunnel.
- local-host-name
-
Specifies the host name used by this system during the authentication phase of tunnel establishment.
- remote-host-name
-
Specifies a string that is compared to the host name used by the tunnel peer during the authentication phase of tunnel establishment.
- tunnel-id
-
Specifies the local identifier of this Layer Two Tunneling Protocol tunnel, when L2TP version 2 is used.
- service-id
-
Specifies the service identification number.
- ip-int-name
-
Specifies the IP interface name.
- ip-address
-
Specifies the IPv4 or IPv6 addresses.
- ip-prefix/mask
-
Specifies information for the specified IP prefix and mask length.
- connection-id
-
Specifies an identification number for a Layer Two Tunneling Protocol session.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of L2TP session operational information.
Output Example*A:Dut-C# show router l2tp session
===============================================================================
L2TP Session Summary
===============================================================================
ID Control Conn ID Tunnel-ID Session-ID State
-------------------------------------------------------------------------------
143524786 143523840 2190 946 established
143526923 143523840 2190 3083 established
143531662 143523840 2190 7822 closed
236926987 236912640 3615 14347 closed
236927915 236912640 3615 15275 closed
379407426 379387904 5789 19522 established
658187773 658178048 10043 9725 established
658198275 658178048 10043 20227 established
658210606 658178048 10043 32558 established
-------------------------------------------------------------------------------
No. of sessions: 9
===============================================================================
*A:Dut-C#
*A:Dut-C# show router l2tp session state established
===============================================================================
L2TP Session Summary
===============================================================================
ID Control Conn ID Tunnel-ID Session-ID State
-------------------------------------------------------------------------------
143524786 143523840 2190 946 established
143526923 143523840 2190 3083 established
379407426 379387904 5789 19522 established
658187773 658178048 10043 9725 established
658198275 658178048 10043 20227 established
658210606 658178048 10043 32558 established
-------------------------------------------------------------------------------
No. of sessions: 6
===============================================================================
*A:Dut-C#
*A:Dut-C# show router l2tp session state closed detail
===============================================================================
L2TP Session Status
===============================================================================
Connection ID : 143531662
State : closed
Tunnel Group : isp1.group-2
Assignment ID : isp1.tunnel-3
Error Message : Terminated by PPPoE: RX PADT
Control Conn ID : 143523840 Remote Conn ID : 1148557524
Tunnel ID : 2190 Remote Tunnel ID : 17525
Session ID : 7822 Remote Session ID : 39124
Time Started : 04/17/2009 18:44:37
Time Established : 04/17/2009 18:44:37 Time Closed : 04/17/2009 18:44:50
CDN Result : generalError General Error : noError
-------------------------------------------------------------------------------
===============================================================================
L2TP Session Status
===============================================================================
Connection ID : 236926987
State : closed
Tunnel Group : isp1.group-2
Assignment ID : isp1.tunnel-2
Error Message : tunnel was closed
Control Conn ID : 236912640 Remote Conn ID : 3861360381
Tunnel ID : 3615 Remote Tunnel ID : 58919
Session ID : 14347 Remote Session ID : 44797
Time Started : 04/17/2009 18:41:55
Time Established : 04/17/2009 18:41:55 Time Closed : 04/17/2009 18:43:20
CDN Result : generalError General Error : noError
-------------------------------------------------------------------------------
===============================================================================
L2TP Session Status
===============================================================================
Connection ID : 236927915
State : closed
Tunnel Group : isp1.group-2
Assignment ID : isp1.tunnel-2
Error Message : tunnel was closed
Control Conn ID : 236912640 Remote Conn ID : 3861317210
Tunnel ID : 3615 Remote Tunnel ID : 58919
Session ID : 15275 Remote Session ID : 1626
Time Started : 04/17/2009 18:41:03
Time Established : 04/17/2009 18:41:03 Time Closed : 04/17/2009 18:43:20
CDN Result : generalError General Error : noError
-------------------------------------------------------------------------------
No. of sessions: 3
===============================================================================
*A:Dut-C#
*A:Dut-C# show router l2tp session session-id 946
===============================================================================
L2TP Session Summary
===============================================================================
ID Control Conn ID Tunnel-ID Session-ID State
-------------------------------------------------------------------------------
143524786 143523840 2190 946 established
-------------------------------------------------------------------------------
No. of sessions: 1
===============================================================================
*A:Dut-C# show router l2tp session connection-id 143524786 detail
===============================================================================
L2TP Session Status
===============================================================================
Connection ID : 143524786
State : established
Tunnel Group : isp1.group-2
Assignment ID : isp1.tunnel-3
Error Message : N/A
Control Conn ID : 143523840 Remote Conn ID : 1148528691
Tunnel ID : 2190 Remote Tunnel ID : 17525
Session ID : 946 Remote Session ID : 10291
Time Started : 04/17/2009 18:42:01
Time Established : 04/17/2009 18:42:01 Time Closed : N/A
CDN Result : noError General Error : noError
-------------------------------------------------------------------------------
*A:Dut-C#
*A:Dut-C# show router l2tp session group isp1.group-2
===============================================================================
L2TP Session Summary
===============================================================================
ID Control Conn ID Tunnel-ID Session-ID State
-------------------------------------------------------------------------------
143524786 143523840 2190 946 established
143526923 143523840 2190 3083 established
143531662 143523840 2190 7822 closed
236926987 236912640 3615 14347 closed
236927915 236912640 3615 15275 closed
658187773 658178048 10043 9725 established
658198275 658178048 10043 20227 established
658210606 658178048 10043 32558 established
-------------------------------------------------------------------------------
No. of sessions: 8
===============================================================================
*A:Dut-C#
*A:Dut-C# show router l2tp session tunnel-id 2190 state closed detail
===============================================================================
L2TP Session Status
===============================================================================
Connection ID : 143531662
State : closed
Tunnel Group : isp1.group-2
Assignment ID : isp1.tunnel-3
Error Message : Terminated by PPPoE: RX PADT
Control Conn ID : 143523840 Remote Conn ID : 1148557524
Tunnel ID : 2190 Remote Tunnel ID : 17525
Session ID : 7822 Remote Session ID : 39124
Time Started : 04/17/2009 18:44:37
Time Established : 04/17/2009 18:44:37 Time Closed : 04/17/2009 18:44:50
CDN Result : generalError General Error : noError
-------------------------------------------------------------------------------
No. of sessions: 1
===============================================================================
*A:Dut-C#
*A:Dut-C# show router l2tp session assignment-id isp1.tunnel-2
===============================================================================
L2TP Session Summary
===============================================================================
ID Control Conn ID Tunnel-ID Session-ID State
-------------------------------------------------------------------------------
236926987 236912640 3615 14347 closed
236927915 236912640 3615 15275 closed
658187773 658178048 10043 9725 established
658198275 658178048 10043 20227 established
658210606 658178048 10043 32558 established
-------------------------------------------------------------------------------
No. of sessions: 5
===============================================================================
*A:Dut-C#
*A:Dut-C# show router l2tp session assignment-id isp1.tunnel-2 state established
===============================================================================
L2TP Session Summary
===============================================================================
ID Control Conn ID Tunnel-ID Session-ID State
-------------------------------------------------------------------------------
658187773 658178048 10043 9725 established
658198275 658178048 10043 20227 established
658210606 658178048 10043 32558 established
-------------------------------------------------------------------------------
No. of sessions: 3
===============================================================================
*A:Dut-C#
*A:Dut-C# show router l2tp session control-connection-id 658178048
===============================================================================
L2TP Session Summary
===============================================================================
ID Control Conn ID Tunnel-ID Session-ID State
-------------------------------------------------------------------------------
658187773 658178048 10043 9725 established
658198275 658178048 10043 20227 established
658210606 658178048 10043 32558 established
-------------------------------------------------------------------------------
No. of sessions: 3
===============================================================================
*A:Dut-C#
*A:Dut-C# show router l2tp session peer 10.10.20.100
===============================================================================
L2TP Session Summary
===============================================================================
ID Control Conn ID Tunnel-ID Session-ID State
-------------------------------------------------------------------------------
236926987 236912640 3615 14347 closed
236927915 236912640 3615 15275 closed
658187773 658178048 10043 9725 established
658198275 658178048 10043 20227 established
658210606 658178048 10043 32558 established
-------------------------------------------------------------------------------
No. of sessions: 5
===============================================================================
*A:Dut-C#
*A:Dut-C# show router l2tp session peer 10.10.20.100 state closed detail
===============================================================================
L2TP Session Status
===============================================================================
Connection ID : 236926987
State : closed
Tunnel Group : isp1.group-2
Assignment ID : isp1.tunnel-2
Error Message : tunnel was closed
Control Conn ID : 236912640 Remote Conn ID : 3861360381
Tunnel ID : 3615 Remote Tunnel ID : 58919
Session ID : 14347 Remote Session ID : 44797
Time Started : 04/17/2009 18:41:55
Time Established : 04/17/2009 18:41:55 Time Closed : 04/17/2009 18:43:20
CDN Result : generalError General Error : noError
-------------------------------------------------------------------------------
===============================================================================
L2TP Session Status
===============================================================================
Connection ID : 236927915
State : closed
Tunnel Group : isp1.group-2
Assignment ID : isp1.tunnel-2
Error Message : tunnel was closed
Control Conn ID : 236912640 Remote Conn ID : 3861317210
Tunnel ID : 3615 Remote Tunnel ID : 58919
Session ID : 15275 Remote Session ID : 1626
Time Started : 04/17/2009 18:41:03
Time Established : 04/17/2009 18:41:03 Time Closed : 04/17/2009 18:43:20
CDN Result : generalError General Error : noError
-------------------------------------------------------------------------------
No. of sessions: 2
===============================================================================
*A:Dut-C#
*A:Dut-C# show router l2tp session local-name lac1.wholesaler.com
===============================================================================
L2TP Session Summary
===============================================================================
ID Control Conn ID Tunnel-ID Session-ID State
-------------------------------------------------------------------------------
143524786 143523840 2190 946 established
143526923 143523840 2190 3083 established
143531662 143523840 2190 7822 closed
236926987 236912640 3615 14347 closed
236927915 236912640 3615 15275 closed
379407426 379387904 5789 19522 established
658187773 658178048 10043 9725 established
658198275 658178048 10043 20227 established
658210606 658178048 10043 32558 established
-------------------------------------------------------------------------------
No. of sessions: 9
===============================================================================
*A:Dut-C#
*A:Dut-C# show router l2tp session local-name lac1.wholesaler.com remote-
name lns.retailer1.net
===============================================================================
L2TP Session Summary
===============================================================================
ID Control Conn ID Tunnel-ID Session-ID State
-------------------------------------------------------------------------------
379407426 379387904 5789 19522 established
-------------------------------------------------------------------------------
No. of sessions: 1
===============================================================================
*A:Dut-C#
*A:Fden-Dut2-BSA2# show router l2tp session connection-id 600407016
===============================================================================
L2TP Session Summary
===============================================================================
ID Control Conn ID Tunnel-ID Session-ID State
-------------------------------------------------------------------------------
600407016 600375296 9161 31720 established
simon@base.lac.base.lns
interface: gi_base_lns_base_lac
service-id: 100
ip-address: 10.100.2.1
===============================================================================
*A:Fden-Dut2-BSA2# show router l2tp session connection-id 600407016 detail
===============================================================================
L2TP Session Status
===============================================================================
Connection ID: 600407016
State : established
Tunnel Group : base_lns_base_lac
Assignment ID: t1
Error Message: N/A
Control Conn ID : 600375296 Remote Conn ID : 1026712216
Tunnel ID : 9161 Remote Tunnel ID : 15666
Session ID : 31720 Remote Session ID : 25240
Time Started : 02/02/2010 09:08:54
Time Established : 02/02/2010 09:08:54 Time Closed : N/A
CDN Result : noError General Error : noError
-------------------------------------------------------------------------------
PPP information
Service Id : 100
Interface : gi_base_lns_base_lac
LCP State : opened
IPCP State : opened
IPv6CP State : initial
PPP MTU : 1492
PPP Auth-Protocol : chap
PPP User-Name : simon@base.lac.base.lns
Subscriber Origin : radius
Strings Origin : radius
IPCP Info Origin : radius
IPv6CP Info Origin : none
Subscriber : "simon"
Sub-Profile-String : "sub1"
SLA-Profile-String : "sla1"
ANCP-String : ""
Int-Dest-Id : ""
App-Profile-String : ""
Category-Map-Name : ""
IP Address : 10.100.2.1
Primary DNS : N/A
Secondary DNS : N/A
Primary NBNS : N/A
Secondary NBNS : N/A
Address-Pool : N/A
IPv6 Prefix : N/A
IPv6 Del.Pfx. : N/A
Primary IPv6 DNS : N/A
Secondary IPv6 DNS : N/A
Circuit-Id : (Not Specified)
Remote-Id : (Not Specified)
Session-Timeout : N/A
Radius Class : (Not Specified)
Radius User-Name : simon@base.lac.base.lns
session
Syntax
session [interface ip-int-name | ip-address | sap sap-id] [session-id session-id] [ mac ieee-address] [ip-address ip-address[/ mask]] [port port-id] [no-inter-dest-id | inter-dest-id intermediate-destination-id] [steering-profile steering-profile] [router-advertisement-policy policy-name] [ detail | statistics]
session l2tp-connection-id connection-id [detail | statistics]
Context
[Tree] (show>service>id>pppoe session)
Full Context
show service id pppoe session
Description
This command displays PPPoE session information.
Parameters
- ip-int-name
-
Specifies the IP interface name.
- ip-address
-
Specifies the IP address of the PPPoE session.
- sap-id
-
Specifies the SAP ID.
- session-id
-
Specifies the ID of the PPPoE session.
- ieee-address
-
Specifies the MAC address of the PPPoE session.
- port-id
-
Specifies the port ID.
- no-inter-dest-id
-
Displays the information of PPPoE sessions that do not have an intermediate destination ID associated.
- intermediate-destination-id
-
Specifies the intermediate destination ID.
- steering-profile
-
Specifies the name of the steering profile, up to a maximum of 32 characters.
- policy-name
-
Specifies the name of the router advertisement policy, up to a maximum of 32 characters.
- detail
-
Displays detailed information.
- statistics
-
Displays statistics about the PPPoE session.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following outputs are examples of PPPoE session information and Service PPPoE Session Field Descriptions describes the output fields.
show service id 20 pppoe session
===============================================================================
PPPoE sessions for svc-id 20
===============================================================================
Sap Id Mac Address Sid Up Time IP Address
-------------------------------------------------------------------------------
1/1/3:200 00:00:00:00:00:03 1 1d 00:48:39 10.0.0.101
1/1/3:300 00:00:00:00:00:05 1 0d 00:01:08 10.0.0.119
-------------------------------------------------------------------------------
Number of sessions : 2
===============================================================================
show service id 1000 pppoe session detail
===============================================================================
PPPoE sessions for svc-id 1000
===============================================================================
Sap Id Mac Address Sid Up Time Type
IP/L2TP-Id/Interface-Id MC-Stdby
-------------------------------------------------------------------------------
[1/x1/1/c1/4:2211.* 00:bb:02:00:01:01 1 0d 00:01:55 local
10.2.1.201
02:BB:02:FF:FE:00:01:01
LCP State : Opened
IPCP State : Opened
IPv6CP State : Opened
PPP MTU : 1492
PPP Auth-Protocol : CHAP
PPP User-Name : user-1@bng-2.com
Subscriber-interface : sub-int-1
Group-interface : group-int-1-1
IP Origin : local-user-db
DNS Origin : none
NBNS Origin : none
Subscriber : user-1@bng-2.com
Sub-Profile-String : "sub-profile-1"
SLA-Profile-String : "sla-profile-1"
SPI group ID : (Not Specified)
ANCP-String : ""
Int-Dest-Id : ""
App-Profile-String : ""
Category-Map-Name : ""
Acct-Session-Id : "0613FF0000000163FF4F0A"
Sap-Session-Index : 1
IP Address : 10.2.1.201/24
Primary DNS : N/A
Secondary DNS : N/A
Primary NBNS : N/A
Secondary NBNS : N/A
Address-Pool : N/A
IPv6 Prefix : N/A
IPv6 Prefix Origin : none
IPv6 Prefix Pool : ""
IPv6 Del.Pfx. : 2001:db8:b201:a100::/56
IPv6 Del.Pfx. Origin : local-user-db
IPv6 Del.Pfx. Pool : ""
IPv6 Address : 2001:db8:b002:1a1::1
IPv6 Address Origin : local-user-db
IPv6 Address Pool : ""
Primary IPv6 DNS : N/A
Secondary IPv6 DNS : N/A
Router adv. policy : N/A
Ignoring DF bit : false
Radius sub-if prefix : N/A
Circuit-Id :
Remote-Id :
Radius Session-TO : N/A
Radius Class 1 : This is a Class attribute
Radius User-Name : user-1@bng-2.com
Logical-Line-Id :
Service-Name : HSI
-------------------------------------------------------------------------------
Managed Routes
-------------------------------------------------------------------------------
IP Address Status Metric Tag Pref
-------------------------------------------------------------------------------
2001:db8:b201:a100::/56 installed 0 none 0
-------------------------------------------------------------------------------
Keepalive Origin : Radius
Keepalive Interval : 15
Keepalive Multiplier : 2
-------------------------------------------------------------------------------
Number of sessions : 1
===============================================================================
* indicates that the corresponding row element may have been truncated.
show service id 20 pppoe session ip-address 20.0.0.101 detail
===============================================================================
PPPoE sessions for svc-id 20
===============================================================================
Sap Id Mac Address Sid Up Time IP Address
-------------------------------------------------------------------------------
1/1/3:200 00:00:00:00:00:03 1 1d 00:49:46 10.0.0.101
LCP State : Opened
IPCP State : Opened
PPP MTU : 1492
PPP Auth-Protocol : PAP
PPP User-Name : user4@domain1
Subscriber-interface : sub_pppoe
Group-interface : grp_pppoe2
Subscriber Origin : RADIUS
Strings Origin : RADIUS
IPCP Info Origin : DHCP
Subscriber : "radius_papchap4"
Sub-Profile-String : "sub1"
SLA-Profile-String : "sla1"
ANCP-String : ""
Int-Dest-Id : ""
App-Profile-String : ""
Primary DNS : N/A
Secondary DNS : N/A
Primary NBNS : N/A
Secondary NBNS : N/A
Circuit-Id : 2
Remote-Id :
Session-Timeout : N/A
-------------------------------------------------------------------------------
Number of sessions : 1
===============================================================================
show service id 20 pppoe session ip-address 20.0.0.101 statistics
===============================================================================
PPPoE sessions for svc-id 20
===============================================================================
Sap Id Mac Address Sid Up Time IP Address
-------------------------------------------------------------------------------
1/1/3:200 00:00:00:00:00:03 1 1d 00:50:39 10.0.0.101
Packet Type Received Transmitted
-------------------------------------------------------------------------------
LCP Configure-Request 1 2
LCP Configure-Ack 1 1
LCP Configure-Nak 1 0
LCP Configure-Reject 0 0
LCP Terminate-Request 0 0
LCP Terminate-Ack 0 0
LCP Code-Reject 0 0
LCP Echo-Request 8927 866
LCP Echo-Reply 866 8927
LCP Protocol-Reject 0 0
LCP Discard-Request 0 0
-------------------------------------------------------------------------------
PAP Authenticate-Request 1 -
PAP Authenticate-Ack - 1
PAP Authenticate-Nak - 0
-------------------------------------------------------------------------------
CHAP Challenge - 0
CHAP Response 0 -
CHAP Success - 0
CHAP Failure - 0
-------------------------------------------------------------------------------
IPCP Configure-Request 2 1
IPCP Configure-Ack 1 1
IPCP Configure-Nak 0 1
IPCP Configure-Reject 0 0
IPCP Terminate-Request 0 0
IPCP Terminate-Ack 0 0
IPCP Code-Reject 0 0
-------------------------------------------------------------------------------
Unknown Protocol 0 -
-------------------------------------------------------------------------------
Number of sessions : 1
===============================================================================
*A:Dut-A#show service id 10 pppoe session router-advertisement-policy "ra-policy-01"
===============================================================================
PPPoE sessions for svc-id 1000
===============================================================================
Sap Id Mac Address Sid Up Time Type
IP/L2TP-Id/Interface-Id MC-Stdby
-------------------------------------------------------------------------------
1/1/20:841 00:00:64:19:01:02 1 0d 00:00:18 local
192.168.0.10
02:00:64:FF:FE:19:01:02
-------------------------------------------------------------------------------
Number of sessions : 1
===============================================================================
Field |
Description |
---|---|
Sap Id |
The SAP ID |
Mac Address |
The MAC address |
Sid |
The SID number |
Up Time |
The time of the last modification |
Type |
The PPPoE type |
IP/L2TP-Id/If-Id |
The IP/L2TP or IF ID |
MC-Standby |
The MC standby |
Session Time Left |
The time remaining for the session timeout |
LCP State |
The LCP open/closed state |
IPCP State |
The IP CP open/closed state |
IPv6CP State |
The IPv6 CP open/closed state |
PPP MTU |
The PPP MTU value |
PPP Auth-Protocol |
The PPP authentication protocol |
PPP User-Name |
The PPP user name |
Subscriber-interface |
The subscriber interface name |
Group-interface |
The group interface name |
IP Origin |
The IP origin |
DNS Origin |
The DNS origin |
NBNS Origin |
The NBNS origin |
Subscriber |
The subscriber identification string |
Sub-Profile-String |
The subscriber profile name |
SLA-Profile-String |
The SLA profile name |
SPI group ID |
The SPI group ID |
ANCP-String |
The value of the ancp-string received from either the DHCP or the RADIUS server |
Int-Dest-Id |
Intermediate destination identifier received from the RADIUS server |
App-Profile-String |
The application profile string |
Category-Map-Name |
The value of the category map name received from the RADIUS server |
Acct-Session-Id |
The accounting session ID |
Sap-Session-Index |
The sap session index of the PPP session |
IP Address |
The IP address |
Primary DNS |
The primary DNS server |
Secondary DNS |
The secondary DNS server |
Primary NBNS |
The primary NBNS server |
Secondary NBNS |
The secondary NBNS server |
Address-Pool |
The IP address pool used to search for an IP address for this session |
IPv6 Prefix |
The IPv6 prefix |
IPv6 Prefix Origin |
The origin of the IPv6 prefix |
IPv6 Prefix Pool |
The DHCP server pool from which the IPv6 prefix is allocated |
IPv6 Del.Pfx. |
The IPv6 delegated prefix |
IPv6 Del.Pfx. Origin |
The origin of the IPv6 delegated prefix |
IPv6 Del.Pfx. Pool |
The DHCP server pool from which the delegated prefix is allocated |
IPv6 Address |
The IPv6 address |
IPv6 Address Origin |
The origin of the IPv6 address |
IPv6 Address Pool |
The DHCP server pool from which the address is allocated |
Primary IPv6 DNS |
The primary IPv6 DNS server |
Secondary IPv6 DNS |
The secondary IPv6 DNS server |
Router adv. policy |
The router advertisement policy |
Ignoring DF bit |
The true/false status of ignoring DF bit |
Radius sub-if prefix |
The RADIUS subscriber interface prefix |
Circuit-Id |
The circuit ID of the PPP session |
Remote-Id |
The remote ID of the PPP session |
Radius Session-TO |
The value to interpret the session timeout VSA from RADIUS |
Radius Class 1 |
The Class attribute returned by the RADIUS server in an Access-Accept message |
Radius User-Name |
The User-Name attribute returned by the RADIUS server in an Access-Accept message |
Logical-Line-Id |
The logical line ID |
Keepalive Origin |
LCP Keepalive Interval and Multiplier parameters are by default obtiained from the ppp-policy configuration and can be overridden with parameters obtained from RADIUS, Diameter Gx or local user database. This field indicates the origin of the LCP Keepalive parameters for this session: Policy = values configured in the subscriber-mgmt ppp-policy for PPPoE PTA sessions or l2tp group context for L2TP LNS sessions. Ludb = values from the local user database Radius = values from RADIUS authentication Diameter Gx = values from Diameter Gx |
Keepalive Interval |
The time interval in seconds at which LCP echo requests are transmitted for the PPP session |
Keepalive Multiplier |
The number of LCP keepalive messages that can be missed before the PPP session is brought down |
Subscriber Host Limit Overrides and SLA Profile Instance Host Limit Overrides: (only shown when overrides are active) |
|
ipv4-arp |
The total number of IPv4 ARP hosts limit |
ipv4-dhcp |
The total number of IPv4 DHCP hosts limit |
ipv4-ppp |
The total number of IPv4 PPP hosts limit |
ipv4-overall |
The total number of IPv4 hosts limit |
ipv6-pd-ipoe-dhcp |
The total number of IPv6 IPoE DHCP Prefix Delegation hosts (IA-PD) limit |
ipv6-pd-ppp-dhcp |
The total number of IPv6 PPPoE DHCP Prefix Delegation hosts (IA-PD) limit |
ipv6-pd-overall |
The total number of IPv6 DHCP Prefix Delegation hosts (IA-PD) limit |
ipv6-wan-ipoe-dhcp |
The total number of IPv6 IPoE DHCP WAN hosts (IA-NA) limit |
ipv6-wan-ipoe-slaac |
The total number of IPv6 IPoE SLAAC WAN hosts limit |
ipv6-wan-ppp-dhcp |
The total number of IPv6 PPPoE DHCP WAN hosts (IA-NA) limit |
ipv6-wan-ppp-slaac |
The total number of IPv6 IPoE SLAAC WAN hosts limit |
ipv6-wan-overall |
The total number of IPv6 WAN hosts limit |
ipv6-overall |
The total number of IPv6 hosts limit |
lac-overall |
The total number of L2TP LAC hosts limit |
overall |
The total number of subscriber hosts limit |
Subscriber Session Limit Overrides and SLA Profile Instance Session Limit Overrides: (only shown when overrides are active) |
|
ipoe |
The total number of IPoE sessions limit |
ppoe-local |
The total number of PPPoE local terminated sessions (PTA) limit |
ppoe-lac |
The total number of PPPoE L2TP LAC sessions limit |
ppoe-overall |
The total number of PPPoE sessions limit |
l2tp-lns |
The total number of L2TP LNS sessions limit |
l2tp-lts |
The total number of L2TP LTS sessions limit |
l2tp-overall |
The total number of L2TP sessions limit |
overall |
The total number of subscriber sessions limit |
Managed Routes |
|
Status |
The installation status |
Metric |
The metric value |
Tag |
The tag value |
Pref |
The preference value |
Number of session |
The number of sessions returned from the search criteria |
session
Syntax
session connection-id connection-id eth-tunnel-statistics
Context
[Tree] (clear>router>l2tp session)
Full Context
clear router l2tp session
Description
This command clears L2TP session data.
Parameters
- connection-id
-
Specifies the L2TPv3 connection ID.
- eth-tunnel-statistics
-
Clears the Ethernet tunnel statistics associated with the specified session.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
session
Syntax
session stop connection-id
Context
[Tree] (tools>perform>router>l2tp session)
Full Context
tools perform router l2tp session
Description
This command configures performance tools for a specified L2TP session.
Parameters
- stop
-
Stops the performance tools for a specified L2TP session.
- connection-id
-
Specifies the L2TPv3 connection ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
session
Syntax
session [sap sap-id] [mac ieee-address] [circuit-id circuit-id] [remote-id remote-id] [interface ip-int-name | ip-address] [ inter-dest-id intermediate-destination-id] [no-inter-dest-id] [ ip-address ip-prefix[/prefix-length]] [port port-id] [subscriber sub-ident-string] [sap-session-id sap-session-index] [detail] [wholesaler service-id] [ router-advertisement-policy policy-name]
Context
[Tree] (show>service>id>ipoe session)
Full Context
show service id ipoe session
Description
This command displays the identified IPoE session details active on the specified service instance.
Parameters
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- ieee-address
-
Specifies the 48-bit MAC address for the static ARP in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee, and ff are hexadecimal numbers. Allowed values are any non-broadcast, non-multicast MAC and non-IEEE reserved MAC addresses.
- circuit-id
-
Specifies the circuit ID, up to 127 characters.
- remote-id
-
Specifies that information that goes into the remote-id sub-option in the DHCP relay packet, up to 255 characters.
- ip-int-name
-
Specifies the name of the IP interface, up to 32 characters.
- ip-address[/prefix-length]
-
Specifies information for the specified IP address and mask.
- no-inter-dest-id
-
Displays the information about no intermediate destination ID.
- port-id
-
Displays information about the specified port ID.
- sap-session-index
-
Displays sap-session-index information.
- service-id
-
Specifies the service ID of the wholesaler.
- intermediate-destination-id
-
Specifies the intermediate destination identifier which is encoded in the identification strings up to 32 characters.
- sub-ident-string
-
Specifies an existing subscriber identification profile.
- detail
-
Displays all IPoE session details.
- policy-name
-
Specifies the name of the router advertisement policy, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of service IPoE session information.
Output Example# show service id 4000 ipoe session
===============================================================================
IPoE sessions for svc-id 4000
===============================================================================
Sap Id Mac Address Up Time MC-Stdby
Subscriber-Id
[CircuitID] | [RemoteID]
-------------------------------------------------------------------------------
1/1/4:1201.27 00:51:00:00:00:0c 0d 00:00:18
ipoe-session-001
-------------------------------------------------------------------------------
CID | RID displayed when included in session-key
Number of sessions : 1
===============================================================================
# show service id 4000 ipoe session detail
===============================================================================
IPoE sessions for service 4000
===============================================================================
SAP : 1/1/4:1201.27
Mac Address : 00:51:00:00:00:0c
Circuit-Id : circuit-id-1
Remote-Id : remote-id-1
Session Key : sap-mac
MC-Standby : No
Subscriber-interface : sub-int-1
Group-interface : group-int-1
Up Time : 0d 00:01:01
Session Time Left : N/A
Last Auth Time : 02/28/2015 01:01:09
Min Auth Intvl (left) : 0d 00:05:00 (0d 00:03:59)
Persistence Key : N/A
Subscriber : "ipoe-session-001"
Sub-Profile-String : "sub-profile-1"
SLA-Profile-String : "sla-profile-1"
ANCP-String : ""
Int-Dest-Id : ""
App-Profile-String : ""
Category-Map-Name : ""
Acct-Session-Id : "144DFF0000001354D806D5"
Sap-Session-Index : 1
IP Address : 10.10.1.201/24
IP Origin : Radius
Primary DNS : N/A
Secondary DNS : N/A
Primary NBNS : N/A
Secondary NBNS : N/A
Address-Pool : N/A
IPv6 Prefix : 2001:db8:a:111::/64
IPv6 Prefix Origin : Radius
IPv6 Prefix Pool : ""
IPv6 Del.Pfx. : 2001:db8:a001:a100::/56
IPv6 Del.Pfx. Origin : Radius
IPv6 Del.Pfx. Pool : ""
IPv6 Address : 2001:db8:a:101::aaa:1
IPv6 Address Origin : Radius
IPv6 Address Pool : ""
Primary IPv6 DNS : N/A
Secondary IPv6 DNS : N/A
Radius Session-TO : N/A
Radius Class :
Radius User-Name : 00:51:00:00:00:0c
Subscriber Host Limit Overrides
ipv4-arp : 1
ipv4-dhcp : 1
ipv4-ppp : 1
ipv4-overall : 1
ipv6-pd-ipoe-dhcp : 1
ipv6-pd-ppp-dhcp : 1
ipv6-pd-overall : 1
ipv6-wan-ipoe-dhcp : 1
ipv6-wan-ipoe-slaac : 1
ipv6-wan-ppp-dhcp : 1
ipv6-wan-ppp-slaac : 1
ipv6-wan-overall : 1
ipv6-overall : 1
lac-overall : 1
overall : 1
SLA Profile Instance Host Limit Overrides
ipv4-arp : 1
ipv4-dhcp : 1
ipv4-ppp : 1
ipv4-overall : 1
ipv6-pd-ipoe-dhcp : 1
ipv6-pd-ppp-dhcp : 1
ipv6-pd-overall : 1
ipv6-wan-ipoe-dhcp : 1
ipv6-wan-ipoe-slaac : 1
ipv6-wan-ppp-dhcp : 1
ipv6-wan-ppp-slaac : 1
ipv6-wan-overall : 1
ipv6-overall : 1
lac-overall : 1
overall : 1
Subscriber Session Limit Overrides
ipoe : 1
pppoe-local : 1
pppoe-lac : 1
pppoe-overall : 1
l2tp-lns : 1
l2tp-lts : 1
l2tp-overall : 1
overall : 1
SLA Profile Instance Session Limit Overrides
ipoe : 1
pppoe-local : 1
pppoe-lac : 1
pppoe-overall : 1
l2tp-lns : 1
l2tp-lts : 1
l2tp-overall : 1
overall : 1
-------------------------------------------------------------------------------
Number of sessions : 1
===============================================================================
*A:Dut-A# show service id 13 ipoe session router-advertisement-policy ra-policy-01
===============================================================================
IPoE sessions for svc-id 13
===============================================================================
Sap Id Mac Address Up Time MC-Stdby
Subscriber-Id
[CircuitID] | [RemoteID]
-------------------------------------------------------------------------------
1/1/1:13 00:00:00:00:00:13 0d 00:13:06
sub-1
1/1/1:13 00:00:00:00:00:14 0d 00:08:03
sub-1
1/1/1:13 00:00:00:00:00:15 0d 00:06:23
sub-1
-------------------------------------------------------------------------------
CID | RID displayed when included in session-key
Number of sessions : 3
===============================================================================
*A:Dut-A#
Service IPoE Session Field Descriptions describes IPoE session field information.
Field |
Description |
---|---|
SAP Id |
The SAP ID of the IPoE session |
Mac Address |
The MAC address of the IPoE session |
Up Time |
The time of the last modification |
MC-Stdby |
The number of SAPs defined on this service on a port which is in multi-chassis standby mode |
SAP |
The SAP ID of the IPoE session |
Circuit-Id |
The circuit ID of the IPoE session |
Remote-Id |
The remote ID of the IPoE session |
Session Key |
The session key used for this IPoE session to group subscriber hosts |
MC-Standby |
The number of SAPs defined on this service on a port which is in multi-chassis standby mode |
Subscriber-interface |
The subscriber interface name |
Group-interface |
The group interface name |
Up Time |
The time of the last modification |
Session Time Left |
The time remaining for the session timeout |
Last Auth Time |
The date and time of the last authentication |
Min Auth Intvl (left) |
The minimum interval between two consecutive authentication attempts for the same ARP host |
Persistence Key |
The key value that is used to track this in the persistence file |
Subscriber |
The subscriber identification string |
Sub-Profile-String |
The subscriber profile name |
SLA-Profile-String |
The SLA profile name |
ANCP-String |
The value of the ancp-string received from either the DHCP or the RADIUS server |
Int-Dest-Id |
Intermediate destination identifier received from the RADIUS server |
App-Profile-String |
The application profile string |
Category-Map-Name |
The value of the category map name received from the RADIUS server |
Acct-Session-Id |
The accounting session ID |
Sap-Session-Index |
The sap session index of the PPP session |
IP Address |
The IP address |
IP Origin |
The origin of the source IP address used for connectivity verification |
Primary DNS |
The primary DNS server |
Secondary DNS |
The secondary DNS server |
Primary NBNS |
The primary NBNS server |
Secondary NBNS |
The secondary NBNS server |
Address-Pool |
The IP address pool used to search for an IP address for this session |
IPv6 Prefix |
The IPv6 prefix |
IPv6 Prefix Origin |
The origin of the IPv6 prefix |
IPv6 Prefix Pool |
The DHCP server pool from which the SLAAC prefix is allocated |
IPv6 Del.Pfx. |
The IPv6 delegated prefix |
IPv6 Del.Pfx. Origin |
The origin of the IPv6 delegated prefix |
IPv6 Del.Pfx. Pool |
The DHCP server pool from which the delegated prefix is allocated |
IPv6 Address |
The IPv6 address |
IPv6 Address Origin |
The origin of the IPv6 address |
IPv6 Address Pool |
The DHCP server pool from which the address is allocated |
Primary IPv6 DNS |
The primary DNS server |
Secondary IPv6 DNS |
The secondary DNS server |
Radius Session-TO |
The value to interpret the session timeout VSA from RADIUS |
Radius Class |
The Class attribute returned by the RADIUS server in an Access-Accept message |
Radius User-Name |
The User-Name attribute returned by the RADIUS server in an Access-Accept message |
Subscriber Host Limit Overrides and SLA Profile Instance Host Limit Overrides: |
|
ipv4-arp |
The total number of IPv4 ARP hosts limit |
ipv4-dhcp |
The total number of IPv4 DHCP hosts limit |
ipv4-ppp |
The total number of IPv4 PPP hosts limit |
ipv4-overall |
The total number of IPv4 hosts limit |
ipv6-pd-ipoe-dhcp |
The total number of IPv6 IPoE DHCP Prefix Delegation hosts (IA-PD) limit |
ipv6-pd-ppp-dhcp |
The total number of IPv6 PPPoE DHCP Prefix Delegation hosts (IA-PD) limit |
ipv6-pd-overall |
The total number of IPv6 DHCP Prefix Delegation hosts (IA-PD) limit |
ipv6-wan-ipoe-dhcp |
The total number of IPv6 IPoE DHCP WAN hosts (IA-NA) limit |
ipv6-wan-ipoe-slaac |
The total number of IPv6 IPoE SLAAC WAN hosts limit |
ipv6-wan-ppp-dhcp |
The total number of IPv6 PPPoE DHCP WAN hosts (IA-NA) limit |
ipv6-wan-ppp-slaac |
The total number of IPv6 PPPoE SLAAC WAN hosts limit |
ipv6-wan-overall |
The total number of IPv6 WAN hosts limit |
ipv6-overall |
The total number of IPv6 hosts limit |
lac-overall |
The total number of L2TP LAC hosts limit |
overall |
The total number of subscriber hosts limit |
Subscriber Session Limit Overrides and SLA Profile Instance Session Limit Overrides: |
|
ipoe |
The total number of IPoE sessions limit |
ppoe-local |
The total number of PPPoE local terminated sessions (PTA) limit |
ppoe-lac |
The total number of PPPoE L2TP LAC sessions limit |
ppoe-overall |
The total number of PPPoE sessions limit |
l2tp-lns |
The total number of L2TP LNS sessions limit |
l2tp-lts |
The total number of L2TP LTS sessions limit |
l2tp-overall |
The total number of L2TP sessions limit |
overall |
The total number of subscriber sessions limit |
Number of session |
The number of sessions returned from the search criteria |
session
Syntax
session [name trace-name] [detail]
session sap sap-id mac ieee-address [circuit-id circuit-id] [remote-id remote-id] [username user-name] [detail]
Context
[Tree] (show>call-trace>ppp session)
[Tree] (show>call-trace>ipoe session)
Full Context
show call-trace ppp session
show call-trace ipoe session
Description
This command displays call trace information for the active session.
Configuring this command with specified session filters, displays information for the specified trace job only.
Parameters
- detail
-
Displays detailed information.
- sap-id
-
Specifies the SAP ID that identifies a session.
- ieee-address
-
Specifies a MAC address that identifies a session.
- circuit-id
-
Specifies a circuit ID that identifies a session, up to 255 characters.
- remote-id
-
Specifies a remote ID that identifies a session, up to 255 characters.
- trace-name
-
Specifies the name of the trace, up to 32 characters, that triggered the job.
- user-name
-
Specifies the user name, up to 32 characters, that identifies a PPPoE session.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of call trace information for the active IPoE session.
Output ExampleNode # show call-trace ipoe session
=========================================================
Call trace IPoE session
=========================================================
IEEE address Status No. of messages
Trace name
---------------------------------------------------------
00:02:00:00:00:19 running 10
default
---------------------------------------------------------
No. of call trace IPoE debug jobs: 1
=========================================================
Node# show call-trace ipoe session detail
===============================================================================
Call trace IPoE session
===============================================================================
SAP ID : 4/1/ 2
IEEE address: 00:02:00:00:00:19
Trace name : default Status : running
Size limit : 10 MB Time limit : 86400 sec
Live output
-------------------------------------------------------------------------------
Destination : none
Statistics
-------------------------------------------------------------------------------
Started : 2017/01/11 15:34:08UTC
No. of captured msgs : 10
Size of captured msgs : 2575 B
===============================================================================
Call Trace IPoE Session Field Descriptions describes call trace IPoE session output fields.
Field |
Description |
---|---|
IEEE address |
The IEEE address of the equipment to match by this trace |
Status |
The status of the trace session |
No. of messages |
The number of messages from the trace session |
Trace name |
The name of the trace profile |
Size limit |
The maximum data volume generated by a single call trace job to the output, in megabytes |
Time limit |
The maximum duration of a single call trace job, in seconds |
Live output |
The live output destination for trace logs |
Destination |
The destination address of the trace logs |
Started |
The date and time the trace began |
No. of captured msgs |
The number of captured messages |
Size of captured msgs |
The size of the captured messages |
session
Syntax
session sap sap-id mac ieee-address
session sap sap-id mac ieee-address circuit-id circuit-id [remote-id remote-id] [user-name user-name]
session sap sap-id mac ieee-address [circuit-id circuit-id] remote-id remote-id [user-name user-name]
session sap sap-id mac ieee-address [circuit-id circuit-id] [ remote-id remote-id] user-name user-name
Context
[Tree] (clear>call-trace>ipoe session)
[Tree] (clear>call-trace>pppoe session)
Full Context
clear call-trace ipoe session
clear call-trace pppoe session
Description
This command clears the trace job identified by this session.
This command does not affect any of the debug trace commands, and new jobs can still be executed for other sessions.
After a session is cleared, tracing for the session will not be restarted by any configured trace. Only explicitly starting a new trace with the trace-existing-sessions parameter can restart tracing for the session.
Parameters
- circuit-id
-
Specifies a circuit ID, up to 255 characters, that identifies a session.
- ieee-address
-
Specifies a MAC address that identifies a session.
- remote-id
-
Specifies a remote ID, up to 255 characters, that identifies a session
- sap-id
-
Specifies the SAP ID that identifies a session.
- user-name
-
Specifies the user name, up to 32 characters, that identifies a session.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
session
Syntax
session [family] [summary | detail] ip-addr[label-space]
Context
[Tree] (show>router>ldp>bindings session)
Full Context
show router ldp bindings session
Description
This command displays LDP FEC bindings by matching peer LSR ID.
Parameters
- detail
-
Displays detailed information.
- summary
-
Displays information in a summarized format.
- family
-
Displays either IPv4 or IPv6 LDP session information.
- ip-addr
-
displays configuration information about LDP sessions.
- label-space
-
Specifies the label space identifier that the router is advertising on the interface.
Platforms
All
session
Syntax
session [ip-addr [label-space]] local-addresses [sent | recv] ip-addr ip-address
session [ip-addr [label-space]] [session-type] [state state] [summary | detail] [community community]
session [ip-addr [label-space]] local-addresses [sent | recv] [family]
session [ip-addr [label-space]] [sent | recv] overload [fec-type fec-type]
session [sent | recv] overload [ fec-type fec-type] [family] [ community community]
session [ip-addr [label-space]] statistics [packet-type] [session-type]
session statistics [packet-type] [session-type] [family]
session [session-type] [state state] [summary | detail] [family] [community community]
Context
[Tree] (show>router>ldp session)
Full Context
show router ldp session
Description
This command displays configuration information about LDP sessions.
Parameters
- ip-addr
-
Specifies the IP address of the LDP peer.
- label-space
-
Specifies the label space identifier that the router is advertising on the interface.
- statistics
-
Specifies the statistics for a targeted peer.
- packet-type
-
Specifies the packet type.
- session-type
-
Specifies to display the session type.
- state
-
Specifies to display the current operational state of the adjacency.
- summary
-
Displays information in a summarized format.
- detail
-
Displays detailed information including the community and if a local LSR ID is advertised.
- local-addresses
-
Specifies the local address information.
- ip-address
-
Specifies the IPv4 or IPv6 address.
- overload
-
Specifies the overload information.
- fec-type
-
Specifies the specified FEC type.
- family
-
Displays either IPv4 or IPv6 active LDP information.
- community
-
The string defining the LDP community assigned to the session. Allowed values are any string up to 32 characters long composed of printable, 7-bit ASCII characters excluding double quotes. If the string contains spaces, use double quotes to delimit the start and end of the string.
Platforms
All
Output
LDP Session Output Fields describes the LDP session output fields.
Label |
Description |
---|---|
Peer LDP Id |
The IP address of the LDP peer. |
Adj Type |
The adjacency type between the LDP peer and LDP session is targeted. |
Link — Specifies that this adjacency is a result of a link hello. Targeted — Specifies that this adjacency is a result of a targeted hello. |
|
State |
Established — Specifies that the adjacency is established. Trying — Specifies that the adjacency is not yet established. |
Msg Sent Mesg Sent |
The number of messages sent. |
Msg Rcvd Mesg Rcvd |
The number of messages received. |
Up Time |
The amount of time the adjacency has been enabled. |
Session Community |
Specifies the LDP community associated with a session. |
Local LSR ID Advertised |
Specifies if a local LSR ID is advertised. |
*A:Dut-A# show router ldp session
==============================================================================
LDP IPv4 Sessions
==============================================================================
Peer LDP Id Adj Type State Msg Sent Msg Recv Up Time
------------------------------------------------------------------------------
10.20.1.2:0 Link Established 1724 1725 0d 01:16:29
10.20.1.3:0 Link Established 1721 1723 0d 01:16:24
10.20.1.6:0 Targeted Established 1237 1238 0d 00:54:53
------------------------------------------------------------------------------
No. of IPv4 Sessions: 3
==============================================================================
===============================================================================
LDP IPv6 Sessions
===============================================================================
Peer LDP Id
Adj Type State Msg Sent Msg Recv Up Time
-------------------------------------------------------------------------------
3ffe::a14:102[0]
Link Established 1718 1721 0d 01:16:10
3ffe::a14:103[0]
Link Established 1718 1717 0d 01:16:10
3ffe::a14:106[0]
Targeted Established 598 598 0d 00:53:07
-------------------------------------------------------------------------------
No. of IPv6 Sessions: 3
===============================================================================
*A:Dut-A#
*A:Dut-A# show router ldp session ipv6
===============================================================================
LDP IPv6 Sessions
===============================================================================
Peer LDP Id
Adj Type State Msg Sent Msg Recv Up Time
-------------------------------------------------------------------------------
10.10.2.3:0
Targeted Established 29 31 0d 00:00:57
3ffe::a14:102[0]
Link Established 37646 37642 1d 03:55:39
3ffe::a14:103[0]
Link Established 37653 37675 1d 03:55:36
-------------------------------------------------------------------------------
No. of IPv6 Sessions: 3
===============================================================================
*A:Dut-A# show router ldp session 10.20.1.2
==============================================================================
LDP IPv4 Sessions
==============================================================================
Peer LDP Id Adj Type State Msg Sent Msg Recv Up Time
------------------------------------------------------------------------------
10.20.1.2:0 Link Established 1728 1729 0d 01:16:42
------------------------------------------------------------------------------
No. of IPv4 Sessions: 1
==============================================================================
*A:Dut-A# show router ldp session 10.10.2.3 detail
===============================================================================
LDP IPv4 Sessions (Detail)
===============================================================================
Legend: DoD - Downstream on Demand (for address FEC's only)
DU - Downstream Unsolicited
R - Capability value received from peer
===============================================================================
-------------------------------------------------------------------------------
Session with Peer 10.20.1.1:0, Local 10.20.1.4:0
-------------------------------------------------------------------------------
Adjacency Type : Targeted State : Established
Up Time : 3d 21:54:43
Max PDU Length : 4096 KA/Hold Time Remaining : 121
Link Adjacencies : 0 Targeted Adjacencies : 1
Local Address : 10.20.1.4 Peer Address : 10.20.1.1
Local UDP Port : 646 Peer UDP Port : 646
Local TCP Port : 55190 Peer TCP Port : 646
Local KA Timeout : 140 Peer KA Timeout : 140
Mesg Sent : 219023 Mesg Recv : 127264
IPv4 Pfx FEC Sent : 2092 IPv4 Pfx FEC Recv : 1655
IPv6 Pfx FEC Sent : 0 IPv6 Pfx FEC Recv : 0
IPv4 P2MP FEC Sent : 0 IPv4 P2MP FEC Recv : 0
IPv6 P2MP FEC Sent : 0 IPv6 P2MP FEC Recv : 0
Svc Fec128 Sent : 0 Svc Fec128 Recv : 0
Svc Fec129 Sent : 0 Svc Fec129 Recv : 0
IPv4 Addrs Sent : 1013 IPv4 Addrs Recv : 2996
IPv6 Addrs Sent : 119 IPv6 Addrs Recv : 833
Local GR State : Capable Peer GR State : Capable
Local Nbr Liveness Time: 5 Peer Nbr Liveness Time : 0
Local Recovery Time : 30 Peer Recovery Time : 0
Number of Restart : 0 Last Restart Time : Never
Label Distribution : DU
Oper Fec Limit Thresho*: 0
Local-LSR ID advertise : Enabled
Community : RED
Capabilities
Local P2MP : Capable Peer P2MP : Capable
Local MP MBB : Capable Peer MP MBB : Capable
Local Dynamic : Capable Peer Dynamic : Capable
Local LSR Overload : Not Capable Peer LSR Overload : Capable
Local IPv4 Pfx : Capable Peer IPv4 Pfx : Capable (R)
Local IPv6 Pfx : Not Capable Peer IPv6 Pfx : Not Capable (*
Local SvcFec128 : Capable Peer SvcFec128 : Capable (R)
Local SvcFec129 : Capable Peer SvcFec129 : Capable (R)
Local UnregNoti : Capable Peer UnregNoti : Capable
Advertise : Address/Servi*
IPv4 PfxFecOLoad Sent : No IPv4 PfxFecOLoad Recv : No
IPv6 PfxFecOLoad Sent : No IPv6 PfxFecOLoad Recv : No
IPv4 P2MPFecOLoad Sent : No IPv4 P2MPFecOLoad Recv : No
IPv6 P2MPFecOLoad Sent : No IPv6 P2MPFecOLoad Recv : No
Svc Fec128 OLoad Sent : No Svc Fec128 OLoad Recv : No
Svc Fec129 OLoad Sent : No Svc Fec129 OLoad Recv : No
IPv4 PfxFec EOL Sent : Yes IPv4 PfxFec EOL Recv : Yes
IPv6 PfxFec EOL Sent : No IPv6 PfxFec EOL Recv : No
IPv4 P2MPFec EOL Sent : No IPv4 P2MPFec EOL Recv : No
IPv6 P2MPFec EOL Sent : No IPv6 P2MPFec EOL Recv : No
Svc Fec128 EOL Sent : Yes Svc Fec128 EOL Recv : Yes
Svc Fec129 EOL Sent : Yes Svc Fec129 EOL Recv : Yes
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
LDP IPv6 Sessions (Detail)
===============================================================================
Legend: DoD - Downstream on Demand (for address FEC's only)
DU - Downstream Unsolicited
R - Capability value received from peer
===============================================================================
No Matching Entries Found
===============================================================================
*A:SRU4# show router ldp session community RED
==============================================================================
LDP IPv4 Sessions
==============================================================================
Peer LDP Id Adj Type State Msg Sent Msg Recv Up Time
------------------------------------------------------------------------------
10.100.1.1:0 Link Established 327423 256220 3d 22:03:37
10.20.1.1.1:0 Targeted Established 219040 127266 3d 21:55:33
10.20.1.2:0 Targeted Established 365925 407096 3d 22:38:34
10.20.1.5:0 Targeted Established 359363 424352 3d 21:54:55
10.20.1.6:0 Both Established 1043697 1668727 3d 21:32:17
10.20.1.9:0 Targeted Established 507123 630800 3d 22:25:57
10.20.1.10:0 Targeted Established 320141 269052 3d 21:34:08
10.20.1.11:0 Targeted Established 284934 180483 3d 22:18:21
------------------------------------------------------------------------------
No. of IPv4 Sessions: 8
==============================================================================
===============================================================================
LDP IPv6 Sessions
===============================================================================
Peer LDP Id
Adj Type State Msg Sent Msg Recv Up Time
-------------------------------------------------------------------------------
No Matching Entries Found
===============================================================================
-------------------------------------------------------------------------------
Session with Peer 10.10.2.3:0, Local 10.10.2.1:0
-------------------------------------------------------------------------------
Adjacency Type : Targeted State : Established
Up Time : 0d 00:01:16
Max PDU Length : 4096 KA/Hold Time Remaining : 28
Link Adjacencies : 0 Targeted Adjacencies : 1
Local Address : 3ffe::a0a:201 Peer Address : 3ffe::a0a:203
Local UDP Port : 646 Peer UDP Port : 646
Local TCP Port : 646 Peer TCP Port : 646
Local KA Timeout : 30 Peer KA Timeout : 30
Mesg Sent : 36 Mesg Recv : 37
IPv4 Pfx FEC Sent : 0 IPv4 Pfx FEC Recv : 0
IPv6 Pfx FEC Sent : 0 IPv6 Pfx FEC Recv : 0
IPv4 P2MP FEC Sent : 0 IPv4 P2MP FEC Recv : 0
IPv6 P2MP FEC Sent : 0 IPv6 P2MP FEC Recv : 0
Svc Fec128 Sent : 1 Svc Fec128 Recv : 1
Svc Fec129 Sent : 0 Svc Fec129 Recv : 0
IPv4 Addrs Sent : 3 IPv4 Addrs Recv : 6
IPv6 Addrs Sent : 3 IPv6 Addrs Recv : 6
Local GR State : Not Capable Peer GR State : Not Capable
Local Nbr Liveness Time: 0 Peer Nbr Liveness Time : 0
Local Recovery Time : 0 Peer Recovery Time : 0
Number of Restart : 0 Last Restart Time : Never
Label Distribution : DU
Oper Fec Limit Thresho*: 0
Local-LSR ID advertise : Disabled
Community :
Capabilities
Local P2MP : Capable Peer P2MP : Capable
Local MP MBB : Capable Peer MP MBB : Capable
Local Dynamic : Capable Peer Dynamic : Capable
Local LSR Overload : Capable Peer LSR Overload : Capable
Local IPv4 Pfx : Capable Peer IPv4 Pfx : Capable
Local IPv6 Pfx : Capable Peer IPv6 Pfx : Capable
Local SvcFec128 : Capable Peer SvcFec128 : Capable
Local SvcFec129 : Capable Peer SvcFec129 : Capable
Local UnregNoti : Capable Peer UnregNoti : Capable
Advertise : Service
IPv4 PfxFecOLoad Sent : No IPv4 PfxFecOLoad Recv : No
IPv6 PfxFecOLoad Sent : No IPv6 PfxFecOLoad Recv : No
IPv4 P2MPFecOLoad Sent : No IPv4 P2MPFecOLoad Recv : No
IPv6 P2MPFecOLoad Sent : No IPv6 P2MPFecOLoad Recv : No
Svc Fec128 OLoad Sent : No Svc Fec128 OLoad Recv : No
Svc Fec129 OLoad Sent : No Svc Fec129 OLoad Recv : No
IPv4 PfxFec EOL Sent : No IPv4 PfxFec EOL Recv : No
IPv6 PfxFec EOL Sent : No IPv6 PfxFec EOL Recv : No
IPv4 P2MPFec EOL Sent : No IPv4 P2MPFec EOL Recv : No
IPv6 P2MPFec EOL Sent : No IPv6 P2MPFec EOL Recv : No
Svc Fec128 EOL Sent : Yes Svc Fec128 EOL Recv : Yes
Svc Fec129 EOL Sent : Yes Svc Fec129 EOL Recv : Yes
===============================================================================
* indicates that the corresponding row element may have been truncated.
==============================================================================
*A:Dut-A# show router ldp session 3ffe::a14:106
===============================================================================
LDP IPv6 Sessions
===============================================================================
Peer LDP Id
Adj Type State Msg Sent Msg Recv Up Time
-------------------------------------------------------------------------------
3ffe::a14:106[0]
Targeted Established 601 602 0d 00:53:28
-------------------------------------------------------------------------------
No. of IPv6 Sessions: 1
===============================================================================
*A:Dut-A# show router ldp session 10.20.1.2 local-addresses
===============================================================================
LDP Session Local-Addresses
===============================================================================
-------------------------------------------------------------------------------
Session with Peer 10.20.1.2:0,
Local 10.20.1.1:0
-------------------------------------------------------------------------------
IPv4 Sent Addresses:
10.10.1.1 10.10.2.1 10.20.1.1
IPv6 Sent Addresses:
3ffe::a0a:101
3ffe::a0a:201
3ffe::a14:101
fe80::11
IPv4 Recv Addresses:
10.10.1.2 10.10.3.2 10.10.4.2 10.10.12.2
10.20.1.2
IPv6 Recv Addresses:
3ffe::a0a:102
3ffe::a0a:302
3ffe::a0a:402
3ffe::a0a:c02
3ffe::a14:102
fe80::12
===============================================================================
*A:Dut-A# show router ldp session 10.20.1.2 local-addresses sent
===============================================================================
LDP Session Local-Addresses
===============================================================================
-------------------------------------------------------------------------------
Session with Peer 10.20.1.2:0,
Local 10.20.1.1:0
-------------------------------------------------------------------------------
IPv4 Sent Addresses:
10.10.1.1 10.10.2.1 10.20.1.1
IPv6 Sent Addresses:
3ffe::a0a:101
3ffe::a0a:201
3ffe::a14:101
fe80::11
===============================================================================
*A:Dut-A# show router ldp session 10.20.1.2 local-addresses recv
===============================================================================
LDP Session Local-Addresses
===============================================================================
-------------------------------------------------------------------------------
Session with Peer 10.20.1.2:0,
Local 10.20.1.1:0
-------------------------------------------------------------------------------
IPv4 Recv Addresses:
10.10.1.2 10.10.3.2 10.10.4.2 10.10.12.2
10.20.1.2
IPv6 Recv Addresses:
3ffe::a0a:102
3ffe::a0a:302
3ffe::a0a:402
3ffe::a0a:c02
3ffe::a14:102
fe80::12
===============================================================================
*A:Dut-A#
*A:Dut-A# show router ldp session 10.20.1.2 local-addresses recv ip-
addr 3ffe::a14:102
===============================================================================
LDP Session Local-Addresses
===============================================================================
-------------------------------------------------------------------------------
Session with Peer 10.20.1.2:0,
Local 10.20.1.1:0
-------------------------------------------------------------------------------
IPv6 Recv Addresses:
3ffe::a14:102
===============================================================================
*A:Dut-A#
*A:Dut-A# show router ldp session 10.20.1.2 link summary
No. of IPv4 Sessions: 1
*A:Dut-A#
*A:Dut-A# show router ldp session link
==============================================================================
LDP IPv4 Sessions
==============================================================================
Peer LDP Id Adj Type State Msg Sent Msg Recv Up Time
------------------------------------------------------------------------------
10.20.1.2:0 Link Established 1794 1796 0d 01:19:38
10.20.1.3:0 Link Established 1792 1794 0d 01:19:33
------------------------------------------------------------------------------
No. of IPv4 Sessions: 2
==============================================================================
===============================================================================
LDP IPv6 Sessions
===============================================================================
Peer LDP Id
Adj Type State Msg Sent Msg Recv Up Time
-------------------------------------------------------------------------------
3ffe::a14:102[0]
Link Established 1788 1792 0d 01:19:19
3ffe::a14:103[0]
Link Established 1789 1788 0d 01:19:19
-------------------------------------------------------------------------------
No. of IPv6 Sessions: 2
===============================================================================
*A:Dut-A# show router ldp session link summary
No. of IPv4 Sessions: 2
No. of IPv6 Sessions: 2
*A:Dut-A#
*A:Dut-A# show router ldp session state up link
==============================================================================
LDP IPv4 Sessions
==============================================================================
Peer LDP Id Adj Type State Msg Sent Msg Recv Up Time
------------------------------------------------------------------------------
10.20.1.2:0 Link Established 1805 1807 0d 01:20:08
10.20.1.3:0 Link Established 1803 1805 0d 01:20:03
------------------------------------------------------------------------------
No. of IPv4 Sessions: 2
==============================================================================
===============================================================================
LDP IPv6 Sessions
===============================================================================
Peer LDP Id
Adj Type State Msg Sent Msg Recv Up Time
-------------------------------------------------------------------------------
3ffe::a14:102[0]
Link Established 1799 1803 0d 01:19:49
3ffe::a14:103[0]
Link Established 1799 1799 0d 01:19:49
-------------------------------------------------------------------------------
No. of IPv6 Sessions: 2
===============================================================================
*A:Dut-A#
*A:Dut-A# show router ldp session summary
No. of IPv4 Sessions: 3
No. of IPv6 Sessions: 3
*A:Dut-A#
*A:Dut-A# show router ldp session local-addresses ipv4
===============================================================================
LDP Session Local-Addresses
===============================================================================
-------------------------------------------------------------------------------
Session with Peer 10.20.1.2:0,
Local 10.20.1.1:0
-------------------------------------------------------------------------------
IPv4 Sent Addresses:
10.10.1.1 10.10.2.1 10.20.1.1
IPv4 Recv Addresses:
10.10.1.2 10.10.3.2 10.10.4.2 10.10.12.2
10.20.1.2
-------------------------------------------------------------------------------
Session with Peer 10.20.1.3:0,
Local 10.20.1.1:0
-------------------------------------------------------------------------------
IPv4 Sent Addresses:
10.10.1.1 10.10.2.1 10.20.1.1
IPv4 Recv Addresses:
10.10.2.3 10.10.3.3 10.10.5.3 10.10.11.3
10.10.12.3 10.20.1.3
-------------------------------------------------------------------------------
Session with Peer 10.20.1.6:0,
Local 10.20.1.1:0
-------------------------------------------------------------------------------
IPv4 Sent Addresses:
10.10.1.1 10.10.2.1 10.20.1.1
IPv4 Recv Addresses:
10.10.9.6 10.10.10.6 10.20.1.6
-------------------------------------------------------------------------------
Session with Peer 3ffe::a14:102[0],
Local 3ffe::a14:101[0]
-------------------------------------------------------------------------------
IPv4 Sent Addresses:
10.10.1.1 10.10.2.1 10.20.1.1
IPv4 Recv Addresses:
10.10.1.2 10.10.3.2 10.10.4.2 10.10.12.2
10.20.1.2
-------------------------------------------------------------------------------
Session with Peer 3ffe::a14:103[0],
Local 3ffe::a14:101[0]
-------------------------------------------------------------------------------
IPv4 Sent Addresses:
10.10.1.1 10.10.2.1 10.20.1.1
IPv4 Recv Addresses:
10.10.2.3 10.10.3.3 10.10.5.3 10.10.11.3
10.10.12.3 10.20.1.3
-------------------------------------------------------------------------------
Session with Peer 3ffe::a14:106[0],
Local 3ffe::a14:101[0]
-------------------------------------------------------------------------------
IPv4 Sent Addresses:
10.10.1.1 10.10.2.1 10.20.1.1
IPv4 Recv Addresses:
10.10.9.6 10.10.10.6 10.20.1.6
===============================================================================
*A:Dut-A#
*A:Dut-A# show router ldp session 10.20.1.2 statistics
===============================================================================
LDP IPv4 Session Statistics
===============================================================================
Message Type Sent Received
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Session 10.20.1.2:0
-------------------------------------------------------------------------------
Hello 1298 1300
Keepalive 545 545
Init 1 1
Label Mapping 5 5
Label Request 0 0
Label Release 0 0
Label Withdraw 0 0
Label Abort 0 0
Notification 1 1
Address 3 3
Address Withdraw 1 1
Capability 0 0
===============================================================================
*A:Dut-A#
*A:Dut-A# show router ldp session 10.20.1.2 statistics hello
===============================================================================
LDP IPv4 Session Statistics
===============================================================================
Message Type Sent Received
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Session 10.20.1.2:0
-------------------------------------------------------------------------------
Hello 1303 1305
===============================================================================
*A:Dut-A# show router ldp session 10.20.1.2 statistics keepalive
===============================================================================
LDP IPv4 Session Statistics
===============================================================================
Message Type Sent Received
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Session 10.20.1.2:0
-------------------------------------------------------------------------------
Keepalive 547 547
===============================================================================
*A:Dut-A#
session
Syntax
session ip-addr [label-space] [statistics]
session ip-addr [label-space] overload [fec-type p2mp | prefixes sub-type sub-type]
session ip-addr[label-space] overload [fec-type svc-fec128 | svc-fec129]
Context
[Tree] (clear>router>ldp session)
Full Context
clear router ldp session
Description
This command restarts or clears statistics for LDP sessions.
Parameters
- ip-address
-
Clears the IP address of the session
- label-space
-
Specifies the label space identifier that the router is advertising on the interface.
- statistics
-
Clears only the statistics for a session.
- overload
-
Clears overload information.
- fec-type
-
Clears the specified FEC type.
- session ip-addr[label-space]
-
Specifies the IP address and label space identifier.
Platforms
All
session
Syntax
session ip-addr[label-space] [connection | peer | adjacency]
Context
[Tree] (tools>dump>router>ldp session)
Full Context
tools dump router ldp session
Description
This command dumps information for an LDP session.
Parameters
- ip-addr[label-space]
-
Dumps information for the specified IP address and label space identifier.
- connection
-
Filters output for connection information.
- peer
-
Filters output for peering information.
- adjacency
-
Filters output for adjacency information.
Platforms
All
session
Syntax
session lsp-index lsp-index [path-lspid path-lspid] [detail]
session lsp-name lsp-name [path-lspid path-lspid] [detail]
session lsp-path [detail]
session lsp-path prefix ip-prefix /prefix-length [src ip-address /local-link address] [detail]
session sr-policy [detail]
session sr-policy prefix ip-prefix /prefix-length [src ip-address /local-link address] [detail]
Context
[Tree] (show>router>bfd>seamless-bfd session)
Full Context
show router bfd seamless-bfd session
Description
This command displays Seamless-BFD session information.
Parameters
- lsp-index lsp-index
-
Specifies the LSP index.
- path-lspid path-lspid
-
Specifies the path LSP ID.
- detail
-
Displays detailed information.
- lsp-name lsp-name
-
Displays information about the specified LSP name, up to 64 characters.
- lsp-path
-
Keyword to display information by LSP path.
- prefix
-
Keyword to display information by far-end prefix.
- sr-policy
-
Keyword to display information by SR policy.
- ip-prefix/prefix-length
-
Specifies an IP prefix for which to display Seamless-BFD session information, and the length of the prefix.
- ip-address/link-local-address
-
Specifies the source IP address for which to display Seamless-BFD session information.
Platforms
All
Output
The following output is an example of BFD session information and MPLS Seamless-BFD Session Output Fields describes Seamless-BFD session output fields.
Output Example# show router bfd seamless-bfd session lsp-index 70000
===============================================================================
Legend:
Session Id = Interface Name | LSP Name | Prefix | RSVP Sess Name | Service Id
wp = Working path pp = Protecting path
===============================================================================
BFD Session
===============================================================================
Session Id State Tx Pkts Rx Pkts
Rem Addr/Info/SdpId:VcId Multipl Tx Intvl Rx Intvl
Protocols Type LAG Port LAG ID
-------------------------------------------------------------------------------
10.20.1.6/32 Up N/A N/A
10.20.1.6 3 10 10
mplsLsp cpm-np N/A N/A
-------------------------------------------------------------------------------
No. of BFD sessions: 1
===============================================================================
# show router bfd seamless-bfd session lsp-name "C_F_70000"
===============================================================================
Legend:
Session Id = Interface Name | LSP Name | Prefix | RSVP Sess Name | Service Id
wp = Working path pp = Protecting path
===============================================================================
BFD Session
===============================================================================
Session Id State Tx Pkts Rx Pkts
Rem Addr/Info/SdpId:VcId Multipl Tx Intvl Rx Intvl
Protocols Type LAG Port LAG ID
-------------------------------------------------------------------------------
10.20.1.6/32 Up N/A N/A
10.20.1.6 3 10 10
mplsLsp cpm-np N/A N/A
-------------------------------------------------------------------------------
No. of BFD sessions: 1
====================================
The following show output displays an LSP that has BFD configured to use a controlled return path.
# show router bfd seamless-bfd session lsp-path detail
===============================================================================
BFD Session
===============================================================================
Prefix : 10.20.1.6/32
Local Address : 10.20.1.3
LSP Name : C_F_70000
LSP Index : 70000 Path LSP ID : 62976
Fec Type : srTe
Return Path : 454600
Oper State : Up Protocols : mplsLsp
Up Time : 0d 00:00:12 Up Transitions : 1
Down Time : None Down Transitions : 0
Version Mismatch : 0
Forwarding Information
Local Discr : 1 Local State : Up
Local Diag : 0 (None)
Local Mode : Demand
Local Min Tx : 1000 Local Mult : 3
Last Sent (ms) : 0 Local Min Rx : 1000
Type : cpm-np
Remote Discr : 524293 Remote State : Up
Remote Diag : 0 (None) Remote Mode : Demand
Remote Min Tx : 1000 Remote Mult : 3
Remote C-flag : 1
Last Recv (ms) : 0 Remote Min Rx : 3
===============================================================================
# show router bfd seamless-bfd session lsp-path prefix 10.20.1.6/32
===============================================================================
Legend:
Session Id = Interface Name | LSP Name | Prefix | RSVP Sess Name | Service Id
wp = Working path pp = Protecting path
===============================================================================
BFD Session
===============================================================================
Session Id State Tx Pkts Rx Pkts
Rem Addr/Info/SdpId:VcId Multipl Tx Intvl Rx Intvl
Protocols Type LAG Port LAG ID
-------------------------------------------------------------------------------
10.20.1.6/32 Up N/A N/A
10.20.1.6 3 10 10
mplsLsp cpm-np N/A N/A
-------------------------------------------------------------------------------
No. of BFD sessions: 1
===============================================================================
# show router bfd seamless-bfd session sr-policy
===============================================================================
Legend:
Session Id = Interface Name | LSP Name | Prefix | RSVP Sess Name | Service Id
wp = Working path pp = Protecting path
===============================================================================
BFD Session
===============================================================================
Session Id State Tx Pkts Rx Pkts
Rem Addr/Info/SdpId:VcId Multipl Tx Intvl Rx Intvl
Protocols Type LAG Port LAG ID
Loc Addr
-------------------------------------------------------------------------------
10.20.1.2/32 Up 385488 385352
10.20.1.2 3 1000 1000
srPolicy central N/A N/A
10.20.1.2/32 Down 383831 312114
10.20.1.2 3 1000 1000
srPolicy central N/A N/A
-------------------------------------------------------------------------------
No. of BFD sessions: 1
===============================================================================
# show router bfd seamless-bfd session sr-policy prefix 10.20.1.2/32
===============================================================================
Legend:
Session Id = Interface Name | LSP Name | Prefix | RSVP Sess Name | Service Id
wp = Working path pp = Protecting path
===============================================================================
BFD Session
===============================================================================
Session Id State Tx Pkts Rx Pkts
Rem Addr/Info/SdpId:VcId Multipl Tx Intvl Rx Intvl
Protocols Type LAG Port LAG ID
Loc Addr
-------------------------------------------------------------------------------
10.20.1.2/32 Up 385661 385525
10.20.1.2 3 1000 1000
srPolicy central N/A N/A
10.20.1.2/32 Down 384005 312114
10.20.1.2 3 1000 1000
srPolicy central N/A N/A
-------------------------------------------------------------------------------
No. of BFD sessions: 1
===============================================================================
# show router bfd seamless-bfd session sr-policy prefix 10.20.1.2/32 detail
===============================================================================
BFD Session
===============================================================================
Prefix : 10.20.1.2/32
Local Address : 10.20.1.1
LSP Index : 917507 Path LSP ID : 2
Fec Type : srPolicy Hop Id : 1
Oper State : Up Protocols : srPolicy
Recd Msgs : 4045751 Sent Msgs : 4045751
Up Time : 2d 19:25:46 Up Transitions : 1
Down Time : None Down Transitions : 0
Version Mismatch : 0
Forwarding Information
Local Discr : 1 Local State : Up
Local Diag : 0 (None)
Local Mode : Demand
Local Min Tx : 100 Local Mult : 3
Last Sent : 09/14/2020 14:36:26 Local Min Rx : 100
Type : central
Remote Discr : 524288 Remote State : Up
Remote Diag : 0 (None) Remote Mode : Async
Remote Min Tx : 100 Remote Mult : 3
Remote C-flag : 0
Last Recv : 09/14/2020 14:36:26 Remote Min Rx : 3
===============================================================================
# show router bfd seamless-bfd session sr-policy detail
===============================================================================
BFD Session
===============================================================================
Prefix : 10.20.1.2/32
Local Address : 10.20.1.1
LSP Index : 917514 Path LSP ID : 6
Fec Type : srPolicy Hop Id : 1
Oper State : Up Protocols : srPolicy
Recd Msgs : 385423 Sent Msgs : 385559
Up Time : 3d 19:13:17 Up Transitions : 2
Down Time : None Down Transitions : 1
Version Mismatch : 0
Forwarding Information
Local Discr : 23 Local State : Up
Local Diag : 0 (None)
Local Mode : Demand
Local Min Tx : 1000 Local Mult : 3
Last Sent : 07/06/2020 18:23:46 Local Min Rx : 1000
Type : central
Remote Discr : 524288 Remote State : Up
Remote Diag : 0 (None) Remote Mode : Async
Remote Min Tx : 1000 Remote Mult : 3
Remote C-flag : 0
Last Recv : 07/06/2020 18:23:46 Remote Min Rx : 3
===============================================================================
Prefix : 10.20.1.2/32
Local Address : 10.20.1.1
LSP Index : 917514 Path LSP ID : 9
Fec Type : srPolicy Hop Id : 1
Oper State : Down Protocols : srPolicy
Recd Msgs : 312114 Sent Msgs : 383902
Up Time : None Up Transitions : 5
Down Time : 0d 00:12:26 Down Transitions : 5
Version Mismatch : 0
Forwarding Information
Local Discr : 26 Local State : Down
Local Diag : 1 (Detect time expired)
Local Mode : Demand
Local Min Tx : 1000 Local Mult : 3
Last Sent : 07/06/2020 18:23:45 Local Min Rx : 1000
Type : central
Remote : Unheard
===============================================================================
Label |
Description |
---|---|
Session Id |
Specifies the session ID |
State |
Specifies the session state (Up/Down) |
Tx Pkts |
Specifies the number of packets transmitted |
Rx Pkts |
Specifies the number of packets received |
Rem Addr/Info/SdpId:VcId |
Specifies the session remote endpoint address information |
Multipl |
Specifies the multiplier |
Tx Intvl |
Specifies the transmit interval |
Rx Intvl |
Specifies the receive interval |
Protocols |
Specifies the protocol that the session is bound to |
Type |
Specifies the BFD type cpm-np — Specifies to use CPM network processor |
LAG Port |
Specifies the LAG Port |
LAG ID |
Specifies the LAG ID |
No. of BFD sessions |
Specifies the number of BFD sessions |
Prefix |
Specifies the prefix |
Local Address |
Specifies the local address |
LSP Name |
Specifies the LSP name |
LSP Index |
Specifies the LSP index |
Path LSP ID |
Specifies the path LSP ID |
Fec Type |
Specifies the FEC type |
Return Path |
Specifies the return path label for the S-BFD packet |
Oper State |
Specifies the operational state (Up/Down) |
Protocols |
Specifies the protocol used |
Up Time |
Specifies the up time |
Up Transitions |
Specifies the number of up transitions |
Down Time |
Specifies the down time |
Down Transitions |
Specifies the number of down transitions |
Version Mismatch |
Specifies the number of version mismatches |
Local Discr |
Specifies the local Discr information |
Local State |
Specifies the local state (Up/Down) |
Local Diag |
Specifies the local diag information |
Local Mode |
Specifies the local mode |
Local Min Tx |
Specifies the local Min Tx value |
Local Mult |
Specifies the local Mult value |
Last Sent (ms) |
Specifies the last sent forwarding information |
Local Min Rx |
Specifies the local Min Rx value |
Type |
Specifies the session endpoint type |
Remote Discr |
Specifies the remote Discr value |
Remote State |
Specifies the remote state (Up/Down) |
Remote Diag |
Specifies the remote diagnostic value |
Remote Mode |
Specifies the remote mode |
Remote Min Tx |
Specifies the remote minimum transmit value |
Remote Mult |
Specifies the remote multiplier |
Remote C-flag |
Specifies the remote C-flag value |
Last Recv (ms) |
Specifies the last received value |
Remote Min Rx |
Specifies the remote minimum receive value |
session
Syntax
session detail
session detail lsp-rsvp {head | tail}
session {ipv4 | ipv6} detail [lag lag-id] lag-port port-id
session [detail] lsp-ldp head
session [src ] [detail] lsp-ldp head prefix ip-prefix/prefix-length
session [detail] lsp-ldp tail
session [dest {ip-address | link-local-address}] [detail] lsp-ldp tail ip-address/link-local-addressprefix ip-prefix/prefix-length
session lsp-name lsp-name
session lsp-rsvp {head | tail}
session src ip-address/link-local-address dest {ip-address | link-local-address} [detail] lsp-rsvp {head | tail} tunnel-id tunnel-id lsp-id lsp-id
session mpls-tp
session lsp-name lsp-name [link-type {cc-only | cc-cv}] detail
session p2mp-interface interface-name detail
session src ip-address/link-local-address detail lsp-rsvp {head | tail} rsvp-session-name rsvp-session-name
session [src ip-address/link-local-address] [{ ipv4 | ipv6}]
session src ip-address/link-local-address dest {ip-address | link-local-address}
session src ip-address/link-local-address detail
session summary
session type type [{ipv4 | ipv6}]
Context
[Tree] (show>router>bfd session)
Full Context
show router bfd session
Description
This command displays information for existing BFD sessions.
Parameters
- detail
-
Displays detailed session information.
- lsp-rsvp
-
Displays BFD sessions on an RSVP LSPs.
- head
-
Optional keyword to limit the output to BFD sessions at the head end of LSPs.
- tail
-
Optional keyword to limit the output to BFD sessions at the tail end of LSPs.
- ipv4
-
Optional keyword to limit the output to IPv4-based BFD sessions.
- ipv6
-
Optional keyword to limit the output to IPv6-based BFD sessions.
- lag-id
-
Limits the output to micro-BFD sessions associated with the specified LAG ID.
- port-id
-
Limits the output to micro-BFD sessions associated with the specified port ID.
- lsp-ldp
-
Displays BFD sessions on an LDP LSPs.
- ip-address
-
Limits the output to BFD sessions with the specified IPv4 or IPv6 addresses.
- link-local-address
-
Limits the output to BFD sessions with the specified IPv6 link-local addresses.
- ip-prefix/prefix-length
-
Displays IPv4 or IPv6 addresses of the BFD sessions.
- lsp-name
-
Limits the output to BFD sessions associated with the specified LSP.
- tunnel-id
-
Limits the output to BFD sessions associated with the specified tunnel ID.
- lsp-id
-
Limits the output to BFD sessions associated with the specified LSP ID.
- mpls-tp
-
Optional keyword to limit the output to BFD sessions on MPLS-TP LSPs.
- cc-only
-
Optional keyword to limit the output to CC BFD sessions on MPLS-TP LSPs.
- cc-cv
-
Optional keyword to limit the output to CV BFD sessions on MPLS-TP LSPs.
- interface-name
-
Limits the output to the BFD session for the specified interface.
- rsvp-session-name
-
Limits the output to the BFD session for the specified RSVP session.
- summary
-
Displays summary session information for the router.
- type
-
Limits the output to BFD sessions associated with the specified type.
Platforms
All
Output
The following output is an example of BFD session information, and BFD Session Field Descriptions describes the fields.
Output ExampleA:node-2# show router bfd session
===============================================================================
Legend:
Session Id = Interface Name | LSP Name | Prefix | RSVP Sess Name | Service Id
wp = Working path pp = Protecting path
===============================================================================
BFD Session
===============================================================================
Session Id State Tx Pkts Rx Pkts
Rem Addr/Info/SdpId:VcId Multipl Tx Intvl Rx Intvl
Protocols Type LAG Port LAG ID
Loc Addr
-------------------------------------------------------------------------------
10.20.1.6/32 Up N/A N/A
10.20.1.6 3 1000 1000
mplsLsp cpm-np N/A N/A
10.20.1.3
-------------------------------------------------------------------------------
No. of BFD sessions: 1
===============================================================================
A:node-2# show router bfd session
===============================================================================
Legend:
Session Id = Interface Name | LSP Name | Prefix | RSVP Sess Name | Service Id
wp = Working path pp = Protecting path
===============================================================================
BFD Session
===============================================================================
Session Id State Tx Pkts Rx Pkts
Rem Addr/Info/SdpId:VcId Multipl Tx Intvl Rx Intvl
Protocols Type LAG Port LAG ID
-------------------------------------------------------------------------------
10.20.1.6/32 Up N/A N/A
10.20.1.6 3 10 10
mplsLsp cpm-np N/A N/A
10.20.1.6/32 Up N/A N/A
10.20.1.6 3 10 10
mplsLsp cpm-np N/A N/A
10.20.1.6/32 Up N/A N/A
10.20.1.6 3 10 10
mplsLsp cpm-np N/A N/A
-------------------------------------------------------------------------------
No. of BFD sessions: 3
===============================================================================
A:node-2# show router bfd session summary
=============================
BFD Session Summary
=============================
Termination Session Count
-----------------------------
central 0
cpm-np 3
iom, slot 1 0
iom, slot 2 0
iom, slot 3 0
iom, slot 4 0
iom, slot 5 0
iom, slot 6 0
Total 3
=============================
A:node-2# show router bfd session type cpm-np
===============================================================================
Legend:
Session Id = Interface Name | LSP Name | Prefix | RSVP Sess Name | Service Id
wp = Working path pp = Protecting path
===============================================================================
BFD Session
===============================================================================
Session Id State Tx Pkts Rx Pkts
Rem Addr/Info/SdpId:VcId Multipl Tx Intvl Rx Intvl
Protocols Type LAG Port LAG ID
-------------------------------------------------------------------------------
10.20.1.6/32 Up N/A N/A
10.20.1.6 3 10 10
mplsLsp cpm-np N/A N/A
10.20.1.6/32 Up N/A N/A
10.20.1.6 3 10 10
mplsLsp cpm-np N/A N/A
10.20.1.6/32 Up N/A N/A
10.20.1.6 3 10 10
mplsLsp cpm-np N/A N/A
-------------------------------------------------------------------------------
No. of BFD sessions: 3
===============================================================================
A:node-2# show router bfd seamless-bfd session lsp-path detail
===============================================================================
BFD Session
===============================================================================
Prefix : 10.20.1.6/32
Local Address : 10.20.1.3
LSP Name : C_F_70001
LSP Index : 70001 Path LSP ID : 62464
Fec Type : srTe
Oper State : Up Protocols : mplsLsp
Up Time : 0d 15:10:06 Up Transitions : 1
Down Time : None Down Transitions : 0
Version Mismatch : 0
Forwarding Information
Local Discr : 42 Local State : Up
Local Diag : 0 (None)
Local Mode : Demand
Local Min Tx : 10 Local Mult : 3
Last Sent (ms) : 0 Local Min Rx : 10
Type : cpm-np
Remote Discr : 524293 Remote State : Up
Remote Diag : 0 (None) Remote Mode : Async
Remote Min Tx : 10 Remote Mult : 3
Last Recv (ms) : 0 Remote Min Rx : 3
===============================================================================
Prefix : 10.20.1.6/32
Local Address : 10.20.1.3
LSP Name : C_F_70001
LSP Index : 70001 Path LSP ID : 62466
Fec Type : srTe
Oper State : Up Protocols : mplsLsp
Up Time : 0d 15:10:06 Up Transitions : 1
Down Time : None Down Transitions : 0
Version Mismatch : 0
Forwarding Information
Local Discr : 43 Local State : Up
Local Diag : 0 (None)
Local Mode : Demand
Local Min Tx : 10 Local Mult : 3
Last Sent (ms) : 0 Local Min Rx : 10
Type : cpm-np
Remote Discr : 524293 Remote State : Up
Remote Diag : 0 (None) Remote Mode : Async
Remote Min Tx : 10 Remote Mult : 3
Last Recv (ms) : 0 Remote Min Rx : 3
===============================================================================
Prefix : 10.20.1.6/32
Local Address : 10.20.1.3
LSP Name : C_F_70001
LSP Index : 70001 Path LSP ID : 62468
Fec Type : srTe
Oper State : Up Protocols : mplsLsp
Up Time : 0d 15:09:26 Up Transitions : 1
Down Time : None Down Transitions : 0
Version Mismatch : 0
Forwarding Information
Local Discr : 44 Local State : Up
Local Diag : 0 (None)
Local Mode : Demand
Local Min Tx : 10 Local Mult : 3
Last Sent (ms) : 0 Local Min Rx : 10
Type : cpm-np
Remote Discr : 524293 Remote State : Up
Remote Diag : 0 (None) Remote Mode : Async
Remote Min Tx : 10 Remote Mult : 3
Last Recv (ms) : 0 Remote Min Rx : 3
===============================================================================
===============================================================================
A:node-2# show router bfd session src 3ffe::a01:102 dest 3ffe::a01:103
===============================================================================
BFD Session
===============================================================================
Remote Address : 3ffe::a01:103
Admin State : Up Oper State : Up (3)
Protocols : static bgp
Rx Interval : 10 Tx Interval : 10
Multiplier : 3 Echo Interval : 0
Up Time : 0d 07:24:54 Up Transitions : 1
Down Time : None Down Transitions : 0
Version Mismatch : 0
Forwarding Information
Local Discr : 2051 Local State : Up (3)
Local Diag : 0 (None) Local Mode : Async
Local Min Tx : 10 Local Mult : 3
Last Sent (ms) : 5 Local Min Rx : 10
Type : cpm-np
Remote Discr : 1885 Remote State : Up (3)
Remote Diag : 0 (None) Remote Mode : Async
Remote Min Tx : 10 Remote Mult : 3
Last Recv (ms) : 1 Remote Min Rx : 10
===============================================================================
A:node-2# show router bfd session src fe80::a0a:a02-port-1-10 dest fe80::a0a:a03-
port-1-10
===============================================================================
BFD Session
===============================================================================
Remote Address : 2001:db8::a0a:a03
Admin State : Up Oper State : Up (3)
Protocols : pim isis ospf3
Rx Interval : 10 Tx Interval : 10
Multiplier : 3 Echo Interval : 0
Up Time : 0d 07:10:20 Up Transitions : 3
Down Time : None Down Transitions : 2
Version Mismatch : 0
Forwarding Information
Local Discr : 42 Local State : Up (3)
Local Diag : 3 (Neighbor signalled s* Local Mode : Async
Local Min Tx : 10 Local Mult : 3
Last Sent (ms) : 6 Local Min Rx : 10
Type : cpm-np
Remote Discr : 270 Remote State : Up (3)
Remote Diag : 0 (None) Remote Mode : Async
Remote Min Tx : 10 Remote Mult : 3
Last Recv (ms) : 8 Remote Min Rx : 10
===============================================================================
* indicates that the corresponding row element may have been truncated.
A:node-2# show router bfd session ipv4
===============================================================================
BFD Session
===============================================================================
Interface State Tx Intvl Rx Intvl Multipl
Remote Address Protocols Tx Pkts Rx Pkts Type
-------------------------------------------------------------------------------
port-1-1 Up (3) 500 500 3
10.1.1.3 pim isis 51532 51279 iom
port-1-2 Up (3) 500 500 3
10.2.1.3 pim isis 51529 51279 iom
port-1-3 Up (3) 500 500 3
10.3.1.3 pim isis 51529 51279 iom
port-1-4 Up (3) 500 500 3
10.4.1.3 pim isis 51529 51279 iom
port-1-5 Up (3) 500 500 3
10.5.1.3 pim isis 51529 51279 iom
port-1-6 Up (3) 500 500 3
10.6.1.3 pim isis 51529 51279 iom
...
===============================================================================
A:node-2# show router bfd session ipv6
===============================================================================
BFD Session
===============================================================================
Interface State Tx Intvl Rx Intvl Multipl
Remote Address Protocols Tx Pkts Rx Pkts Type
-------------------------------------------------------------------------------
port-1-1 Up (3) 10 10 3
3ffe::a01:103 static bgp N/A N/A cpm-np
port-1-1 Up (3) 10 10 3
fe80::a0a:a03 pim isis ospf3 N/A N/A cpm-np
port-1-2 Up (3) 10 10 3
3ffe::a02:103 static bgp N/A N/A cpm-np
port-1-2 Up (3) 10 10 3
fe80::a0a:a03 pim isis ospf3 N/A N/A cpm-np
port-1-3 Up (3) 10 10 3
3ffe::a03:103 static bgp N/A N/A cpm-np
port-1-3 Up (3) 10 10 3
fe80::a0a:a03 pim isis ospf3 N/A N/A cpm-np
port-1-4 Up (3) 10 10 3
3ffe::a04:103 static bgp N/A N/A cpm-np
port-1-4 Up (3) 10 10 3
...
===============================================================================
A:node-2# show router bfd session detail lsp-
rsvp head src 10.20.1.2 dest 10.20.1.5 tunnel-id 1 lsp-id 31744
===============================================================================
BFD On LSP Session
===============================================================================
Rsvp Session Name : lsp1::path1
Remote Address : 10.20.1.5
Lsp Id : 31744 Tunnel Id : 1
Oper State : Up Protocols : lsp
Recd Msgs : 240 Sent Msgs : 240
Up Time : 0d 00:03:58 Up Transitions : 1
Down Time : None Down Transitions : 0
Version Mismatch : 0
Forwarding Information
Local Discr : 1 Local State : Up
Local Diag : 0 (None)
Local Mode : Async
Local Min Tx : 1000 Local Mult : 3
Last Sent : 07/28/2015 19:05:13 Local Min Rx : 1000
Type : central
Remote Discr : 1 Remote State : Up
Remote Diag : 0 (None) Remote Mode : Async
Remote Min Tx : 1000 Remote Mult : 3
Last Recv : 07/28/2015 19:05:13 Remote Min Rx : 1000
===============================================================================
===============================================================================
A:node-2# show router bfd session
===============================================================================
Legend:
Session Id = Interface Name | LSP Name | Prefix | RSVP Sess Name | Service Id
wp = Working path pp = Protecting path
===============================================================================
BFD Session
===============================================================================
Session Id State Tx Pkts Rx Pkts
Rem Addr/Info/SdpId:VcId Multipl Tx Intvl Rx Intvl
Protocols Type LAG Port LAG ID
-------------------------------------------------------------------------------
2001:db8:696a:6b6c:6d6e:6f70:7172:7374/128 Down 4111222334 3111222334 <<<
LMB: stub values
N/A 19 1000 2000
bgp central N/A N/A
103.104.105.106/32 Init N/A N/A
102.103.104.105 19 1000 2000
rsvp mcIpsec bgpLsp cpm-np N/A N/A
RSVP_session_name_20__24__28__32 Up 4111222336 3111222336
2001:db8:6b6c:6d6e:6f70:7172:7374:7576 19 1000 2000
mc-ring ospf3 ldpLsp iom N/A N/A
-------------------------------------------------------------------------------
No. of BFD sessions: 3
===============================================================================
The following output is an example of BFD information.
A:node-2# show router 3 bfd session
===============================================================================
BFD Session
===============================================================================
InterfaceState Tx Intvl Rx Intvl Multipl
Remote Address Protocols Tx Pkts Rx Pkts Type
-------------------------------------------------------------------------------
ies-3-10.1.3.3 Up (3) 10 10 3
10.1.3.2 ospf2 N/A N/A cpm-np
ies-3-10.1.4.3 Up (3) 100 100 3
10.1.4.2 pim 455 464 iom
-------------------------------------------------------------------------------
No. of BFD sessions: 2
===============================================================================
A:node-2# show router bfd session src 10.120.1.4 dest 10.120.1.3
===============================================================================
BFD Session
===============================================================================
Remote Address : 10.120.1.3
Admin State : Up Oper State : Up (3)
Protocols : static
Rx Interval : 10 Tx Interval : 10
Multiplier : 3 Echo Interval : 0
Up Time : 1d 19:03:28 Up Transitions : 2
Down Time : None Down Transitions : 1
Version Mismatch : 0
Forwarding Information
Local Discr : 19269 Local State : Up (3)
Local Diag : 0 (None) Local Mode : Async
Local Min Tx : 10 Local Mult : 3
Last Sent (ms) : 6 Local Min Rx : 10
Type : cpm-np
Remote Discr : 5101 Remote State : Up (3)
Remote Diag : 0 (None) Remote Mode : Async
Remote Min Tx : 1000 Remote Mult : 3
Last Recv (ms) : 367 Remote Min Rx : 10
===============================================================================
A:node-2# show router bfd session
===============================================================================
BFD Session
===============================================================================
Interface/Lsp Name State Tx Intvl Rx Intvl Multipl
Remote Address/Info Protocols Tx Pkts Rx Pkts Type
-------------------------------------------------------------------------------
wp::lsp-32 Down (1) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
wp::lsp-33 Down (1) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
wp::lsp-34 Down (1) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
wp::lsp-35 Down (1) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
wp::lsp-36 Down (1) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
wp::lsp-37 Down (1) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
wp::lsp-38 Down (1) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
wp::lsp-39 Down (1) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
wp::lsp-40 Down (1) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
wp::lsp-41 Down (1) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
pp::lsp-32 Up (3) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
pp::lsp-33 Up (3) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
pp::lsp-34 Up (3) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
pp::lsp-35 Up (3) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
pp::lsp-36 Up (3) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
pp::lsp-37 Up (3) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
pp::lsp-38 Up (3) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
pp::lsp-39 Up (3) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
pp::lsp-40 Up (3) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
pp::lsp-41 Up (3) 1000 1000 3
0::0.0.0.0 mplsTp N/A N/A cpm-np
-------------------------------------------------------------------------------
No. of BFD sessions: 20
-------------------------------------------------------------------------------
wp = Working path pp = Protecting path
===============================================================================
Label |
Description |
---|---|
State |
Displays the administrative state for this BFD session |
Protocol |
Displays the active protocol |
Tx Intvl |
Displays the interval, in milliseconds, between the transmitted BFD messages to maintain the session |
Tx Pkts |
Displays the number of transmitted BFD packets |
Rx Intvl |
Displays the expected interval, in milliseconds, between the received BFD messages to maintain the session |
Rx Pkts |
Displays the number of received packets |
Mult |
Displays the integer used by BFD to declare when the neighbor is down |
session
Syntax
session [session-type] [from ip-address [ to ip-address] [lsp-name session-name] [status {up | down}] [ detail] [interface ip-int-name]
Context
[Tree] (show>router>rsvp session)
Full Context
show router rsvp session
Description
This command shows RSVP session information.
Parameters
- session-type
-
Specifies the session type.
- from ip-address
-
Specifies the IP address of the originating router.
- to ip-address
-
Specifies the IP address of the egress router.
- session-name
-
Specifies the name, up to 160 characters in length, of the LSP used in the path. "*” can be used as a wildcard character.
- status up
-
Specifies to display a session that is operationally up.
- status down
-
Specifies to display a session that is operationally down.
- detail
-
Displays detailed information.
- ip-int-name
-
Specifies the name of an existing MPLS interface.
If the string contains special characters (#, $, spaces, and so on), the entire string must be enclosed within double quotes.
The interface option filters the display to include all RSVP sessions that use this interface name as "In Interface” or as "Out Interface”.
Platforms
All
Output
The following output is an example of RSVP session information.
RSVP Session Output Fields describes RSVP session output fields.
Label |
Description |
---|---|
From |
The IP address of the originating router. |
To |
The IP address of the egress router. |
Tunnel ID |
The IP address of the tunnel’s ingress node supporting this RSVP session. |
LSP ID |
The ID assigned by the agent to this RSVP session. |
Name |
The administrative name assigned to the RSVP session by the agent. |
State |
Down — The operational state of this RSVP session is down. Up — The operational state of this RSVP session is up. |
*A:SRU4>show>router>rsvp# session
===============================================================================
RSVP Sessions
===============================================================================
From To Tunnel LSP Name State
ID ID
-------------------------------------------------------------------------------
10.30.1.5 10.30.1.4 18 27648 b4-1::b4-1 Up
10.30.1.5 10.30.1.4 1 37902 gsr::gsr Up
10.30.1.5 10.20.1.22 11 53760 to_10_20_1_22_cspf::to_10_2* Up
10.30.1.4 10.20.1.20 146 17920 to_10_20_1_20_cspf_3::to_10* Up
10.30.1.4 10.20.1.20 145 34816 to_10_20_1_20_cspf_2::to_10* Up
10.30.1.4 10.20.1.20 147 45056 to_10_20_1_20_cspf_4::to_10* Up
10.30.1.4 10.20.1.20 148 6656 to_10_20_1_20_cspf_5::to_10* Up
10.30.1.4 10.20.1.20 149 58880 to_10_20_1_20_cspf_6::to_10* Up
10.30.1.4 10.20.1.20 150 13312 to_10_20_1_20_cspf_7::to_10* Up
10.30.1.4 10.20.1.20 152 40448 to_10_20_1_20_cspf_9::to_10* Up
10.30.1.4 10.20.1.20 154 27648 to_10_20_1_20_cspf_11::to_1* Up
10.30.1.4 10.20.1.20 155 12288 to_10_20_1_20_cspf_12::to_1* Up
10.30.1.4 10.20.1.20 151 46080 to_10_20_1_20_cspf_8::to_10* Up
10.30.1.4 10.20.1.20 153 512 to_10_20_1_20_cspf_10::to_1* Up
10.30.1.4 10.20.1.22 164 62464 to_10_20_1_22_cspf_2::to_10* Up
10.30.1.4 10.20.1.20 156 37888 to_10_20_1_20_cspf_13::to_1* Up
10.30.1.4 10.20.1.20 157 24064 to_10_20_1_20_cspf_14::to_1* Up
10.30.1.4 10.20.1.20 158 19968 to_10_20_1_20_cspf_15::to_1* Up
10.30.1.4 10.20.1.20 161 59904 to_10_20_1_20_cspf_18::to_1* Up
...
10.30.1.3 10.30.1.4 54 23088 to_10_30_1_4_cspf_4::to_11* Up
-------------------------------------------------------------------------------
Sessions : 1976
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:SRU4>show>router>rsvp#
A:ALA-12# show router rsvp session lsp-name A_C_2::A_C_2 status up
===============================================================================
RSVP Sessions
===============================================================================
From To Tunnel LSP Name State
ID ID
-------------------------------------------------------------------------------
10.20.1.1 10.20.1.3 2 40 A_C_2::A_C_2 Up
-------------------------------------------------------------------------------
Sessions : 1
===============================================================================
A:ALA-12#
A:Phoenix 199# show router rsvp session detail
===============================================================================
RSVP Sessions (Detailed)
===============================================================================
-------------------------------------------------------------------------------
LSP : From Reno to Atlanta RSVP-TE::primary_empty
-------------------------------------------------------------------------------
From : 192.168.48.194 To : 192.168.48.224
Tunnel ID : 4 LSP ID : 26682
Style : SE State : Up
Session Type : Transit
In Interface : 1/1/1 Out Interface : 1/1/7
In IF Name : toSim194
Out IF Name : toSim184
In Label : 262126 Out Label : 262128
Previous Hop : 10.202.5.194 Next Hop : 10.0.13.184
SetupPriority : 7 Hold Priority : 0
Class Type : 0
SubGrpOrig ID : 0 SubGrpOrig Addr:
P2MP ID : 0
FrrAvailType : Facility
FrrBypassLspName: bypass-link10.0.13.184-61452
FrrSrlgStrict : N/A SrlgDisjoint : N/A
Path Recd : 22859 Path Sent : 22813
Resv Recd : 22891 Resv Sent : 22848
Summary msgs :
SPath Recd : 0 SPath Sent : 0
SResv Recd : 0 SResv Sent : 0
LSP Attr Flags : N/A
-------------------------------------------------------------------------------
LSP : From Reno to Atlanta RSVP-TE::secondary_empty
-------------------------------------------------------------------------------
From : 192.168.48.194 To : 192.168.48.224
Tunnel ID : 4 LSP ID : 26684
Style : SE State : Up
Session Type : Transit
In Interface : 1/1/2 Out Interface : 1/1/7
In IF Name : toSim219
Out IF Name : toSim184
In Label : 262130 Out Label : 262132
Previous Hop : 10.202.1.219 Next Hop : 10.0.13.184
SetupPriority : 7 Hold Priority : 0
Class Type : 0
SubGrpOrig ID : 0 SubGrpOrig Addr:
P2MP ID : 0
FrrAvailType : N/A
FrrSrlgStrict : N/A SrlgDisjoint : N/A
Path Recd : 22762 Path Sent : 24117
Resv Recd : 22870 Resv Sent : 22781
Summary msgs :
SPath Recd : 0 SPath Sent : 0
SResv Recd : 0 SResv Sent : 0
LSP Attr Flags : N/A
-------------------------------------------------------------------------------
LSP : bypass-link10.202.5.199-61877
-------------------------------------------------------------------------------
From : 192.168.48.194 To : 10.202.1.199
Tunnel ID : 61877 LSP ID : 16
Style : FF State : Up
Session Type : Terminate
In Interface : 1/1/2 Out Interface : n/a
In IF Name : toSim219
Out IF Name : n/a
In Label : 262125 Out Label : n/a
Previous Hop : 10.202.1.219 Next Hop : n/a
SetupPriority : 7 Hold Priority : 0
Class Type : 0
SubGrpOrig ID : 0 SubGrpOrig Addr:
P2MP ID : 0
FrrAvailType : N/A
FrrSrlgStrict : N/A SrlgDisjoint : N/A
Path Recd : 22901 Path Sent : 0
Resv Recd : 0 Resv Sent : 22749
Summary msgs :
SPath Recd : 0 SPath Sent : 0
SResv Recd : 0 SResv Sent : 0
LSP Attr Flags : N/A
-------------------------------------------------------------------------------
LSP : bypass-link10.0.13.184-61452
-------------------------------------------------------------------------------
From : 192.168.48.199 To : 10.0.3.184
Tunnel ID : 61452 LSP ID : 24
Style : FF State : Up
Session Type : Bypass Tunnel
In Interface : n/a Out Interface : 1/1/3
In IF Name : n/a
Out IF Name : toSim185
In Label : n/a Out Label : 262126
Previous Hop : n/a Next Hop : 10.0.5.185
SetupPriority : 7 Hold Priority : 0
Class Type : 0
SubGrpOrig ID : 0 SubGrpOrig Addr:
P2MP ID : 0
FrrAvailType : N/A
FrrSrlgStrict : N/A SrlgDisjoint : N/A
Path Recd : 0 Path Sent : 23423
Resv Recd : 22912 Resv Sent : 0
Summary msgs :
SPath Recd : 0 SPath Sent : 0
SResv Recd : 0 SResv Sent : 0
LSP Attr Flags : N/A
===============================================================================
A:Phoenix 199#
A:Phoenix 199# show router rsvp session interface toSim219 detail
===============================================================================
RSVP Sessions (Detailed)
===============================================================================
-------------------------------------------------------------------------------
LSP : From Reno to Atlanta RSVP-TE::secondary_empty
-------------------------------------------------------------------------------
From : 192.168.48.194 To : 192.168.48.224
Tunnel ID : 4 LSP ID : 26684
Style : SE State : Up
Session Type : Transit
In Interface : 1/1/2 Out Interface : 1/1/7
In IF Name : toSim219
Out IF Name : toSim184
In Label : 262130 Out Label : 262132
Previous Hop : 10.202.1.219 Next Hop : 10.0.13.184
SetupPriority : 7 Hold Priority : 0
Class Type : 0
SubGrpOrig ID : 0 SubGrpOrig Addr:
P2MP ID : 0
FrrAvailType : N/A
FrrSrlgStrict : N/A SrlgDisjoint : N/A
Path Recd : 22768 Path Sent : 24124
Resv Recd : 22876 Resv Sent : 22789
Summary msgs :
SPath Recd : 0 SPath Sent : 0
SResv Recd : 0 SResv Sent : 0
LSP Attr Flags : N/A
-------------------------------------------------------------------------------
LSP : bypass-link10.202.5.199-61877
-------------------------------------------------------------------------------
From : 192.168.48.194 To : 10.202.1.199
Tunnel ID : 61877 LSP ID : 16
Style : FF State : Up
Session Type : Terminate
In Interface : 1/1/2 Out Interface : n/a
In IF Name : toSim219
Out IF Name : n/a
In Label : 262125 Out Label : n/a
Previous Hop : 10.202.1.219 Next Hop : n/a
SetupPriority : 7 Hold Priority : 0
Class Type : 0
SubGrpOrig ID : 0 SubGrpOrig Addr:
P2MP ID : 0
FrrAvailType : N/A
FrrSrlgStrict : N/A SrlgDisjoint : N/A
Path Recd : 22906 Path Sent : 0
Resv Recd : 0 Resv Sent : 22756
Summary msgs :
SPath Recd : 0 SPath Sent : 0
SResv Recd : 0 SResv Sent : 0
LSP Attr Flags : N/A
===============================================================================
*A:Dut-C# show router mpls lsp transit detail
==============================================================================
MPLS LSPs (Transit) (Detail)
------------------------------------------------------------------------------
LSP tof1::sec2
------------------------------------------------------------------------------
From : 10.20.1.2 To : 10.20.1.4
State : Up
SetupPriority : 5 Hold Priority : 5
Class Type : 5
In Interface : lag-1:0 In Label : 131068
Out Interface : 2/1/2 Out Label : 131068
Previous Hop : 10.10.12.2 Next Hop : 10.10.11.4
Reserved BW : 1000 Kbps
==============================================================================
*A:Dut-C#
*A:Dut-B# show router rsvp session detour-terminate detail
==============================================================================
RSVP Sessions (Detailed)
==============================================================================
LSP : tof878::1_detour
------------------------------------------------------------------------------
From : 10.20.1.2 To : 10.20.1.4
Tunnel ID : 878 LSP ID : 14929
Style : SE State : Up
Session Type : Terminate (Detour)
In Interface : lag-1:0 Out Interface : 1/1/2:8
In Label : 131069 Out Label : 127951
Previous Hop : 10.10.12.3 Next Hop : 10.10.108.4
SetupPriority : 4 Hold Priority : 4
Class Type : 5
SugGrpOrig ID : 0 SubGrpOrig Addr: 0.0.0.0
P2MP ID : 0
Path Recd : 128 Path Sent : 0
Resv Recd : 125 Resv Sent : 124
Summary messages:
SPath Recd : 0 SPath Sent : 0
SResv Recd : 0 SResv Sent : 0
==============================================================================
*A:Dut-B#
*A:Dut-B# show router rsvp session bypass-tunnel detail
==============================================================================
RSVP Sessions (Detailed)
==============================================================================
LSP : bypass-link10.10.108.4
------------------------------------------------------------------------------
From : 10.20.1.2 To : 10.10.109.4
Tunnel ID : 4003 LSP ID : 6
Style : FF State : Up
Session Type : Bypass Tunnel
In Interface : n/a Out Interface : 1/1/2:9
In Label : n/a Out Label : 124069
Previous Hop : n/a Next Hop : 10.10.109.4
SetupPriority : 7 Hold Priority : 0
Class Type : 0
SugGrpOrig ID : 0 SubGrpOrig Addr: 0.0.0.0
P2MP ID : 0
Path Recd : 0 Path Sent : 3
Resv Recd : 4 Resv Sent : 0
Summary messages:
SPath Recd : 0 SPath Sent : 0
SResv Recd : 0 SResv Sent : 0
==============================================================================
*A:Dut-B#
*A:Dut-B# show router rsvp session detour detail
==============================================================================
RSVP Sessions (Detailed)
------------------------------------------------------------------------------
LSP : tof919::1_detour
------------------------------------------------------------------------------
From : 10.20.1.2 To : 10.20.1.4
Tunnel ID : 919 LSP ID : 15441
Style : SE State : Up
Session Type : Originate (Detour)
In Interface : n/a Out Interface : 1/1/2:1
In Label : n/a Out Label : 129865
Previous Hop : n/a Next Hop : 10.10.101.4
SetupPriority : 4 Hold Priority : 4
Class Type : 5
SugGrpOrig ID : 0 SubGrpOrig Addr: 0.0.0.0
P2MP ID : 0
Path Recd : 0 Path Sent : 106
Resv Recd : 113 Resv Sent : 0
Summary messages:
SPath Recd : 0 SPath Sent : 0
SResv Recd : 0 SResv Sent : 0
==============================================================================
*A:Dut-B#
*A:Dut-B# show router rsvp session detour-transit detail
==============================================================================
RSVP Sessions (Detailed)
------------------------------------------------------------------------------
LSP : tof919::1_detour
------------------------------------------------------------------------------
From : 10.20.1.2 To : 10.20.1.4
Tunnel ID : 919 LSP ID : 15441
Style : SE State : Up
Session Type : Transit (Detour)
In Interface : lag-1:0 Out Interface : 1/1/2:6
In Label : 131071 Out Label : 127952
Previous Hop : 10.10.12.3 Next Hop : 10.10.106.4
SetupPriority : 4 Hold Priority : 4
Class Type : 5
SugGrpOrig ID : 0 SubGrpOrig Addr: 0.0.0.0
P2MP ID : 0
Path Recd : 119 Path Sent : 123
Resv Recd : 121 Resv Sent : 120
Summary messages:
SPath Recd : 0 SPath Sent : 0
SResv Recd : 0 SResv Sent : 0
==============================================================================
*A:Dut-B#
*A:Dut-B# show router rsvp session detour-terminate detail
==============================================================================
RSVP Sessions (Detailed)
------------------------------------------------------------------------------
LSP : tof878::1_detour
------------------------------------------------------------------------------
From : 10.20.1.2 To : 10.20.1.4
Tunnel ID : 878 LSP ID : 14929
Style : SE State : Up
Session Type : Terminate (Detour)
In Interface : lag-1:0 Out Interface : 1/1/2:8
In Label : 131069 Out Label : 127951
Previous Hop : 10.10.12.3 Next Hop : 10.10.108.4
SetupPriority : 4 Hold Priority : 4
Class Type : 5
SugGrpOrig ID : 0 SubGrpOrig Addr: 0.0.0.0
P2MP ID : 0
Path Recd : 128 Path Sent : 0
Resv Recd : 125 Resv Sent : 124
Summary messages:
SPath Recd : 0 SPath Sent : 0
SResv Recd : 0 SResv Sent : 0
==============================================================================
*A:Dut-B#
*A:Dut-B# show router rsvp session bypass-tunnel detail
==============================================================================
RSVP Sessions (Detailed)
------------------------------------------------------------------------------
LSP : bypass-link10.10.108.4
------------------------------------------------------------------------------
From : 10.20.1.2 To : 10.10.109.4
Tunnel ID : 4003 LSP ID : 6
Style : FF State : Up
Session Type : Bypass Tunnel
In Interface : n/a Out Interface : 1/1/2:9
In Label : n/a Out Label : 124069
Previous Hop : n/a Next Hop : 10.10.109.4
SetupPriority : 7 Hold Priority : 0
Class Type : 0
SugGrpOrig ID : 0 SubGrpOrig Addr: 0.0.0.0
P2MP ID : 0
Path Recd : 0 Path Sent : 3
Resv Recd : 4 Resv Sent : 0
Summary messages:
SPath Recd : 0 SPath Sent : 0
SResv Recd : 0 SResv Sent : 0
==============================================================================
*A:Dut-B#
session
Syntax
session src-ip ip-address dst-ip ip-address
Context
[Tree] (clear>router>bfd session)
Full Context
clear router bfd session
Description
This command clears BFD sessions.
Parameters
- src-ip ip-address
-
Specifies the address of the local endpoint of this BFD session.
- dst-ip ip-address
-
Specifies the address of the remote endpoint of this BFD session.
Platforms
All
session
Syntax
session all
session client srcAddr
Context
[Tree] (clear>video>id session)
Full Context
clear video id session
Description
This command clears session information.
Parameters
- all
-
Clears all sessions.
- client srcAddr
-
Clears information for the client source address.
Platforms
7450 ESS, 7750 SR, 7750 SR-1s, 7750 SR-2s, 7750 SR-7s, 7750 SR-14s
session
Syntax
session all [rt-server] [fcc-server]
session client srcAddr [rt-server] [ fcc-server]
Context
[Tree] (clear>video>statistics>id session)
Full Context
clear video statistics id session
Description
This command clears video statistics for a particular channel.
Parameters
- all
-
Clears statistics for all sessions.
- rt-server
-
Clears all RET server related statistics.
- fcc-server
-
Clears all FCC server related statistics.
- client srcAddr
-
Clears statistics for the specified source address.
Platforms
7450 ESS, 7750 SR, 7750 SR-1s, 7750 SR-2s, 7750 SR-7s, 7750 SR-14s
session
Syntax
session session-name [{all | base | bin-group | event-mon | meas-interval}]
Context
[Tree] (show>oam-pm session)
Full Context
show oam-pm session
Description
Show the configuration and status information for an OAM Performance Monitoring session.
Parameters
- session-name
-
Specifies the session name up to 32 characters.
- all
-
Displays all attributes.
- base
-
Specifies the base configuration option for the session.
- bin-group
-
Specifies the associated bin group and its attributes.
- event-mon
-
Configures event monitoring and last TCA.
- meas-interval
-
Configures event monitoring and last TCA.
Platforms
All
Output
The following output is an example of OAM-PM configuration information.
Output Exampleshow oam-pm session "vpls1000-PM-YL4-1/1/9:1000.1000" all
-------------------------------------------------------------------------------
Basic Session Configuration
-------------------------------------------------------------------------------
Session Name : vpls1000-PM-YL4-1/1/9:1000.1000
Description : (Not Specified)
Test Family : ethernet Session Type : proactive
Bin Group : 3
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Ethernet Configuration
-------------------------------------------------------------------------------
Source MEP : 30 Priority : 7 (FC : nc)
Source Domain : 14 Dest MAC Address : 00:00:00:00:00:32
Source Assoc'n : 1000 Remote MEP : none
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
DMM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID : 10001 Admin State : Up
Oper State : Up Data TLV Size : 0 octets
On-Demand Duration: Not Applicable On-Demand Remaining: Not Applicable
Interval : 1000 ms
Detectable Tx Err : none
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SLM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID : 10001 Admin State : Up
Oper State : Up Data TLV Size : 0 octets
On-Demand Duration: Not Applicable On-Demand Remaining: Not Applicable
Interval : 100 ms
CHLI Threshold : 4 HLIs Frames Per Delta-T : 10 SLM frames
Consec Delta-Ts : 10 FLR Threshold : 50%
HLI Force Count : no
Detectable Tx Err : none
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
5-mins Measurement Interval Configuration
-------------------------------------------------------------------------------
Duration : 5-mins Intervals Stored : 32
Boundary Type : clock-aligned Clock Offset : 0 seconds
Accounting Policy : none Event Monitoring : enabled
Delay Event Mon : enabled Loss Event Mon : enabled
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Configured Lower Bounds for Delay Tests, in microseconds
-------------------------------------------------------------------------------
Group Description Admin Bin FD(us) FDR(us) IFDV(us)
-------------------------------------------------------------------------------
3 Up 0 0 0 0
1 1 500 250
2 500 1000 500
3 1000 1500 1000
4 2000 2000 1500
5 3000 2500 2000
6 4000 3000 2500
7 5000 3500 3000
8 5500 4000 3500
9 6500 4500 4000
-------------------------------------------------------------------------------
---------------------------------------
Bins Excluded from Average
---------------------------------------
Bin Type Direction Bins
---------------------------------------
FD round-trip 0,9
---------------------------------------
--------------------------------------------------------------------
Bins Excluded from Delay Event Count
--------------------------------------------------------------------
Bin Type Direction Lowest Excluded Bin Lower Bound (us)
--------------------------------------------------------------------
FD round-trip 9 6500
--------------------------------------------------------------------
-------------------------------------------------------------------------------
Delay Events for the DMM Test
-------------------------------------------------------------------------------
Bin Type Direction LowerBound(us) Raise Clear Last TCA (UTC)
-------------------------------------------------------------------------------
FD round-trip 2000 50 10 2017/01/04 16:55:00
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Loss Events for the SLM Test
-------------------------------------------------------------------------------
Event Type Direction Raise Clear Last TCA (UTC)
-------------------------------------------------------------------------------
HLI aggregate 50 0 none
-------------------------------------------------------------------------------
show oam-pm session "vpls1000-PM-YL4-1/1/9:1000.1000" base
-------------------------------------------------------------------------------
Basic Session Configuration
-------------------------------------------------------------------------------
Session Name : vpls1000-PM-YL4-1/1/9:1000.1000
Description : (Not Specified)
Test Family : ethernet Session Type : proactive
Bin Group : 3
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Ethernet Configuration
-------------------------------------------------------------------------------
Source MEP : 30 Priority : 7 (FC : nc)
Source Domain : 14 Dest MAC Address : 00:00:00:00:00:32
Source Assoc'n : 1000 Remote MEP : none
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
DMM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID : 10001 Admin State : Up
Oper State : Up Data TLV Size : 0 octets
On-Demand Duration: Not Applicable On-Demand Remaining: Not Applicable
Interval : 1000 ms
Detectable Tx Err : none
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SLM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID : 10001 Admin State : Up
Oper State : Up Data TLV Size : 0 octets
On-Demand Duration: Not Applicable On-Demand Remaining: Not Applicable
Interval : 100 ms
CHLI Threshold : 4 HLIs Frames Per Delta-T : 10 SLM frames
Consec Delta-Ts : 10 FLR Threshold : 50%
HLI Force Count : no
Detectable Tx Err : none
-------------------------------------------------------------------------------
show oam-pm session "vpls1000-PM-YL4-1/1/9:1000.1000" bin-group
-------------------------------------------------------------------------------
Configured Lower Bounds for Delay Tests, in microseconds
-------------------------------------------------------------------------------
Group Description Admin Bin FD(us) FDR(us) IFDV(us)
-------------------------------------------------------------------------------
3 Up 0 0 0 0
1 1 500 250
2 500 1000 500
3 1000 1500 1000
4 2000 2000 1500
5 3000 2500 2000
6 4000 3000 2500
7 5000 3500 3000
8 5500 4000 3500
9 6500 4500 4000
-------------------------------------------------------------------------------
---------------------------------------
Bins Excluded from Average
---------------------------------------
Bin Type Direction Bins
---------------------------------------
FD round-trip 0,9
---------------------------------------
--------------------------------------------------------------------
Bins Excluded from Delay Event Count
--------------------------------------------------------------------
Bin Type Direction Lowest Excluded Bin Lower Bound (us)
--------------------------------------------------------------------
FD round-trip 9 6500
--------------------------------------------------------------------
show oam-pm session "vpls1000-PM-YL4-1/1/9:1000.1000" meas-interval
-------------------------------------------------------------------------------
5-mins Measurement Interval Configuration
-------------------------------------------------------------------------------
Duration : 5-mins Intervals Stored : 32
Boundary Type : clock-aligned Clock Offset : 0 seconds
Accounting Policy : none Event Monitoring : enabled
Delay Event Mon : enabled Loss Event Mon : enabled
-------------------------------------------------------------------------------
show oam-pm statistics session "eth-pm-service-1000" lmm meas-interval 15-
mins interval-number 2
------------------------------------------------------------------------------
Start (UTC) : 2014/07/08 03:15:00 Status : completed
Elapsed (seconds) : 900 Suspect : no
Frames Sent : 90 Frames Received : 90
------------------------------------------------------------------------------
------------------------------------------------------
Data Frames Sent Data Frames Received
------------------------------------------------------
Forward 900 900
Backward 18900 18900
------------------------------------------------------
----------------------------------------------
Frame Loss Ratios
----------------------------------------------
Minimum Maximum Average
----------------------------------------------
Forward 0.000% 0.000% 0.000%
Backward 0.000% 0.000% 0.000%
----------------------------------------------
-------------------------------------------------------------------------------
Availability Counters (Und = Undetermined)
-------------------------------------------------------------------------------
Available Und-Avail Unavailable Und-Unavail HLI CHLI
-------------------------------------------------------------------------------
Forward 90 0 0 0 0 0
Backward 90 0 0 0 0 0
-------------------------------------------------------------------------------
---------------------
Und-Delta-T
---------------------
Forward 0
Backward 0
---------------------
show oam-pm session "ies1500-PM-YL4-1/1/1:1500.1500"
-------------------------------------------------------------------------------
Basic Session Configuration
-------------------------------------------------------------------------------
Session Name : ies1500-PM-YL4-1/1/1:1500.1500
Description : (Not Specified)
Test Family : ethernet Session Type : proactive
Bin Group : 2
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Ethernet Configuration
-------------------------------------------------------------------------------
Source MEP : 30 Priority : 5 (fc ef)
Source Domain : 14 Dest MAC Address : none
Source Assoc'n : 1500 Remote MEP : 33
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
LMM Test Configuration and Status
-------------------------------------------------------------------------------
Test ID : 1 Admin State : Up
Oper State : Up Interval : 1000 ms
On-Demand Duration: Not Applicable On-Demand Remaining: Not Applicable
Availability : Disabled
CHLI Threshold : 5 HLIs Frames Per Delta-T : 10 LMM frames
Consec Delta-Ts : 10 FLR Threshold : 50%
Detectable Tx Err : none
Enable FC Collect : yes| no
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
5-mins Measurement Interval Configuration
-------------------------------------------------------------------------------
Duration : 5-mins Intervals Stored : 32
Boundary Type : clock-aligned Clock Offset : 0 seconds
Accounting Policy : none Event Monitoring : disabled
Delay Event Mon : disabled Loss Event Mon : disabled
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Configured Lower Bounds for Delay Tests, in microseconds
-------------------------------------------------------------------------------
Group Description Admin Bin FD(us) FDR(us) IFDV(us)
-------------------------------------------------------------------------------
2 Up 0 0 0 0
1 1 500 250
2 500 1000 500
3 1000 1500 1000
4 2000 2000 1500
5 3000 2500 2000
6 4000 3000 2500
7 5000 3500 3000
8 5500 4000 3500
9 6500 4500 4000
-------------------------------------------------------------------------------
session
Syntax
session [sap sap-id] [interface ip-int-name | ip-address] [mac ieee-address] [ circuit-id circuit-id] [remote-id remote-id] [ inter-dest-id intermediate-destination-id] [no-inter-dest-id] [ ip-address ip-prefix[/prefix-length]] [port port-id] [subscriber sub-ident-string] [sap-session-id sap-session-index]
session all
Context
[Tree] (clear>service>id>ipoe session)
Full Context
clear service id ipoe session
Description
This commands clears all identified IPoE sessions for the specified service instance. All associated subscriber hosts are deleted from the system.
Parameters
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- ip-int-name
-
Specifies the name of the IP interface up to 32 characters.
- ieee-address
-
Specifies the 48-bit MAC address for the static ARP in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd-ee-ff where aa, bb, cc, dd, ee, and ff are hexadecimal numbers. Allowed values are any non-broadcast, non-multicast MAC and non-IEEE reserved MAC addresses.
- circuit-id
-
Specifies the circuit ID up to 127 characters.
- remote-id
-
Specifies that information that goes into the remote-id sub-option in the DHCP relay packet, up to 255 characters.
- ip-address[/prefix-length]
-
Specifies information for the specified IP address and mask.
- no-inter-dest-id
-
Displays the information about no intermediate destination ID.
- intermediate-destination-id
-
Specifies the intermediate destination identifier which is encoded in the identification strings up to 32 characters.
- port-id
-
Displays information about the specified port ID.
- sap-session-index
-
Displays sap-session-index information.
- service-id
-
Specifies the service ID of the wholesaler.
- sub-ident-string
-
Specifies an existing subscriber identification profile.
- service-id
-
Specifies information for the specified service ID.
- detail
-
Displays all IPoE session details.
- all
-
clears all active IPoE sessions for the specified service instance.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
session
Syntax
session default-tunnel
session [sap sap-id] [mac mac-address] [local-session-id local-id] [remote-session-id remote-id] [detail]
Context
[Tree] (show>subscr-mgmt>pfcp session)
Full Context
show subscriber-mgmt pfcp session
Description
This command displays information on PFCP sessions, including the default session. By default, all sessions are shown; filters can be applied to reduce the number of sessions or select a specific session.
Parameters
- default-tunnel
-
Specifies that session information for the default tunnel is displayed.
- detail
-
Specifies that associated forwarding information is displayed.
- local-id
-
Specifies a local PFCP Session ID, up to 20 characters, which displays information for that local session ID.
- remote-id
-
Specifies a remote PFCP session ID, up to 20 characters, which displays information for that remote session ID.
- mac-address
-
Specifies the MAC address associated with the session, in the form xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx, which displays information associated with the specified MAC address.
- sap-id
-
Specifies the SAP ID associated with the session.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of this command.
Output ExampleA:BNG-UPF# show subscriber-mgmt pfcp session
===============================================================================
PFCP Sessions
===============================================================================
Local Session Id : 0x0000000000000001 (default*
Local Peer Address : 192.0.2.11
Local Router : to_cp
Local TE-ID : N/A
Remote Session Id : 0x0000000000010100
Remote Peer Address : 17.17.17.10
Remote TE-ID : 0x0001fff0
PFCP Association : smf
Data Upstream PDR-ID : N/A
Data Downstream PDR-ID : N/A
IBCP Upstream PDR-ID : 0x0a00
IBCP Downstream PDR-ID : N/A
StateId : N/A
Protocols : IPOE_DHCP4 PPPOE_DISC
===============================================================================
No. of PFCP Sessions: 1
===============================================================================
* indicates that the corresponding row element may have been truncated.
session
Syntax
session lsp-path [lsp-index lsp-index] [ path-lspid path-lspid] [prefix ip-prefix /prefix-length] [src ip-address | ipv6 address]
session lsp-path all
session sr-policy [lsp-index lsp-index] [ path-lspid path-lspid] [prefix ip-prefix /prefix-length] [src ip-address | ipv6 address]
session sr-policy all
Context
[Tree] (clear>router>bfd>seamless-bfd session)
Full Context
clear router bfd seamless-bfd session
Description
This command clears Seamless-BFD (S-BFD) session information.
Parameters
- lsp-path
-
Keyword to clear the S-BFD sessions for the LSP path.
- sr-policy
-
Keyword to clear the S-BFD sessions for the SR policy.
- all
-
Keyword to clear all S-BFD sessions.
- lsp-index lsp-index
-
Specifies the LSP index.
- path-lspid path-lspid
-
Specifies the path LSP ID.
- prefix
-
Keyword to clear information by far-end prefix.
- ip-prefix/prefix-length
-
Specifies an IP prefix for which to clear S-BFD session information, and the length of the prefix.
- ip-address | ipv6-address
-
Specifies the IP address for which to clear S-BFD session information.
Platforms
All
session
Syntax
session session-name
Context
[Tree] (monitor>oam-pm session)
Full Context
monitor oam-pm session
Description
This command monitors the raw measurement interval for the specified session and test.
Platforms
All
Output
The following output is an example of raw session measurement information.
Output Examplemonitor oam-pm session "eth-pm-service-4" dmm
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
---------------------------------------------------------------
Frame Delay (FD) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 3928 1125 0
1 1000 us 1197 1855 2611
2 2000 us 183 1361 1565
3 3000 us 36 762 778
4 4000 us 30 214 280
5 5000 us 14 45 81
6 6000 us 8 17 35
7 7000 us 1 5 16
8 8000 us 5 15 26
9 10000 us 1 4 11
---------------------------------------------------------------
---------------------------------------------------------------
Frame Delay Range (FDR) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 5374 5317 5321
1 5000 us 29 86 82
---------------------------------------------------------------
---------------------------------------------------------------
Inter-Frame Delay Variation (IFDV) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 2475 1268 625
1 100 us 516 676 554
2 200 us 395 479 417
3 300 us 338 451 398
4 400 us 224 291 340
5 500 us 185 212 280
6 600 us 187 137 234
7 700 us 185 134 208
8 800 us 315 223 392
9 1000 us 582 1531 1954
---------------------------------------------------------------
-------------------------------------------------------------------------------
At time t = 10 sec (Mode: Delta)
-------------------------------------------------------------------------------
---------------------------------------------------------------
Frame Delay (FD) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 0 7 0
1 1000 us 10 2 6
2 2000 us 0 1 3
3 3000 us 0 0 1
4 4000 us 0 0 0
5 5000 us 0 0 0
6 6000 us 0 0 0
7 7000 us 0 0 0
8 8000 us 0 0 0
9 10000 us 0 0 0
---------------------------------------------------------------
---------------------------------------------------------------
Frame Delay Range (FDR) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 10 10 10
1 5000 us 0 0 0
---------------------------------------------------------------
---------------------------------------------------------------
Inter-Frame Delay Variation (IFDV) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 5 4 2
1 100 us 2 2 2
2 200 us 2 1 1
3 300 us 1 0 0
4 400 us 0 0 1
5 500 us 0 0 0
6 600 us 0 0 0
7 700 us 0 0 1
8 800 us 0 0 0
9 1000 us 0 3 3
---------------------------------------------------------------
---------------------------------------------------------------
At time t = 20 sec (Mode: Delta)
---------------------------------------------------------------
---------------------------------------------------------------
Frame Delay (FD) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 9 0 0
1 1000 us 0 7 6
2 2000 us 0 3 3
3 3000 us 1 0 0
4 4000 us 0 0 0
5 5000 us 0 0 1
6 6000 us 0 0 0
7 7000 us 0 0 0
8 8000 us 0 0 0
9 10000 us 0 0 0
---------------------------------------------------------------
---------------------------------------------------------------
Frame Delay Range (FDR) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 10 10 10
1 5000 us 0 0 0
---------------------------------------------------------------
---------------------------------------------------------------
Inter-Frame Delay Variation (IFDV) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 5 3 2
1 100 us 0 2 2
2 200 us 0 1 0
3 300 us 0 3 1
4 400 us 2 0 0
5 500 us 1 0 0
6 600 us 0 1 2
7 700 us 0 0 0
8 800 us 0 0 0
9 1000 us 2 0 3
---------------------------------------------------------------
monitor oam-pm session "eth-pm-service-4" slm
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
------------------------------------------------------
Frames Sent Frames Received
------------------------------------------------------
Forward 54749 54749
Backward 54749 54749
------------------------------------------------------
-------------------------------------------------------------------------------
Availability Counters (Und = Undetermined)
-------------------------------------------------------------------------------
Available Und-Avail Unavailable Und-Unavail HLI CHLI
-------------------------------------------------------------------------------
Forward 5475 0 0 0 0 0
Backward 5475 0 0 0 0 0
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
At time t = 10 sec (Mode: Delta)
-------------------------------------------------------------------------------
------------------------------------------------------
Frames Sent Frames Received
------------------------------------------------------
Forward 100 100
Backward 100 100
------------------------------------------------------
-------------------------------------------------------------------------------
Availability Counters (Und = Undetermined)
-------------------------------------------------------------------------------
Available Und-Avail Unavailable Und-Unavail HLI CHLI
-------------------------------------------------------------------------------
Forward 10 0 0 0 0 0
Backward 10 0 0 0 0 0
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
At time t = 20 sec (Mode: Delta)
-------------------------------------------------------------------------------
------------------------------------------------------
Frames Sent Frames Received
------------------------------------------------------
Forward 100 100
Backward 100 100
------------------------------------------------------
-------------------------------------------------------------------------------
Availability Counters (Und = Undetermined)
-------------------------------------------------------------------------------
Available Und-Avail Unavailable Und-Unavail HLI CHLI
-------------------------------------------------------------------------------
Forward 10 0 0 0 0 0
Backward 10 0 0 0 0 0
-------------------------------------------------------------------------------
monitor oam-pm session "ip-vprn-500" twamp-light
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
---------------------------------------------------------------
Frame Delay (FD) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 89719 113813 82529
1 1000 us 51728 43288 62811
2 2000 us 19304 7882 16979
3 3000 us 5207 1300 3067
4 4000 us 1166 335 1280
5 5000 us 469 255 781
6 6000 us 227 129 361
7 7000 us 121 166 152
8 8000 us 83 253 114
9 10000 us 125 728 75
---------------------------------------------------------------
---------------------------------------------------------------
Frame Delay Range (FDR) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 167124 166618 167138
1 5000 us 1025 1531 1011
---------------------------------------------------------------
---------------------------------------------------------------
Inter-Frame Delay Variation (IFDV) Bin Counts
---------------------------------------------------------------
Bin Lower Bound Forward Backward Round Trip
---------------------------------------------------------------
0 0 us 29284 45291 36062
1 100 us 9615 10793 28238
2 200 us 9289 9827 20379
3 300 us 8933 8733 14325
4 400 us 8597 8362 10257
5 500 us 8216 7789 7635
6 600 us 8178 7606 5893
7 700 us 7782 7345 4963
8 800 us 14799 14500 8416
9 1000 us 63455 47902 31980
---------------------------------------------------------------
session
Syntax
session ldp-id [ldp-id] [interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor>router>ldp session)
Full Context
monitor router ldp session
Description
This command displays statistical information for LDP sessions at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the specified LDP session(s). The subsequent statistical information listed for each interval is displayed as a delta to the previous display.
When the keyword rate is specified, the rate-per-second for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor commands display the selected statistics according to the configured number of times at the interval specified.
Parameters
- ldp-id
-
Specifies the IP address of the LDP session to display. Up to five IP addresses can be specified in a single statement.
- seconds
-
Configures the interval for each display, in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
All
Output
The following output is an example of LDP session information.
Output ExampleA:ALA-103>monitor>router>ldp# session 10.10.10.104 interval 3 repeat 3 absolute
===============================================================================
Monitor statistics for LDP Session 10.10.10.104
===============================================================================
Sent Received
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
FECs 1 2
Hello 5288 5289
Keepalive 8225 8225
Init 1 1
Label Mapping 1 4
Label Request 0 0
Label Release 0 0
Label Withdraw 0 0
Label Abort 0 0
Notification 0 0
Address 1 1
Address Withdraw 0 0
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Absolute)
-------------------------------------------------------------------------------
FECs 1 2
Hello 5288 5289
Keepalive 8226 8226
Init 1 1
Label Mapping 1 4
Label Request 0 0
Label Release 0 0
Label Withdraw 0 0
Label Abort 0 0
Notification 0 0
Address 1 1
Address Withdraw 0 0
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Absolute)
-------------------------------------------------------------------------------
FECs 1 2
Hello 5288 5290
Keepalive 8226 8226
Init 1 1
Label Mapping 1 4
Label Request 0 0
Label Release 0 0
Label Withdraw 0 0
Label Abort 0 0
Notification 0 0
Address 1 1
Address Withdraw 0 0
-------------------------------------------------------------------------------
At time t = 9 sec (Mode: Absolute)
-------------------------------------------------------------------------------
FECs 1 2
Hello 5288 5290
Keepalive 8226 8226
Init 1 1
Label Mapping 1 4
Label Request 0 0
Label Release 0 0
Label Withdraw 0 0
Label Abort 0 0
Notification 0 0
Address 1 1
Address Withdraw 0 0
========================================================================
A:ALA-12>monitor>router>ldp#
A:ALA-12>monitor>router>ldp# session 10.10.10.104 interval 3 repeat 3 rate
===============================================================================
Monitor statistics for LDP Session 10.10.10.104
===============================================================================
Sent Received
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
FECs 1 2
Hello 5289 5290
Keepalive 8227 8227
Init 1 1
Label Mapping 1 4
Label Request 0 0
Label Release 0 0
Label Withdraw 0 0
Label Abort 0 0
Notification 0 0
Address 1 1
Address Withdraw 0 0
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Rate)
-------------------------------------------------------------------------------
FECs 0 0
Hello 0 0
Keepalive 0 0
Init 0 0
Label Mapping 0 0
Label Request 0 0
Label Release 0 0
Label Withdraw 0 0
Label Abort 0 0
Notification 0 0
Address 0 0
Address Withdraw 0 0
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Rate)
-------------------------------------------------------------------------------
FECs 0 0
Hello 0 0
Keepalive 0 0
Init 0 0
Label Mapping 0 0
Label Request 0 0
Label Release 0 0
Label Withdraw 0 0
Label Abort 0 0
Notification 0 0
Address 0 0
Address Withdraw 0 0
-------------------------------------------------------------------------------
At time t = 9 sec (Mode: Rate)
-------------------------------------------------------------------------------
FECs 0 0
Hello 0 0
Keepalive 0 0
Init 0 0
Label Mapping 0 0
Label Request 0 0
Label Release 0 0
Label Withdraw 0 0
Label Abort 0 0
Notification 0 0
Address 0 0
Address Withdraw 0 0
===============================================================================
A:ALA-12>monitor>router>ldp#
session
Syntax
session imsi imsi apn apn-string
session [peer-address ip-address] [ router router-instance] [remote-control-teid teid] [local-control-teid teid] [detail]
session imsi imsi
Context
[Tree] (show>subscr-mgmt>gtp>s11 session)
Full Context
show subscriber-mgmt gtp s11 session
Description
This command displays GTP S11 session information.
Parameters
- imsi
-
Specifies the IMSI (International Mobile Subscriber Identity) of this UE.
- apn-string
-
Specifies the APN (Access Point Name), up to 100 characters.
- ip-address
-
Specifies the IP address.
- router-instance
-
Specifies the identifier of the virtual router instance where the GTP tunnel is terminated.
- remote-control-teid teid
-
Specifies the remote control plane Tunnel Endpoint Identifier (TEID).
- local-control-teid teid
-
Specifies the local control plane TEID.
- detail
-
Displays detailed information.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of GTP S11 session information.
Output ExampleNode# show subscriber-mgmt gtp s11 session
===============================================================================
GTP S11 sessions
===============================================================================
IMSI : 001020000000001
APN : demo.mnc001.mcc001.gprs
-------------------------------------------------------------------------------
Peer router : 10
Peer address : 192.168.100.1
Remote control TEID : 1
Local control TEID : 4293919008
PDN TEID : 4293919008
Charging characteristics : (None)
Uplink AMBR (kbps) : 10000
Downlink AMBR (kbps) : 20000
Ipoe-session SAP : [pxc-1.b:1.8]
Ipoe-session Mac Address : 00:03:ff:f0:01:20
-------------------------------------------------------------------------------
No. of GTP S11 sessions: 1
===============================================================================
session
Syntax
session session-name
Context
[Tree] (show>oam-pm>stats session)
Full Context
show oam-pm statistics session
Description
This command selects the session for the statistical display.
Parameters
- session-name
-
Specifies the session name, up to 32 characters.
Platforms
All
session-filter
session-filter
Syntax
session-filter
session-filter session-filter-name
Context
[Tree] (show>app-assure>group session-filter)
Full Context
show application-assurance group session-filter
Description
This command displays session filter information.
Parameters
- session-filter-name
-
Specifies a session-filter-name up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the session-filter command information.
Output Exampleshow application-assurance group <aa-group-id>[:<partition>] session-filter <filter-
name>
# session-filter<filter-id>
========================================================================
AA Session Filter
========================================================================
Filter Name : Block UDP Session Initiation
Applied : Yes Def. Action : Permit
Entries : 1
Description : Block UDP initiated towards subscribers
------------------------------------------------------------------------
Filter Match Criteria
------------------------------------------------------------------------
Entry : 1
Description : (Not Specified)
Protocol : 17
Action : deny
Hit Count : 0 pkts
========================================================================
session-parameters
session-parameters
Syntax
session-parameters [family] [community community]
session-parameters peer-ip-address
Context
[Tree] (show>router>ldp session-parameters)
Full Context
show router ldp session-parameters
Description
This command displays LDP peer information.
Parameters
- peer-ip-address
-
Specify the peer IP address.
- family
-
Displays either IPv4 or IPv6 active LDP information.
- community
-
The string defining the LDP community assigned to the session. Allowed values are any string up to 32 characters long composed of printable, 7-bit ASCII characters excluding double quotes. If the string contains spaces, use double quotes to delimit the start and end of the string.
Platforms
All
Output
LDP Session Parameters Output Fields describes the LDP session-parameters output.
Label |
Description |
---|---|
Peer |
The IP address of the peer. |
TTL security |
Enabled — LDP peering sessions protected. Disabled — LDP peering sessions unprotected. |
Min-TTL-Value |
Displays the minimum TTL value for an incoming packet. |
Auth |
Enabled — Authentication using MD5 message based digest protocol is enabled. Disabled — No authentication is used. |
Example with community RED:
*A:SRU4# show router ldp session-parameters 10.20.1.1
===============================================================================
LDP IPv4 Session Parameters
===============================================================================
-------------------------------------------------------------------------------
Peer : 10.20.1.1
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Disabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise : Enabled
Community : RED
===============================================================================
No. of IPv4 Peers: 1
===============================================================================
* indicates that the corresponding row element may have been truncated.
Example without community
*A:Dut-A# show router ldp session-parameters
===============================================================================
LDP IPv4 Session Parameters
===============================================================================
-------------------------------------------------------------------------------
Peer : 10.20.1.2
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Disabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
-------------------------------------------------------------------------------
Peer : 10.20.1.3
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Disabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
-------------------------------------------------------------------------------
Peer : 10.20.1.6
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Enabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
===============================================================================
No. of IPv4 Peers: 3
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
LDP IPv6 Session Parameters
===============================================================================
-------------------------------------------------------------------------------
Peer : 3ffe::a14:102
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Disabled IPv6 Prefix Fec Cap: Enabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
-------------------------------------------------------------------------------
Peer : 3ffe::a14:103
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Disabled IPv6 Prefix Fec Cap: Enabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
===============================================================================
No. of IPv6 Peers: 2
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-A#
*A:Dut-A# show router ldp session-parameters 3ffe::a14:103
===============================================================================
LDP IPv6 Session Parameters
===============================================================================
-------------------------------------------------------------------------------
Peer : 3ffe::a14:103
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Disabled IPv6 Prefix Fec Cap: Enabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
===============================================================================
No. of IPv6 Peers: 1
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-A#
*A:Dut-A# show router ldp session-parameters ipv4
===============================================================================
LDP IPv4 Session Parameters
===============================================================================
-------------------------------------------------------------------------------
Peer : 10.20.1.2
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Disabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
-------------------------------------------------------------------------------
Peer : 10.20.1.3
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Disabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
-------------------------------------------------------------------------------
Peer : 10.20.1.6
-------------------------------------------------------------------------------
DOD : Disabled Adv Adj Addr Only : Disabled
FEC129 Cisco Inter*: Disabled
PE-ID MAC Flush In*: Disabled
Fec Limit : 0 Fec Limit Threshold: 90
Fec Limit Log Only : Disabled
Import Policies : None Export Policies : None
IPv4 Prefix Fec Cap: Enabled IPv6 Prefix Fec Cap: Enabled
P2MP Fec Cap : Enabled
Address Export : None
LSRID advertise :
Community :
===============================================================================
No. of IPv4 Peers: 3
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-A#
sessions
sessions
Syntax
sessions [group name] neighbor ip-address] [port port-number] [association] [ statistics]
Context
[Tree] (show>service>id>gsmp sessions)
Full Context
show service id gsmp sessions
Description
This command displays GSMP sessions information.
Parameters
- group
-
A GSMP group defines a set of GSMP neighbors which have the same properties.
- name
-
Specifies a GSMP group name is unique only within the scope of the service in which it is defined.
- ip-address
-
Specifies the ip-address of the neighbor.
- port
-
Specifies the neighbor TCP port number use for this ANCP session.
- association
-
Displays to what object the ANCP-string is associated.
- statistics
-
Displays statistics information about an ANCP session known to the system.
Platforms
All
Output
The following output is an example of GSMP sessions information.
Output ExampleThis show command gives information about the open TCP connections with DSLAMs.
A:active>show>service>id>gsmp# sessions
=======================================================
GSMP sessions for service 999 (VPRN)
=======================================================
Port Ngbr-IpAddr Gsmp-Group
-------------------------------------------------------
40590 192.168.1.2 dslam1
-------------------------------------------------------
Number of GSMP sessions : 1
=======================================================
A:active>show>service>id>gsmp#
A:active>show>service>id>gsmp# sessions neighbor 192.168.1.2 port 40590
=========================================================================
GSMP sessions for service 999 (VPRN), neighbor 192.168.1.2, Port 40590
=========================================================================
State : Established
Peer Instance : 1 Sender Instance : a3cf58
Peer Port : 0 Sender Port : 0
Peer Name : 12:12:12:12:12:12 Sender Name : 00:00:00:00:00:00
timeouts : 0 Max. Timeouts : 3
Peer Timer : 100 Sender Timer : 100
Capabilities : DTD OAM
Conf Capabilities : DTD OAM
Priority Marking : dscp nc2
Local Addr. : 192.168.1.4
Conf Local Addr. : N/A
=========================================================================
A:active>show>service>id>gsmp#
A:active>show>service>id>gsmp# sessions neighbor 192.168.1.2 port 40590 association
===============================================================================
ANCP-Strings
===============================================================================
ANCP-String Assoc. State
-------------------------------------------------------------------------------
No ANCP-Strings found
===============================================================================
A:active>show>service>id>gsmp#
A:active>show>service>id>gsmp# sessions neighbor 192.168.1.2 port 40590 statistics
===============================================================
GSMP session stats, service 999 (VPRN), neighbor 192.168.1.2, Port 40590
===============================================================
Event Received Transmitted
---------------------------------------------------------------
Dropped 0 0
Syn 1 1
Syn Ack 1 1
Ack 14 14
Rst Ack 0 0
Port Up 0 0
Port Down 0 0
OAM Loopback 0 0
===============================================================
A:active>show>service>id>gsmp#
The following table describes service ID GSMP sessions output fields:
Label |
Description |
---|---|
Port |
The port ID number |
Ngbr-IpAddr |
The neighbor IP address |
Gsmp-Group |
The GSMP group ID |
State |
The GSMP state of this TCP connection |
Peer Instance |
The unique GSMP ID for each end of the GSMP connection |
Peer Port |
The unique GSMP ID for each end of the GSMP connection |
Peer Name |
The unique GSMP ID for each end of the GSMP connection |
timeouts |
The number of successive timeouts for this session |
Peer Timer |
The GSMP keepalive timer |
Capabilities |
The ANCP capabilities negotiated for this session |
Conf Capabilities |
The ANCP capabilities configured for this session |
Priority Marking |
The priority marking configured for this session |
Local Addr |
The IP address used by the box's side of the TCP connection |
Conf. Local Addr. |
The configured IP address used by the box's side of the TCP connection |
Sender Instance |
The instance sent to the neighbor in this session |
Sender Port |
The port sent to the neighbor in this session |
Sender Name |
The name sent to the neighbor in this session |
Max. Timeouts |
The maximum number of successive timeouts configured for this session |
Sender Timer |
The timeout value that is announced toward the neighbor. The neighbor uses this timeout value while waiting for an acknowledgment from this system. |
The association command gives an overview of each ANCP string received from this session.
A:active>show>service>id>gsmp# sessions neighbor 192.168.1.2 port 40590 association
===============================================================================
ANCP-Strings
===============================================================================
ANCP-String Assoc.
State
-------------------------------------------------------------------------------
7330-ISAM-E47 atm 1/1/01/01:19425.64048 ANCP Up
-------------------------------------------------------------------------------
Number of ANCP-Strings : 1
===============================================================================
A:active>show>service>id>gsmp
sessions
Syntax
sessions [nat-group nat-group-id] [ mda mda-id] [protocol { gre | icmp | icmp6 | tcp | udp | unknown}] [inside-ip ip-prefix[/ ip-prefix-length]] [inside-router router-instance] [inside-port port-number] [ outside-ip ipv4-address] [outside-port port-number] [foreign-ip ip-address] [foreign-port port-number] [ dslite-address ipv6-address] [wlan-gw-ue ieee-address] [next-index index] [upnp] [ member member-id] [nat-policy policy-name] [dest-ip ip-address] [firewall-policy policy-name] [ address-type addr-type] [l2-aware-subscriber sub-ident]
Context
[Tree] (tools>dump>nat sessions)
Full Context
tools dump nat sessions
Description
This command dumps ISA sessions.
Parameters
- icmp
-
Specifies to dump only ICMP information.
- ieee-address
-
Specifies a MAC address, using the format xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx.
- ip-address
-
Specifies an IPv4 or IPv6 address.
- ipv4-address
-
Specifies an IPv4 address.
- ipv6-address
-
Specifies an IPv6 address.
- mda-id
-
Specifies an MDA ID.
- nat-group-id
-
Specifies a NAT group ID.
- policy-name
-
Specifies a policy name, up to 32 characters maximum.
- port-number
-
Specifies a port number.
- router-instance
-
Specifies a router name or service ID.
- tcp
-
Specifies to dump only TCP information.
- udp
-
Specifies to dump only UDP information.
- upnp
-
Specifies to dump only UPNP information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of this command.
Output Example*A:SR12_PPPOE# tools dump nat sessions
===============================================================================
Matched 2 sessions on Slot #3 MDA #1
===============================================================================
Owner : LSN-Host@10.2.3.4
Router : 100
FlowType : UDP PortFwd
Inside IP Addr : 10.2.3.4 Inside Port : 666
Outside IP Addr : 10.0.0.6 Outside Port : 666
Foreign IP Addr : * Foreign Port : *
Dest IP Addr : * Dest Port : *
-------------------------------------------------------------------------------
Owner : LSN-Host@10.2.3.4
Router : 100
FlowType : TCP PortFwd
Inside IP Addr : 10.2.3.4 Inside Port : 666
Outside IP Addr : 10.0.0.6 Outside Port : 666
Foreign IP Addr : * Foreign Port : *
Dest IP Addr : * Dest Port : *
-------------------------------------------------------------------------------
===============================================================================
===============================================================================
Matched 1 session on Slot #3 MDA #2
===============================================================================
Owner : LSN-Host@2001:db8:470:1F00:FFFF:189
Router : 100
FlowType : TCP Timeout (sec) : 6769
Inside IP Addr : 192.168.16.218 Inside Port : 41555
Outside IP Addr : 10.0.0.5 Outside Port : 1529
Foreign IP Addr : 10.0.0.1 Foreign Port : 22
Dest IP Addr : 10.0.0.1 Dest Port : 22
-------------------------------------------------------------------------------
===============================================================================
*A:SR12_PPPOE#
sessions
Syntax
sessions [test-family {ethernet | ip | mpls}]
sessions [test-family {ethernet | ip | mpls}] detectable-rx-errors
sessions [test-family {ethernet | ip | mpls}] detectable-tx-errors
sessions [test-family {ethernet | ip | mpls}] event-mon
sessions [test-family {ethernet | ip | mpls}] streaming delay
Context
[Tree] (show>oam-pm sessions)
Full Context
show oam-pm sessions
Description
This command shows a summary of the OAM Performance Monitoring sessions.
Parameters
- test-family
-
Shows all sessions that match the specified test family type when an optional filter is included.
- ethernet
-
Specifies Ethernet session types.
- ip
-
Specifies IP session types.
- mpls
-
Specifies MPLS session types.
- event-mon
-
Specifies a summary of all event monitoring and current state for each session.
- detectable-rx-errors
-
Specifies to display all MPLS sessions with a reported non-successful return code. The results of all return codes, other than "success”, are included. When a return code is not available it is reported as "none”. Sessions with a successful return code are filtered and not displayed in the list. This is specific to test-family mpls only.
- detectable-tx-errors
-
Specifies to provide a summary of tests with detectable transmission errors that prevent the test from sending packets. Not all errors are detectable.
- streaming delay
-
Displays all sessions with an assigned delay template.
Platforms
All
Output
The following output is an example of OAM-PM session summary information.
Output Exampleshow oam-pm sessions
============================================================================
OAM Performance Monitoring Session Summary for the Ethernet Test Family
============================================================================
Session State Bin Group Sess Type Test Types
----------------------------------------------------------------------------
vpls1000-PM-AL5-1/1/9:1000.1000 Act 2 proactive DMM SLM
vpls1000-PM-YL4-1/1/9:1000.1000 Act 3 proactive DMM SLM
============================================================================
============================================================================
OAM Performance Monitoring Session Summary for the IP Test Family
============================================================================
Session State Bin Group Sess Type Test Types
----------------------------------------------------------------------------
============================================================================
============================================================================
OAM Performance Monitoring Session Summary for the MPLS Test Family
============================================================================
Session State Bin Group Sess Type Test Types
----------------------------------------------------------------------------
mpls-dm-static-31-28 Act 2 proactive DM
mpls-dm-rsvp-31-to-28 Act 2 proactive DM
mpls-dm-rsvp-auto-31-to-28 Act 2 proactive DM
============================================================================
show oam-pm sessions event-mon
===============================================================================
OAM Performance Monitoring Event Summary for the Ethernet Test Family
===============================================================================
Event Monitoring Table Legend:
F = Forward, B = Backward, R = Round Trip, A = Aggregate,
- = Threshold Not Config, c = Threshold Config, * = TCA Active, P = Pending
===============================================================================
Test FD FDR IFDV FLR CHLI HLI UNAV UDAV UDUN
Session Type FBR FBR FBR FB FBA FBA FBA FBA FBA
-------------------------------------------------------------------------------
vpls1000-PM-AL5-1/1/9:1000.1000 DMM --- --- ---
vpls1000-PM-AL5-1/1/9:1000.1000 SLM -- --- --- --- --- ---
vpls1000-PM-YL4-1/1/9:1000.1000 DMM --c --- ---
vpls1000-PM-YL4-1/1/9:1000.1000 SLM -- --- --- --- --- ---
===============================================================================
===============================================================================
OAM Performance Monitoring Event Summary for the IP Test Family
===============================================================================
Event Monitoring Table Legend:
F = Forward, B = Backward, R = Round Trip, A = Aggregate,
- = Threshold Not Config, c = Threshold Config, * = TCA Active, P = Pending
===============================================================================
Test FD FDR IFDV FLR CHLI HLI UNAV UDAV UDUN
Session Type FBR FBR FBR FB FBA FBA FBA FBA FBA
-------------------------------------------------------------------------------
===============================================================================
show oam-pm sessions detectable-rx-errors
===============================================================================
OAM Performance Monitoring Receive Error Summary: MPLS Test Family
===============================================================================
Test
Session Type MPLS DM Receive Status
-------------------------------------------------------------------------------
S0 DM unexpected MPLS test Rx status code
S2 DM Notify: Data Format Invalid
S3 DM Notify: Initialization in Progress
S4 DM Notify: Data Reset Occurred
S5 DM Notify: Resource Temporarily Unavail
S6 DM unexpected MPLS test Rx status code
S16 DM Error: Unspecified Error
S17 DM Error: Unsupported Version
S18 DM Error: Unsupported Control Code
S19 DM Error: Unsupported Data Format
S20 DM Error: Authentication Failure
S21 DM Error: Invalid Destination Node Id
S22 DM Error: Connection Mismatch
S23 DM Error: Unsupported Mand TLV Object
S24 DM Error: Unsupported Query Interval
S25 DM Error: Administrative Block
S26 DM Error: Resource Unavailable
S27 DM Error: Resource Released
S28 DM Error: Invalid Message
S29 DM Error: Protocol Error
S30 DM unexpected MPLS test Rx status code
S256 DM none
S257 DM Error: Timeout
S258 DM unexpected MPLS test Rx status code
===============================================================================
show oam-pm sessions detectable-tx-errors
===============================================================================
OAM Performance Monitoring Transmit Error Summary: Ethernet Test Family
===============================================================================
Test
Session Type Detectable Transmit Error
-------------------------------------------------------------------------------
vpls1000-PM-YL4-1/1/9:1000.1000 DMM MEP is administratively down
vpls1000-PM-YL4-1/1/9:1000.1000 SLM MEP is administratively down
===============================================================================
===============================================================================
OAM Performance Monitoring Transmit Error Summary: IP Test Family
===============================================================================
Test
Session Type Detectable Transmit Error
-------------------------------------------------------------------------------
===============================================================================
show oam-pm sessions streaming delay
===============================================================================
OAM-PM Streaming Delay Summary for the Ethernet Test Family
===============================================================================
Session Test Type Test State Str Template Admin
-------------------------------------------------------------------------------
eth-circuit-service-epipe1 DMM Inact Up
===============================================================================
===============================================================================
OAM-PM Streaming Delay Summary for the IP Test Family
===============================================================================
Session Test Type Test State Str Template Admin
-------------------------------------------------------------------------------
ip-lpb111-SR-TE-LSP TWL Act Up
ip-circuit-service-vprn2 TWL Act Up
ip-rtr-telemetry-streaming TWL Act Up
===============================================================================
===============================================================================
OAM-PM Streaming Delay Summary for the MPLS Test Family
===============================================================================
Session Test Type Test State Str Template Admin
-------------------------------------------------------------------------------
mpls-dm-rsvp-PE-2-PE-1 DM Act Up
mpls-dm-static-PE-2-PE-1 DM Act Up
mpls-dm-rsvp-PE-2-PE-1-hop1 DM Act Up
mpls-dm-rsvp-auto-PE-2-PE-1 DM Act Template Not Found
===============================================================================
set-epoch-value
set-epoch-value
Syntax
set-epoch-value value
Context
[Tree] (tools>perform>router>pcp-server set-epoch-value)
Full Context
tools perform router pcp-server set-epoch-value
Description
This command sets the epoch value for a specified PCP server.
Parameters
- value
-
Specifies the epoch value.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
set-fabric-speed
set-fabric-speed
Syntax
set-fabric-speed fabric-speed
Context
[Tree] (tools>perform>system set-fabric-speed)
Full Context
tools perform system set-fabric-speed
Description
This command configures the fabric speed. This command is necessary to define the mode of operation for the system.
Default
set-fabric-speed none (for the 7750 SR-7s/14s FP4 and 7950 XRS systems)
set-fabric-speed fabric-speed-d (or the 7750 SR-7s/14s FP5 systems)
set-fabric-speed fabric-speed-a (for the other 7750 SR and 7450 ESS systems)
Parameters
- fabric-speed
-
Specifies the fabric speed of the system.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-7s, 7750 SR-14s, 7950 XRS
set-role
set-role
Syntax
set-role {extension | master | standalone}
Context
[Tree] (tools>perform>chassis set-role)
Full Context
tools perform chassis set-role
Description
This command sets the role of the 7950 XRS chassis from which the command is invoked.
-
When run on a standalone chassis this will update the EEPROM on the (one) Chassis backplane.
-
Master and Extension chassis are blocked if any SFMs are configured as type sfm-x20 (must be sfm-x20-b). The following message displays:
-
When the extension option is specified, the chassis will immediately reboot as part of the command. The following warning and prompt will be provided:
WARNING: You are about to provision the chassis as an XRS-40 Extension chassis. This chassis will immediately reboot after the command is executed. No CLI shell is available directly on an Extension chassis. An Extension chassis will not completely boot up unless it is properly cabled to and controlled by an XRS-40 Master chassis. Do you wish to proceed (yes/no) ?
-
When the master option is specified, the chassis will immediately reboot as part of the command. The Operational mode is not changed until a reboot is performed. The following warning and prompt will be provided:
WARNING: You are about to provision the chassis as an XRS- 40 Master chassis. This chassis will immediately reboot after the command is execute Do you wish to proceed (yes/no) ?
-
When the master or extension options are specified and the chassis has any SFM slots with a configured type of sfm-x20, then the command will fail with the following message:
Configured sfm-type of sfm-x20 is not compatible with XRS-40 mode operation.
If you want to change the role of the chassis anyways, you can deconfigure the SFMs and then change the role.
Platforms
7950 XRS
set-trim-mode
set-trim-mode
Syntax
set-trim-mode set-trim-mode
Context
[Tree] (tools>perform>system set-trim-mode)
Full Context
tools perform system set-trim-mode
Description
This command should only be used with authorized direction of Nokia technical support.
Parameters
- set-trim-mode
-
Specifies the trim operating mode for the system.
Platforms
7450 ESS, 7750 SR-7/12/12e
sflow
sflow
Syntax
sflow
Context
[Tree] (show sflow)
Full Context
show sflow
Description
This command displays the primary and backup receiver statistics, the mapping configuration and a summary of how many ports and SAPs have sFlow enabled.
Platforms
7750 SR, 7750 SR-s, 7950 XRS
Output
The following output is an example of sFlow information. Show sFlow Output Fields describes the show sFlow output fields.
Output Example*B:bkvm10# show sflow
===============================================================================
sFlow Status
===============================================================================
Receiver : pat
Max Data Size : 312
IP Addr Primary : 10.120.142.163:6343
Packets Sent : 2572
Packet Errors : 2
Last Packet Sent : 07/08/2014 22:23:57nt
IP Addr Backup : N/A
Packets Sent : 0
Packet Errors : 0
Last Packet Sent : No Pkts sent
-----------------------------------
Counter Pollers
-----------------------------------
Port No. of SAPs
-----------------------------------
1/1/2 3
1/2/1 0
-----------------------------------
No. of sFlow counter pollers: 2
-----------------------------------
--------------------------------------------------
Counter Mappings
--------------------------------------------------
Direction Policer/Queue Traffic Type
--------------------------------------------------
egress queue 1 unicast
egress queue 5 multicast
egress queue 8 broadcast
ingress policer 1 unicast
ingress policer 6 multicast
ingress policer 12 broadcast
--------------------------------------------------
No. of sFlow counter mappings: 6
--------------------------------------------------
===============================================================================
Label |
Description |
---|---|
sFlow Status |
|
Receiver |
Displays the configured name for the sFlow receiver. |
Max Data Size |
The configured maximum data size for sFlow UDP packets. |
IP Addr Primary |
The primary IP address and destination port for sFlow receiver. |
IP Addr Backup |
The backup IP address and destination port for sFlow receiver. |
Packets Sent |
The number of packets sent successfully to the primary or backup receiver destination, since the destination was configured, CPM card HA switchover, or system reboot. |
Packet Errors |
The number of packets that could not be sent to the primary or backup receiver destination because of an error, since the destination was configured, CPM card HA switchover, or system reboot. An example of an error is destination IP not reachable. |
Last Packet Sent |
Displays the date and time of the last packet sent. |
Counter Pollers |
|
Port |
Displays the port on which sFlow is enabled. |
No. of SAPs |
The number of SAPs on the port with sFlow enabled. |
No. of sFlow counter pollers |
The number of sFlow counter pollers. |
Counter Mappings |
|
Direction |
Displays the direction of traffic (ingress or egress) the map entry applies to. |
Policer/Queue |
Displays the policer or queue instance being mapped by sFlow map. |
Traffic type |
Displays the type of sFlow traffic statistics (unicast, multicast or broadcast) that the policer/queue maps to. |
No. of sFlow counter mappings |
The number of entries in the sFlow ingress and egress counter map. |
sfm
sfm
Syntax
sfm sfm-name [force]
Context
[Tree] (clear sfm)
Full Context
clear sfm
Description
This command resets the SFM.
Parameters
- sfm-name
-
Specifies the SFM identifier.
- force
-
Performs the reset without a confirmation prompt.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-2s, 7750 SR-2se, 7750 SR-7s, 7750 SR-14s, 7950 XRS
sfm
Syntax
sfm [sfm-name] [detail]
sfm [sfm-name] icport [down] [ degraded]
Context
[Tree] (show sfm)
Full Context
show sfm
Description
This command displays SFM status information.
Parameters
- sfm-name
-
Specifies the SFM identifier.
- icport
-
Displays interconnect port information.
- down
-
Displays interconnect ports that are not operational.
- degraded
-
Displays interconnect ports that are associated with fabric degradation.
- detail
-
Displays detailed information about the SFM.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-2s, 7750 SR-2se, 7750 SR-7s, 7750 SR-14s, 7950 XRS
Output
See the following output examples:
A:7950 XRS-20# show sfm
===============================================================================
SFM Summary
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
1 sfm-x20 up up
2 sfm-x20 up up
3 sfm-x20 up up
4 sfm-x20 up up
5 sfm-x20 up up
6 (not provisioned) up unprovisioned
sfm-x20
7 (not provisioned) up unprovisioned
sfm-x20
8 (not provisioned) up unprovisioned
sfm-x20
===============================================================================
Output Example: show sfm <sfm-id> detail
A:7950 XRS-20# show sfm 2 detail
===============================================================================
Fabric 2
===============================================================================
Slot Provisioned Type Admin Operational Comments
Equipped Type (if different) State State
-------------------------------------------------------------------------------
2 (not provisioned) up unprovisioned
sfm-x20
Hardware Data
Part number : xx
CLEI code : xx
Serial number : xx
Manufacture date : xx
Manufacturing string : xx
Manufacturing deviations : xx
Manufacturing assembly number : xx
Administrative state : up
Operational state : unprovisioned
Time of last boot : N/A
Current alarm state : alarm cleared
===============================================================================
Inter Chassis SFM Interconnect
SFM Interconnect Port 1
oper state : no-link
Misconnect Info : Fabric 3 IcPort 14
SFF Status : not-equipped
fabric degrade state : none
Output Example: show sfm icport
*A:myNode# show sfm icport
===============================================================================
SFM Interconnect Port Summary
===============================================================================
SFMSFM IcPort IcPort Module Degrade Miscon.Info
Oper State Num Oper State Inserted State SFM IcPort
-------------------------------------------------------------------------------
1 unprovisioned 1 up yes none
1 unprovisioned 2 invalid-conne* no degraded 3 14
2 up 2 indeterminate no none
2 up 3 up no degraded
2 up 5 no-link no none
2 up 14 indeterminate yes degraded
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
*A:myNode# show sfm icport down
===============================================================================
SFM Interconnect Port Summary
===============================================================================
SFM SFM IcPortIcPortModuleDegradeMiscon. Info
Oper StateNumOper StateInsertedStateSFMIcPort
-------------------------------------------------------------------------------
1 unprovisioned 2invalid-conne*nodegraded 3 14
2 up 2indeterminatenonone
2 up5no-linknonone
2 up14indeterminateyesdegraded
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:myNode# show sfm icport degraded
===============================================================================
SFM Interconnect Port Summary
===============================================================================
SFM SFMIcPortIcPortModuleDegradeMiscon. Info
Oper StateNumOper StateInserted State SFM IcPort
-------------------------------------------------------------------------------
2 up 3 up no degraded
2 up 14 indeterminate yes degraded
===============================================================================
Output Fields: show sfm
Output Fields: show sfm describes output fields for the show sfm command.
Label |
Description |
---|---|
Slot |
The number of the slot in which the SFM is installed. |
Provisioned Type Equipped Type (if different) |
The SFM type provisioned. |
Admin State |
The administrative state. |
Operational State |
The operational state. |
Hardware Data |
|
Part number |
The SFM part number. |
CLEI code |
The SFM CLEI code. |
Serial number |
The SFM serial number. |
Manufacture date |
The date the SFM was manufactured. |
Manufacturing deviations |
Specifies any manufacturing deviations. |
Manufacturing assembly number |
The SFM assembly number. |
Administrative state |
Specifies the administrative state of the SFM. |
Operational state |
Specifies the operational state of the SFM. |
Time of last boot |
Indicates the time stamp of the last system restart. |
Current alarm state |
Indicates the current alarm state. |
Inter Chassis SFM Interconnect |
|
SFM Interconnect Port |
Port number of the interconnect port. |
oper state |
Up — The SFM is administratively up. Down — The SFM is administratively down. |
Misconnect Info |
Only displayed if the oper state is invalid-connection. |
SFF Status |
The SFF status |
fabric degrade state |
Indicates state. |
sfm-interco-test
sfm-interco-test
Syntax
sfm-interco-test [sfm x]
Context
[Tree] (tools>perform>system>inter-chassis sfm-interco-test)
Full Context
tools perform system inter-chassis sfm-interco-test
Description
Use this command to run inter-chassis SFM loopback tests for the 7950 XRS.
Run on an out-of-service standalone chassis that will later become the Extension chassis of an XRS-40 system. The out of service chassis (Chassis 1 – future Master chassis) must be connected by means of SFM interconnect links (cable bundles) before this test is run. This test operates without requiring any XCMs in either chassis, but they can be present.
The test should not be initiated from Chassis 1.
The following conditions must be satisfied for the test to be permitted:
-
The system must be in standalone mode; error message:
The test can only be performed on a standalone system
-
The system must have only XRS-40 compatible SFMs provisioned; error message:
The chassis can not have SFMs with a configured type of sfm-x20s-b
when performing the test
-
All provisioned SFMs must be operational; error message:
All provisioned SFMs must be operational before performing the test
-
The same test cannot be running in another session (that is, only one test can be executed at a time); error message:
The test is already in-progress in another session
Other notes (which are also relayed to the operator when the test is attempted):
-
All provisioned XCMs will be reset at the start of the test and will be held in the booting state until the test has completed.
-
All SFMs will be cleared when the operator exits the test. This will trigger a reset of the XCMs and the standby CPM.
Platforms
7950 XRS
Output
The following output is an example of SFM interconnection test information.
Output Example*A:Dut-A# tools perform system inter-chassis sfm-interco-test
WARNING: This test is intended for an out-of-service standalone chassis that is
going to later become the extension chassis of an XRS-40 system.
At the start of the test, all provisioned IOMs will be reset and will be held
in the 'booting' state until the test has completed.
While the test is running avoid altering this system or the attached system
(e.g. do not shutdown, clear, or remove the CPMs/SFMs/IOMs and do not issue
CPM switchovers)
Once testing has completed all SFMs in this system will be cleared.
Do you wish to proceed (y/n)? y
Clearing provisioned IOMs ...
Test executing ...
Displaying results
===============================================================================
SFM Interconnect Port Summary
===============================================================================
SFM SFM IcPort IcPort Module Degrade Miscon Info
Oper State Num Oper State Inserted State SFM IcPort
-------------------------------------------------------------------------------
1 up 1 up yes none
1 up 2 up yes none
1 up 3 up yes none
1 up 4 up yes none
1 up 5 up yes none
1 up 6 up yes none
1 up 7 up yes none
1 up 8 up yes none
1 up 9 up yes none
1 up 10 up yes none
1 up 11 up yes none
1 up 12 up yes none
1 up 13 up yes none
1 up 14 up yes none
2 up 1 up yes none
2 up 2 up yes none
2 up 3 up yes none
2 up 4 up yes none
2 up 5 up yes none
2 up 6 up yes none
2 up 7 up yes none
2 up 8 up yes none
2 up 9 up yes none
2 up 10 up yes none
2 up 11 up yes none
2 up 12 up yes none
2 up 13 up yes none
2 up 14 up yes none
3 up 1 up yes none
3 up 2 up yes none
3 up 3 up yes none
3 up 4 up yes none
3 up 5 up yes none
3 up 6 up yes none
3 up 7 up yes none
3 up 8 up yes none
3 up 9 up yes none
3 up 10 up yes none
3 up 11 up yes none
3 up 12 up yes none
3 up 13 up yes none
3 up 14 up yes none
4 up 1 up yes none
4 up 2 up yes none
4 up 3 up yes none
4 up 4 up yes none
4 up 5 up yes none
4 up 6 up yes none
4 up 7 up yes none
4 up 8 up yes none
4 up 9 up yes none
4 up 10 up yes none
4 up 11 up yes none
4 up 12 up yes none
4 up 13 up yes none
4 up 14 up yes none
5 up 1 up yes none
5 up 2 up yes none
5 up 3 up yes none
5 up 4 up yes none
5 up 5 up yes none
5 up 6 up yes none
5 up 7 up yes none
5 up 8 up yes none
5 up 9 up yes none
5 up 10 up yes none
5 up 11 up yes none
5 up 12 up yes none
5 up 13 up yes none
5 up 14 up yes none
6 up 1 up yes none
6 up 2 up yes none
6 up 3 up yes none
6 up 4 up yes none
6 up 5 up yes none
6 up 6 up yes none
6 up 7 up yes none
6 up 8 up yes none
6 up 9 up yes none
6 up 10 up yes none
6 up 11 up yes none
6 up 12 up yes none
6 up 13 up yes none
6 up 14 up yes none
7 up 1 up yes none
7 up 2 up yes none
7 up 3 up yes none
7 up 4 up yes none
7 up 5 up yes none
7 up 6 up yes none
7 up 7 up yes none
7 up 8 up yes none
7 up 9 up yes none
7 up 10 up yes none
7 up 11 up yes none
7 up 12 up yes none
7 up 13 up yes none
7 up 14 up yes none
8 up 1 up yes none
8 up 2 up yes none
8 up 3 up yes none
8 up 4 up yes none
8 up 5 up yes none
8 up 6 up yes none
8 up 7 up yes none
8 up 8 up yes none
8 up 9 up yes none
8 up 10 up yes none
8 up 11 up yes none
8 up 12 up yes none
8 up 13 up yes none
8 up 14 up yes none
===============================================================================
Correct any mis-cabling and replace any suspected faulty equipment. Press Q to
quit the test or any other key to run the test again. q
Test complete, clearing the SFMs to return them to normal operational state.
Done. Exiting test.
sgt-qos
sgt-qos
Syntax
sgt-qos
Context
[Tree] (show>router sgt-qos)
Full Context
show router sgt-qos
Description
This command displays QoS information for self-generated traffic. In the output, "none” means that the default values for each application are used, not that there is no value set. For a list of application defaults, refer to "QoS for Self-Generated (CPU) Traffic on Network Interfaces” in the 7450 ESS, 7750 SR, 7950 XRS, and VSR Quality of Service Guide.
Platforms
All
sham-link
sham-link
Syntax
sham-link [interface-name] [detail]
sham-link interface-name remote ip-address [detail]
Context
[Tree] (show>router>ospf sham-link)
Full Context
show router ospf sham-link
Description
This command displays OSPFv2 sham-link neighbor information.
Parameters
- interface-name
-
Displays only the sham link identified by this interface name, up to 32 characters.
- remote
-
Displays sham-link information for the sham link identified by the specified remote IP address.
- ip-address
-
Displays only the sham link identified by this IP address.
Platforms
All
Output
The following output is an example of OSPFv2 sham-link neighbor information and Sham Links Output Fields describes the output fields.
Output Exampleshow router 1 ospf sham-link detail
===============================================================================
Rtr vprn1 OSPFv2 Instance 0 Sham-Links (detail)
===============================================================================
-------------------------------------------------------------------------------
Interface: myshamif1 Remote Nbr: 50.0.1.2
-------------------------------------------------------------------------------
Local IP Address : 50.0.1.1
Area Id : 0.0.0.0 Last Enabled : 08/12/2021 13:09:05
Admin Status : Enabled Oper State : Point To Point
Transit Delay : 1 sec Retrans Intrvl : 5 sec
Hello Intrvl : 1 sec Rtr Dead Intrvl : 3 sec
Cfg Metric : 10 Auth Type : None
If Events : 1
Tot Rx Packets : 0 Tot Tx Packets : 32
Rx Hellos : 0 Tx Hellos : 32
Rx DBDs : 0 Tx DBDs : 0
Rx LSRs : 0 Tx LSRs : 0
Rx LSUs : 0 Tx LSUs : 0
Rx LS Acks : 0 Tx LS Acks : 0
Discards : 0 Tx Failures : 0
Retransmits : 0
Bad Networks : 0
Bad Areas : 0 Bad Dest Addrs : 0
Bad Auth Types : 0 Auth Failures : 0
Bad Neighbors : 0 Bad Pkt Types : 0
Bad Lengths : 0 Bad Hello Int. : 0
Bad Dead Int. : 0 Bad Options : 0
Bad Versions : 0 Bad Checksums : 0
===============================================================================
Label |
Description |
---|---|
If Name |
IP interface name |
Nbr IP |
IP address of the neighbor |
Metric |
The metric associated with the interface |
Adm |
The administrative state of the interface |
Oper |
The operational state of the interface |
No. of OSPF Sham-links |
Number of sham links configured |
Tx Failures |
Transmitted OSPF packets that are dropped due to resource shortage |
sham-link-neighbor
sham-link-neighbor
Syntax
sham-link-neighbor [detail]
sham-link-neighbor interface-name remote ip-address [detail]
Context
[Tree] (show>router>ospf sham-link-neighbor)
Full Context
show router ospf sham-link-neighbor
Description
This command displays OSPFv2 sham-link neighbor information.
Parameters
- interface-name
-
Displays only the sham-link neighbor identified by this interface name, up to 32 characters.
- remote
-
Displays sham-link neighbor information for the neighbor identified by the specified remote IP address.
- ip-address
-
Displays only the sham-link neighbor identified by this IP address.
Platforms
All
shared-queue
shared-queue
Syntax
shared-queue [shared-queue-policy-name] [detail]
Context
[Tree] (show>qos shared-queue)
Full Context
show qos shared-queue
Description
This command displays shared-queue policy information.
Parameters
- shared-queue-policy-name
-
The shared-queue policy name.
- detail
-
Displays detailed information about the shared-queue policy.
Platforms
All
Output
The following output is an example of shared-queue QoS policy information, and Show QoS Shared Queue Output Fields describes shared-queue QoS policy output fields.
Output Example*A:PE# show qos shared-queue
===============================================================================
Shared Queue Policies
===============================================================================
Policy-Id Description
-------------------------------------------------------------------------------
default Default Shared Queue Policy
policer-output-queues Default Policer Output Shared Queue Policy
egress-pbr-ingress-queues Egress PBR Ingress Shared Queue Policy
===============================================================================
*A:PE#
Label |
Description |
---|---|
Policy |
The ID that uniquely identifies the policy. |
Description |
A text string that helps identify the policy context in the configuration file. |
shcv-policy
shcv-policy
Syntax
shcv-policy [policy-name]
Context
[Tree] (show>subscr-mgmt shcv-policy)
Full Context
show subscriber-mgmt shcv-policy
Description
This command displays the SHCV policy parameters.
Parameters
- policy-name
-
Specifies the SHCV policy name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of SHCV policy information. SHCV Policy Field Descriptions describes the output fields.
Output Example# show subscriber-mgmt shcv-policy "shcv-1"
===============================================================================
SHCV policy "shcv-1"
===============================================================================
Description : (Not Specified)
Last management change : 09/27/2021 09:50:58
VPLS
IPv4 source address : (Not Specified)
Source MAC address : (Not Specified)
Layer 3
Source IP address origin : interface
Unnumbered source IP address: (Not Specified)
Periodic
Administrative state : enabled
Action : alarm
Interval (minutes) : 30
Retry count : 2
Retry timeout (s) : 10
-------------------------------------------------------------------------------
Triggered
-------------------------------------------------------------------------------
ip-conflict
Administrative state : enabled
Retry count : 1
Retry timeout (s) : 1
host-limit-exceeded
Administrative state : enabled
Retry count : 1
Retry timeout (s) : 1
inactivity
Administrative state : enabled
Retry count : 2
Retry timeout (s) : 10
mobility
Administrative state : enabled
Retry count : 1
Retry timeout (s) : 1
mac-learning
Administrative state : enabled
Retry count : 2
Retry timeout (s) : 10
===============================================================================
Label |
Description |
---|---|
Description |
Displays the SHCV policy description |
Last management change |
Displays the date and time when the policy was last changed |
VPLS |
SHCV parameters applicable for VPLS services |
IPv4 source address |
Displays the IPv4 source address (sender IP address) used in SHCV ARP requests sent to host addresses learned using DHCP snooping in a VPLS service |
Source MAC address |
Displays the source MAC address used in SHCV ARP requests sent to host addresses learned using DHCP snooping in a VPLS service |
Layer 3 |
SHCV parameters applicable for Layer 3 services |
Source IP address origin |
Displays the source IP address origin:
|
Unnumbered source IP address |
Displays the IPv4 source address (sender IP address) used in SHCV ARP requests for unnumbered hosts |
Periodic |
SHCV parameters applicable for periodic and OAM checks |
Administrative state |
Displays the administrative state for periodic and OAM checks (enabled, disabled) |
Action |
Displays the action for unsuccessful checks:
|
Interval (minutes) |
Displays the interval between subsequent periodic checks |
Retry count |
Displays the number of SHCV check retries when no response is received withing the retry timeout interval |
Retry timeout (s) |
Displays the time to wait for an SHCV check response before the next retry or execution of the SHCV unsuccessful check action |
Triggered |
SHCV parameters applicable for triggered checks |
ip-conflict |
SHCV parameters applicable for checks triggered by an IP conflict: a new host with different MAC address and same IP address as an existing host active on the same SAP |
Administrative state |
Displays the administrative state for ip-conflict triggered checks (enabled, disabled) |
Retry count |
Displays the number of SHCV check retries when no response is received withing the retry timeout interval |
Retry timeout (s) |
Displays the time to wait for an SHCV check response before the next retry or deletion of the existing host from the system |
host-limit-exceeded |
SHCV parameters applicable for checks triggered by a host limit exceeded event |
Administrative state |
Displays the administrative state for host-limit-exceeded triggered checks (enabled, disabled) |
Retry count |
Displays the number of SHCV check retries when no response is received withing the retry timeout interval |
Retry timeout (s) |
Displays the time to wait for an SHCV check response before the next retry or deletion of the unresponsive existing host from the system |
inactivity |
SHCV parameters applicable for checks triggered by an inactivity detection |
Administrative state |
Displays the administrative state for host-limit-exceeded triggered checks (enabled, disabled) |
Retry count |
Displays the number of SHCV check retries when no response is received withing the retry timeout interval |
Retry timeout (s) |
Displays the time to wait for an SHCV check response before the next retry or deletion of the unresponsive inactive host from the system |
mobility |
SHCV parameters applicable for checks triggered by a mobility event: a new host with same MAC address and same IP address as an existing host active on a different SAP |
Administrative state |
Displays the administrative state for mobility triggered checks (enabled, disabled) |
Retry count |
Displays the number of SHCV check retries when no response is received withing the retry timeout interval |
Retry timeout (s) |
Displays the time to wait for an SHCV check response before the next retry or deletion of the existing host from the system |
mac-learning |
SHCV parameters applicable for checks triggered for mac learning of IP only static hosts |
Administrative state |
Displays the administrative state for mac-learning triggered checks (enabled, disabled) |
Retry count |
Displays the number of SHCV check retries when no response is received withing the retry timeout interval |
Retry timeout (s) |
Displays the time to wait for an SHCV check response before the next retry |
sid-egress-stats
sid-egress-stats
Syntax
sid-egress-stats adj [interface-name]
sid-egress-stats adj-set [id]
sid-egress-stats all
sid-egress-stats node [ip-prefix[/ prefix-length]]
Context
[Tree] (clear>router>isis sid-egress-stats)
[Tree] (clear>router>ospf sid-egress-stats)
Full Context
clear router isis sid-egress-stats
clear router ospf sid-egress-stats
Description
This command clears the IS-IS or OSPF egress SID statistics.
Parameters
- adj
-
Clears the egress statistics of the adjacency SID specified by the corresponding interface name. Clears all adjacency SIDs egress statistics if no adjacency SID is specified.
- interface-name
-
Clears the SID egress statistics for the interface specified by this interface name up to 32 characters.
- adj-set
-
Clears the egress statistics of the adjacency set specified by the corresponding ID. Clears all adjacency sets egress statistics if no adjacency set is specified.
- id
-
Clears the SID egress statistics for the identifier specified for this adjacency set.
- all
-
Clears all the SID egress statistics.
- node
-
Clears the egress statistics for the node SID specified by the corresponding prefix. Clears all node SIDs egress statistics if no node SID is specified.
- ip-prefix[/prefix-length]
-
Clears the IP prefix and prefix length of the node SID.
Platforms
All
sid-egress-stats
Syntax
sid-egress-stats adj [interface-name]
sid-egress-stats all
sid-egress-stats node [ip-prefix[/ prefix-length]]
Context
[Tree] (clear>router>ospf3 sid-egress-stats)
Full Context
clear router ospf3 sid-egress-stats
Description
This command clears the OSPF3 egress SID statistics.
Parameters
- adj
-
Clears the egress statistics of the adjacency SID specified by the corresponding interface name. Clears all adjacency SIDs egress statistics if no adjacency SID is specified.
- interface-name
-
Clears the SID egress statistics for the interface specified by this interface name up to 32 characters.
- all
-
Clears all the SID egress statistics.
- node
-
Clears the egress statistics for the node SID specified by the corresponding prefix. Clears all node SIDs egress statistics if no node SID is specified.
- ip-prefix[/prefix-length]
-
Clears the IP prefix and prefix length of the node SID.
Platforms
All
sid-ingress-stats
sid-ingress-stats
Syntax
sid-ingress-stats adj [interface-name]
sid-ingress-stats adj-set [id]
sid-ingress-stats all
sid-ingress-stats node [ip-prefix[/ prefix-length]]
Context
[Tree] (clear>router>isis sid-ingress-stats)
[Tree] (clear>router>ospf sid-ingress-stats)
Full Context
clear router isis sid-ingress-stats
clear router ospf sid-ingress-stats
Description
This command clears the IS-IS or OSPF ingress SID statistics.
Parameters
- adj
-
Clears the ingress statistics of the adjacency SID specified by the corresponding interface name. Clears all adjacency SIDs ingress statistics if no adjacency SID is specified.
- interface-name
-
Clears the SID ingress statistics for the interface specified by this interface name up to 32 characters.
- adj-set
-
Clears the ingress statistics of the adjacency set specified by the corresponding ID. Clears all adjacency sets ingress statistics if no adjacency set is specified.
- id
-
Clears the SID ingress statistics for the identifier specified for this adjacency set.
- all
-
Clears all the SID ingress statistics.
- node
-
Clears the ingress statistics for the node SID specified by the corresponding prefix. Clears all node SIDs ingress statistics if no node SID is specified.
- ip-prefix[/prefix-length]
-
Clears the IP prefix and prefix length of the node SID.
Platforms
All
sid-ingress-stats
Syntax
sid-ingress-stats adj [interface-name]
sid-ingress-stats all
sid-ingress-stats node [ip-prefix[/ prefix-length]]
Context
[Tree] (clear>router>ospf3 sid-ingress-stats)
Full Context
clear router ospf3 sid-ingress-stats
Description
This command clears the OSPF3 ingress SID statistics.
Parameters
- adj
-
Clears the ingress statistics of the adjacency SID specified by the corresponding interface name. Clears all adjacency SIDs ingress statistics if no adjacency SID is specified.
- interface-name
-
Clears the SID ingress statistics for the interface specified by this interface name up to 32 characters.
- all
-
Clears all the SID ingress statistics.
- node
-
Clears the ingress statistics for the node SID specified by the corresponding prefix. Clears all node SIDs ingress statistics if no node SID is specified.
- ip-prefix[/prefix-length]
-
Clears the IP prefix and prefix length of the node SID.
Platforms
All
sid-stats
sid-stats
Syntax
sid-stats adj [interface-name]
sid-stats adj-set [id]
sid-stats node [ip-prefix[/ prefix-length]] [algo algo-id]
sid-stats summary
Context
[Tree] (show>router>ospf sid-stats)
[Tree] (show>router>isis sid-stats)
Full Context
show router ospf sid-stats
show router isis sid-stats
Description
This command displays information about IGP SIDs statistics.
Parameters
- interface-name
-
Displays only the SID statistics identified by this interface name up to 32 characters.
- id
-
Displays the adjacency set ID.
- ip-prefix[/prefix-length]
-
Displays information for the specified IP prefix and prefix length.
- algo-id
-
Displays the algorithm identifier.
- adj
-
Displays the ingress and egress statistics, if any, of the adjacency SID specified by the corresponding interface name. Displays statistics for all adjacency SIDs if none is specified.
- adj-set
-
Displays the ingress and egress statistics, if any, of the adjacency set specified by its associated ID. Displays statistics for all adjacency sets if none is specified.
- node
-
Displays the ingress and egress statistics, if any, of the node SID specified by the corresponding prefix. Displays statistics for all node SIDs if none is specified.
- algo
-
Displays statistics for the specified algorithm identifier.
- summary
-
Displays statistics indices usage for SID statistics.
Platforms
All
Output
The following outputs are examples of SID statistics information and SID Statistics Adjacency Set Output Fields describes the output fields.
Output ExampleThe show router ospf sid-stats adj command displays statistics for adjacency SIDs.
===============================================================================
Label : 20001 Type : adjacency
Prefix : 10.1.2.2/32
Interface : to_Dut-B
Ingress Oper State: enabled Egress Oper State : enabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
...
===============================================================================
The show router ospf sid-stats adj-set command displays statistics for adjacency set SIDs.
===============================================================================
Label : 20001 Type : adjacencySet
Prefix : 2.1.20.10/32
Adjacency-set : 23
Ingress Oper State: enabled Egress Oper State : enabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
...
===============================================================================
The show router ospf sid-stats node command displays statistics for the specified algorithm.
*A:Dut-C# show router ospf sid-stats node algo 128
===============================================================================
Rtr Base OSPFv2 Instance 0 Sid Statistics
===============================================================================
Ingress Label : 101282 Type : node
Prefix : 10.20.1.2/32
Algorithm : 128
Ingress Oper State: disabled Egress Oper State : disabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
Ingress Label : 101283 Type : node
Prefix : 10.20.1.3/32
Algorithm : 128
Ingress Oper State: disabled Egress Oper State : disabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
Ingress Label : 101285 Type : node
Prefix : 10.20.1.5/32
Algorithm : 128
Ingress Oper State: disabled Egress Oper State : disabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
-------------------------------------------------------------------------------
Sid count : 3
===============================================================================
*A:Dut-C#
The show router ospf sid-stats node command displays statistics for node SIDs.
===============================================================================
Label : 20001 Type : node
Prefix : 1.1.1.1/32
Ingress Oper State: enabled Egress Oper State : enabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
...
===============================================================================
The show router ospf sid-stats summary command displays summary statistics for SIDs.
===============================================================================
Rtr Base OSPFv2 Instance 0 Sid Statistics (summary)
===============================================================================
===============================================================================
SID Statistics summary
===============================================================================
Node Adj Adj-Set
-------------------------------------------------------------------------------
SID Ingress Statistics indexes : 0/0 0/0 0/0
SID Egress Statistics indexes : 0/0 0/0 0/0
-------------------------------------------------------------------------------
<stats>/<sids> : <stats> = number of statistics indexes of specified type
<sids> = total number of SIDs of specified type for which the
statistic is applicable
===============================================================================
Label |
Description |
---|---|
Label |
The ILM MPLS label corresponding to the SID. |
Type |
The type of the SID. |
Prefix |
The prefix corresponding to the node SID, or the IP address of the neighbor (adjacency SID) or the destination IP associated to the adjacency set. |
Interface |
The OSPF interface. |
Ingress Oper State |
Indicates if ingress statistics are enabled or disabled, or if no statistics index is allocated to that SID (no resources). |
Egress Oper State |
Indicates if egress statistics are enabled or disabled, or if no statistics index is allocated to that SID (no resources). |
Ingress Octets |
The number of octets received on ingress for that SID. |
Egress Octets |
The number of octets sent on egress for that SID. |
Ingress Packets |
The number of packets received on ingress for that SID. |
Egress Packets |
The number of packets sent on egress for that SID. |
sid-stats
Syntax
sid-stats adj [interface-name]
sid-stats node [ip-prefix[/ prefix-length]]
sid-stats summary
Context
[Tree] (show>router>ospf3 sid-stats)
Full Context
show router ospf3 sid-stats
Description
This command displays information about IGP SIDs statistics.
Parameters
- adj
-
Displays the ingress and egress statistics, if any, of the adjacency SID specified by the corresponding interface name. Displays statistics for all adjacency SIDs if none is specified.
- interface-name
-
Displays only the SID statistics identified by this interface name up to 32 characters.
- node
-
Displays the ingress and egress statistics, if any, of the node SID specified by the corresponding prefix. Displays statistics for all node SIDs if none is specified.
- ip-prefix[/prefix-length]
-
Displays information for the specified IP prefix and prefix length.
- summary
-
Displays stat indices usage for SID statistics.
Platforms
All
Output
The following outputs are an example of SID statistics information
Output ExampleThe show router ospf3 sid-stats adj command displays statistics for adjacency SIDs.
===============================================================================
Label : 20001 Type : adjacency
Prefix : 10.1.2.2/32
Interface : to_Dut-B
Ingress Oper State: enabled Egress Oper State : enabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
...
===============================================================================
The show router ospf3 sid-stats node command displays statistics for node SIDs.
===============================================================================
Label : 20001 Type : node
Prefix : 1.1.1.1/32
Ingress Oper State: enabled Egress Oper State : enabled
Ingress Octets : 0 Egress Octets : 0
Ingress Packets : 0 Egress Packets : 0
...
===============================================================================
The show router ospf3 sid-stats summary command displays summary statistics for SIDs.
===============================================================================
Rtr Base OSPFv3 Instance 0 Sid Statistics (summary)
===============================================================================
===============================================================================
SID Statistics summary
===============================================================================
Node Adj
-------------------------------------------------------------------------------
SID Ingress Statistics indexes : 0/0 0/0
SID Egress Statistics indexes : 0/0 0/0
-------------------------------------------------------------------------------
<stats>/<sids> : <stats> = number of statistics indexes of specified type
<sids> = total number of SIDs of specified type for which the
statistic is applicable
===============================================================================
site
site
Syntax
site [detail]
site name
Context
[Tree] (show>service>id site)
Full Context
show service id site
Description
This command displays site-specific information for the service.
Parameters
- name
-
Specifies the site name, up to 32 characters in length.
Platforms
All
site
Syntax
site name
Context
[Tree] (clear>service>id site)
Full Context
clear service id site
Description
This command clears site-specific information for the service.
Parameters
- name
-
Clears information about the specified service name, up to 32 characters.
Platforms
All
site-using
site-using
Syntax
site-using [site-name name] [site-id site-id]
Context
[Tree] (show>service site-using)
Full Context
show service site-using
Description
This command displays BGP multihoming sites used by services.
Parameters
- name
-
Specifies the BGP multihoming site name, up to 32 characters.
- site-id
-
Specifies the BGP multihoming site ID.
Platforms
All
sla-profile
sla-profile
Syntax
sla-profile [sla-profile-name [association]]
Context
[Tree] (show subscr-mgmt sla-profile)
Full Context
show subscriber-mgmt sla-profile
Description
This command displays SLA profile information.
Parameters
- sla-profile-name
-
Specifies an existing SLA profile name.
- association
-
Displays the association information configured with the specified sla-profile-name.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber management SLA profile information.
Output Example# show subscriber-mgmt sla-profile "sla-profile-1"
===============================================================================
SLA Profile sla-profile-1
===============================================================================
Description : (Not Specified)
Control plane(s) : local
Host Limits : overall 1
ipv4-overall 1
ipv4-arp 1
ipv4-dhcp 1
ipv4-ppp 1
ipv6-overall 1
ipv6-pd-overall 1
ipv6-pd-ipoe-dhcp 1
ipv6-pd-ppp-dhcp 1
ipv6-wan-overall 1
ipv6-wan-ipoe-dhcp 1
ipv6-wan-ipoe-slaac 1
ipv6-wan-ppp-dhcp 1
ipv6-wan-ppp-slaac 1
lac-overall 1
remove-oldest
Session Limits : ipoe 1
pppoe-local 1
pppoe-lac 1
pppoe-overall 1
l2tp-lns 1
l2tp-lts 1
l2tp-overall 1
overall 1
Egr Sched-Policy : N/A
Ingress Qos-Policy : 1 Egress Qos-Policy : 1
Ingress Queuing Type : Service-queuing (Not Applicable to Policer)
Ingr IP Fltr-Id : N/A Egr IP Fltr-Id : N/A
Ingr IPv6 Fltr-Id : N/A Egr IPv6 Fltr-Id : N/A
Ingress Report-Rate : Maximum
Egress Report-Rate : Maximum
Egress Remarking : from Sap Qos
Credit Control Pol. : N/A
Category Map : (Not Specified)
Use ing L2TP DSCP : false
Default SPI sharing : per-sap
Hs-Agg-Rate-Limit : Maximum
Egress HS Q stat mode: no-override
Bonding Rate-thresh. : high 90 low 80
Bonding Weight : weight 100 5
Last Mgmt Change : 09/30/2020 15:22:30
===============================================================================
-------------------------------------------------------------------------------
Ingress Queue Overrides
-------------------------------------------------------------------------------
Queue Rate CIR HiPrio CBS MBS AvgOvrHd StatMode
-------------------------------------------------------------------------------
No ingress overrides configured.
-------------------------------------------------------------------------------
Egress Queue Overrides
-------------------------------------------------------------------------------
Queue Rate CIR HiPrio CBS MBS AvgOvrHd StatMode
HsClssWght HsWrrWght HsWredQueuePol
-------------------------------------------------------------------------------
No egress overrides configured.
-------------------------------------------------------------------------------
Ingress Policer Overrides
-------------------------------------------------------------------------------
Plcr Rate CIR CBS MBS ByteOffset StatMode
-------------------------------------------------------------------------------
No ingress overrides configured.
-------------------------------------------------------------------------------
Egress Policer Overrides
-------------------------------------------------------------------------------
Plcr Rate CIR CBS MBS ByteOffset StatMode
-------------------------------------------------------------------------------
No egress overrides configured.
-------------------------------------------------------------------------------
QoS statistics aggregation
-------------------------------------------------------------------------------
Ingress policers: all
Ingress queues : all
Egress policers : all
Egress queues : all
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Egress HS WRR Group Overrides
-------------------------------------------------------------------------------
WrrGroupId ClassWeight Rate
-------------------------------------------------------------------------------
No egress overrides configured.
===============================================================================
# show subscriber-mgmt sla-profile
===============================================================================
SLA Profiles
===============================================================================
Name Description
-------------------------------------------------------------------------------
sla_default
sla_prof100_VOIP
sla_prof110_VOIP
sla_prof120_VOIP
sla_prof130_VOIP
sla_prof140_VOIP
sla_prof230_VOIP
sla_prof80
sla_prof80_VOIP
sla_prof81_VOIP
sla_prof90_VOIP
sla_profPC1
sla_profPC2
sla_profPC3
-------------------------------------------------------------------------------
Number of SLA Profiles : 14
===============================================================================
A:Dut-A#
# show subscriber-mgmt sla-profile sla_prof100_VOIP association
===============================================================================
SLA Profile sla_prof100_VOIP
-------------------------------------------------------------------------------
SAP Default-Profile Associations
-------------------------------------------------------------------------------
No associations found.
-------------------------------------------------------------------------------
SAP Static Host Associations
-------------------------------------------------------------------------------
No associations found.
-------------------------------------------------------------------------------
SAP Non-Sub-Traffic-Profile Associations
-------------------------------------------------------------------------------
No associations found.
-------------------------------------------------------------------------------
Sub-Ident-Policy Profile Map Associations
-------------------------------------------------------------------------------
Policy-name : sub_ident_all
- Key : sla_prof100_VOIP
-------------------------------------------------------------------------------
Sub-Profile Map Associations
-------------------------------------------------------------------------------
No associations found.
-------------------------------------------------------------------------------
Explicit Subscriber Map Associations
-------------------------------------------------------------------------------
No associations found.
===============================================================================
A:Dut-A#
SLA Profile Field Descriptions describes subscriber management SLA profile output fields.
Field |
Description |
---|---|
Name |
The Service Level Agreement (SLA) profile name |
Description |
The user provided description of this policy |
Number of SLA Profiles |
The total number of SLA profiles configured on this node |
Control plane(s) |
The SLA profile controlled by local control plane or CUPS control plane |
Host Limits |
The configured maximum number of hosts per SLA profile instance |
Session Limits |
The configured maximum number of sessions per SLA profile instance |
Ingress Qos-Policy |
The ingress QoS policy ID |
Egress Qos-Policy |
The egress QoS policy ID |
Ingress Queuing Type |
The queuing type |
Ingress Filter-Id |
The ingress IP filter |
Egress Filter-Id |
The egress IP filter |
Last Mgmt Change |
The time and date of the most recent management-initiated change |
Queue |
The ingress queue ID |
Rate |
The SLA profile queue rate |
CIR |
The CIR rate |
HiPrio |
The number of high priority packets as determined by the SLA profile ingress QoS policy |
CBS |
The amount of reserved buffer space (in bytes) for the policer |
MBS |
The amount of buffer space (in bytes) allowed for the policer |
slaac
slaac
Syntax
slaac
Context
[Tree] (clear>service>id slaac)
Full Context
clear service id slaac
Description
Commands in this context clear Stateless Address Auto-Configuration (SLAAC) related data for the service.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
slaac
Syntax
slaac
Context
[Tree] (show>service>id slaac)
Full Context
show service id slaac
Description
This command displays SLAAC information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
slm
slm
Syntax
slm lmm [interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor>oam-pm>session slm)
Full Context
monitor oam-pm session slm
Description
This command monitors the Ethernet Synthetic Loss Measurement (SLM) statistics for the specified test's raw measurement interval.
Parameters
- seconds
-
Specifies the time interval, in seconds.
- repeat
-
Specifies the number of times the command is repeated.
- absolute
-
Specifies that the raw statistics are displayed, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Specifies that the rate-per-second is displayed.
Platforms
All
slm
Syntax
slm
Context
[Tree] (show>oam-pm>stats>session slm)
Full Context
show oam-pm statistics session slm
Description
This command selects the session's Ethernet SLM test for the statistical display.
Platforms
All
slope-policy
slope-policy
Syntax
slope-policy [slope-policy-name] [detail]
Context
[Tree] (show>qos slope-policy)
Full Context
show qos slope-policy
Description
This command displays slope policy information.
Parameters
- slope-policy-name
-
The name of the slope policy.
- detail
-
Displays detailed information about the slope policy.
Platforms
All
Output
The following output is an example of slope QoS policy information, and Show QoS Slope Policy Output Fields describes slope QoS policy output fields.
Output Example*A:PE# show qos slope-policy "slope1"
===============================================================================
QoS Slope Policy
===============================================================================
Policy : slope1
Description : (Not Specified)
Time Avg : 7
-------------------------------------------------------------------------------
HighPlus Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 75 Admin State : Enabled
Max Avg : 100 Max Prob. : 100
-------------------------------------------------------------------------------
High Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 50 Admin State : Enabled
Max Avg : 65 Max Prob. : 100
-------------------------------------------------------------------------------
Low Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 30 Admin State : Enabled
Max Avg : 40 Max Prob. : 100
-------------------------------------------------------------------------------
Exceed Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 10 Admin State : Enabled
Max Avg : 25 Max Prob. : 100
===============================================================================
*A:PE#
*A:PE# show qos slope-policy "slope1" detail
===============================================================================
QoS Slope Policy
===============================================================================
Policy : slope1
Description : (Not Specified)
Time Avg : 7
-------------------------------------------------------------------------------
HighPlus Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 75 Admin State : Enabled
Max Avg : 100 Max Prob. : 100
-------------------------------------------------------------------------------
High Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 50 Admin State : Enabled
Max Avg : 65 Max Prob. : 100
-------------------------------------------------------------------------------
Low Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 30 Admin State : Enabled
Max Avg : 40 Max Prob. : 100
-------------------------------------------------------------------------------
Exceed Slope Parameters
-------------------------------------------------------------------------------
Start Avg : 10 Admin State : Enabled
Max Avg : 25 Max Prob. : 100
-------------------------------------------------------------------------------
Associations
-------------------------------------------------------------------------------
Object Type Object Id Application Pool
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
WRED Slot/FP Associations
-------------------------------------------------------------------------------
Slot FP
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
WRED SAP Queue Associations
-------------------------------------------------------------------------------
Policy-Id Queue-Id
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
WRED QoS Queue-Group Associations
-------------------------------------------------------------------------------
Queue-Group Queue-Id
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
*A:PE#
Label |
Description |
---|---|
Policy |
The ID that uniquely identifies the policy. |
Description |
A string that identifies the policy context in the configuration file. |
Time Avg |
The weighting between the previous shared buffer average utilization result and the new shared buffer utilization. |
Slope Parameters |
|
Start Avg |
Specifies the RED slope position for the shared buffer average utilization value where the packet discard probability starts to increase above zero. |
Max Avg |
Specifies the percentage of the shared buffer space for the buffer pool at which point the drop probability becomes one, expressed as a decimal integer. |
Admin State |
Enabled The administrative status of the RED slope is enabled. Disabled The administrative status of the RED slope is disabled. |
Max Prob. |
Specifies the RED slope position for the maximum non-one packet discard probability value before the packet discard probability rises directly to one. |
smet
smet
Syntax
smet [hunt | detail] [rd rd] [community comm-id] [tag tag] [next-hop next-hop] [aspath-regex reg-exp] [originator-ip ip-address | ipv6-address]
Context
[Tree] (show>router>bgp>routes>evpn smet)
Full Context
show router bgp routes evpn smet
Description
This command displays BGP-EVPN SMET routes.
Parameters
- hunt
-
Displays entries for the specified route.
- detail
-
Displays detailed information.
- rd
-
Displays information for the route distinguisher.
- comm-id
-
Specifies the community ID, up to 72 characters.
- tag
-
Specifies the SMET route tag.
- next-hop
-
Specifies the IPv4 or IPv6 BGP next-hop address.
- reg-exp
-
Displays routes matching the specified regular expression, up to 80 characters.
- ip-address | ipv6-address
-
Specifies the originator IPv4 or IPv6 address, up to 64 characters.
Platforms
All
snippets
snippets
Syntax
snippets [detail]
snippets name snippet-name [instance snippet-instance] [detail]
Context
[Tree] (show>service>dynsvc>script snippets)
Full Context
show service dynamic-services script snippets
Description
This command displays the dynamic services snippets information. A snippet is the name of a set of Python functions to create, modify or destroy configuration; for example: a snippet called 'vprn' to create, modify, or destroy VPRN services.
The CLI output generated by a single dynamic service python function call is a snippet instance.
This command is not available in the MD-CLI.
Parameters
- detail
-
Displays dynamic services snippet information.
- snippet-name
-
Specifies the snippet name.
- snippet-instance
-
Specifies the snippet instance.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of dynamic service snippets.
Output Example# show service dynamic-services script snippets
===============================================================================
Dynamic Services Snippets
===============================================================================
Name Instance Ref-count Dict-len
-------------------------------------------------------------------------------
vprn VRF-1 1 75
vprn_1 1/1/1:1.901 0 190
-------------------------------------------------------------------------------
No. of Snippets: 2
===============================================================================
# show service dynamic-services script snippets detail
===============================================================================
Dynamic Service Snippets
===============================================================================
Snippet : vprn:VRF-1
-------------------------------------------------------------------------------
reference-count : 1
dictionary-length : 75
Root-object
-----------
oid : svcRowStatus.100000
Reserved-id
-----------
id : service-id:100000
-------------------------------------------------------------------------------
Snippet : vprn_1:1/1/1:1.901
-------------------------------------------------------------------------------
reference-count : 0
dictionary-length : 190
Referenced-snippet
------------------
snippet : vprn:VRF-1
-------------------------------------------------------------------------------
No. of Snippets: 2
===============================================================================
Snippets Field Descriptions describes snippets fields.
Output field |
Description |
---|---|
Name |
The snippet name. |
Instance |
The snippet instance. |
Ref-count reference-count |
The number of times this snippet is referenced by other snippets. |
Dict-len dictionary-length |
The length of the python dictionary stored for this snippet. |
Root-object |
The object created by a Dynamic Service of which the parent is not created by a Dynamic Service. |
snmp
snmp
Syntax
snmp
Context
[Tree] (show snmp)
Full Context
show snmp
Description
Commands in this context display SNMP configuration.
Platforms
All
snmp
Syntax
snmp
Context
[Tree] (show>system>security snmp)
Full Context
show system security snmp
Description
Commands in this context show SNMP information.
Platforms
All
snmp-trap-group
snmp-trap-group
Syntax
snmp-trap-group [log-id]
Context
[Tree] (show>service>id>log snmp-trap-group)
Full Context
show service id log snmp-trap-group
Description
This command displays SNMP trap group configuration information.
Parameters
- log-id
-
Displays only SNMP trap group information for the specified trap group log ID.
Platforms
All
Output
SNMP Trap Group Output
SNMP Trap Group Field Descriptions describes SNMP trap group output fields.
Label |
Description |
---|---|
Log-ID |
The log destination ID for an event stream. |
Address |
The IP address of the trap receiver. |
Port |
The destination UDP port used for sending traps to the destination, expressed as a decimal integer. |
Version |
Specifies the SNMP version format to use for traps sent to the trap receiver. Valid values are snmpv1, snmpv2c, snmpv3. |
Community |
The community string required by snmpv1 or snmpv2c trap receivers. |
Security-Level |
The required authentication and privacy levels required to access the views on this node. |
Replay |
Indicates whether or not the replay parameter has been configured, enabled or disabled, for the trap-target address. |
Replay from |
Indicates the sequence ID of the first missed notification that will be replayed when a route is added to the routing table by which trap-target address can be reached. If no notifications are waiting to be replayed this field shows n/a. |
Last Replay |
Indicates the last time missed events were replayed to the trap-target address. If no events have ever been replayed this field shows never. |
snmp-trap-group
Syntax
snmp-trap-group [log-id-or-log-name]
Context
[Tree] (show>log snmp-trap-group)
Full Context
show log snmp-trap-group
Description
This command displays SNMP trap group configuration information.
Parameters
- log-id-or-log-name
-
Displays only SNMP trap group information for the specified trap group log ID, up to 64 characters.
Platforms
All
Output
The following output is an example of SNMP trap group information.
SNMP Trap Group Output Fields describes SNMP trap group output fields.
Output ExampleA:SetupCLI>config>log>snmp-trap-group# show log snmp-trap-group 44
===============================================================================
SNMP Trap Group 44
===============================================================================
Description : none
-------------------------------------------------------------------------------
Name : ntt-test
Address : 10.10.10.3
Port : 162
Version : v2c
Community : ntttesting
Sec. Level : none
Replay : disabled
Replay from : n/a
Last replay : never
-------------------------------------------------------------------------------
Name : test2
Address : 10.20.20.5
Port : 162
Version : v2c
Community : ntttesting
Sec. Level : none
Replay : disabled
Replay from : n/a
Last replay : never
===============================================================================
A:SetupCLI>config>log>snmp-trap-group#
Label |
Description |
---|---|
Log-ID/Name |
The log destination ID or name for an event stream. |
Address |
The IP address of the trap receiver, |
Port |
The destination UDP port used for sending traps to the destination, expressed as a decimal integer. |
Version |
Specifies the SNMP version format to use for traps sent to the trap receiver. Valid values are snmpv1, snmpv2c, snmpv3. |
Community |
The community string required by snmpv1 or snmpv2c trap receivers. |
Security-Level |
The required authentication and privacy levels required to access the views on this node. |
Replay |
Indicates whether or not the replay parameter has been configured, enabled or disabled, for the trap-target address. |
Replay from |
Indicates the sequence ID of the first missed notification that will be replayed when a route is added to the routing table by which trap-target address can be reached. If no notifications are waiting to be replayed this field shows n/a. |
Last Replay |
Indicates the last time missed events were replayed to the trap-target address. If no events have ever been replayed this field shows never. |
sntp
sntp
Syntax
sntp
Context
[Tree] (show>system sntp)
Full Context
show system sntp
Description
This command displays SNTP protocol configuration and state.
Platforms
All
Output
The following output is an example of SNTP information, and System SNTP Field Descriptions describes the output fields.
Output ExampleA:ALA-1# show system sntp
===============================================================================
SNTP
===============================================================================
SNTP Server Version Preference Interval
-------------------------------------------------------------------------------
10.10.20.253 3 Preferred 64
===============================================================================
A:ALA-1#
Label |
Description |
---|---|
SNTP Server |
The SNTP server address for SNTP unicast client mode. |
Version |
The SNTP version number, expressed as an integer. |
Preference |
Normal — When more than one time server is configured, one server can be configured to have preference over another. Preferred — Indicates that this server has preference over another. |
Interval |
The frequency, in seconds, that the server is queried. |
sockets
sockets
Syntax
sockets
Context
[Tree] (tools>dump>router>ldp sockets)
Full Context
tools dump router ldp sockets
Description
This command dumps information for all LDP sockets.
Platforms
All
software-repository
software-repository
Syntax
software-repository [repository-name]
Context
[Tree] (show>system software-repository)
Full Context
show system software-repository
Description
This command displays software repository information.
Parameters
- repository-name
-
Specifies the software repository name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
source
source
Syntax
source [ip-address/mask] [type {configured | dynamic | both}] [detail]
Context
[Tree] (show>router>msdp source)
Full Context
show router msdp source
Description
This command displays the discovery method for this multicast source.
Parameters
- configured
-
Displays user-created sources.
- dynamic
-
Displays dynamically created sources.
- both
-
Displays both user-configured and dynamically created sources.
- detail
-
Displays detailed MSDP source information.
Platforms
All
source-active
source-active
Syntax
source-active [{group ip-address | local | originator ip-address | peer ip-address | source ip-address | group ip-address source ip-address}] [detail]
Context
[Tree] (show>router>msdp source-active)
Full Context
show router msdp source-active
Description
This command displays source active messages accepted by MSDP.
Parameters
- group ip-address
-
Displays information about the specified group IP address.
- local
-
Displays information about local source-active messages.
- originator ip-address
-
Displays information about the specified originator IP address.
- peer ip-address
-
Displays information about the specified peer IP address.
- source ip-address
-
Displays information about the specified source IP address.
- group ip-address
-
Displays information about the specified group IP address.
- detail
-
Displays detailed MSDP source-active information.
Platforms
All
Output
The following output is an example of MSDP source active information. MSDP Source-Active Fields provides MSDP source active field descriptions.
Output ExampleA:ALA-48# show router msdp source-active
===============================================================================
MSDP Source Active Info
===============================================================================
Grp Address Src Address Origin RP Peer Address State Timer
-------------------------------------------------------------------------------
239.100.0.0 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.1 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.2 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.3 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.4 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.5 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.6 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.7 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.8 10.112.1.2 10.20.1.1 10.20.1.1 69
239.100.0.9 10.112.1.2 10.20.1.1 10.20.1.1 69
-------------------------------------------------------------------------------
MSDP Source Active : 10
===============================================================================
A:ALA-48#
A:ALA-48# show router msdp source-active detail
===============================================================================
MSDP Source Active
===============================================================================
Group Address : 239.100.0.0 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 3d 01:44:25
Group Address : 239.100.0.1 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.2 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.3 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.4 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.5 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.7 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.8 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
Group Address : 239.100.0.9 Source Address : 10.112.1.2
Origin RP : 10.20.1.1 Peer Address : 10.20.1.1
State Timer : 64 Up Time : 48d 18:22:29
-------------------------------------------------------------------------------
MSDP Source Active : 10
===============================================================================
A:ALA-48#
Label |
Description |
---|---|
Grp Address |
The IP address of the group. |
Src Address |
The IP address of the source. |
Origin RP |
The origination rendezvous point (RP) address. |
Peer Address |
The address of the peer. |
State Timer |
The time-out value. If the value reaches zero, the SA is removed. |
source-active-rejected
source-active-rejected
Syntax
source-active-rejected [peer-group name] [ group ip-address] [source ip-address] [originator ip-address] [peer ip-address]
Context
[Tree] (show>router>msdp source-active-rejected)
Full Context
show router msdp source-active-rejected
Description
This command displays source-active messages rejected by MSDP.
Parameters
- peer-group name
-
Displays information about rejected source-active messages for the specified peer group.
- group ip-address
-
Displays information about the specified group IP address.
- source ip-address
-
Displays information about the source address of the source active entry that is rejected.
- originator ip-address
-
Displays information about the specified originator IP address.
- peer ip-address
-
Displays information about the peer from which this rejected source active entry was last received.
Platforms
All
Output
The following output is an example of MSDP rejected source active information. MSDP Source-Active Fields provides MSDP source active field descriptions.
Output Example*A:ALA-48# show router msdp source-active-rejected
===============================================================================
MSDP Source Active Rejected Info
===============================================================================
Grp Address Src Address Origin RP Peer Address Reject Reason
-------------------------------------------------------------------------------
239.100.0.1 10.0.0.1 10.20.0.1 239.0.0.1 Import Policy
239.100.0.2 10.0.0.2 10.20.0.2 239.0.0.2 Export Policy
239.100.0.3 10.0.0.3 10.20.0.3 239.0.0.3 RPF Failure
239.100.0.4 10.0.0.4 10.20.0.4 239.0.0.4 Limit Exceeded
239.100.0.5 10.0.0.5 10.20.0.5 239.0.0.5 Limit Exceeded
239.100.0.6 10.0.0.6 10.20.0.6 239.0.0.6 Limit Exceeded
239.100.0.7 10.0.0.7 10.20.0.7 239.0.0.7 Limit Exceeded
-------------------------------------------------------------------------------
SA Rejected Entries : 7
===============================================================================
*A:ALA-48#
Label |
Description |
---|---|
Grp Address |
The IP address of the group. |
Src Address |
The IP address of the source. |
Origin RP |
The origination rendezvous point (RP) address. |
Peer Address |
The address of the peer. |
Reject Reason |
The reason why this source active entry is rejected. |
source-address
source-address
Syntax
source-address
Context
[Tree] (show>system>security source-address)
Full Context
show system security source-address
Description
This command displays source-address configured for applications.
Platforms
All
Output
The following output is an example of source address output information.
Show Source Address Output Fields describes source address output fields.
Output ExampleA:SR-7# show system security source-address
===============================================================================
Source-Address applications
===============================================================================
Application IP address/Interface Name Oper status
-------------------------------------------------------------------------------
telnet 10.20.1.7 Up
radius loopback1 Up
===============================================================================
A:SR-7#
Label |
Description |
---|---|
Application |
Displays the source-address application. |
IP address Interface Name |
Displays the source address IP address or interface name. |
Oper status |
Up: The source address is operationally up. Down: The source address is operationally down. |
spb
spb
Syntax
spb
Context
[Tree] (clear>service>id spb)
Full Context
clear service id spb
Description
This command clears SPB related data.
Platforms
All
spb
Syntax
spb
Context
[Tree] (show>service>id spb)
Full Context
show service id spb
Description
Commands in this context display SPB related information.
Platforms
All
spf
spf
Syntax
spf
Context
[Tree] (show>service>id>spb spf)
Full Context
show service id spb spf
Description
This command displays SPF information.
Platforms
All
Output
The following output is an example of service SPB SPF information.
Output ExampleA:cses-B01# show service id spb spf
===============================================================================
Path Table
===============================================================================
Node Interface Nexthop
-------------------------------------------------------------------------------
Fwd Tree: unicast, ECT Alg: low-path-id
-------------------------------------------------------------------------------
cses-B07.00 sap:1/1/20:500 cses-B07
cses-B01.00 sap:1/1/20:500 cses-B07
cses-B07.00 sap:1/1/20:500 cses-B07
Fwd Tree: unicast, ECT Alg: high-path-id
-------------------------------------------------------------------------------
cses-B07.00 sap:1/1/20:500 cses-B07
cses-B01.00 sap:1/1/20:500 cses-B07
cses-B07.00 sap:1/1/20:500 cses-B07
Fwd Tree: multicast, ECT Alg: low-path-id
-------------------------------------------------------------------------------
cses-B07.00 sap:1/1/20:500 cses-B07
cses-B01.00 sap:1/1/20:500 cses-B07
cses-B07.00 sap:1/1/20:500 cses-B07
Fwd Tree: multicast, ECT Alg: high-path-id
-------------------------------------------------------------------------------
cses-B07.00 sap:1/1/20:500 cses-B07
cses-B01.00 sap:1/1/20:500 cses-B07
cses-B07.00 sap:1/1/20:500 cses-B07
===============================================================================
spf
Syntax
spf [lfa]
Context
[Tree] (show>router>ospf spf)
[Tree] (show>router>ospf3 spf)
Full Context
show router ospf spf
show router ospf3 spf
Description
This command displays statistics of shortest-path-first (SPF) calculations.
Parameters
- lfa
-
Displays Loop-Free Alternate (LFA) next-hop information.
Platforms
All
Output
SPF Output Fields
SPF Output Fields describes SPF output fields.
Label |
Description |
---|---|
Total SPF Runs |
The total number of SPF runs triggered by new or updated LSAs. |
Last Full SPF run @ |
The date and time when the last full SPF was run. |
Last Full SPF Time |
The duration, in seconds, of the last full SPF calculation. Last Full SPF Time = Intra SPF Time + Inter SPF Time + Extern SPF Time + RTM Updt Time. |
Intra SPF Time |
The duration, in seconds, of the Intra-area phase of the last SPF calculation. |
Inter SPF Time |
The duration, in seconds, of the Inter-area phase of the last SPF calculation. |
Extern SPF Time |
The duration, in seconds, of the External phase of the last SPF calculation. |
RTM Updt Time |
The duration, in seconds, of the RTM update phase of the last SPF calculation. |
Min/Avg/Max Full SPF Time |
Min The minimum time, in seconds, used to perform a full SPF calculation. Avg The average time, in seconds, of all the full SPF calculations performed by this OSPF router. Max The maximum time, in seconds, used to perform a full SPF calculation. |
Total Sum Incr SPF Runs |
The total number of incremental SPF runs triggered by new or updated type-3 and type-4 summary LSAs. |
Total Ext Incr SPF Runs |
The total number of incremental SPF runs triggered by new or updated type-5 external LSAs. |
*A:Dut-C# show router ospf spf
===============================================================================
Rtr Base OSPFv2 Instance 0 SPF Statistics
===============================================================================
Total SPF Runs : 6
Last Full SPF run @ : 05/27/2015 08:45:25
Last Full SPF Time : < 0.01 secs
Intra SPF Time : < 0.01 secs
Inter SPF Time : < 0.01 secs
Extern SPF Time : < 0.01 secs
RTM Updt Time : < 0.01 secs
Min/Avg/Max Full SPF Times : 0.00/0.00/0.00 secs
Min/Avg/Max RTM Updt Times : 0.00/0.00/0.00 secs
Total Sum Incr SPF Runs : 9
Last Sum Incr SPF run @ : 05/27/2015 08:36:14
Last Sum Incr Calc Time : < 0.01 secs
Total Ext Incr SPF Runs : 0
===============================================================================
*A:Dut-C# show router ospf spf lfa
===============================================================================
Rtr Base OSPFv2 Instance 0 SPF Statistics
===============================================================================
Total SPF Runs : 6
Last Full SPF run @ : 05/27/2015 08:45:25
Last Full SPF Time : < 0.01 secs
Intra SPF Time : < 0.01 secs
Inter SPF Time : < 0.01 secs
Extern SPF Time : < 0.01 secs
RTM Updt Time : < 0.01 secs
Min/Avg/Max Full SPF Times : 0.00/0.00/0.00 secs
Min/Avg/Max RTM Updt Times : 0.00/0.00/0.00 secs
Total Sum Incr SPF Runs : 9
Last Sum Incr SPF run @ : 05/27/2015 08:36:14
Last Sum Incr Calc Time : < 0.01 secs
Total Ext Incr SPF Runs : 0
Total LFA SPF Runs : 1
Last LFA SPF run @ : 05/27/2015 08:45:25
Last LFA SPF Time : < 0.01 secs
Min/Avg/Max LFA SPF Times : 0.00/0.00/0.00 secs
===============================================================================
A:Dut-A# show router ospf 1 spf lfa
=======================================================================
Rtr Base OSPFv2 Instance 1 SPF Statistics
=======================================================================
Total SPF Runs : 6
Last Full SPF run @ : 02/20/2012 09:19:35
Last Full SPF Time : < 0.01 secs
Intra SPF Time : < 0.01 secs
Inter SPF Time : < 0.01 secs
Extern SPF Time : < 0.01 secs
RTM Updt Time : < 0.01 secs
Min/Avg/Max Full SPF Times : 0.00/0.00/0.00 secs
Min/Avg/Max RTM Updt Times : 0.00/0.00/0.00 secs
Total Sum Incr SPF Runs : 0
Total Ext Incr SPF Runs : 0
Total LFA SPF Runs : 5
Last LFA SPF run @ : 02/20/2012 09:19:35
Last LFA SPF Time : < 0.01 secs
Min/Avg/Max LFA SPF Times : 0.00/0.00/0.00 secs
=======================================================================
A:ALA-A# show router ospf 1 spf
===============================================================================
Rtr Base OSPFv2 Instance 1 SPF Statistics
===============================================================================
Total SPF Runs : 109
Last Full SPF run @ : 11/07/2006 18:43:07
Last Full SPF Time : < 0.01 secs
Intra SPF Time : < 0.01 secs
Inter SPF Time : < 0.01 secs
Extern SPF Time : < 0.01 secs
RTM Updt Time : < 0.01 secs
Min/Avg/Max Full SPF Times : 0.02/0.00/0.06 secs
Min/Avg/Max RTM Updt Times : 0.02/0.00/0.06 secs
Total Sum Incr SPF Runs : 333
Last Sum Incr SPF run @ : 11/07/2006 18:43:09
Last Sum Incr Calc Time : < 0.01 secs
Total Ext Incr SPF Runs : 0
===============================================================================
A:ALA-A#
spf-log
spf-log
Syntax
spf-log
Context
[Tree] (show>service>id>spb spf-log)
Full Context
show service id spb spf-log
Description
This command displays SPF Log information.
Platforms
All
Output
The following output is an example of service SPB SPF log information.
Output ExampleA:cses-B01# show service id spb spf-log
===============================================================================
ISIS SPF Log
===============================================================================
When Duration L1 Nodes L2 Nodes Event Count Type
-------------------------------------------------------------------------------
07/23/2012 16:01:13 <0.01s 1 0 1 Reg
07/23/2012 16:01:19 <0.01s 1 0 4 Reg
07/23/2012 16:01:24 <0.01s 3 0 2 Reg
07/23/2012 16:01:29 <0.01s 4 0 1 Reg
-------------------------------------------------------------------------------
Log Entries : 4
-------------------------------------------------------------------------------
spf-log
Syntax
spf-log [detail]
Context
[Tree] (show>router>isis spf-log)
Full Context
show router isis spf-log
Description
This command displays IS-IS SPF log information.
Parameters
- detail
-
Displays detailed spf-log information.
Platforms
All
Output
The following output is an example of SPF log information.
Output Example*A:Dut-C# show router isis spf-log
===============================================================================
Rtr Base ISIS Instance 0 SPF Log
===============================================================================
When Duration L1 Nodes L2 Nodes Event Count Type
-------------------------------------------------------------------------------
01/26/2015 11:22:19 <0.01s - - - pLfa
01/26/2015 11:22:19 <0.01s - - - rLfa
01/26/2015 11:22:20 <0.01s 4 4 25 Reg
01/26/2015 11:22:20 <0.01s - - - Lfa
01/26/2015 11:22:20 <0.01s - - - rLfa
01/26/2015 11:22:24 <0.01s 4 4 11 Reg
01/26/2015 11:22:24 <0.01s - - - Lfa
01/26/2015 11:22:24 <0.01s - - - rLfa
01/26/2015 11:22:32 <0.01s 4 4 21 Reg
01/26/2015 11:22:32 <0.01s - - - Lfa
01/26/2015 11:22:32 <0.01s - - - rLfa
01/26/2015 11:22:33 <0.01s - - - pSpf
01/26/2015 11:22:33 <0.01s - - - pLfa
01/26/2015 11:22:33 <0.01s - - - rLfa
01/26/2015 11:22:41 <0.01s - - - pSpf
01/26/2015 11:22:41 <0.01s - - - pLfa
01/26/2015 11:22:41 <0.01s - - - rLfa
01/26/2015 11:22:51 <0.01s 4 4 4 Reg
01/26/2015 11:22:51 <0.01s - - - Lfa
01/26/2015 11:22:51 <0.01s - - - rLfa
-------------------------------------------------------------------------------
Log Entries : 20
===============================================================================
*A:Dut-C#
A:SetupCLI# show router isis spf-log detail
===============================================================================
Rtr Base ISIS Instance 0 SPF Log
===============================================================================
When : 10/01/2011 03:40:25 Duration : <0.01s
L1 Nodes : 1 L2 Nodes : 1
Trigger LSP: SetupCLI.00-00 Event Count : 78
SPF Type : Reg
Reason : LSPCONTENT
When : 10/01/2011 03:40:26 Duration : <0.01s
L1 Nodes : 1 L2 Nodes : 1
Trigger LSP: SetupCLI.00-00 Event Count : 1
SPF Type : Reg
Reason : LSPCONTENT
When : 10/01/2011 03:40:25 Duration : <0.01s
L1 Nodes : 1 L2 Nodes : 1
Trigger LSP: SetupCLI.00-00 Event Count : 25
SPF Type : Reg
Reason : NEWAREA NEWREACH LSPCONTENT MANUALREQ
When : 10/01/2011 03:40:27 Duration : <0.01s
L1 Nodes : 1 L2 Nodes : 1
Trigger LSP: SetupCLI.00-00 Event Count : 1
SPF Type : Reg
Reason : LSPCONTENT
When : 10/01/2011 03:40:27 Duration : <0.01s
L1 Nodes : 0 L2 Nodes : 0
Trigger LSP: SetupCLI.00-00 Event Count : 1
SPF Type : Lfa
Reason : LSPCONTENT
When : 10/01/2011 03:40:25 Duration : <0.01s
L1 Nodes : 1 L2 Nodes : 1
Trigger LSP: SetupCLI.00-00 Event Count : 75
SPF Type : Reg
Reason : LSPCONTENT
When : 10/01/2011 03:40:27 Duration : <0.01s
L1 Nodes : 1 L2 Nodes : 1
Trigger LSP: SetupCLI.00-00 Event Count : 1
SPF Type : Reg
Reason : LSPCONTENT
===============================================================================
A:SetupCLI#
IS-IS SPF Log Output Fields describes the IS-IS SPF log output fields.
Label |
Description |
---|---|
When |
Displays the timestamp when the SPF run started on the system. |
Duration |
Displays the time (in hundredths of a second) required to complete the SPF run. |
L1 Nodes |
Displays the number of Level 1 nodes involved in the SPF run. |
L2 Nodes |
Displays the number of Level 2 nodes involved in the SPF run. |
Event Count |
Displays the number of SPF events that triggered the SPF calculation. |
Type |
Displays the SPF type, Reg (regular) or Lfa (loop free alternative). |
Trigger LSP |
Displays the LSP that triggered the SPF run. |
Reason |
Displays the reason(s) for the SPF run. NEWADJ: An adjacency changed. NEWLSP: A new LSP was received. NEWAREA: An area changed. NEWREACH: A prefix changed. ECMPCHANGED: An ECMP path changed. NEWMETRIC: A prefix metric changed. RESTART: The graceful restart exited. LSPEXPIRED: An LSP expired. DBCHANGED: The LSP database was cleared by an administrator. LSPCONTENT: The content of an LSP changed. NEWPREF: The external route preference changed. NEWNLPID: The routed protocols (IPv4 or IPv6) changed. MANUALREQ: An SPF calculation was requested by an administrator. ADMINTAGCHANGED: An administrative tag changed. TUNNELCHANGED: An MPLS tunnel changed. |
spf-log
split-horizon-group
split-horizon-group
Syntax
split-horizon-group [group-name]
Context
[Tree] (show>service>id split-horizon-group)
Full Context
show service id split-horizon-group
Description
This command displays service split horizon groups.
Parameters
- group-name
-
Specifies a group name up to 32 characters.
Platforms
All
Output
The following output is an example of service split horizon group information.
Output ExampleA:ALA-1# show service id 700 split-horizon-group
=============================================================================
Service: Split Horizon Group
=============================================================================
Name Description
-----------------------------------------------------------------------------
R DSL-group1 Split horizon group for DSL
-----------------------------------------------------------------------------
R = Residential Split Horizon Group
No. of Split Horizon Groups: 1
=============================================================================
A:ALA-1#
A:ALA-1# show service id 700 split-horizon-group DSL-group1
===============================================================================
Service: Split Horizon Group
===============================================================================
Name Description
-------------------------------------------------------------------------------
R DSL-group1 Split horizon group for DSL
-------------------------------------------------------------------------------
Associations
-------------------------------------------------------------------------------
SAP 1/1/3:1
SDP 108:1
SDP 109:1
-------------------------------------------------------------------------------
R = Residential Split Horizon Group
SAPs Associated : 1 SDPs Associated : 2
===============================================================================
A:ALA-1#
spmsi-ad
spmsi-ad
Syntax
spmsi-ad [hunt | detail] [rd rd] [community comm-id] [tag tag] [next-hop next-hop] [aspath-regex reg-exp] [originator-ip ip-address | ipv6-address]
Context
[Tree] (show>router>bgp>routes>evpn spmsi-ad)
Full Context
show router bgp routes evpn spmsi-ad
Description
This command displays BGP-EVPN SPMSI AD routes.
Parameters
- hunt
-
Displays entries for the specified route.
- detail
-
Displays detailed information.
- rd
-
Displays information for the route distinguisher.
- comm-id
-
Specifies the community ID, up to 72 characters.
- tag
-
Specifies the SPMSI AD route tag.
- next-hop
-
Specifies the IPv4 or IPv6 BGP next-hop address.
- reg-exp
-
Displays routes matching the specified regular expression, up to 80 characters.
- ip-address | ipv6-address
-
Specifies the originator IPv4 or IPv6 address, up to 64 characters.
Platforms
All
spoke-sdp
spoke-sdp
Syntax
spoke-sdp sdp-id[:vc-id] {all | counters | stp | l2pt | mrp}
Context
[Tree] (clear>service>statistics>id spoke-sdp)
Full Context
clear service statistics id spoke-sdp
Description
This command clears statistics for the spoke SDP bound to the service.
Parameters
- sdp-id
-
The spoke SDP ID for which to clear statistics
- vc-id
-
The virtual circuit ID on the SDP ID to be reset
- all
-
Clears all queue statistics and STP statistics associated with the SDP
- counters
-
Clears all queue statistics associated with the SDP
- stp
-
Clears all STP statistics associated with the SDP
- l2pt
-
Clears all L2PT statistics associated with the SDP
- mrp
-
Clears all MRP statistics associated with the SDP
Platforms
All
spoke-sdp
Syntax
spoke-sdp sdp-id:vc-id ingress-vc-label
spoke-sdp sdp-id:vc-id l2tpv3
spoke-sdp sdp-id:vc-id vccv-bfd {session | statistics}
Context
[Tree] (clear>service>id spoke-sdp)
Full Context
clear service id spoke-sdp
Description
This command clears and resets the spoke SDP bindings for the service.
Parameters
- sdp-id
-
The spoke SDP ID to be reset.
- vc-id
-
The virtual circuit ID on the SDP ID to be reset.
- ingress-vc-label
-
Specifies to clear the ingress VC label.
- l2tpv3
-
Specifies to clear the session mismatch flag on the spoke-SDP binding after the flag was set to true by a detected mismatch between the configured parameters and the received parameters.
- vccv-bfd
-
Specifies to clear the following information related to VCCV BFD on the spoke-sdp.
- session
-
Clears session information.
- statistics
-
Clears spoke SDP statistics.
Platforms
All
spoke-sdp-fec
spoke-sdp-fec
Syntax
spoke-sdp-fec [1 to 4294967295]
Context
[Tree] (show>service>id spoke-sdp-fec)
Full Context
show service id spoke-sdp-fec
Description
This command displays spoke-SDP FEC information.
Parameters
- detail
-
Displays detailed information.
Platforms
All
Output
The following output is an example of spoke-SDP FEC information.
Output Example===============================================================================
Service Spoke-SDP FEC Information
===============================================================================
Spoke-Sdp-Fec-Id : 1 Admin State : enabled
FEC Type : 129 AII Type : 2
Standby Sig Slave : disabled ICB : disabled
Signaling : auto Auto Config : disabled
PW Template Id : (none) Precedence : 4
Retry Timer : 10 secs Retry Count : 10
Retry Timer Remaining: 0 secs Retries Remaining: 0
SAII Type2 : 3:10.20.1.3:1
TAII Type2 : 6:10.20.1.6:1
Path : n/a
Endpoint : n/a
Oper SDP-Bind : 17407:4294967246
Last Error : <none>
===============================================================================
Entries found: 1
===============================================================================
spoke-sdp-fec-using
spoke-sdp-fec-using
Syntax
spoke-sdp-fec-using [spoke-sdp-fec-id spoke-sdp-fec-id] [ saii-type2 global-id:prefix:ac-id] [taii-type2 global-id:prefix:ac-id] [path name] [ expired]
Context
[Tree] (show>service spoke-sdp-fec-using)
Full Context
show service spoke-sdp-fec-using
Description
Displays the SDPs used by spoke-sdp-fecs at this node.
Parameters
- spoke-sdp-fec-id
-
Specifies the spoke-SDP FEC ID for which to show SDP information.
- global-id
-
Specifies the SAII or TAII global ID.
- prefix
-
Specifies the SAII or TAII prefix.
- ac-id
-
Specifies the SAII or TAII AC ID.
- name
-
Specifies the path name. 32 characters maximum.
- expired
-
Displays information for expired SDPs.
Platforms
All
Output
The following output is an example of spoke-SDP information.
Output Example*A:Dut-C# show service spoke-sdp-fec-using
===============================================================================
Service Spoke-SDP-Fec Information
===============================================================================
SvcId SpokeSdpFec Oper-SdpBind SAII-Type2
Path TAII-Type2
-------------------------------------------------------------------------------
1 1 17407:4294967245 3:10.20.1.3:1
n/a 6:10.20.1.6:1
2 2 17407:4294967247 3:10.20.1.3:2
n/a 6:10.20.1.6:2
3 3 17407:4294967248 3:10.20.1.3:3
n/a 6:10.20.1.6:3
4 4 17407:4294967249 3:10.20.1.3:4
n/a 6:10.20.1.6:4
5 5 17407:4294967250 3:10.20.1.3:5
n/a 6:10.20.1.6:5
6 6 17407:4294967251 3:10.20.1.3:6
n/a 6:10.20.1.6:6
7 7 17407:4294967252 3:10.20.1.3:7
n/a 6:10.20.1.6:7
8 8 17407:4294967253 3:10.20.1.3:8
n/a 6:10.20.1.6:8
9 9 17407:4294967254 3:10.20.1.3:9
n/a 6:10.20.1.6:9
10 10 17407:4294967255 3:10.20.1.3:10
n/a 6:10.20.1.6:10
-------------------------------------------------------------------------------
Entries found: 10
squelch-ingress-levels
squelch-ingress-levels
Syntax
squelch-ingress-levels [all | ctag-space] [ sdp-id[:vc-id]]
Context
[Tree] (show>service>sdp-using>eth-cfm squelch-ingress-levels)
Full Context
show service sdp-using eth-cfm squelch-ingress-levels
Description
This command displays the squelch ingress levels associated with SDP bindings.
Parameters
- sdp-id[:vc-id]
-
Specifies the SDP ID and virtual circuit ID on the SDP ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
sr-adj-sets
sr-adj-sets
Syntax
sr-adj-sets [adjacency-set-id] [detail]
Context
[Tree] (show>router>isis sr-adj-sets)
Full Context
show router isis sr-adj-sets
Description
This command displays IS-IS SR adjacency set log information.
Parameters
- adjacency-set-id
-
Displays SR adjacency set ID information.
- detail
-
Displays detailed SR adjacency set information.
Platforms
All
Output
The following output is an example of sr-adj-sets log information.
Output Example*A:Dut-C# show router isis sr-adj-sets
===============================================================================
Rtr Base ISIS Instance 0 Adjacency Sets
===============================================================================
ID State Label Label Members Members Neighbor
Value Type Total Active System Id
-------------------------------------------------------------------------------
1003 active 524285 DL 1 1 0100.2000.1001
1006 active 524284 DL 1 1 0100.2000.1005
1015 active 18448 SL 1 1 0100.2000.1001
1018 active 18451 SL 1 1 0100.2000.1005
1027 active 524283 DL 1 1 0100.2000.1001
1030 active 524282 DL 1 1 0100.2000.1005
1039 active 18460 SL 1 1 0100.2000.1001
1042 active 18463 SL 1 1 0100.2000.1005
1050 active 524281 DL 2 2 none
1056 active 18471 SL 2 2 none
1063 active 524280 DL 1 1 0100.2000.1001
1066 active 524279 DL 1 1 0100.2000.1005
1075 active 18478 SL 1 1 0100.2000.1001
1078 active 18481 SL 1 1 0100.2000.1005
1087 active 524278 DL 1 1 0100.2000.1001
1090 active 524277 DL 1 1 0100.2000.1005
1099 active 18490 SL 1 1 0100.2000.1001
1102 active 18493 SL 1 1 0100.2000.1005
1110 active 524276 DL 2 2 none
1116 active 18501 SL 2 2 none
-------------------------------------------------------------------------------
DL: dynamic local
SL: static local
-------------------------------------------------------------------------------
No. of SR Adjacency Sets: 20
===============================================================================
IS-IS SR Adjacency Set Output Fields describes the IS-IS sr-adj-sets output fields.
Label |
Description |
---|---|
ID |
Displays the ID |
State |
Displays the state (active or inactive) |
Label Value |
Displays the label value |
Label Type |
Displays the label type, Dynamic Local (DL) or Static Local (SL) |
Members Total |
Displays the number of total members |
Members Active |
Displays the number of active members |
Neighbor System Id |
Displays the neighbor system ID |
No. of SR Adjacency Sets |
Displays the number of SR adjacency sets |
sr-adj-sets
Syntax
sr-adj-sets [adjacency-set-id] [detail]
Context
[Tree] (show>router>ospf sr-adj-sets)
Full Context
show router ospf sr-adj-sets
Description
This command displays OSPF SR adjacency set log information.
Parameters
- adjacency-set-id
-
Displays SR adjacency set ID information.
- detail
-
Displays detailed SR adjacency set information.
Platforms
All
Output
The following output is an example of sr-adj-sets log information.
Output Example*A:Dut-C# show router ospf sr-adj-sets
===============================================================================
Rtr Base OSPF Instance 0 Adjacency Sets
===============================================================================
ID State Label Label Members Members Neighbor
Value Type Total Active System Id
-------------------------------------------------------------------------------
1003 active 524285 DL 1 1 0100.2000.1001
1006 active 524284 DL 1 1 0100.2000.1005
1015 active 18448 SL 1 1 0100.2000.1001
1018 active 18451 SL 1 1 0100.2000.1005
1027 active 524283 DL 1 1 0100.2000.1001
1030 active 524282 DL 1 1 0100.2000.1005
1039 active 18460 SL 1 1 0100.2000.1001
1042 active 18463 SL 1 1 0100.2000.1005
1050 active 524281 DL 2 2 none
1056 active 18471 SL 2 2 none
1063 active 524280 DL 1 1 0100.2000.1001
1066 active 524279 DL 1 1 0100.2000.1005
1075 active 18478 SL 1 1 0100.2000.1001
1078 active 18481 SL 1 1 0100.2000.1005
1087 active 524278 DL 1 1 0100.2000.1001
1090 active 524277 DL 1 1 0100.2000.1005
1099 active 18490 SL 1 1 0100.2000.1001
1102 active 18493 SL 1 1 0100.2000.1005
1110 active 524276 DL 2 2 none
1116 active 18501 SL 2 2 none
-------------------------------------------------------------------------------
DL: dynamic local
SL: static local
-------------------------------------------------------------------------------
No. of SR Adjacency Sets: 20
===============================================================================
OSPF SR Adjacency Set Output Fields describes the OSPF sr-adj-sets output fields.
Label |
Description |
---|---|
ID |
Displays the ID. |
State |
Displays the state (active or inactive). |
Label Value |
Displays the label value. |
Label Type |
Displays the label type, Dynamic Local (DL) or Static Local (SL). |
Members Total |
Displays the number of total members. |
Members Active |
Displays the number of active members. |
Neighbor System Id |
Displays the neighbor system ID. |
No. of SR Adjacency Sets |
Displays the number of SR adjacency sets. |
sr-adjacencies
sr-adjacencies
Syntax
sr-adjacencies [ip-int-name | ip-address] [detail]
Context
[Tree] (tools>dump>router>isis sr-adjacencies)
Full Context
tools dump router isis sr-adjacencies
Description
This command displays IS-IS SR adjacency information.
Parameters
- ip-int-name
-
Specifies the IP interface name. An interface name cannot be in the form of an IP address. Interface names can be any string up to 32 characters long composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
- ip-address
-
Specifies the interface’s IP address.
Platforms
All
sr-adjacencies
Syntax
sr-adjacencies [ip-int-name | ip-address] [detail]
sr-adjacencies [remote ip-address] [ detail]
Context
[Tree] (tools>dump>router>ospf sr-adjacencies)
[Tree] (tools>dump>router>ospf3 sr-adjacencies)
Full Context
tools dump router ospf sr-adjacencies
tools dump router ospf3 sr-adjacencies
Description
This command displays OSPFv2 or OSPFv3 SR adjacency information.
Parameters
- ip-int-name
-
Specifies the IP interface name. An interface name cannot be in the form of an IP address. Interface names can be any string up to 32 characters, composed of printable, 7-bit ASCII characters. If the string contains special characters (#, $, spaces, etc.), the entire string must be enclosed within double quotes.
- ip-address
-
Specifies the interface’s IP address.
Platforms
All
Output
Output Example*A:Dut-C>config>router>ospf3# /tools dump router ospf3 0 sr-adjacencies detail
===============================================================================
Rtr Base OSPFv3 Instance 0 Segment Routing Adjacencies (detail)
Legend:
label stack is ordered from bottom-most to top-most
===============================================================================
-------------------------------------------------------------------------------
Interface DUTC_TO_DUTA.1.0
-------------------------------------------------------------------------------
Nbr RouterID : 10.20.1.1 Nbr State : FULL
Label : 524287 PgID : 9
SID Protection : Enabled Curr Hold Time : 15
Area ID : 0.0.0.1 SR MTU : 1492
Neighbor IP : fe80::200:ff:fe00:1-"DUTC_TO_DUTA.1.0"
LFA Labels : 30004/70005
LFA Next hop : fe80::200:ff:fe00:6-"DUTC_TO_DUTF.1.0"
LFA Glob Itf id: 26 LFA Loc Itf id : 3
-------------------------------------------------------------------------------
Interface DUTC_TO_DUTF.1.0
-------------------------------------------------------------------------------
Nbr RouterID : 10.20.1.6 Nbr State : FULL
Label : 524286 PgID : 10
SID Protection : Enabled Curr Hold Time : 15
Area ID : 0.0.0.1 SR MTU : 1492
Neighbor IP : fe80::200:ff:fe00:6-"DUTC_TO_DUTF.1.0"
LFA Labels : 30003/20005
LFA Next hop : fe80::200:ff:fe00:1-"DUTC_TO_DUTA.1.0"
LFA Glob Itf id: 25 LFA Loc Itf id : 2
-------------------------------------------------------------------------------
No. of SR Adjacencies: 2
===============================================================================
sr-database
sr-database
Syntax
sr-database [sid sid] [prefix ip-address] [nh-type {sr | bgp | rsvp}] [ipv4-unicast | ipv6-unicast] [algo algo-id] [detail]
Context
[Tree] (tools>dump>router>isis sr-database)
Full Context
tools dump router isis sr-database
Description
This command displays IS-IS SR database information.
Parameters
- sid
-
Displays information for the specific segment identifier.
- ip-address
-
Specifies the IP address in dotted decimal notation.
- sr
-
Displays information for SR next-hop route.
- bgp
-
Displays information for BGP next-hop route.
- rsvp
-
Displays information for RSVP next-hop route.
- ipv4-unicast
-
Displays IPv4 unicast parameters.
- ipv6-unicast
-
Displays IPv6 unicast parameters.
- algo algo-id
-
Filters information based on the specific algorithm only.
- detail
-
Displays detailed IS-IS SR database information.
Platforms
All
Output
The following outputs are examples of IS-IS SR database information, and IS-IS SR Database Output Fields describes the output fields.
Output Example*A:Dut-E# tools dump router isis sr-database
===============================================================================
Rtr Base ISIS Instance 0 SR Database
===============================================================================
SID Label Prefix Last-act Lev MT RtmPref TtmPref Metric IpNh SrNh
Mtu MtuPrim MtuBk D xL LT Act AdvSystemId SrErr
-------------------------------------------------------------------------------
0 60000 1.0.33.3 LfaNhops 1 0 15 11 100 1 1
1484 1500 1500 0 0 T +R 0100.2000.1003 SR_ERR_OK
1 60001 1.0.44.4 LfaNhops 1 0 15 11 200 1 1
1484 1500 1500 0 0 Tn +R 0100.2000.1004 SR_ERR_OK
2 60002 1.0.55.5 Local - - - - - - -
- - - 0 - - +R 0100.2000.1005 SR_ERR_OK
3 60003 1.0.66.6 LfaNhops 1 0 15 11 100 1 1
1484 1500 1500 0 0 T +R 0100.2000.1006 SR_ERR_OK
4 60004 1.0.11.1 LfaNhops 1 0 15 11 200 1 1
1484 1500 1500 0 0 Tn +R 0100.2000.1001 SR_ERR_OK
5 60005 1.0.22.2 LfaNhops 1 0 15 11 300 1 1
1484 1500 1500 0 0 Tn +R 0100.2000.1002 SR_ERR_OK
6 60006 10.20.1.3 LfaNhops 1 0 15 11 100 1 1
1484 1500 1500 0 0 T +R 0100.2000.1003 SR_ERR_OK
7 60007 10.20.1.4 LfaNhops 1 0 15 11 200 1 1
1484 1500 1500 0 0 Tn +R 0100.2000.1004 SR_ERR_OK
8 60008 10.20.1.5 Local - - - - - - -
- - - 0 - - +R 0100.2000.1005 SR_ERR_OK
9 60009 10.20.1.6 LfaNhops 1 0 15 11 100 1 1
1484 1500 1500 0 0 T +R 0100.2000.1006 SR_ERR_OK
10 60010 10.20.1.1 LfaNhops 1 0 15 11 200 1 1
1484 1500 1500 0 0 Tn +R 0100.2000.1001 SR_ERR_OK
11 60011 10.20.1.2 LfaNhops 1 0 15 11 300 1 1
1484 1500 1500 0 0 Tn +R 0100.2000.1002 SR_ERR_OK
-------------------------------------------------------------------------------
No. of Entries: 12
-------------------------------------------------------------------------------
Lev = route level
IpNh = number of IP next-hops
SrNh = number of SR-tunnel next-hops
D = duplicate pending
xL = exclude from LFA
LT = LFA type (L:LFA, R:RLFA, T:TILFA, n:nodeProtection)
Act = tunnel active state (R:reported, F:failed, +:SR-ack)
===============================================================================
Output Example
*A:Dut-C# tools dump router isis sr-database detail
===============================================================================
Rtr Base ISIS Instance 0 SR Database
Legend:
label stack is ordered from bottom-most to top-most
===============================================================================
-------------------------------------------------------------------------------
SID 601
-------------------------------------------------------------------------------
Label : 20601 Adv System Id : 0010.0100.1001
Prefix : 1.1.1.1
Route Level : 1 MT Id : 0
Rtm Preference : 15 Ttm Preference : 11
Metric : 10 Last Action : TnlChange
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.1.3.1 N 4 2 19 1 20601 0
-------------------------------------------------------------------------------
SID 602
-------------------------------------------------------------------------------
Label : 20602 Adv System Id : 0010.0100.1002
Prefix : 1.1.1.2
Route Level : 2 MT Id : 0
Rtm Preference : 18 Ttm Preference : 11
Metric : 10 Last Action : AddTnl
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.2.3.2 N 5 3 15 1 20602 0
-------------------------------------------------------------------------------
SID 603
-------------------------------------------------------------------------------
Label : 20603 Adv System Id : 0010.0100.1003
Prefix : 1.1.1.3 Type : Local
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
-------------------------------------------------------------------------------
SID 604
-------------------------------------------------------------------------------
Label : 20604 Adv System Id : 0010.0100.1004
Prefix : 1.1.1.4
Route Level : 2 MT Id : 0
Rtm Preference : 18 Ttm Preference : 11
Metric : 20 Last Action : AddTnl
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.2.3.2 N 5 3 15 0 20604 0
-------------------------------------------------------------------------------
SID 605
-------------------------------------------------------------------------------
Label : 20605 Adv System Id : 0010.0100.1005
Prefix : 1.1.1.5
Route Level : 2 MT Id : 0
Rtm Preference : 18 Ttm Preference : 11
Metric : 10 Last Action : AddTnl
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.3.5.5 N 6 4 17 1 20605 0
-------------------------------------------------------------------------------
SID 606
-------------------------------------------------------------------------------
Label : 20606 Adv System Id : 0010.0100.1006
Prefix : 1.1.1.6
Route Level : 2 MT Id : 0
Rtm Preference : 18 Ttm Preference : 11
Metric : 20 Last Action : AddTnl
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.3.5.5 N 6 4 17 0 20606 0
-------------------------------------------------------------------------------
SID 611 Algorithm 128
-------------------------------------------------------------------------------
Label : 20611 Adv System Id : 0010.0100.1001
Prefix : 1.1.1.1
Route Level : 1 MT Id : 0
Rtm Preference : 15 Ttm Preference : 11
Metric : 10 Last Action : TnlChange
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.1.3.1 N 4 2 19 1 20611 0
-------------------------------------------------------------------------------
SID 613
-------------------------------------------------------------------------------
Label : 20613 Adv System Id : 0010.0100.1003
Prefix : 1.1.1.3 Type : Local
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
-------------------------------------------------------------------------------
SID 614 Algorithm 128
-------------------------------------------------------------------------------
Label : 20614 Adv System Id : 0010.0100.1004
Prefix : 1.1.1.4
Route Level : 2 MT Id : 0
Rtm Preference : 18 Ttm Preference : 11
Metric : 20 Last Action : AddTnl
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.2.3.2 N 5 3 15 0 20614 0
-------------------------------------------------------------------------------
SID 615 Algorithm 128
-------------------------------------------------------------------------------
Label : 20615 Adv System Id : 0010.0100.1005
Prefix : 1.1.1.5
Route Level : 2 MT Id : 0
Rtm Preference : 18 Ttm Preference : 11
Metric : 10 Last Action : AddTnl
Num Ip NextHop : 1 Num SR-Tnl NextHop : 1
Mtu : 1560
Mtu Prim : 1564 Mtu Backup : -
Exclude from LFA : 0 LFA Type : -
Duplicate Pending : 0 Tunnel Active State : Reported/Ack
SR Error : SR_ERR_OK
NHOP: IP IsTunl GIfId/ IfId/ PgId IsAdv Label IsLfaX
TunlType LspId
-------------------------------------------------------------------------------
1.3.5.5 N 6 4 17 1 20615 0
Label |
Description |
---|---|
Label |
The ILM MPLS label corresponding to the SID |
Prefix |
The route prefix and mask |
Metric |
Interface metric for Level 1 and Level 2; if none are set to 0 |
sr-database
Syntax
sr-database [sid sid] [prefix ip-address] [nh-type {sr | ldp | rsvp}] [algo algo-id] [detail]
Context
[Tree] (tools>dump>router>ospf sr-database)
Full Context
tools dump router ospf sr-database
Description
This command displays OSPFv2 SR database information.
Parameters
- sid
-
Displays information for the specific segment identifier.
- ip-address
-
Specifies the IP address in dotted decimal notation.
- algo-id
-
Displays the OSPFv2 database information for the specified algorithm identifier.
Platforms
All
Output
The following output is an example of OSPFv2 SR database information.
Output Example*A:Dut-C# tools dump router ospf sr-database
===============================================================================
Rtr Base OSPFv2 Instance 0 Segment Routing Database
===============================================================================
SID Label St Type Prefix Stitching
Algo AdvRtr Area Flags FRR
-------------------------------------------------------------------------------
2 100002 +R T1 10.20.1.2/32 -
0 10.20.1.2 0.0.0.0 [NnP ] L(R)
3 100003 +R LT1 10.20.1.3/32 -
0 10.20.1.3 0.0.0.0 [NnP ] -
5 100005 +R T1 10.20.1.5/32 -
0 10.20.1.5 0.0.0.0 [NnP ] L(R)
1282 101282 +R T1 10.20.1.2/32 -
128 10.20.1.2 0.0.0.0 [NnP ] -
1283 101283 +R LT1 10.20.1.3/32 -
128 10.20.1.3 0.0.0.0 [NnP ] -
1285 101285 +R T1 10.20.1.5/32 -
128 10.20.1.5 0.0.0.0 [NnP ] -
-------------------------------------------------------------------------------
No. of Entries: 6
-------------------------------------------------------------------------------
St: R:reported I:incomplete W:wrong N:not reported F:failed
+:SR-ack -:no route
Type: L:local M: mapping Srv Tx: route type
FRR: L:Lfa R:RLfa T:TiLfa (R):Reported (F):Failed
Ln, Rn, Tn: FRR providing node-protection
===============================================================================
*A:Dut-C# tools dump router ospf sr-database algo 128
===============================================================================
Rtr Base OSPFv2 Instance 0 Algo 128 Segment Routing Database
===============================================================================
SID Label St Type Prefix Stitching
Algo AdvRtr Area Flags FRR
-------------------------------------------------------------------------------
1282 101282 +R T1 10.20.1.2/32 -
128 10.20.1.2 0.0.0.0 [NnP ] -
1283 101283 +R LT1 10.20.1.3/32 -
128 10.20.1.3 0.0.0.0 [NnP ] -
1285 101285 +R T1 10.20.1.5/32 -
128 10.20.1.5 0.0.0.0 [NnP ] -
-------------------------------------------------------------------------------
No. of Entries: 3
-------------------------------------------------------------------------------
St: R:reported I:incomplete W:wrong N:not reported F:failed
+:SR-ack -:no route
Type: L:local M: mapping Srv Tx: route type
FRR: L:Lfa R:RLfa T:TiLfa (R):Reported (F):Failed
Ln, Rn, Tn: FRR providing node-protection
===============================================================================
sr-database
Syntax
sr-database [sid sid] [prefix ip-address] [nh-type {sr | ldp | rsvp}] [detail]
Context
[Tree] (tools>dump>router>ospf3 sr-database)
Full Context
tools dump router ospf3 sr-database
Description
This command displays OSPFv3 SR database information.
Parameters
- sid
-
Displays information for the specific segment identifier.
- ip-address
-
Specifies the IP address in dotted decimal notation.
Platforms
All
Output
Output ExampleA:Dut-E# tools dump router ospf sr-database
===============================================================================
Rtr Base OSPFv2 Instance 0 Segment Routing Database
===============================================================================
SID Label St Type Prefix Stitching
AdvRtr Area Flags FRR
-------------------------------------------------------------------------------
0 60000 +R T1 1.0.33.3/32 -
10.20.1.3 0.0.0.0 [NnP ] T(R)
1 60001 +R T1 1.0.44.4/32 -
10.20.1.4 0.0.0.0 [NnP ] Tn(R)
2 60002 +R LT1 1.0.55.5/32 -
10.20.1.5 0.0.0.0 [NnP ] -
3 60003 +R T1 1.0.66.6/32 -
10.20.1.6 0.0.0.0 [NnP ] T(R)
4 60004 +R T1 1.0.11.1/32 -
10.20.1.1 0.0.0.0 [NnP ] Tn(R)
5 60005 +R T1 1.0.22.2/32 -
10.20.1.2 0.0.0.0 [NnP ] Tn(R)
6 60006 +R T1 10.20.1.3/32 -
10.20.1.3 0.0.0.0 [NnP ] T(R)
7 60007 +R T1 10.20.1.4/32 -
10.20.1.4 0.0.0.0 [NnP ] Tn(R)
8 60008 +R LT1 10.20.1.5/32 -
10.20.1.5 0.0.0.0 [NnP ] -
9 60009 +R T1 10.20.1.6/32 -
10.20.1.6 0.0.0.0 [NnP ] T(R)
10 60010 +R T1 10.20.1.1/32 -
10.20.1.1 0.0.0.0 [NnP ] Tn(R)
11 60011 +R T1 10.20.1.2/32 -
10.20.1.2 0.0.0.0 [NnP ] Tn(R)
-------------------------------------------------------------------------------
No. of Entries: 12
-------------------------------------------------------------------------------
St: R:reported I:incomplete W:wrong N:not reported F:failed
+:SR-ack -:no route
Type: L:local M: mapping Srv Tx: route type
FRR: L:Lfa R:RLfa T:TLfa (R):Reported (F):Failed
Rn: RLfa + node-protect Tn: TLfa + node-protect
===============================================================================
*A:Dut-F# tools dump router ospf sr-database detail
====================================================================================
Rtr Base OSPFv2 Instance 0 Segment Routing Database (detail)
====================================================================================
SID Label Sts Prefix Type AdvRtr Area Flags
TnlID FRR
lsId AdvRtr Area Type
------------------------------------------------------------------------------------
0 70000 +R 1.0.33.3/
32 T1 10.20.1.3 0.0.0.1 [NnP ] 2 R(R)
7.16.0.9 10.20.1.2 0.0.0.0 T3
7.0.0.4 10.20.1.3 0.0.0.1 T1 <<<< Best
1 70001 +R 1.0.44.4/
32 T1 10.20.1.4 0.0.0.0 [NnP ] 2 L(R)
7.16.0.5 10.20.1.2 0.0.0.1 T3
7.0.0.4 10.20.1.4 0.0.0.0 T1 <<<< Best
2 70002 +R 1.0.55.5/
32 T1 10.20.1.5 0.0.0.0 [NnP ] 2 R(R)
7.16.0.3 10.20.1.2 0.0.0.1 T3
7.0.0.4 10.20.1.5 0.0.0.0 T1 <<<< Best
3 70003 +R 1.0.66.6/
32 LT1 10.20.1.6 0.0.0.1 [NnP ] 0 -
7.16.0.8 10.20.1.2 0.0.0.0 T3
7.0.0.6 10.20.1.6 0.0.0.1 T1 <<<< Best
4 70004 +R 1.0.11.1/
32 T1 10.20.1.1 0.0.0.1 [NnP ] 2 L(R)
7.16.0.13 10.20.1.2 0.0.0.0 T3
7.0.0.4 10.20.1.1 0.0.0.1 T1 <<<< Best
5 70005 +R 1.0.22.2/
32 T1 10.20.1.2 0.0.0.1 [NnP ] 2 R(R)
7.16.0.11 10.20.1.2 0.0.0.0 T3
7.0.0.6 10.20.1.2 0.0.0.1 T1 <<<< Best
6 70006 +R 10.20.1.3/
32 T1 10.20.1.3 0.0.0.1 [NnP ] 2 R(R)
7.16.0.10 10.20.1.2 0.0.0.0 T3
7.0.0.5 10.20.1.3 0.0.0.1 T1 <<<< Best
7 70007 +R 10.20.1.4/
32 T1 10.20.1.4 0.0.0.0 [NnP ] 2 L(R)
7.16.0.6 10.20.1.2 0.0.0.1 T3
7.0.0.5 10.20.1.4 0.0.0.0 T1 <<<< Best
8 70008 +R 10.20.1.5/
32 T1 10.20.1.5 0.0.0.0 [NnP ] 2 R(R)
7.16.0.4 10.20.1.2 0.0.0.1 T3
7.0.0.5 10.20.1.5 0.0.0.0 T1 <<<< Best
9 70009 +R 10.20.1.6/
32 LT1 10.20.1.6 0.0.0.0 [NnP ] 0 -
7.16.0.2 10.20.1.2 0.0.0.1 T3
7.0.0.7 10.20.1.6 0.0.0.0 T1 <<<< Best
10 70010 +R 10.20.1.1/
32 T1 10.20.1.1 0.0.0.1 [NnP ] 2 L(R)
7.16.0.12 10.20.1.2 0.0.0.0 T3
7.0.0.5 10.20.1.1 0.0.0.1 T1 <<<< Best
11 70011 +R 10.20.1.2/
32 T1 10.20.1.2 0.0.0.0 [NnP ] 2 R(R)
7.16.0.7 10.20.1.2 0.0.0.1 T3
7.0.0.7 10.20.1.2 0.0.0.0 T1 <<<< Best
994 70994 +R 1.0.44.4/
32 T1 10.20.1.5 0.0.0.0 [NnPB ] 0 -
7.16.0.1 10.20.1.5 0.0.0.0 T1 <<<< Best
995 70995 +R 1.0.55.5/
32 T1 10.20.1.4 0.0.0.0 [NnPB ] 0 -
7.16.0.1 10.20.1.4 0.0.0.0 T1 <<<< Best
996 70996 +R 1.0.22.2/
32 LT1 10.20.1.6 0.0.0.1 [NnPB ] 0 -
997 70997 - 1.0.66.6/
32 T1 10.20.1.2 0.0.0.1 [NnPB ] - -
7.16.0.1 10.20.1.2 0.0.0.1 T1 <<<< Best
998 70998 +R 1.0.33.3/
32 T1 10.20.1.1 0.0.0.1 [NnPB ] 0 -
7.16.0.1 10.20.1.1 0.0.0.1 T1 <<<< Best
999 70999 +R 1.0.11.1/
32 T1 10.20.1.3 0.0.0.1 [NnPB ] 0 -
7.16.0.1 10.20.1.3 0.0.0.1 T1 <<<< Best
------------------------------------------------------------------------------------
Sts: R:reported I:incomplete W:wrong N:not reported F:failed +:SR-ack -
:no route
Type: L:local M: mapping Srv Tx: route type
FRR: L:Lfa R:RLfa (R):Reported (F):Failed
====================================================================================
*A:Dut-F#
sr-label
sr-label
Syntax
sr-label
Context
[Tree] (show>router>bgp sr-label)
Full Context
show router bgp sr-label
Description
This command displays BGP SR label information.
Platforms
All
sr-lfa-coverage
sr-lfa-coverage
Syntax
sr-lfa-coverage [flex-algo {flex-algo-id | all}]
Context
[Tree] (show>router>isis sr-lfa-coverage)
Full Context
show router isis sr-lfa-coverage
Description
This command displays IS-IS SR LFA coverage information. This corresponds to the coverage provided by the various LFA algorithms for SR-ISIS tunnel, SR-TE LSP, and LDP FEC if the fast-reroute backup-sr-tunnel option is enabled. The LFA algorithms activate the backup next hops in the following preference order:
-
TI-LFA
-
LFA
-
R-LFA
Parameters
- flex-algo flex-algo-id
-
Displays SR LFA coverage information for the specified algorithm.
- all
-
Displays all the flexible algorithms that are configured.
Platforms
All
Output
The following output is an example of SR LFA coverage information, and IS-IS SR LFA Coverage Output Fields describes the output fields.
Output Example*A:Dut-C>config>router>isis# show router isis 0 sr-lfa-coverage
===============================================================================
Rtr Base ISIS Instance 0 SR LFA Coverage
===============================================================================
MT-ID SidType Level Proto LFA RLFA TILFA Coverage
-------------------------------------------------------------------------------
node-sid 4(40%) 6(60%) 0(0%) 10/10(100%)
adj-sid 0(0%) 2(100%) 0(0%) 2/2(100%)
===============================================================================
Output Example
A:Dut-A# show router isis 0 sr-lfa-coverage flex-algo 128
===============================================================================
Rtr Base ISIS Instance 0 Flex-Algo 128 SR LFA Coverage
===============================================================================
MT-ID SidType Level Proto LFA RLFA TILFA Coverage
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
A:Dut-A# show router isis 0 sr-lfa-coverage flex-algo all
===============================================================================
Rtr Base ISIS Instance 0 Flex-Algo 128 SR LFA Coverage
===============================================================================
MT-ID SidType Level Proto LFA RLFA TILFA Coverage
-------------------------------------------------------------------------------
No Matching Entries
===============================================================================
IS-IS SR LFA Coverage Output Fields describes the IS-IS SR LFA coverage output fields.
Label |
Description |
---|---|
MT-ID |
Displays the MT identification |
SidType |
Displays the SID type |
Level |
Displays the level |
Proto |
Displays the protocol |
LFA |
Displays the LFA |
RLFA |
Displays the RLFA |
TIFLA |
Displays the TI-LFA |
Coverage |
Displays the percentage of coverage |
sr-lfa-coverage
Syntax
sr-lfa-coverage [area area-id] [flex-algo { flex-algo-id | all}]
Context
[Tree] (show>router>ospf sr-lfa-coverage)
Full Context
show router ospf sr-lfa-coverage
Description
This command displays the details of the OSPF SR LFA coverage. This corresponds to the coverage provided by the various LFA algorithms for SR-OSPF tunnel, SR-TE LSP, and LDP FEC if fast-reroute backup-sr-tunnel option is enabled. The LFA algorithms activate the backup next hops using the preference order:
-
TI-LFA
-
LFA
-
R-LFA
Parameters
- area area-id
-
Displays all interfaces configured in this area.
- flex-algo flex-algo-id
-
Displays the OSPF SR LFA coverage details for the specified segment routing algorithm.
- flex-algo all
-
Displays the OSPF SR LFA coverage details for all segment routing algorithms.
Platforms
All
Output
The following output is an example of OSPF SR LFA coverage, and OSPF SR LFA Coverage Output Fields describes the output fields.
Output Example*A:Dut-C# show router ospf sr-lfa-coverage flex-algo 128
===============================================================================
Rtr Base OSPFv2 Instance 0 Flex-Algo 128 SR LFA Coverage
===============================================================================
SidType Area LFA RLFA TILFA Coverage
-------------------------------------------------------------------------------
node-sid 0.0.0.0 2(100%) 0(0%) 0(0%) 2/2(100%)
===============================================================================
*A:Dut-C#
Label |
Description |
---|---|
SidType |
Displays the SID type. |
Area |
Displays the OSPF area. |
LFA |
Displays the LFA. |
RLFA |
Displays the RLFA. |
TIFLA |
Displays the TI-LFA. |
Coverage |
Displays the percentage of coverage. |
sr-lfa-coverage
Syntax
sr-lfa-coverage [area area-id]
Context
[Tree] (show>router>ospf3 sr-lfa-coverage)
Full Context
show router ospf3 sr-lfa-coverage
Description
This command displays the details of the OSPF SR LFA coverage. This corresponds to the coverage provided by the various LFA algorithms for SR-OSPF tunnel, SR-TE LSP, and LDP FEC if fast-reroute backup-sr-tunnel option is enabled. The LFA algorithms activate the backup next hops using the preference order:
-
TI-LFA
-
LFA
-
R-LFA
Parameters
- area area-id
-
Displays all interfaces configured in this area.
Platforms
All
Output
Output Example*A:Dut-C>config>router>ospf3# show router ospf3 0 sr-lfa-coverage
===============================================================================
Rtr Base OSPFv3 Instance 0 SR LFA Coverage
===============================================================================
SidType Area LFA RLFA TILFA Coverage
-------------------------------------------------------------------------------
node-sid 0.0.0.1 4(40%) 6(60%) 0(0%) 10/10(100%)
adj-sid 0.0.0.1 0(0%) 2(100%) 0(0%) 2/2(100%)
===============================================================================
The following table describes the OSPF SR LFA coverage output fields.
Label |
Description |
---|---|
SidType |
Displays the SID type. |
Area |
Displays the OSPF area. |
LFA |
Displays the LFA. |
RLFA |
Displays the RLFA. |
TIFLA |
Displays the TI-LFA. |
Coverage |
Displays the percentage of coverage. |
sr-lfa-info
sr-lfa-info
Syntax
sr-lfa-info [ipv4-unicast | ipv6-unicast | mt mt-id-number] [prefix ip-prefix[/prefix-length]] [algo algo-id] [detail]
Context
[Tree] (show>router>isis sr-lfa-info)
Full Context
show router isis sr-lfa-info
Description
This command displays IS-IS SR LFA information.
Parameters
- ipv4-unicast
-
Keyword used to display IPv4 unicast parameters.
- ipv6-unicast
-
Keyword used to display IPv6 unicast parameters.
- mt-id-number
-
Displays the MT ID parameters.
- ip-prefix/prefix-length
-
Displays the specified IP prefix.
- algo-id
-
Filters information based on the specific algorithm only.
- detail
-
Displays detailed information.
Platforms
All
Output
The following output is an example of SR LFA information, and IS-IS SR LFA information Output Fields describes the output fields.
Output Exampleshow router isis sr-lfa-info prefix 192.0.2.2/32 algo 253
==========================================================================
Rtr Base ISIS Instance 0 SR LFA Info
==========================================================================
Prefix Algo MT
NextHop
LFA-NextHop LfaType (Pr-Type)
Backup-Node NodeType SID SID-Type
--------------------------------------------------------------------------
192.0.2.1/32 253 0
192.168.13.1
192.168.36.2(L) TI-LFA (Link)
1920.0000.2006 P-Node 524285 Adjacency
1920.0000.2004 TR-Node 524287 Adjacency
1920.0000.2002 TR-Node 524287 Adjacency
1920.0000.2001 Q-Node - -
--------------------------------------------------------------------------
No. of Entries: 1
Pr-Type : Link = linkProtection, Node = nodeProtection
==========================================================================
Label |
Description |
---|---|
Rtr Base ISIS Instance 0 SR LFA Info |
|
Prefix |
Displays the prefix IP address |
Algo |
Displays the algorithm ID |
MT |
Displays the Multi-Topology value |
NextHop |
Displays the next-hop IP address |
LFA-NextHop |
Displays the LFA next-hop IP address |
LfaType (Pr-Type) |
Displays the LFA type |
Backup-Node |
Displays the backup node system ID |
NodeType |
Displays the node type |
SID |
Displays the SID value |
SID-Type |
Displays the SID type |
No. of Entries |
Displays the total number of entries |
The following output is an example of detailed SR LFA information, and IS-IS SR LFA detailed information Output Fields describes the output fields.
Output Exampleshow router isis sr-lfa-info prefix 192.0.2.2/32 algo 253 detail
===============================================================================
Rtr Base ISIS Instance 0 SR LFA Info (detail)
===============================================================================
-------------------------------------------------------------------------------
SR Tunnel Prefix : 192.0.2.1/32
-------------------------------------------------------------------------------
Algorithm : 253
MT : 0
NextHop : 192.168.13.1
LFA-NextHop : 192.168.36.2
LFA-Type : TI-LFA
LFA-Protection : Link Protection
-------------------------------------------------------------------------------
Displaying Backup-Node-Info
-------------------------------------------------------------------------------
Node-count : 4
Node-SysID : 1920.0000.2006
Node-Type : P-Node
SID : 524285
SID-Type : Adjacency
Node-SysID : 1920.0000.2004
Node-Type : TR-Node
SID : 524287
SID-Type : Adjacency
Node-SysID : 1920.0000.2002
Node-Type : TR-Node
SID : 524287
SID-Type : Adjacency
Node-SysID : 1920.0000.2001
Node-Type : Q-Node
SID : -
SID-Type : -
-------------------------------------------------------------------------------
No. of Entries: 1
===============================================================================
Label |
Description |
---|---|
Rtr Base ISIS Instance 0 SR LFA Info (detail) |
|
SR Tunnel Prefix |
Displays the SR tunnel prefix IP address |
Algorithm |
Displays the algorithm ID |
MT |
Displays the MT value |
NextHop |
Displays the next-hop IP address |
LFA-NextHop |
Displays the LFA next-hop IP address |
LFA-Type |
Displays the LFA type |
LFA-Protection |
Displays the LFA protection type |
Displaying Backup-Node-Info |
|
Node-count |
Displays the number of nodes |
Node-SysID |
Displays the node system ID |
Node-Type |
Displays the node type |
SID |
Displays the SID value |
SID-Type |
Displays the SID type |
No. of Entries |
Displays the total number of entries |
sr-policies
sr-policies
Syntax
sr-policies
Context
[Tree] (clear>router>seg-rt sr-policies)
Full Context
clear router segment-routing sr-policies
Description
Commands in this context clear SR policies statistics.
Platforms
All
sr-policies
Syntax
sr-policies
Context
[Tree] (show>router>seg-rt sr-policies)
Full Context
show router segment-routing sr-policies
Description
Commands in this context display SR policy information.
Platforms
All
sr-policies
Syntax
sr-policies
Context
[Tree] (monitor>router>seg-rt sr-policies)
Full Context
monitor router segment-routing sr-policies
Description
Commands in this context monitor Segment Routing SR Policy Statistics.
Platforms
All
sr-policy-ipv4
sr-policy-ipv4
Syntax
sr-policy-ipv4 [rd rd] [color color] [endpoint ip-address]
Context
[Tree] (show>router>bgp>routes sr-policy-ipv4)
Full Context
show router bgp routes sr-policy-ipv4
Description
This command displays BGP SR policy IPv4 routes.
Parameters
- ip-address
-
Specifies the endpoint IPv4 address.
Platforms
All
sr-policy-ipv6
sr-policy-ipv6
Syntax
sr-policy-ipv6 [rd rd] [color color] [endpoint ipv6-address]
sr-policy-ipv6 hunt [rd rd] [color color] [endpoint ipv6-address]
Context
[Tree] (show>router>bgp>routes sr-policy-ipv6)
Full Context
show router bgp routes sr-policy-ipv6
Description
This command displays BGP SR policy IPv6 routes.
Parameters
- ipv6-address
-
Specifies the endpoint IPv6 address, up to 64 characters
Platforms
All
sr-te
sr-te
Syntax
sr-te
Context
[Tree] (clear>router>mpls>lsp>auto-lsp sr-te)
Full Context
clear router mpls lsp auto-lsp sr-te
Description
This command resets and restarts all auto SR-TE LSPs.
Platforms
All
sr-te
Syntax
sr-te
Context
[Tree] (clear>router>mpls>lsp sr-te)
Full Context
clear router mpls lsp sr-te
Description
This command resets and restarts all SR-TE LSPs.
Platforms
All
sr-te-cspf
sr-te-cspf
Syntax
sr-te-cspf [path-computation-method path-computation-method] to ip-address [path path-name] [from ip-address] [include-bitmap bitmap] [exclude-bitmap bitmap] [hop-limit limit] [metric-type-te] [ local-sr-protection local-sr-protection] [ label-stack-reduction] [max-sr-labels label-stack-size] [ exclude-address excl-addr [excl-addr]] [ exclude-node excl-node-id [excl-node-id]] [ skip-interface interface-name]
Context
[Tree] (tools>perform>router>mpls sr-te-cspf)
Full Context
tools perform router mpls sr-te-cspf
Description
This command computes and returns one or more SR-TE paths and corresponding label stack to a given destination router and with the specified constraints.
By default, or when the user specifies the value of ip-to-label for the path-computation-method parameter, MPLS passes the to path and the from parameters to TE-DB, which converts the list of hops into a label stack by scanning the TE database for adjacency and node SID information that belongs to the router or link identified by each hop address. If the conversion is successful, the TE database returns the actual selected hop SIDs plus labels, as well as the configured path hop addresses that were used as the input for this conversion. None of the TE constraint parameters are used in this path computation method.
When the user specifies the value of local-cspf for the path-computation-method parameter, MPLS passes all parameters of the tools command, including the TE constraint parameters. In this case, a full CSPF is run using these parameters.
When the user runs this tools command without specifying a path name, CSPF returns the set of candidate ECMP paths. When the user specifies a path name, CSPF returns a single path, which is selected randomly similar to a configured SR-TE LSP, with the path-computation-method local-cspf command enabled.
Parameters
- to ip-address
-
Specifies the destination address.
- path path-name
-
Specifies the path name, up to 64 characters.
- from ip-address
-
Specifies the originating IP address.
- path-computation-method path-computation-method
-
Specifies the path computation method of the LSP path.
- hop-limit limit
-
Specifies the maximum number of hops for the path.
- exclude-bitmap bitmap
-
Specifies a bit-map of the admin groups that should be excluded in the path computation. Accepted in decimal, hex, or binary.
- include-bitmap bitmap
-
Specifies a bit-map of the admin groups that should be included in the path. Accepted in decimal, hex, or binary.
- metric-type-te
-
Specifies the use of the traffic engineering metric to optimize the path. By default, the link IGP metric is used.
- local-sr-protection
-
Specifies the local LFA protection desired for the CSPF computed explicit path with adjacency SIDs.
- label-stack-reduction
-
Specifies to apply label stack reduction to the CSPF computed explicit path with adjacency SIDs.
- max-sr-labels label-stack-size
-
Specifies the maximum label stack size of the CSPF computed path with or without label stack reduction.
- exclude-address ip-addr
-
Specifies a list of up to eight IP addresses that should be excluded in the path computation.
- exclude-node excl-node-id
-
Specifies a list of up to eight addresses that should be excluded during the path computation.
- skip-interface interface-name
-
Specifies an interface name, up to 32 characters, that should be skipped during the path computation.
Platforms
All
sr-te-lsp
sr-te-lsp
Syntax
sr-te-lsp [lsp-name] [status {up | down}] [detail] path [path-name] [auto-lsp {all | mesh-p2p-srte | one-hop-p2p-srte| on-demand-p2p-srte}] [family family]
sr-te-lsp count
sr-te-lsp [lsp-name] [detail] [ auto-lsp {all | mesh-p2p-srte | one-hop-p2p-srte | on-demand-p2p-srte}] [family family]
sr-te-lsp [lsp-name] [status {up | down}] [to {ip-address | ipv6-address}] [detail] [auto-lsp { all | mesh-p2p-srte | one-hop-p2p-srte | on-demand-p2p-srte}] [family family]
sr-te-lsp [lsp-name] activepath [ auto-lsp {all | mesh-p2p-srte | one-hop-p2p-srte | on-demand-p2p-srte}] [family family]
sr-te-lsp [lsp-name] egress-stats
sr-te-lsp [lsp-name] path [path-name] [ auto-lsp {all | mesh-p2p-srte | one-hop-p2p-srte | on-demand-p2p-srte}] mbb
Context
[Tree] (show>router>mpls sr-te-lsp)
Full Context
show router mpls sr-te-lsp
Description
This command displays SR-TE LSP information.
Parameters
- lsp-name
-
Specifies the SR-TE LSP name, up to 64 characters.
- status
-
Allows filtering of the output based on the status of the SR-TE LSP.
- detail
-
Displays detailed information.
- path-name
-
Specifies the SR-TE LSP path name, up to 64 characters.
- auto-lsp
-
Displays the type of automatic LSP.
- family
-
Displays the family of IP addresses.
- count
-
Displays the total number of SR-TE LSPs.
- to {ip-address | ipv6-address}
-
Displays the IPv4 or IPv6 address of the egress router for the LSP.
- egress-stats
-
Displays the traffic statistics for the specified SR-TE LSP or for all SR-TE LSPs if none is explicitly specified. Traffic statistics are provided for primary path, secondary path if any, and secondary standby paths, if any. Statistics are preserved across switchover only for primary and secondary standby paths.
- mbb
-
Displays make-before-break (MBB) information.
- activepath
-
Displays the SR-TE active paths, which are candidate paths selected as the best paths by the SR policy.make-before-break (MBB) information.
Platforms
All
Output
The following outputs are examples of MPLS SR-TE LSP information. The associated tables describe the output fields.
Output ExampleThe following outputs apply to an SR-TE LSP for which the path is computed using the local SR-TE CSPF method.
*A:Dut-C# show router mpls sr-te-lsp "C_F_70000"
===============================================================================
MPLS SR-TE LSPs (Originating)
===============================================================================
LSP Name To Tun Protect Adm Opr
Id Path
-------------------------------------------------------------------------------
C_F_70000 10.20.1.6 1 N/A Up Up
-------------------------------------------------------------------------------
LSPs : 1
===============================================================================
*A:Dut-C# show router mpls sr-te-lsp "C_F_70000" detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
Legend :
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : C_F_70000
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 10.20.1.3 To : 10.20.1.6
Adm State : Up Oper State : Up
LSP Up Time : 0d 11:40:44 LSP Down Time : 0d 00:00:00
Transitions : 3 Path Changes : 3
Retry Limit : 0 Retry Timer : 10 sec
Hop Limit : 255 Negotiated MTU : 1484
PathCompMethod : local-cspf
FallbkPathComp : not-applicable
Metric : 1000 Metric Type : igp
Local Sr Protec*: preferred Label Stack Reduction: Enabled
Load Bal Wt : N/A ClassForwarding : Disabled
Include Grps : Exclude Grps :
None None
BFD Template : None BFD Ping Intvl : N/A
BFD Enable : False BFD Failure-action : None
WaitForUpTimer : 4
Revert Timer : Disabled Next Revert In : N/A
Entropy Label : Enabled+ Oper Entropy Label : Enabled
Negotiated EL : Disabled
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 1000
PCE Report : Disabled+
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile : None
Admin Tags : None
Primary(a) : C_F_70000
Up Time : 0d 11:40:44
Bandwidth : 0 Mbps
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C# show router mpls sr-te-lsp "C_F_70000" activepath
===============================================================================
MPLS LSP: C_F_70000 (active paths)
===============================================================================
Legend :
# - Manually switched path
#F - Manually forced switched path
===============================================================================
LSP Name : C_F_70000
LSP Id : 26114
Path Name : C_F_70000
Active Path : Primary
To : 10.20.1.6 LSP Type : SR-TE
===============================================================================
*A:Dut-C# tools perform router mpls sr-te-cspf to 10.20.1.6 path "C_F_70000" hop-
limit 3 label-stack-reduction path-computation-method local-cspf max-sr-labels 4
Req CSPF TE path
From: this node To: 10.20.1.6
CSPF TE Path
To: 10.20.1.6
[1] Source Add 10.20.1.3 Cost 4000
Hop 1 -> Label 524242 NH 10.10.2.3 --> 10.10.2.1 (10.20.1.1) Cost 1000 Color 0x0
Hop 2 -> Label 434687 NH :: --> 10.20.1.2 (10.20.1.2) Cost 1000 Color 0x0
Hop 3 -> Label 435087 NH :: --> 10.20.1.4 (10.20.1.4) Cost 1000 Color 0x0
Hop 4 -> Label 435487 NH :: --> 10.20.1.6 (10.20.1.6) Cost 1000 Color 0x0
*A:Dut-C#
*A:Dut-C# tools perform router mpls resignal sr-te-lsp "C_F_70000" path "C_F_70000"
*A:Dut-C#
1 2019/07/03 19:36:37.768 UTC WARNING: MPLS #2014 Base VR 1:
"LSP path C_F_70000::C_F_70000 resignaled as a result of manualResignal MBB"
*A:Dut-C# tools perform router mpls sr-te-cspf to 10.20.1.6 path "C_F_70000" hop-
limit 3 label-stack-reduction path-computation-method local-cspf max-sr-labels 4
Req CSPF TE path
From: this node To: 10.20.1.6
CSPF TE Path
To: 10.20.1.6
[1] Source Add 10.20.1.3 Cost 4000
Hop 1 -> Label 524242 NH 10.10.2.3 --> 10.10.2.1 (10.20.1.1) Cost 1000 Color 0x0
Hop 2 -> Label 434687 NH :: --> 10.20.1.2 (10.20.1.2) Cost 1000 Color 0x0
Hop 3 -> Label 435087 NH :: --> 10.20.1.4 (10.20.1.4) Cost 1000 Color 0x0
Hop 4 -> Label 435487 NH :: --> 10.20.1.6 (10.20.1.6) Cost 1000 Color 0x0
*A:Dut-C#
*A:Dut-C# tools perform router mpls resignal sr-te-lsp "C_F_70000" path "C_F_70000"
*A:Dut-C#
1 2019/07/03 19:36:37.768 UTC WARNING: MPLS #2014 Base VR 1:
"LSP path C_F_70000::C_F_70000 resignaled as a result of manualResignal MBB"
Output Example
The following show outputs display an LSP with BFD configured to use controlled return path. The following tables describe the MPLS SR-TE LSP detail fields and the MPLS SR-TE LSP path detail fields.
*A:Dut-C# /show router mpls sr-te-lsp detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
Legend :
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : to_A_SR_TE
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 3.3.3.3
To : 1.1.1.1
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:00:05 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 2 sec
Hop Limit : 255 Negotiated MTU : 1496
PathCompMethod : none
FallbkPathComp : not-applicable
Metric : N/A
Local Sr Protec*: preferred Label Stack Reduction: Disabled
Load Bal Wt : N/A ClassForwarding : Disabled
Include Grps : Exclude Grps :
None None
Egress Stats : Disabled
BFD Template : None BFD Ping Intvl : N/A
BFD Enable : False BFD Failure-action : None
WaitForUpTimer : 4
ReturnPathLabel : None
Revert Timer : Disabled Next Revert In : N/A
Entropy Label : Enabled+ Oper Entropy Label : Enabled
Negotiated EL : Disabled Override Tunnel ELC : Disabled
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 16777215
PCE Report : Disabled+
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile : None
Admin Tags : None
Primary(a) : path_A
Up Time : 0d 00:00:09
Bandwidth : 0 Mbps
Secondary : path_A2
Down Time : 0d 00:00:50
Bandwidth : 0 Mbps
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : template-1.1.1.1-671747
LSP Type : OneHopP2PSrTe LSP Tunnel ID : 16386
LSP Index : 81921 TTM Tunnel Id : 671747
From : 30.30.2.2
To : 1.1.1.1
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:00:08 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
PathCompMethod : none
FallbkPathComp : not-applicable
Metric : N/A
Local Sr Protec*: preferred Label Stack Reduction: Disabled
Load Bal Wt : N/A ClassForwarding : Disabled
Include Grps : Exclude Grps :
None None
Egress Stats : Disabled
BFD Template : srte BFD Ping Intvl : N/A
BFD Enable : True BFD Failure-action : None
WaitForUpTimer : 4
ReturnPathLabel : 35002
Revert Timer : Disabled Next Revert In : N/A
Entropy Label : Enabled+ Oper Entropy Label : Enabled
Negotiated EL : Disabled Override Tunnel ELC : Disabled
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 16777215
OriginTemplName : template
Admin Tags : None
PCE Report : Disabled+
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile : None
Primary(a) : path_A
Up Time : 0d 00:00:09
Bandwidth : 0 Mbps
===============================================================================
* indicates that the corresponding row element may have been truncated.
Label |
Description |
---|---|
LSP Name |
The name of the LSP |
LSP Type |
The type of the LSP |
LSP Tunnel ID |
The tunnel ID number for the LSP used in the interaction with PCC/PCE |
LSP Index |
The LSP index used for indexing the LSP in the MIB table shared with the RSVP-TE LSP |
TTM Tunnel Id |
The tunnel ID number for the tunnel representing the LSP in the tunnel table |
From |
The IP address for the ingress router for the LSP |
To |
The IP address for the egress router for the LSP |
Admin State |
The administrative state of the LSP |
Oper State |
The operational state of the LSP |
LSP Up Time |
The length of time the LSP has been operational |
LSP Down Time |
The amount of time the LSP has been down |
Transitions |
The number of transitions that have occurred for the LSP |
Path Changes |
The number of times the path has changed |
Retry Limit |
The number of attempts that the software makes to reestablish the LSP after it has failed |
Retry Timer |
The time, in seconds, for LSP reestablishment attempts after LSP failure |
Hop Limit |
The maximum number of hops that an LSP can traverse, including the ingress and egress routers |
Negotiated MTU |
The size of the maximum transmission unit (MTU) that is negotiated during establishment of the LSP |
PathCompMethod |
pce — PCE path computation method is configured local-cspf — Local CSPF path computation method is configured none — No computation method is configured |
FallbkPathComp |
none — No fallback method is configured local-cspf — Local CSPF fallback is configured |
Metric |
The cost of the TE path for the LSP |
Local Sr Protection |
The local LFA protection wanted for the CSPF computed explicit path with adjacency SIDs |
Label Stack Reduction |
The label stack reduction applied to the CSPF computed explicit path with adjacency SIDs |
Load Bal Wt |
The load balance weight value |
Include Grps |
The included groups. None indicates that no groups are included |
Exclude Grps |
The excluded groups. None indicates that no groups are excluded |
Egress Stats |
The traffic statistics for the specified SR-TE LSP or for all SR-TE LSPs if none is explicitly specified. Traffic statistics are provided for primary path, secondary path, if any, and secondary standby paths, if any. Statistics are preserved across switch over for primary and secondary standby paths |
BFD Template |
The BFD template name |
BFD Ping Intvl |
The BFD ping interval |
BFD Enable |
The operational state of the BFD on the LSP |
BFD Failure-action |
The failure action that is configured for the BFD LSP |
WaitForUpTimer |
The BFD wait for up timer value |
ReturnPathLabel |
The return path label added to the MPLS label to the bottom of the label stack for S-BFD. With this configured, the S-BFD packet returns to the initiator through the MPLS return path |
Revert Timer |
The length of time before a named LSP using the secondary path to revert to the primary path |
Next Revert In |
The next revert interval |
Entropy Label |
The enabled or disabled status for the entropy label |
Oper Entropy Label |
Indicates that the entropy label is in use |
Negotiated EL |
Indicates if the entropy label is negotiated for the LSP |
Override Tunnel ELC |
The enabled or disabled status of the override tunnel ELC |
VPRNAutoBind |
The enabled or disabled status for VRPN autobind |
IGP Shortcut |
The enabled or disabled status for IGP shortcut |
BGP Shortcut |
The enabled or disabled status for BGP shortcut |
IGP LFA |
The enabled or disabled status for IGP LFA |
BGPTransTun |
The enabled or disabled status for BGP transport tunnels |
Oper Metric |
The enabled or disabled status of the operational metric |
PCE Report |
The enabled or disabled status of PCE report |
PCE Control |
The enabled or disabled status of PCE control |
Max SR Labels |
The maximum label stack size of the computed path with or without label stack reduction |
Additional FRR Labels |
The additional FRR labels value that the router is configured to take into account during TI-LFA |
Path Profile |
The path profile value for the LSP |
Admin Tags | The administrative tag names. None indicates that there are no tags. |
Primary (a) |
The preferred path for the LSP |
Up Time |
The total time in increments that the LSP path has been operational |
Bandwidth |
The amount of bandwidth in Mb/s reserved for the LSP path |
Secondary |
The alternate path that the LSP uses if the primary path is not available |
Downtime |
The time that the LSP has been down |
Bandwidth |
The amount of bandwidth in Mb/s reserved for the LSP path |
*A:Dut-C# /show router mpls sr-te-lsp path detail
===============================================================================
MPLS SR-TE LSP
Path (Detail)
===============================================================================
Legend :
S - Strict L - Loose
A-SID - Adjacency SID N-SID - Node SID
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
LSP SR-TE to_A_SR_TE
Path path_A
-------------------------------------------------------------------------------
LSP Name : to_A_SR_TE
Path LSP ID : 3072
From : 3.3.3.3
To : 1.1.1.1
Admin State : Up Oper State : Up
Path Name : path_A
Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:01:11 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 2 sec
Retry Attempt : 0 Next Retry In : 0 sec
PathCompMethod : none OperPathCompMethod: none
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : N/A
LabelStackRed : Disabled Oper LabelStackRed: N/A
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper SetupPriority: 7
Hold Priority : 0 Oper HoldPriority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper IncludeGroups:
None None
Exclude Groups : Oper ExcludeGroups:
None None
Last Resignal : n/a
IGP/TE Metric : 16777215 Oper Metric : 16777215
Oper MTU : 1496 Path Trans : 1
Degraded : False
Failure Code : noError
Failure Node : n/a
Explicit Hops :
No Hops Specified
Actual Hops :
1.1.1.1(1.1.1.1)(N-SID) Record Label : 19410
BFD Configuration and State
Template : srte Ping Interval : N/A
Enable : True State : up
ReturnPathLabel : 35001
WaitForUpTimer : 4 sec OperWaitForUpTimer: 4 sec
WaitForUpTmLeft : 0
StartFail Rsn : N/A
-------------------------------------------------------------------------------
LSP SR-TE to_A_SR_TE
Path path_A2
-------------------------------------------------------------------------------
LSP Name : to_A_SR_TE
Path LSP ID : 3074
From : 3.3.3.3
To : 1.1.1.1
Admin State : Up Oper State : Up
Path Name : path_A2
Path Type : Secondary
Path Admin : Up Path Oper : Down
Path Up Time : 0d 00:00:00 Path Down Time : 0d 00:01:53
Retry Limit : 0 Retry Timer : 2 sec
Retry Attempt : 0 Next Retry In : 0 sec
PathCompMethod : none OperPathCompMethod: N/A
MetricType : igp Oper MetricType : N/A
LocalSrProt : preferred Oper LocalSrProt : N/A
LabelStackRed : Disabled Oper LabelStackRed: N/A
Bandwidth : No Reservation Oper Bandwidth : N/A
Hop Limit : 255 Oper HopLimit : N/A
Setup Priority : 7 Oper SetupPriority: N/A
Hold Priority : 0 Oper HoldPriority : N/A
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper IncludeGroups:
None N/A
Exclude Groups : Oper ExcludeGroups:
None N/A
Last Resignal : n/a
IGP/TE Metric : N/A Oper Metric : N/A
Oper MTU : N/A Path Trans : 0
Degraded : False
Failure Code : noError
Failure Node : n/a
Explicit Hops :
No Hops Specified
Actual Hops :
No Hops Specified
Srlg : Disabled Srlg Disjoint : False
BFD Configuration and State
Template : srte Ping Interval : N/A
Enable : True State : notApplicable
ReturnPathLabel : 35002
WaitForUpTimer : 4 sec OperWaitForUpTimer: 4 sec
WaitForUpTmLeft : 0
StartFail Rsn : N/A
-------------------------------------------------------------------------------
LSP SR-TE template-1.1.1.1-671747
Path path_A
-------------------------------------------------------------------------------
LSP Name : template-1.1.1.1-671747
Path LSP ID : 14336
From : 30.30.2.2
To : 1.1.1.1
Admin State : Up Oper State : Up
Path Name : path_A
Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:01:12 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 0 Next Retry In : 0 sec
PathCompMethod : none OperPathCompMethod: none
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : N/A
LabelStackRed : Disabled Oper LabelStackRed: N/A
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 2 Oper HopLimit : 2
Setup Priority : 7 Oper SetupPriority: 7
Hold Priority : 0 Oper HoldPriority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper IncludeGroups:
None None
Exclude Groups : Oper ExcludeGroups:
None None
Last Resignal : n/a
IGP/TE Metric : 16777215 Oper Metric : 16777215
Oper MTU : 1496 Path Trans : 1
Degraded : False
Failure Code : noError
Failure Node : n/a
Explicit Hops :
No Hops Specified
Actual Hops :
30.30.2.1(1.1.1.1)(A-SID) Record Label : 524282
BFD Configuration and State
Template : None Ping Interval : N/A
Enable : False State : up
ReturnPathLabel : None
WaitForUpTimer : 4 sec OperWaitForUpTimer: 4 sec
WaitForUpTmLeft : 0
StartFail Rsn : N/A
Label |
Description |
---|---|
LSP Name |
The name of the LSP |
Path LSP ID |
The path LSP ID |
From |
The IP address for the ingress router for the LSP |
To |
The IP address for the egress router for the LSP |
Admin State |
The administrative state of the LSP |
Oper State |
The operational state of the LSP |
Path Name |
The name of the LSP path |
Path Type |
The type of LSP path |
Path Admin |
The administrative state of the LSP path |
Path Oper |
The operational state of the LSP path |
Path Up Time |
The length of time the LSP path has been operational |
Path Down Time |
The length of time the LSP path has been down |
Retry Limit |
The number of attempts that the software makes to reestablish the path after it has failed |
Retry Timer |
The time, in seconds, for path reestablishment attempts after LSP failure |
Retry Attempt |
The number of retry attempts |
Next Retry In |
The next retry value |
PathCompMethod |
The path computation method for the specific LSP pce — PCE path computation method is configured local-cspf — Local CSPF path computation method is configured none — No computation method is configured |
OperPathCompMethod |
The operational state of the path computation method pce — PCE path computation method is configured local-cspf — Local CSPF path computation method is configured none — No computation method is configured |
MetricType |
The cost of the TE path for the specific LSP |
Oper MetricType |
The operational state of cost of the TE path |
LocalSrProt |
The local LFA protection for the CSPF computed explicit path with adjacency SIDs |
Oper LocalSrProt |
The operational state of LFA protection for the CSPF computed explicit path with adjacency SIDs |
LabelStackRed |
The label stack reduction applied to the CSPF computed explicit path with adjacency SIDs |
Oper LabelStackRed |
The operational state of the label stack reduction applied to the CSPF computed explicit path with adjacency SIDs |
Bandwidth |
The amount of bandwidth in Mb/s to be reserved |
Oper Bandwidth |
The operational state of the bandwidth |
Hop Limit |
The maximum number of hops for the path |
Oper HopLimit |
The operational state of the maximum number of hops for the path |
Setup Priority |
The setup priority value to use for the path |
Oper SetupPriority |
The operational state of the setup priority value for the path |
Hold Priority |
The hold priority to use for the path |
Oper HoldPriority |
The operational state of the hold priority for the path |
PCE Report |
The enabled or disabled status of PCE report |
Oper PCE Report |
The operational state of the PCE report |
PCE Control |
The enabled or disabled status of PCE control |
Oper PCE Control |
The operational state of PCE control |
Include Groups |
The included groups. None indicates that no groups are included |
Oper IncludeGroups |
The operational state of the included groups |
Exclude Groups |
The excluded groups. None indicates that no groups are included |
Oper ExcludeGroups |
The operational state of the excluded groups |
Oper MTU |
The largest service frame size that can be transmitted to the far-end router without requiring the packet to be fragmented |
Failure Code | The reason code for in-progress MBB value. A value of none indicates that no failure has occurred. |
Failure Node | The IP address of the node in the LSP path at which the in-progress MBB failed. When no failure has occurred this value is none. |
Explicit Hops |
The explicit configured hops for an LSP path |
Actual Hops |
The actual hops an LSP path takes |
Record Label |
The record label value |
Template |
Indicates if the BFD template configured |
Ping Interval |
The BFD ping interval value |
Enable |
Indicates if BFD is enabled |
State |
The state of BFD |
ReturnPathLabel |
The return path label to add to the MPLS label on the bottom of the label stack for S-BFD. When configured, the S-BFD packet returns to the initiator through the MPLS return path. |
WaitForUpTimer |
The BFD wait for up timer value |
OperWaitForUpTimer |
The operational state of the wait for up timer value |
WaitForUpTmLeft |
The length of time remaining for the wait for up timer |
The following outputs apply to an SR-TE auto-LSP for which the path is computed by the hop-to-label translation method.
*A:Phoenix 199# show router mpls sr-te-lsp "sr-te-level2-mesh-192.168.48.223-
716805" detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : sr-te-level2-mesh-192.168.48.223-716805
LSP Type : MeshP2PSrTe LSP Tunnel ID : 61444
LSP Index : 126979 TTM Tunnel Id : 716805
From : 192.168.48.199 To : 192.168.48.2*
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:02:12 LSP Down Time : 0d 00:00:00
Transitions : 3 Path Changes : 3
Retry Limit : 0 Retry Timer : 30 sec
PathCompMethod : none
FallbkComp : not-applicable
Metric : N/A Use TE metric : Disabled
Include Grps : Exclude Grps :
None None
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 16777215
PCE Report : Enabled
PCE Control : Disabled
Max SR Labels : 8 Additional FRR Labels: 2
Path Profile :
None
Primary(a) : loose-anycast-sid Up Time : 0d 00:02:12
Bandwidth : 0 Mbps
===============================================================================
*A:Phoenix 199# show router mpls sr-te-lsp "sr-te-level2-mesh-192.168.48.223-
716805" path detail
===============================================================================
MPLS SR-TE LSP sr-te-level2-mesh-192.168.48.223-716805 Path (Detail)
===============================================================================
Legend :
S - Strict L - Loose
A-SID - Adjacency SID N-SID - Node SID
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
SR-TE LSP sr-te-level2-mesh-192.168.48.223-716805 Path loose-anycast-sid
-------------------------------------------------------------------------------
LSP Name : sr-te-level2-mesh-192.168.48.223-716805
Path LSP ID : 20480
From : 192.168.48.199 To : 192.168.48.223
Admin State : Up Oper State : Up
Path Name : loose-anycast-sid Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 02:30:28 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 1 Next Retry In : 0 sec
PathCompMethod : local-cspf OperPathCompMethod : local-cspf
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed: : Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper Setup Priority : 7
Hold Priority : 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Enabled Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper Include Groups :
None None
Exclude Groups : Oper Exclude Groups :
None None
IGP/TE Metric : 16777215 Oper Metric : 16777215
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops :
192.168.48.99(L)
Actual Hops :
192.168.48.99 (192.168.48.185)(N-SID) Record Label : 200099
-> 192.168.48.223 (192.168.48.223)(N-SID) Record Label : 200323
===============================================================================
*A:Phoneix 199# show router mpls sr-te-lsp
- sr-te-lsp [<lsp-name>] [status {up|down}] [detail] path [<path-name>]
[auto-lsp {all|mesh-p2p-srte|one-hop-p2p-srte}]
- sr-te-lsp [<lsp-name>] [detail] [auto-lsp {all|mesh-p2p-srte|
one-hop-p2p-srte}]
- sr-te-lsp [<lsp-name>] [status {up|down}] [to <ip-address>] [detail]
[auto-lsp {all|mesh-p2p-srte|one-hop-p2p-srte}]
<lsp-name> : [64 chars max]
<up|down> : up|down
<ip-address> : a.b.c.d
<detail> : keyword
<path> : keyword
<path-name> : [32 chars max]
<all|mesh-p2p-srte*> : keyword - specify type of auto-lsp
*A:Phoneix 199# show router mpls sr-te-lsp auto-lsp all
===============================================================================
MPLS Auto SR-TE LSPs (Originating)
===============================================================================
LSP Name To Tun Protect Adm Opr
Id Path
-------------------------------------------------------------------------------
sr-te-level2-mesh-192.168.48.221- 192.168.48.221 61443 N/A Up Up
716804
sr-te-level2-mesh-192.168.48.223- 192.168.48.223 61444 N/A Up Up
716805
-------------------------------------------------------------------------------
LSPs : 2
===============================================================================
*A:Phoneix 199# show router mpls sr-te-lsp auto-lsp mesh-p2p-srte
===============================================================================
MPLS Auto SR-TE LSPs (Originating)
===============================================================================
LSP Name To Tun Protect Adm Opr
Id Path
-------------------------------------------------------------------------------
sr-te-level2-mesh-192.168.48.221- 192.168.48.221 61443 N/A Up Up
716804
sr-te-level2-mesh-192.168.48.223- 192.168.48.223 61444 N/A Up Up
716805
-------------------------------------------------------------------------------
LSPs : 2
===============================================================================
Output Example
The following output is an example of SR-TE LSP count statistics.
===============================================================================
MPLS SR-TE LSP Count
===============================================================================
Total IpV4 IpV6
-------------------------------------------------------------------------------
SR-TE LSPs 0 0 0
Mesh SR-TE LSPs 0 0 0
One Hop SR-TE LSPs 0 0 0
PCE Init SR-TE LSPs 0 0 0
===============================================================================
MPLS SR-TE LSP Output Fields describes the MPLS SR-TE LSP count statistics output fields.
Label |
Description |
---|---|
LSP Name |
The name of the LSP used in the path. |
Adm State |
Down — The path is administratively disabled. Up — The path is administratively enabled. |
PathCompMethod |
pce — PCE path computation method is configured. local-cspf — Local CSPF path computation method is configured. |
FallbkPathComp |
none — No fallback method is configured. local-cspf — Local CSPF fallback is configured. |
Retry Limit |
The number of attempts that the software should make to reestablish the LSP after it has failed. |
Hop Limit |
The maximum number of hops that an LSP can traverse, including the ingress and egress routers. |
Retry Timer |
The time in seconds, for LSP re-establishment attempts after an LSP failure. |
LSP Up Time |
The total time in increments that the LSP path has been operational. |
LSP Down Time |
The total time in increments that the LSP path has not been operational. |
SR-TE LSPs |
Displays the number of SR-TE LSPs |
Mesh SR-TE LSPs |
Displays the number of mesh SR-TE LSPs |
One Hop-P2P SR-TE LSPs |
Displays the number of one-hop SR-TE LSPs |
PCE Init SR-TE LSPs |
Displays the number of PCE initiated SR-TE LSPs |
The following outputs apply to a router-controlled or to a PCC-controlled SR-TE LSP for which the path is computed using the hop-to-label transition method.
*A:Dut-A# show router mpls sr-te-lsp "srTeRtrControlled" path "1" detail
=======================================================================
MPLS SR-TE LSP srTeRtrControlled Path 1 (Detail)
=======================================================================
Legend :
S - Strict L - Loose
=======================================================================
-----------------------------------------------------------------------
SR-TE LSP srTeRtrControlled Path 1
-----------------------------------------------------------------------
LSP Name : srTeRtrControlled
Path LSP ID : 1024
From : 10.20.1.1 To : 10.20.1.6
Admin State : Up Oper State : Up
Path Name : 1 Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:03:19 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 1 Next Retry In : 0 sec
PathCompMethod : pce OperPathCompMethod : pce
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed : disabled Oper LabelStackRed : disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper Setup Priority : 7
Hold Priority : 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Inherited Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper Include Groups :
None None
Exclude Groups : Oper Exclude Groups :
None None
IGP/TE Metric : 16777215 Oper Metric : 16777215
Oper MTU : 1484 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops :
10.20.1.2(S) -> 10.20.1.3(L)
Actual Hops :
10.10.1.2 (10.20.1.2) Record Label : 262143
-> 10.20.1.3 (10.20.1.3) Record Label : 102003
-> 10.20.1.6 (10.20.1.6) Record Label : 103006
=======================================================================
*A:Dut-A# show router mpls sr-te-lsp "srTeRtrControlled" detail
=======================================================================
MPLS SR-TE LSPs (Originating) (Detail)
=======================================================================
-----------------------------------------------------------------------
Type : Originating
-----------------------------------------------------------------------
LSP Name : srTeRtrControlled
LSP Type : SrTeLsp LSP Tunnel ID : 2
LSP Index : 65537 TTM Tunnel Id : 655363
From : 10.20.1.1 To : 10.20.1.6
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:06:09 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Hop Limit : 255 Negotiated MTU : 1484
PathCompMethod : none
FallbkPathComp : not-applicable
Metric : N/A
Include Grps : Exclude Grps :
None None
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 16777215
PCE Report : Inherited Max SR Labels : 6
PCE Control : Disabled
Path Profile:
None
Primary(a) : 1 Up Time : 0d 00:06:09
Bandwidth : 0 Mbps
=======================================================================
Outputs with other filters:
---------------------------
*A:Dut-A# show router mpls sr-te-lsp
===============================================================================
MPLS SR-TE LSPs (Originating)
===============================================================================
LSP Name To Tun Protect Adm Opr
Id Path
-----------------------------------------------------------------------
sr-te1 10.20.1.6 1 N/A Up Up
srTeRtrControlled 10.20.1.6 2 N/A Up Up
-----------------------------------------------------------------------
LSPs : 2
=======================================================================
*A:Dut-A# show router mpls sr-te-lsp path
=======================================================================
MPLS SR-TE LSP Path
=======================================================================
-----------------------------------------------------------------------
LSP Name : sr-te1 To : 10.20.1.6
Adm State : Up Oper State : Up
-----------------------------------------------------------------------
Path Name Type Adm Opr
-----------------------------------------------------------------------
1 Primary Up Up
-----------------------------------------------------------------------
LSP Name : srTeRtrControlled To : 10.20.1.6
Adm State : Up Oper State : Up
-----------------------------------------------------------------------
Path Name Type Adm Opr
-----------------------------------------------------------------------
1 Primary Up Up
=======================================================================
*A:Dut-A# show router mpls sr-te-lsp to 10.20.1.6
=======================================================================
MPLS SRTE LSPs (Originating)
=======================================================================
LSP Name To Tun Protect Adm Opr
Id Path
-----------------------------------------------------------------------
sr-te1 10.20.1.6 1 N/A Up Up
srTeRtrControlled 10.20.1.6 2 N/A Up Up
-----------------------------------------------------------------------
LSPs : 2
=======================================================================
*A:Dut-A# show router mpls sr-te-lsp status up
=======================================================================
MPLS SR-TE LSPs (Originating)
=======================================================================
LSP Name To Tun Protect Adm Opr
Id Path
-----------------------------------------------------------------------
sr-te1 10.20.1.6 1 N/A Up Up
srTeRtrControlled 10.20.1.6 2 N/A Up Up
-----------------------------------------------------------------------
LSPs : 2
=======================================================================
*A:Dut-A# show router mpls sr-te-lsp "srTeRtrControlled" status up detail path "1"
=======================================================================
MPLS SR-TE LSP srTeRtrControlled Path 1 (Detail)
=======================================================================
Legend :
S - Strict L - Loose
=======================================================================
-----------------------------------------------------------------------
SR-TE LSP srTeRtrControlled Path 1
-----------------------------------------------------------------------
LSP Name : srTeRtrControlled
Path LSP ID : 1024
From : 10.20.1.1 To : 10.20.1.6
Admin State : Up Oper State : Up
Path Name : 1 Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:07:12 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 1 Next Retry In : 0 sec
PathCompMethod : none
FallbkPathComp : not-applicable
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper Setup Priority : 7
Hold Priority : 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Inherited Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper Include Groups :
None None
Exclude Groups : Oper Exclude Groups :
None None
IGP/TE Metric : 16777215 Oper Metric : 16777215
Oper MTU : 1484 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops :
10.20.1.2(S) -> 10.20.1.3(L)
Actual Hops :
10.10.1.2 (10.20.1.2) Record Label : 262143
-> 10.20.1.3 (10.20.1.3) Record Label : 102003
-> 10.20.1.6 (10.20.1.6) Record Label : 103006
=======================================================================
Output Example
The following outputs apply to PCE-computed SR-TE LSPs.
*A:Dut-B>config>router>mpls>lsp# /show router mpls sr-te-lsp "srte_lsp" path detail
===============================================================================
MPLS SR-TE LSP srte_lsp Path (Detail)
===============================================================================
Legend :
S - Strict L - Loose
===============================================================================
-------------------------------------------------------------------------------
SR-TE LSP srte_lsp Path fully_loose
-------------------------------------------------------------------------------
LSP Name : srte_lsp
Path LSP ID : 2
From : 10.20.1.2 To : 10.20.1.5
Admin State : Up Oper State : Up
Path Name : fully_loose Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 10:48:05 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 1 Next Retry In : 0 sec
PathCompMethod : pce OperPathCompMethod : pce
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed : Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper Setup Priority : 7
Hold Priority : 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Enabled Oper PCE Report : Enabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper Include Groups :
None None
Exclude Groups : Oper Exclude Groups :
None None
IGP/TE Metric : 20 Oper Metric : 20
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops :
No Hops Specified
Actual Hops :
192.168.2.1 Record Label : 131071
-> 192.168.5.5 Record Label : 131068
===============================================================================
*A:Dut-B>config>router>mpls>lsp# /show router mpls sr-te-lsp "srte_lsp" detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : srte_lsp
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 10.20.1.2 To : 10.20.1.5
Adm State : Up Oper State : Up
LSP Up Time : 0d 10:48:17 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Hop Limit : 255 Negotiated MTU : 1492
PathCompMethod : pce
FallbkPathComp : none
Metric : N/A Use TE metric : Disabled
Include Grps : Exclude Grps :
None None
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 20
PCE Report : Enabled
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile :
None
Primary(a) : fully_loose Up Time : 0d 10:48:17
Bandwidth : 0 Mbps
===============================================================================
Output Example
The following outputs apply to a PCE-computed SR-TE LSP when pce-report sr-te is enabled under MPLS.
*A:Dut-B>config>router>mpls>lsp# /show router mpls sr-te-lsp "srte_lsp" path detail
===============================================================================
MPLS SR-TE LSP srte_lsp Path (Detail)
===============================================================================
Legend :
S - Strict L - Loose
===============================================================================
-------------------------------------------------------------------------------
SR-TE LSP srte_lsp Path fully_loose
-------------------------------------------------------------------------------
LSP Name : srte_lsp
Path LSP ID : 2
From : 10.20.1.2 To : 10.20.1.5
Admin State : Up Oper State : Up
Path Name : fully_loose Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 10:51:47 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 1 Next Retry In : 0 sec
PathCompMethod : pce OperPathCompMethod: : pce
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed : Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper Setup Priority : 7
Hold Priority : 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Inherited Oper PCE Report : Enabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Groups : Oper Include Groups :
None None
Exclude Groups : Oper Exclude Groups :
None None
IGP/TE Metric : 20 Oper Metric : 20
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops :
No Hops Specified
Actual Hops :
192.168.2.1 Record Label : 131071
-> 192.168.5.5 Record Label : 131068
===============================================================================
*A:Dut-B>config>router>mpls>lsp# /show router mpls sr-te-lsp "srte_lsp" detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : srte_lsp
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 10.20.1.2 To : 10.20.1.5
Adm State : Up Oper State : Up
LSP Up Time : 0d 10:52:16 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Hop Limit : 255 Negotiated MTU : 1492
PathCompMethod : pce
FallbkPathComp : none
Metric : N/A Use TE metric : Disabled
Include Grps : Exclude Grps :
None None
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 20
PCE Report : Inherited
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile :
None
Primary(a) : fully_loose Up Time : 0d 10:52:16
Bandwidth : 0 Mbps
===============================================================================
Output Example
The following outputs apply to PCE-controlled SR-TE LSPs.
*A:Dut-B>config>router>pcep>pcc# /show router mpls sr-te-lsp "srte_lsp" path detail
=============================================================================
MPLS SR-TE LSP srte_lsp Path (Detail)
=============================================================================
Legend :
S - Strict L - Loose
=============================================================================
-----------------------------------------------------------------------------
SR-TE LSP srte_lsp Path fully_loose
-----------------------------------------------------------------------------
LSP Name : srte_lsp
Path LSP ID : 2
From : 10.20.1.2 To : 10.20.1.5
Admin State : Up Oper State : Up
Path Name : fully_loose Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:01:07 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt : 1 Next Retry In : 0 sec
PathCompMethod : pce OperPathCompMethod: : pce
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed : Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priority : 7 Oper Setup Priority : 7
Hold Priority : 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail Code: noError
PCE Report : Enabled Oper PCE Report : Enabled
PCE Control : Enabled Oper PCE Control : Enabled
Include Groups : Oper Include Groups :
None None
Exclude Groups : Oper Exclude Groups :
None None
IGP/TE Metric : 20 Oper Metric : 20
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops :
No Hops Specified
Actual Hops :
192.168.2.1 Record Label : 131071
-> 192.168.5.5 Record Label : 131068
=============================================================================
*A:Dut-B>config>router>pcep>pcc# /show router mpls sr-te-lsp "srte_lsp" detail
=============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
=============================================================================
-----------------------------------------------------------------------------
Type : Originating
-----------------------------------------------------------------------------
LSP Name : srte_lsp
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 10.20.1.2 To : 10.20.1.5
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:01:38 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Hop Limit : 255 Negotiated MTU : 1492
PathCompMethod : pce
FallbkPathComp : none
Metric : N/A Use TE metric : Disabled
Include Grps : Exclude Grps :
None None
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 20
PCE Report : Enabled
PCE Control : Enabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile :
None
Primary(a) : fully_loose Up Time : 0d 00:01:38
Bandwidth : 0 Mbps
=============================================================================
*A:Dut-B>config>router>mpls>lsp# /show router pcep pcc lsp-db
=============================================================================
PCEP Path Computation Client (PCC) LSP Update Info
=============================================================================
PCEP-specific LSP ID: 3
LSP ID : 2 LSP Type : seg-rt
Tunnel ID : 1 Extended Tunnel Id : 10.20.1.2
LSP Name : srte_lsp::fully_loose
Source Address : 10.20.1.2 Destination Address : 10.20.1.5
LSP Delegated : True Delegate PCE Address: 10.20.1.24
Oper Status : active
=============================================================================
*A:Dut-B>config>router>mpls>lsp# /show router mpls sr-te-lsp "srte_lsp" path
=============================================================================
MPLS SR-TE LSP srte_lsp Path
=============================================================================
-----------------------------------------------------------------------------
LSP Name : srte_lsp To : 10.20.1.5
Adm State : Up Oper State : Up
-----------------------------------------------------------------------------
Path Name Type Adm Opr
-----------------------------------------------------------------------------
fully_loose Primary Up Up
=============================================================================
Output Example
The following output applies to SR-TE LSP path statistics.
*A:Dut-C# show router mpls sr-te-lsp path family ipv6 status up
===============================================================================
MPLS SR-TE LSP Path
===============================================================================
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
To : 3ffe::a14:106
Adm State : Up Oper State : Up
-------------------------------------------------------------------------------
Path Name Type Adm Opr
-------------------------------------------------------------------------------
pe1_pe2 Primary Up Up
pe1_pe2_Stby Standby Up Up
===============================================================================
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106"
===============================================================================
MPLS SR-TE LSPs (Originating)
===============================================================================
LSP Name Tun Protect Adm Opr
To Id Path
-------------------------------------------------------------------------------
3ffe::a14:106 1 N/A Up Up
3ffe::a14:106
-------------------------------------------------------------------------------
LSPs : 1
===============================================================================
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106" detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
Legend :
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 3ffe::a14:103
To : 3ffe::a14:106
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:05:11 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Hop Limit : 255 Negotiated MTU : 1492
PathCompMethod : none
FallbkPathComp : not-applicable
Metric : N/A
Local Sr Protec*: preferred Label Stack Reduction: Disabled
Load Bal Wt : N/A ClassForwarding : Disabled
Include Grps : Exclude Grps :
None None
Egress Stats : Disabled
BFD Template : None BFD Ping Intvl : N/A
BFD Enable : False BFD Failure-action : None
WaitForUpTimer : 4
Revert Timer : Disabled Next Revert In : N/A
Entropy Label : Enabled+ Oper Entropy Label : Enabled
Negotiated EL : Disabled
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 16777215
PCE Report : Disabled+
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile : None
Admin Tags : None
Primary(a) : pe1_pe2
Up Time : 0d 00:05:13
Bandwidth : 0 Mbps
Secondary : pe1_pe2_Sec
Down Time : 0d 00:01:23
Bandwidth : 0 Mbps
Standby : pe1_pe2_Stby
Up Time : 0d 00:01:09
Bandwidth : 0 Mbps
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106" path
===============================================================================
MPLS SR-TE LSP 3ffe::a14:106 Path
===============================================================================
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
To : 3ffe::a14:106
Adm State : Up Oper State : Up
-------------------------------------------------------------------------------
Path Name Type Adm Opr
-------------------------------------------------------------------------------
pe1_pe2 Primary Up Up
pe1_pe2_Sec Secondary Up Dwn
pe1_pe2_Stby Standby Up Up
===============================================================================
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106" path detail
===============================================================================
MPLS SR-TE LSP 3ffe::a14:106 Path (Detail)
===============================================================================
Legend :
S - Strict L - Loose
A-SID - Adjacency SID N-SID - Node SID
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
LSP SR-TE 3ffe::a14:106
Path pe1_pe2
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
Path LSP ID : 59904
From : 3ffe::a14:103
To : 3ffe::a14:106
Admin State : Up Oper State : Up
Path Name : pe1_pe2 Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:09:24 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt: 0 Next Retry In : 0 sec
PathCompMeth*: none Oper PathCompMethod : none
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed: Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priori*: 7 Oper Setup Priority : 7
Hold Priority: 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail : noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Grou*: Oper Include Groups :
None None
Exclude Grou*: Oper Exclude Groups :
None None
Last Resignal: n/a
IGP/TE Metric: 16777215 Oper Metric : 16777215
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops:
3ffe::a14:101(L)
-> 3ffe::a14:106(L)
Actual Hops :
3ffe::a14:101
(3ffe::a14:101)(N-SID)
Record Label : 454488
3ffe::a14:106
-> (3ffe::a14:106)(N-SID)
Record Label : 424493
BFD Configuration and State:
Template : None Ping Interval : N/A
Enable : False State : notApplicable
WaitForUpTim*: 4 OperWaitForUpTimer : 0
WaitForUpTmL*: 0
Start Fail Reason: N/A
-------------------------------------------------------------------------------
LSP SR-TE 3ffe::a14:106
Path pe1_pe2_Sec
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
Path LSP ID : 59906
From : 3ffe::a14:103
To : 3ffe::a14:106
Admin State : Up Oper State : Up
Path Name : pe1_pe2_Sec Path Type : Secondary
Path Admin : Up Path Oper : Down
Path Up Time : 0d 00:00:00 Path Down Time : 0d 00:05:35
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt: 0 Next Retry In : 0 sec
PathCompMeth*: none Oper PathCompMethod : N/A
MetricType : igp Oper MetricType : N/A
LocalSrProt : preferred Oper LocalSrProt : N/A
LabelStackRed: Disabled Oper LabelStackRed : N/A
Bandwidth : No Reservation Oper Bandwidth : N/A
Hop Limit : 255 Oper HopLimit : N/A
Setup Priori*: 7 Oper Setup Priority : N/A
Hold Priority: 0 Oper Hold Priority : N/A
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail : noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Grou*: Oper Include Groups :
None N/A
Exclude Grou*: Oper Exclude Groups :
None N/A
Last Resignal: n/a
IGP/TE Metric: N/A Oper Metric : N/A
Oper MTU : N/A Path Trans : 2
Failure Code : noError
Failure Node : n/a
Explicit Hops:
3ffe::a14:102(L)
-> 3ffe::a14:106(L)
Actual Hops :
No Hops Specified
Srlg : Disabled Srlg Disjoint : False
BFD Configuration and State:
Template : None Ping Interval : N/A
Enable : False State : notApplicable
WaitForUpTim*: 4 OperWaitForUpTimer : 0
WaitForUpTmL*: 0
Start Fail Reason: N/A
-------------------------------------------------------------------------------
LSP SR-TE 3ffe::a14:106
Path pe1_pe2_Stby
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
Path LSP ID : 59908
From : 3ffe::a14:103
To : 3ffe::a14:106
Admin State : Up Oper State : Up
Path Name : pe1_pe2_Stby Path Type : Standby
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:05:21 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt: 0 Next Retry In : 0 sec
PathCompMeth*: none Oper PathCompMethod : none
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed: Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priori*: 7 Oper Setup Priority : 7
Hold Priority: 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail : noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Grou*: Oper Include Groups :
None None
Exclude Grou*: Oper Exclude Groups :
None None
Last Resignal: n/a
IGP/TE Metric: 16777215 Oper Metric : 16777215
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops:
3ffe::a14:102(L)
-> 3ffe::a14:106(L)
Actual Hops :
3ffe::a14:102
(3ffe::a14:102)(N-SID)
Record Label : 454489
3ffe::a14:106
-> (3ffe::a14:106)(N-SID)
Record Label : 439493
Srlg : Disabled Srlg Disjoint : False
BFD Configuration and State:
Template : None Ping Interval : N/A
Enable : False State : notApplicable
WaitForUpTim*: 4 OperWaitForUpTimer : 0
WaitForUpTmL*: 0
Start Fail Reason: N/A
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106" status up detail path "pe1_pe2"
family ipv6
===============================================================================
MPLS SR-TE LSP 3ffe::a14:106 Path pe1_pe2 (Detail)
===============================================================================
Legend :
S - Strict L - Loose
A-SID - Adjacency SID N-SID - Node SID
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
LSP SR-TE 3ffe::a14:106
Path pe1_pe2
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
Path LSP ID : 59904
From : 3ffe::a14:103
To : 3ffe::a14:106
Admin State : Up Oper State : Up
Path Name : pe1_pe2 Path Type : Primary
Path Admin : Up Path Oper : Up
Path Up Time : 0d 00:16:20 Path Down Time : 0d 00:00:00
Retry Limit : 0 Retry Timer : 30 sec
Retry Attempt: 0 Next Retry In : 0 sec
PathCompMeth*: none Oper PathCompMethod : none
MetricType : igp Oper MetricType : igp
LocalSrProt : preferred Oper LocalSrProt : preferred
LabelStackRed: Disabled Oper LabelStackRed : Disabled
Bandwidth : No Reservation Oper Bandwidth : 0 Mbps
Hop Limit : 255 Oper HopLimit : 255
Setup Priori*: 7 Oper Setup Priority : 7
Hold Priority: 0 Oper Hold Priority : 0
Inter-area : N/A
PCE Updt ID : 0 PCE Updt State : None
PCE Upd Fail : noError
PCE Report : Disabled+ Oper PCE Report : Disabled
PCE Control : Disabled Oper PCE Control : Disabled
Include Grou*: Oper Include Groups :
None None
Exclude Grou*: Oper Exclude Groups :
None None
Last Resignal: n/a
IGP/TE Metric: 16777215 Oper Metric : 16777215
Oper MTU : 1492 Path Trans : 1
Failure Code : noError
Failure Node : n/a
Explicit Hops:
3ffe::a14:101(L)
-> 3ffe::a14:106(L)
Actual Hops :
3ffe::a14:101
(3ffe::a14:101)(N-SID)
Record Label : 454488
3ffe::a14:106
-> (3ffe::a14:106)(N-SID)
Record Label : 424493
BFD Configuration and State:
Template : None Ping Interval : N/A
Enable : False State : notApplicable
WaitForUpTim*: 4 OperWaitForUpTimer : 0
WaitForUpTmL*: 0
Start Fail Reason: N/A
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106" activepath
===============================================================================
MPLS LSP: 3ffe::a14:106 (active paths)
===============================================================================
Legend :
# - Manually switched path
#F - Manually forced switched path
===============================================================================
LSP Name : 3ffe::a14:106
LSP Id : 59904
Path Name : pe1_pe2
Active Path : Primary
To : 3ffe::a14:106
LSP Type : SR-TE
===============================================================================
*A:Dut-C>config>router>mpls# show router mpls sr-te-lsp "3ffe::a14:106" egress-stats
===============================================================================
SR-TE LSP Egress Statistics
===============================================================================
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
-------------------------------------------------------------------------------
Admin State : Up
Path Name : pe1_pe2
StatsOperState : Up
Aggregate Pkts : 0 Aggregate Octets : 0
Path Name : pe1_pe2_Sec
StatsOperState : Up
Aggregate Pkts : 0 Aggregate Octets : 0
Path Name : pe1_pe2_Stby
StatsOperState : Up
Aggregate Pkts : 0 Aggregate Octets : 0
Total for all paths
Tot.Aggr Pkts : 0 Tot.Aggr Octets : 0
===============================================================================
*A:Dut-C# show router mpls sr-te-lsp "3ffe::a14:106" to 3ffe::a14:106 detail
===============================================================================
MPLS SR-TE LSPs (Originating) (Detail)
===============================================================================
Legend :
+ - Inherited
===============================================================================
-------------------------------------------------------------------------------
Type : Originating
-------------------------------------------------------------------------------
LSP Name : 3ffe::a14:106
LSP Type : SrTeLsp LSP Tunnel ID : 1
LSP Index : 65536 TTM Tunnel Id : 655362
From : 3ffe::a14:103
To : 3ffe::a14:106
Adm State : Up Oper State : Up
LSP Up Time : 0d 00:50:36 LSP Down Time : 0d 00:00:00
Transitions : 1 Path Changes : 1
Retry Limit : 0 Retry Timer : 30 sec
Hop Limit : 255 Negotiated MTU : 1492
PathCompMethod : none
FallbkPathComp : not-applicable
Metric : N/A
Local Sr Protec*: preferred Label Stack Reduction: Disabled
Load Bal Wt : N/A ClassForwarding : Disabled
Include Grps : Exclude Grps :
None None
Egress Stats : Disabled
BFD Template : None BFD Ping Intvl : N/A
BFD Enable : False BFD Failure-action : None
WaitForUpTimer : 4
Revert Timer : Disabled Next Revert In : N/A
Entropy Label : Enabled+ Oper Entropy Label : Enabled
Negotiated EL : Disabled
VprnAutoBind : Enabled
IGP Shortcut : Enabled BGP Shortcut : Enabled
IGP LFA : Disabled IGP Rel Metric : Disabled
BGPTransTun : Enabled
Oper Metric : 16777215
PCE Report : Disabled+
PCE Control : Disabled
Max SR Labels : 6 Additional FRR Labels: 1
Path Profile : None
Admin Tags : None
Primary(a) : pe1_pe2
Up Time : 0d 00:50:39
Bandwidth : 0 Mbps
Secondary : pe1_pe2_Sec
Down Time : 0d 00:46:48
Bandwidth : 0 Mbps
Standby : pe1_pe2_Stby
Up Time : 0d 00:46:34
Bandwidth : 0 Mbps
===============================================================================
* indicates that the corresponding row element may have been truncated.
Output Example
The following output applies to SR-TE LSP egress statistics.
*A:Dut-B>config>router>mpls>lsp# /show router mpls sr-te-lsp "lsp1" egress-stats
===============================================================================
SR-TE LSP Egress Statistics
===============================================================================
-------------------------------------------------------------------------------
LSP Name : lsp1
-------------------------------------------------------------------------------
Admin State : Up
Path Name : p1
StatsOperState : Up
Aggregate Pkts : 0 Aggregate Octets : 0
Path Name : p2
StatsOperState : Up
Aggregate Pkts : 0 Aggregate Octets : 0
Total for all paths
Tot.Aggr Pkts : 0 Tot.Aggr Octets : 0
Packet Rate pps : 0 Bit Rate Mbps : 0
===============================================================================
Output Fields: MPLS SR-TE LSP Egress Statistics describes the MPLS SR-TE LSP egress statistics output fields.
Label |
Description |
---|---|
LSP Name |
The name of the LSP for which the statistics are provided |
Admin State |
The administrative state of the LSP |
Path Name |
The path name of the LSP |
StatsOperState |
Indicates whether the system is able to allocate a statistical index to that specific path |
Aggregate Pkts |
The number of packets recorded by the statistical index for that path |
Aggregate Octets |
The number of octets recorded by the statistical index for that path |
Tot.Aggr Pkts |
The sum of packets over all paths of the LSP |
Tot.Aggr Octets |
The sum of octets over all paths of the LSP |
Packet Rate |
The packet rate for the LSP (across all paths, for all FCs in/out-of profile) expressed in packets per second |
Bit Rate |
The bit rate for the LSP (across all paths, for all FCs in/out-of profile) expressed in Mb/s |
sr-te-lsp-egress-stats
sr-te-lsp-egress-stats
Syntax
sr-te-lsp-egress-stats lsp-name
Context
[Tree] (clear>router>mpls sr-te-lsp-egress-stats)
Full Context
clear router mpls sr-te-lsp-egress-stats
Description
This command clears or resets the egress statistics for MPLS SR-TE LSP.
Parameters
- lsp-name
-
Specifies the LSP to clear, up to 64 characters.
Platforms
All
sr-te-lsp-egress-stats
Syntax
sr-te-lsp-egress-stats lsp lsp-name [interval seconds] [repeat repeat] [ absolute| rate] [bits ]
Context
[Tree] (monitor>router>mpls sr-te-lsp-egress-stats)
Full Context
monitor router mpls sr-te-lsp-egress-stats
Description
This command monitors MPLS SR-TE LSP Egress Statistics.
Parameters
- lsp-name
-
Specifies the LSP name.
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
- bits
-
Displays output value in bits.
Platforms
All
src-access-list
src-access-list
Syntax
src-access-list [list-name]
Context
[Tree] (show>system>security>snmp src-access-list)
Full Context
show system security snmp src-access-list
Description
This command displays source access lists and the hosts for each. Including the list-name parameter modifies the output show only the specified src-access-list.
Platforms
All
Output
The following output is an example of SR access list information.
Show Source Access List Output Fields describes the source access list output fields.
Output ExampleA:ALA-1# show system security snmp src-access-list
=============================================================================
Source Access Lists
=============================================================================
List Name
HostName Host Address
-----------------------------------------------------------------------------
L1
H1 10.100.100.1
H2 10.100.100.2
L2
HA 10.100.101.1
HB 10.100.101.2
-----------------------------------------------------------------------------
Total Access Lists: 2
=============================================================================
A:ALA-1#
A:ALA-1# show system security snmp src-access-list L1
=============================================================================
Source Access Lists
=============================================================================
List Name
HostName Host Address
-----------------------------------------------------------------------------
L1
H1 10.100.100.1
H2 10.100.100.2
-----------------------------------------------------------------------------
Total Access Lists: 1
=============================================================================
A:ALA-1#
Label |
Description |
---|---|
List Name |
Displays the name of the src-access-list. |
Host Name |
Displays the name of the src-host. |
Host Address |
Displays the IP address of the src-host. |
Total Access Lists |
Displays the total number of source access lists. |
src-bmac-lsb
src-bmac-lsb
Syntax
src-bmac-lsb
Context
[Tree] (tools>dump>redundancy src-bmac-lsb)
Full Context
tools dump redundancy src-bmac-lsb
Description
This command dumps PBB source Backbone MAC address LSB information.
Platforms
All
srlg-database
srlg-database
Syntax
srlg-database [router-id ip-address] [interface ip-address]
Context
[Tree] (show>router>mpls srlg-database)
Full Context
show router mpls srlg-database
Description
This command displays MPLS SRLG database information.
Parameters
- router-id ip-address
-
Specifies a 32-bit integer uniquely identifying the router in the Autonomous System. By convention to ensure uniqueness, this may default to the value of one of the router's IPv4 host addresses, represented as a 32-bit unsigned integer, if IPv4 is configured on the router. The router-id can be either the local one or some remote router.
- interface ip-address
-
Specifies the IP address of the interface.
Platforms
All
srlg-group
srlg-group
Syntax
srlg-group [name]
Context
[Tree] (show>router>if-attribute srlg-group)
Full Context
show router if-attribute srlg-group
Description
This command displays SRLG statistics.
Parameters
- name
-
Displays entries that are associated with the specified SRLG name, up to 32 characters.
Platforms
All
Output
The following output is an example of SRLG statistics, and SRLG Fields describes the fields.
Output ExampleB:CORE2# show router if-attribute srlg-group
==================================================
Interface Srlg Groups
==================================================
Group Name Group Value Penalty Weight
--------------------------------------------------
1 1 100
2 2 200
3 3 300
--------------------------------------------------
No. of Groups: 3
==================================================
B:CORE2#
Label |
Description |
---|---|
Group Name |
The name of the SRLG |
Group Value |
The integer value of the SRLG |
Penalty Weight |
The penalty weight that is assigned to the SRLG |
No. of Groups |
The total number of displayed SRLGs |
srrp
srrp
Syntax
srrp
Context
[Tree] (clear>router srrp)
Full Context
clear router srrp
Description
Commands in this context clear and reset SRRP virtual router instances.
Platforms
All
srrp
Syntax
srrp [srrp-id [detail]]
Context
[Tree] (show srrp)
Full Context
show srrp
Description
This command displays information related to the SRRP.
Parameters
- srrp-id
-
Specifies the SRRP ID.
- detail
-
Displays detailed information.
Platforms
All
srrp-sync-database
srrp-sync-database
Syntax
srrp-sync-database [instance instance-id] [ peer ip-address]
Context
[Tree] (tools>dump>redundancy>multi-chassis srrp-sync-database)
Full Context
tools dump redundancy multi-chassis srrp-sync-database
Description
This command dumps SRRP database information and applies to the 7450 ESS.
Parameters
- ip-address
-
Specifies the peer’s IP address.
- instance-id
-
Dumps information for the specified Subscriber Router Redundancy Protocol instance configured on this system.
Platforms
All
ssh
ssh
Syntax
ssh
Context
[Tree] (show>system>security ssh)
Full Context
show system security ssh
Description
This command displays all the SSH sessions, and the SSH status and fingerprint. The type of SSH application (CLI, SCP, SFTP, or NETCONF) is indicated for each SSH connection.
Platforms
All
Output
The following output is an example of SSH information, and Show System Security SSH Options Output Fields describes the output fields.
Output Example*A:dut-b# show system security ssh
=======================================================
SSH Server
=======================================================
Administrative State : Enabled
Operational State : Up
Preserve Key : Enabled
SSH Protocol Version 2 : Enabled
DSA Host Key Fingerprint : 0f:10:a3:ca:ff:22:d0:90:6e:2b:90:57:f1:5b:0a:92
RSA Host Key Fingerprint : b3:2b:ba:1b:ef:49:68:dc:b5:ff:b9:55:b7:78:e9:ee
-------------------------------------------------------
Connection Username
Version Cipher ServerName Status
-------------------------------------------------------
192.0.2.131 admin
2 aes128-ctr cli connected
-------------------------------------------------------
Number of SSH sessions : 1
=======================================================
Label |
Description |
---|---|
SSH Administrative State |
Enabled — The administrative state of the SSH server is enabled Disabled — The administrative state of the SSH server is disabled |
SSH Operational State |
Up — The operational state of the SSH server is up Down — The operational state of the SSH server is down |
SSH Preserve Key |
Enabled — preserve-key is enabled Disabled — preserve-key is disabled |
SSH Protocol Version 2 |
Enabled — SSH2 is enabled Disabled — SSH2 is disabled |
Key Fingerprint |
The key fingerprint is the server identity If a client attempts and fails to verify the key fingerprint of the server, the client session is disconnected. |
Connection |
The IP address of the connected routers (remote client) |
Encryption |
des — data encryption using a private (secret) key 3des — an encryption method that allows proprietary information to be transmitted over untrusted networks |
Username |
The name of the user |
Number of SSH Sessions |
The total number of active SSH sessions |
ssid
ssid
Syntax
ssid
Context
[Tree] (show>subscr-mgmt>wlan-gw ssid)
Full Context
show subscriber-mgmt wlan-gw ssid
Description
This command displays SSID information.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
ssm-translate
ssm-translate
Syntax
ssm-translate
ssm-translate interface interface-name
Context
[Tree] (show>router>igmp ssm-translate)
Full Context
show router igmp ssm-translate
Description
This command displays IGMP SSM translate configuration information.
Parameters
- interface-name
-
Specifies the IP interface name, up to 32 characters.
Platforms
All
Output
The following output is an example of SSM translate information. IGMP Fields provides IGMP field descriptions.
Output Example=================================================================
IGMP SSM Translate Entries
=================================================================
Group Range Source Interface
-----------------------------------------------------------------
<239.1.1.1 - 239.1.1.2> 10.1.1.1 -
<239.1.1.1 - 239.1.1.5> 00.1.1.2 ies-abc
-----------------------------------------------------------------
Label |
Description |
---|---|
Group Range |
The address ranges of the multicast groups for which this router can be an RP. |
Source |
The unicast address that sends data on an interface. |
SSM Translate Entries |
The total number of SSM translate entries. |
ssm-translate
Syntax
ssm-translate
ssm-translate interface interface-name
Context
[Tree] (show>router>mld ssm-translate)
Full Context
show router mld ssm-translate
Description
This command displays MLD SSM translate configuration information.
Parameters
- interface-name
-
Specifies the IP interface name, up to 32 characters.
Platforms
All
Output
MLD Interface Output
The following table provides MLD field descriptions.
Label |
Description |
---|---|
Start Address End Address |
The address ranges of the multicast groups for which this router can be an RP. |
Source Address |
The unicast address that sends data on an interface. |
Interface |
The interface name. |
SSM Translate Entries |
The total number of SSM translate entries. |
*A:ALA-BA# show router mld static
===============================================================================
MLD SSM Translate Entries
===============================================================================
Start Address : ff0e::db8:9
End Address : ff0e::db8:c
Source Address : 2001:db8::1
Start Address : ff04:db8:2
End Address : ff04:db8:10
Source Address : 2001:db8:3:4:5:6:7:8
Interface : lax-vls
Start Address : ff0e:db8:db8:9
End Address : ff0e:db8:db8:c
Source Address : 2001:db8::1
Interface : lax-vls
-------------------------------------------------------------------------------
SSM Translate Entries : 3
===============================================================================
*A:ALA-BA#
standby
standby
Syntax
standby
Context
[Tree] (show>system>ptp standby)
Full Context
show system ptp standby
Description
This command displays information for PTP on the standby control module.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e, 7750 SR-2s, 7750 SR-2se, 7750 SR-7s, 7750 SR-14s, 7950 XRS
Output
The following output is an example of PTP standby information.
Output Example# show system ptp standby
===============================================================================
IEEE 1588/PTP Clock Information
===============================================================================
-------------------------------------------------------------------------------
Local Clock
-------------------------------------------------------------------------------
Clock Type : boundary PTP Profile : ITU-T G.8275.1
Domain : 24 Network Type : sdh
Admin State : up Oper State : up
Announce Interval : 8 pkt/s Announce Rx Timeout: 3 intervals
Peer Limit : none (Base Router)
G.8275 Priority : 128 PTSF-unusable : disabled
Clock Id : a47b2cfffe441e1f Clock Class : 165
Clock Accuracy : unknown Clock Variance : ffff (not computed)
Clock Priority1 : 128 Clock Priority2 : 128
-------------------------------------------------------------------------------
Parent Clock
-------------------------------------------------------------------------------
Port : 1/1/3 Remote MAC Address : a4:7b:2c:e2:f1:a2
Parent Clock Id : 242124fffe49e335 Remote PTP Port : 1
GM Clock Id : 242124fffe49e335 GM Clock Class : 6
GM Clock Accuracy : within 100 ns GM Clock Variance : 0x4e5d (1.8E-15)
GM Clock Priority1: 128 GM Clock Priority2 : 128
-------------------------------------------------------------------------------
Time Properties
-------------------------------------------------------------------------------
Timescale : PTP
Frequency Traceable : yes
Time Traceable : yes
Time Source : GPS
UTC Offset : +37 seconds
Leap Second : no leap second pending
-------------------------------------------------------------------------------
Frequency Recovery
-------------------------------------------------------------------------------
PTP Recovery State: initial Last Changed : 2021/09/02 11:04:48
Frequency Offset : -367.370 ppb
===============================================================================
standby-ip-addresses
standby-ip-addresses
Syntax
standby-ip-addresses
Context
[Tree] (show>subscr-mgmt>vrgw>brg>gateway standby-ip-addresses)
Full Context
show subscriber-mgmt vrgw brg gateway standby-ip-addresses
Description
This command shows associated home-aware pool standby IP addresses.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
start
start
Syntax
start
Context
[Tree] (tools>perform>router>l2tp>group>tunnel start)
Full Context
tools perform router l2tp group tunnel start
Description
This command triggers an attempt to start the control connection for a specified L2TP tunnel.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
start
Syntax
start route-downloader-name [force]
Context
[Tree] (tools>perform>aaa>route-downloader start)
Full Context
tools perform aaa route-downloader start
Description
This command causes the download process to start immediately. If an ongoing download is already in progress then no further action is needed, except if the force keyword is added. In case the force keyword is added, then the current download is aborted and a new one is immediately restarted. If aborting the current download, the internal route table should not be emptied or cleared.
Parameters
- route-downloader-name
-
Specifies the route downloader name, up to 32 characters.
- force
-
Causes the current download to be aborted and a new one is immediately restarted.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
static
static
Syntax
static [sap sap-id | sdp sdp-id:vc-id]
Context
[Tree] (show>service>id>mld-snooping static)
Full Context
show service id mld-snooping static
Description
This command displays MLD snooping static group membership data.
Platforms
All
Output
The following output is an example of MLD snooping static group membership information.
Output Example*A:rbae_C# show service id 1 mld-snooping static
===============================================================================
MLD Snooping Static Source Groups for service 1
-------------------------------------------------------------------------------
MLD Snooping Static Source Groups for SDP 36:1
-------------------------------------------------------------------------------
Source
Group
-------------------------------------------------------------------------------
2011:db8:1
FF04:db8:2
*
FF04:db8:3
-------------------------------------------------------------------------------
Static (*,G)/(S,G) entries: 2
===============================================================================
*A:rbae_C#
static
Syntax
static [sap sap-id | sdp sdp-id:vc-id]
Context
[Tree] (show>service>id>igmp-snooping static)
Full Context
show service id igmp-snooping static
Description
This command displays information on static IGMP snooping source groups for the VPLS service.
Parameters
- sap sap-id
-
Displays static IGMP snooping source groups for a specific SAP.
- sdp sdp-id
-
Displays the IGMP snooping source groups for a specific spoke or mesh SDP.
- vc-id
-
The virtual circuit ID on the SDP ID for which to display information.
Platforms
All
Output
Output Example*A:ALA-1>show>service>id>snooping# static
===============================================================================
IGMP Snooping Static Source Groups for SAP 1/1/2
-------------------------------------------------------------------------------
Source Group
-------------------------------------------------------------------------------
* 239.0.0.2
* 239.0.0.3
-------------------------------------------------------------------------------
Static (*,G)/(S,G) entries: 2
-------------------------------------------------------------------------------
IGMP Snooping Static Source Groups for SDP 10:10
-------------------------------------------------------------------------------
Source Group
-------------------------------------------------------------------------------
1.1.1.1 239.0.0.10
-------------------------------------------------------------------------------
Static (*,G)/(S,G) entries: 1
===============================================================================
*A:ALA-1>show>service>id>snooping#
IGMP Snooping Source Groups Fields describes the show output fields.
Label |
Description |
---|---|
Source |
Displays the IP source address used in IGMP queries. |
Group |
Displays the static IGMP snooping source groups for a specified SAP. |
static
Syntax
static [ip-int-name | ip-address]
Context
[Tree] (show>router>igmp static)
Full Context
show router igmp static
Description
This command displays static IGMP, (*,G) and (S,G) information.
Parameters
- ip-int-name
-
Displays information associated with the specified IP interface name, up to 32 characters.
- ip-address
-
Displays information associated with the specified IP address.
Platforms
All
Output
The following output is an example of IGMP static information. IGMP Static Fields provides static IGMP field descriptions.
Output Example*A:ALA-BA# show router 100 igmp static
==================================================================
IGMP Static Group Source
==================================================================
Source Group Interface
------------------------------------------------------------------
10.11.11.11 239.136.22.3 IGMP_to_CE
* 239.1.1.1 IGMP_to_CE
10.22.22.22 239.255.255.255 IGMP_to_CE
------------------------------------------------------------------
Static (*,G)/(S,G) Entries : 3
==================================================================
*A:ALA-BA#
Label |
Description |
---|---|
Source |
Entries that represent a source address from which receivers are interested/not interested in receiving multicast traffic. |
Group |
The IP multicast group address for which this entry contains information. |
Interface |
Displays the interface name. |
static
Syntax
static [ip-int-name | ip-address]
Context
[Tree] (show>router>mld static)
Full Context
show router mld static
Description
This command displays static MLD, (*,G) and (S,G) information.
Parameters
- ip-int-name
-
Displays the information associated with the specified IP interface name.
- ip-address
-
Displays the information associated with the specified IP address.
Platforms
All
Output
The following output is an example of MLD static information. MLD Static Fields provides static MLD field descriptions.
Output Example*A:ALA-BA# show router mld static
===============================================================================
Rtr Base MLD Static Group Sources
===============================================================================
Source Interface
Group Start [Group Step]
[Group End] [Group Count]
-------------------------------------------------------------------------------
2001:db8:2016:10ff::4 lax-vls
ff05:db8:1
* lax-vls
ff06:db8:1
* lax-vls
ff01:db8:1 ::4:0
ff01:db8:100:0 64
3::1 lax-vls
ff05:db8:1 ::1
ff05:db8:20 32
* lax-vls
ff05:db8:2:1 ::1
ff05:db8:2:3ff 1023
3::1 lax-vls
ff05:db8:3:0 ::64
ff05:db8:4:0 656
3::2 lax-vls
ff05:db8:3:0 ::64
ff05:db8:4:0 656
4::1 flax-vlsoo
ff05:db8:3:0 ::64
ff05:db8:4:0 656
5::1 lax-vls
ff05:db8:3:0 ::64
ff05:db8:4:0 656
-------------------------------------------------------------------------------
Static (*,G)/(S,G) Entries : 9
===============================================================================
*A:ALA-BA#
Label |
Description |
---|---|
Source |
The entries which represents a source address from which receivers are interested/not interested in receiving multicast traffic. |
Group |
The IP multicast group address for which this entry contains information. |
Interface |
The interface name. |
static
Syntax
static [head-end {local | ip-address}] [ color color] [end-point { ipv4-address | ipv6-address}] [preference preference-id] [distinguisher distinguisher-id]
static summary
Context
[Tree] (show>router>seg-rt>sr-policies static)
Full Context
show router segment-routing sr-policies static
Description
This command displays the traffic statistics of all or a filtered set of the static policies, or displays summary parameters.
Parameters
- head-end local
-
Filters on local head end.
- head-end ip-address
-
Filters on the head end IP address value.
- color
-
Filters on the color.
- ipv4-address | ipv6-address
-
Filters on the end-point IPv4 or IPv6 address.
- preference-id
-
Filters on the preference ID.
- distinguisher-id
-
Filters on the distinguisher ID.
- summary
-
Displays the summary information of the static policies.
Platforms
All
Output
The following output is an example of traffic statistics for the static policies.
Output Example Information for Static Policies *A:Dut-C# show router segment-routing sr-policies static
===============================================================================
SR-Policies Path
===============================================================================
-------------------------------------------------------------------------------
Type : srv6
Active : Yes Owner : static
Color : 10
Head : 0.0.0.0 Endpoint Addr : 3ffe::a14:102
RD : 5 Preference : 14
SRv6 BSID 1 : 3333:3:3:3:0:b::
TunnelId : 917510 Age : 759
Origin ASN : 0 Origin : 0.0.0.0
NumReEval : 0 ReEvalReason : none
NumActPathChange: 0 Last Change : 06/13/2022 17:40:54
Maintenance Policy: N/A
Path Segment Lists:
Segment-List : 1 Weight : 1
S-BFD State : Down S-BFD Transitio*: 0
Num Segments : 1 Last Change : 06/10/2022 17:07:01
Seg 1 SID : 2222:2:2:2:0:a:: State : resolved-up
===============================================================================
* indicates that the corresponding row element may have been truncated.
Output Example Information for a Subset of Static
Policies
*A:Dut-C# show router segment-routing sr-policies static end-point 3ffe::a14:102
===============================================================================
SR-Policies Path
===============================================================================
-------------------------------------------------------------------------------
Type : srv6
Active : Yes Owner : static
Color : 10
Head : 0.0.0.0 Endpoint Addr : 3ffe::a14:102
RD : 5 Preference : 14
SRv6 BSID 1 : 3333:3:3:3:0:b::
TunnelId : 917510 Age : 426
Origin ASN : 0 Origin : 0.0.0.0
NumReEval : 0 ReEvalReason : none
NumActPathChange: 0 Last Change : 06/13/2022 17:40:54
Maintenance Policy: N/A
Path Segment Lists:
Segment-List : 1 Weight : 1
S-BFD State : Down S-BFD Transitio*: 0
Num Segments : 1 Last Change : 06/10/2022 17:07:01
Seg 1 SID : 2222:2:2:2:0:a:: State : resolved-up
===============================================================================
* indicates that the corresponding row element may have been truncated.
static-arp
static-arp
Syntax
static-arp [{ip-int-name | ip-address | mac ieee-mac-address}]
Context
[Tree] (show>router static-arp)
Full Context
show router static-arp
Description
This command displays the router static ARP table sorted by IP address. If no options are present, all ARP entries are displayed.
Parameters
- ip-int-name
-
Only displays static ARP entries associated with the specified IP interface name.
- ip-address
-
Only displays static ARP entries associated with the specified IP address.
- ieee-mac-address
-
Only displays static ARP entries associated with the specified MAC address.
Platforms
All
Output
Static ARP Table Output — The following output is an example of static AARP table information, and Static ARP Table Fields describes the output fields.
Output ExampleA:ALA-A# show router static-arp
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Age Type Interface
-------------------------------------------------------------------------------
10.200.0.253 00:00:5a:40:00:01 00:00:00 Sta to-ser1
10.200.1.1 00:00:5a:01:00:33 00:00:00 Inv to-ser1a
-------------------------------------------------------------------------------
No. of ARP Entries: 1
===============================================================================
A:ALA-A#
A:ALA-A# show router static-arp 10.200.1.1
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Age Type Interface
-------------------------------------------------------------------------------
10.200.1.1 00:00:5a:01:00:33 00:00:00 Inv to-ser1
===============================================================================
A:ALA-A#
A:ALA-A# show router static-arp to-ser1
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Age Type Interface
-------------------------------------------------------------------------------
10.200.0.253 00:00:5a:40:00:01 00:00:00 Sta to-ser1
===============================================================================
A:ALA-A#
A:ALA-A# show router static-arp mac 00:00:5a:40:00:01
===============================================================================
ARP Table
===============================================================================
IP Address MAC Address Age Type Interface
-------------------------------------------------------------------------------
10.200.0.253 00:00:5a:40:00:01 00:00:00 Sta to-ser1
===============================================================================
A:ALA-A#
Label |
Description |
---|---|
IP Address |
The IP address of the static ARP entry |
MAC Address |
The MAC address of the static ARP entry |
Age |
The age of the ARP entry. Static ARPs always have 00:00:00 for the age |
Type |
Inv — the ARP entry is an inactive static ARP entry (invalid) Sta — the ARP entry is an active static ARP entry |
Interface |
The IP interface name associated with the ARP entry |
No. of ARP Entries |
The number of ARP entries displayed in the list |
static-host
static-host
Syntax
static-host [sap sap-id] [wholesaler service-id] [port port-id][inter-dest-id intermediate-destination-id] [detail] [mac ieee-address] [ip-address ip-prefix[ /prefix-length]]
static-host [sap sap-id ][wholesaler service-id ][port port-id] no-inter-dest-id [ detail]
static-host summary
Context
[Tree] (show>service>id static-host)
Full Context
show service id static-host
Description
This command displays static hosts configured on this service.
Parameters
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- intermediate-destination-id
-
Specifies the intermediate destination identifier which is encoded in the identification strings up to 32 characters.
- summary
-
Displays summary static host information.
- detail
-
Displays detailed static host information.
- service-id
-
The service ID of the wholesaler.
- ieee-address
-
Specifies the MAC address.
- ip-prefix[/prefix-length]
-
Specifies the IP address.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of service static host information.
Output Example*A:ALA-48# show service id 88 static-host
===============================================================================
Static Hosts for service 88
===============================================================================
Sap IP Address Configured MAC Dynamic MAC
Subscriber Admin State Fwding State
-------------------------------------------------------------------------------
1/2/20:0 10.10.10.104 N/A N/A
N/A Down Not Fwding
3/2/4:50/5 10.144.145.1 N/A N/A
N/A Up Fwding
-------------------------------------------------------------------------------
Number of static hosts : 2
===============================================================================
*A:ALA-48#
static-lsp
static-lsp
Syntax
static-lsp [lsp-name]
static-lsp {transit | terminate}
static-lsp count
Context
[Tree] (show>router>mpls static-lsp)
Full Context
show router mpls static-lsp
Description
This command displays MPLS static LSP information.
Platforms
All
Output
The following output is an example of MPLS static LSP information.
MPLS Static LSP Output Fields describes the MPLS static LSP output fields.
Label |
Description |
---|---|
Lsp Name |
The name of the LSP used in the path up to 64 characters in length. |
To |
The system IP address of the egress router for the LSP. |
Next Hop |
The system IP address of the next hop in the LSP path. |
In I/F |
The ingress interface. |
Out Label |
The egress interface. |
Out I/F |
The egress interface. |
Adm |
Down — The path is administratively disabled. Up — The path is administratively enabled. |
Opr |
Down — The path is operationally down. Up — The path is operationally up. |
LSPs |
The total number of static LSPs. |
A:ALA-12# show router mpls static-lsp
===============================================================================
MPLS Static LSPs (Originating)
===============================================================================
Lsp Name To Next Hop Out Label Out I/F Adm Opr
-------------------------------------------------------------------------------
NYC_SJC_customer2 100.20.1.10 10.10.1.4 1020 1/1/1 Up Up
-------------------------------------------------------------------------------
LSPs : 1
===============================================================================
A:ALA-12#
*A:SRU4>config>router>mpls# show router mpls static-lsp transit
===============================================================================
MPLS Static LSPs (Transit)
===============================================================================
In Label In Port Out Label Out Port Next Hop Adm Opr
-------------------------------------------------------------------------------
240 aps-1 440 1/1/10 10.22.11.3 Up Up
241 aps-1 441 1/1/10 10.22.11.3 Up Up
242 aps-1 442 1/1/10 10.22.11.3 Up Up
243 aps-1 443 1/1/10 10.22.11.3 Up Up
244 aps-1 444 1/1/10 10.22.11.3 Up Up
245 aps-1 445 1/1/10 10.22.11.3 Up Up
246 aps-1 446 1/1/10 10.22.11.3 Up Up
247 aps-1 447 1/1/10 10.22.11.3 Up Up
248 aps-1 448 1/1/10 10.22.11.3 Up Up
249 aps-1 449 1/1/10 10.22.11.3 Up Up
250 aps-1 450 1/1/10 10.22.11.3 Up Up
251 aps-1 451 1/1/10 10.22.11.3 Up Up
252 aps-1 452 1/1/10 10.22.11.3 Up Up
253 aps-1 453 1/1/10 10.22.11.3 Up Up
...
207 3/2/8 407 1/1/9 10.22.10.3 Up Up
208 3/2/8 408 1/1/9 10.22.10.3 Up Up
209 3/2/8 409 1/1/9 10.22.10.3 Up Up
-------------------------------------------------------------------------------
LSPs : 256
===============================================================================
*A:SRU4>config>router>mpls#
A:ALA-12# show router mpls static-lsp terminate
===============================================================================
MPLS Static LSPs (Terminate)
===============================================================================
In Label In I/F Out Label Out I/F Next Hop Adm Opr
-------------------------------------------------------------------------------
1021 1/1/1 n/a n/a n/a Up Up
-------------------------------------------------------------------------------
LSPs : 1
===============================================================================
A:ALA-12#
static-policy
static-policy
Syntax
static-policy
static-policy name [detail]
Context
[Tree] (show>router>seg-rt>sr-policies static-policy)
Full Context
show router segment-routing sr-policies static-policy
Description
This command displays information about all static policies or the specified static policy.
Parameters
- name
-
Specifies the name of the static policy, up to 64 characters.
- detail
-
Displays detailed information about the static policy.
Platforms
All
Output
The following outputs are examples of information for a specified static policy.
Output Example Information for a Specific Static Policy*A:Dut-C# show router segment-routing sr-policies static-policy "a1"
===============================================================================
SR-Policies Static Policy
===============================================================================
Policy Name: a1
Type : srv6
Admin Status : Up Color : 10
Head End Addr : 0.0.0.0 Endpoint Addr : 3ffe::a14:102
Preference : 14
RD : 5
SRv6 BSID 1 : N/A
Locator : C1
Function : End.B6.Encaps.Red Function Value : -
Function Stat*: error
Segment Lists Configuration:
Segment-List : 1 Weight : 1
Admin Status : Up Last Change : 06/13/2022 17:40:54
Segment Stack:
SRv6 SID 1: 2222:2:2:2:0:a::
===============================================================================
* indicates that the corresponding row element may have been truncated.
Output Example Detailed Information for a Specific Static
Policy
*A:Dut-C# show router segment-routing sr-policies static-policy "a1" detail
===============================================================================
SR-Policies Static Policy
===============================================================================
Policy Name: a1
Type : srv6
Admin Status : Up Color : 10
Head End Addr : 0.0.0.0 Endpoint Addr : 3ffe::a14:102
Preference : 14
RD : 5
SRv6 BSID 1 : N/A
Locator : C1
Function : End.B6.Encaps.Red Function Value : -
Function Stat*: error
Path Entry:
Active : Yes Owner : static
TunnelId : 917510 Age : 346
Origin ASN : 0 Origin : 0.0.0.0
NumReEval : 0 ReEvalReason : none
NumActPathChange: 0 Last Change : 06/13/2022 17:40:54
Maintenance Policy: N/A
Path Segment Lists:
Segment-List : 1 Weight : 1
S-BFD State : Down S-BFD Transitio*: 0
Num Segments : 1 Last Change : 06/10/2022 17:07:01
Seg 1 SID : 2222:2:2:2:0:a:: State : resolved-up
===============================================================================
* indicates that the corresponding row element may have been truncated.
static-route
static-route
Syntax
static-route [family] [{ip-prefix/prefix-length | preference preference | [ next-hop ip-address | tag tag}] [ detail]
Context
[Tree] (show>router static-route)
Full Context
show router static-route
Description
This command displays the static entries in the routing table. If no options are present, all static routes are displayed sorted by prefix.
Parameters
- family
-
Specifies the type of routing information to be distributed by this peer group.
- ip-prefix/prefix-length
-
Displays static routes only matching the specified ip-prefix and mask.
- preference
-
Only displays static routes with the specified route preference.
- ip-address
-
Only displays static routes with the specified next hop IP address.
- tag
-
Displays the tag used to add a 32-bit integer tag to the static route. The tag is used in route policies to control distribution of the route into other protocols.
- detail
-
Displays detailed static routes information.
Platforms
All
Output
Static Route Output — The following output is an example of static route information, and Static Route Fields describes the fields.
Output ExampleA:ALA-A# show router static-route
===============================================================================
Route Table
===============================================================================
IP Addr/mask Pref Metric Type Nexthop Interface Active
-------------------------------------------------------------------------------
192.168.250.0/24 5 1 ID 10.200.10.1 to-ser1 Y
192.168.252.0/24 5 1 NH 10.10.0.254 n/a N
192.168.253.0/24 5 1 NH to-ser1 n/a N
192.168.253.0/24 5 1 NH 10.10.0.254 n/a N
192.168.254.0/24 4 1 BH black-hole n/a Y
===============================================================================
A:ALA-A#
A:ALA-A# show router static-route 192.168.250.0/24
===============================================================================
Route Table
===============================================================================
IP Addr/mask Pref Metric Type Nexthop Interface Active
-------------------------------------------------------------------------------
192.168.250.0/24 5 1 ID 10.200.10.1 to-ser1 Y
===============================================================================
A:ALA-A#
A:ALA-A# show router static-route preference 4
===============================================================================
Route Table
===============================================================================
IP Addr/mask Pref Metric Type Nexthop Interface Active
-------------------------------------------------------------------------------
192.168.254.0/24 4 1 BH black-hole n/a Y
===============================================================================
A:ALA-A#
A:ALA-A# show router static-route next-hop 10.10.0.254
===============================================================================
Route Table
===============================================================================
IP Addr/mask Pref Metric Type Nexthop Interface Active
-------------------------------------------------------------------------------
192.168.253.0/24 5 1 NH 10.10.0.254 n/a N
===============================================================================
A:ALA-A#
===============================================================================
Static Route Table (Router: Base) Family: IPv6
===============================================================================
Prefix : 3ffe::10:10:14:0/120
Nexthop : 3ffe::10:20:1:6
Type : Indirect
Interface : n/a Active : Y
Prefix List : n/a Prefix List Type : n/a
Metric : 1 Preference : 5
Source Class : 0 Dest Class : 0
Admin State : Up Tag : 0
Creation Origin : manual
BFD : disabled
Community :
CPE-check : disabled
Tunnel Resolution: any Disallow-IGP : disabled
RSVP-TE Tunnels : disabled LDP Tunnels : disabled
SR-ISIS Tunnels : disabled SR-OSPF Tunnels : disabled
SR-TE Tunnels : disabled
-------------------------------------------------------------------------------
Prefix : 3ffe::10:10:14:0/120
Nexthop : 3ffe::20:20:1:6
Type : Indirect
Interface : n/a Active : Y
Prefix List : n/a Prefix List Type : n/a
Metric : 1 Preference : 5
Source Class : 0 Dest Class : 0
Admin State : Up Tag : 0
Creation Origin : manual
BFD : disabled
Community :
CPE-check : disabled
Tunnel Resolution: any Disallow-IGP : disabled
RSVP-TE Tunnels : disabled LDP Tunnels : disabled
SR-ISIS Tunnels : disabled SR-OSPF Tunnels : disabled
SR-TE Tunnels : disabled
-------------------------------------------------------------------------------
Prefix : 3ffe::10:10:14:0/120
Nexthop : 3ffe::20:20:1:5
Type : Indirect
Interface : n/a Active : Y
Prefix List : n/a Prefix List Type : n/a
Metric : 1 Preference : 5
Source Class : 0 Dest Class : 0
Admin State : Up Tag : 0
Creation Origin : manual
BFD : disabled
Community :
CPE-check : disabled
Tunnel Resolution: any Disallow-IGP : disabled
RSVP-TE Tunnels : disabled LDP Tunnels : disabled
SR-ISIS Tunnels : disabled SR-OSPF Tunnels : disabled
SR-TE Tunnels : disabled
-------------------------------------------------------------------------------
Prefix : 3ffe::10:10:14:0/120
Nexthop : 3ffe::10:20:1:5
Type : Indirect
Interface : n/a Active : Y
Prefix List : n/a Prefix List Type : n/a
Metric : 1 Preference : 5
Source Class : 0 Dest Class : 0
Admin State : Up Tag : 0
Creation Origin : manual
BFD : disabled
Community :
CPE-check : disabled
Tunnel Resolution: filter Disallow-IGP : disabled
RSVP-TE Tunnels : disabled LDP Tunnels : disabled
SR-ISIS Tunnels : enabled SR-OSPF Tunnels : disabled
SR-TE Tunnels : disabled
-------------------------------------------------------------------------------
No. of Static Routes: 4
===============================================================================
*A:Dut-C#
A:Router#show router static-route 10.10.10.10/32 detail
===============================================================================
Static Route Table (Router: Base) Family: IPv4
===============================================================================
Prefix : 10.10.10.10/32
CommunityList : (Not Specified)
Tag : 0
Backup Tag : 0
Nexthop : 1.13.1.1 Validate Nexthop : No
Type : Nexthop
Backup Nexthop : 2.23.1.1 Backup Status : Active
Backup
Interface : Dut-C-Dut-A-1 Active : Y
Prefix List : n/a Prefix List Type : n/a
Metric : 1 Preference : 5
Source Class : 0 Dest Class : 0
Admin State : Up Nexthop Tag : 0
Creation Origin : manual Load Bal Weight : n/a
BFD : disabled
Nexthop Community:
CPE-check : disabled
LDP Sync : disabled
-------------------------------------------------------------------------------
No. of Static Routes: 1
===============================================================================
A:Router#
Label |
Description |
---|---|
IP Addr/mask |
The static route destination address and mask |
Pref |
The route preference value for the static route |
Metric |
The route metric value for the static route |
Type |
BH — the static route is a black hole route; the nexthop for this type of route is black-hole ID — the static route is an indirect route, where the nexthop for this type of route is the non-directly connected next hop NH — the route is a static route with a directly connected next-hop; the next-hop for this type of route is either the next-hop IP address or an egress IP interface name |
Nexthop |
The next hop for the static route destination |
Protocol |
The protocol through which the route was learned |
Interface |
The egress IP interface name for the static route n/a — indicates there is no current egress interface because the static route is inactive or a black hole route |
Active |
N — the static route is inactive; for example, the static route is disabled or the next hop IP interface is down Y — the static route is active |
No. of Routes |
The number of routes displayed in the list |
Backup Nexthop |
The backup next hop for the static route destination |
Backup Tag |
The tag value used for the static route when the primary next hop fails and the backup next hop is active |
Backup Status |
The status of the backup next hop |
static-route
Syntax
static-route ldp-sync-status
Context
[Tree] (tools>dump>router static-route)
Full Context
tools dump router static-route
Description
This command enables the synchronization status that static route keeps track of LDP interfaces.
Parameters
- ldp-sync-status
-
Specifies the LDP synchronization status.
Platforms
All
Output
The following output is an example of static route information.
Output Example*A:Dut-C# tools dump router static-route ldp-sync-status
===============================================================================
Sync Status of LDP interfaces
===============================================================================
If If Name Timer Running? Timeout Time
Index Yes/No Used Left
-------------------------------------------------------------------------------
2 ip-10.10.2.3 Yes 30 5
3 ip-10.10.3.3 No 30 0
4 ip-10.10.5.3 No 30 0
5 ip-10.10.22.3 No 30 0
6 ip-10.10.12.3 No 30 0
===============================================================================
static-sa
static-sa
Syntax
static-sa
static-sa name sa-name
static-sa spi spi
Context
[Tree] (show>ipsec static-sa)
Full Context
show ipsec static-sa
Description
This command displays IPsec static-SA information.
Parameters
- sa-name
-
Specifies the SA name.
- spi
-
Specifies the spi.
Platforms
All
station
station
Syntax
station [station-name]
Context
[Tree] (show>router>bmp station)
Full Context
show router bmp station
Description
This command displays BGP monitor (BMP) information.
Parameters
- station-name
-
Specifies the station name of a BMP monitoring station, up to 32 characters.
Platforms
All
Output
The following output is an example of BMP monitor information.
Output Example*A:Dut-C# show router bmp station
===============================================================================
BMP Stations (monitoring router "Base")
===============================================================================
Station Name Session State Since Msgs Sent
-------------------------------------------------------------------------------
lys ESTABLISHED 05/08/2018 15:32:12 103054
myr ESTABLISHED 05/08/2018 15:32:13 100007
-------------------------------------------------------------------------------
No. of BMP Stations: 2
===============================================================================
*A:Dut-C# show router bmp station "lys"
===============================================================================
BMP Station "lys" (monitoring router "Base")
===============================================================================
Admin State : enabled Global BMP State : enabled
Station Address : 100.3.7.7 Station Port : 12344
Via Router : Base TCP Auth Keychain:
Stats Report : 15 seconds Routes Report : 5 seconds
Connect Interval : 120 seconds Local Routes : reporting
Initiation Msg : Hello Station Lys
Reported families: ipv4
Session State : ESTABLISHED Last Change : 05/08/2018 15:32:12
Local Address : 100.3.7.3 Local Port : 51041
Stat Report Msgs : 3028 Route Report Msgs: 100021
Peer Up Msgs : 4 Peer Down Msgs : 0
Initiation Msgs : 1 Goodbye Msgs : 0
Bytes sent : 10926521
Stats Timer : 1 seconds left Routes Timer : 3 seconds left
Connect Timer : not running Monitored Peers : 3 of 4
Output queue : 0/50 Last Msg Sent : 05/15/2018 09:27:31
===============================================================================
*A:Dut-C#
station
Syntax
station station-name
station all
Context
[Tree] (clear>router>bmp station)
[Tree] (clear>service>id>bmp station)
Full Context
clear router bmp station
clear service id bmp station
Description
This command clears BMP station connections.
Parameters
- station-name
-
Specifies the BMP monitoring station name, up to 32 characters.
Platforms
All
station
Syntax
station [station-name]
Context
[Tree] (show>bmp station)
Full Context
show bmp station
Description
This command displays BMP station information.
Parameters
- station-name
-
Specifies the station name, up to 32 characters.
Platforms
All
statistics
statistics
Syntax
statistics [interface ip-int-name | ip-address]
Context
[Tree] (show>router>dhcp statistics)
Full Context
show router dhcp statistics
Description
This command displays statistics for DHCP Relay and DHCP snooping.
If no IP address or interface name is specified, all configured interfaces are displayed.
If an IP address or interface name is specified, only data regarding the specified interface is displayed.
Parameters
- ip-int-name | ip-address
-
Displays statistics for the specified IP interface.
Platforms
All
Output
The following command displays DHCP statistics information, and Show DHCP Statistics Field Descriptions describes the output fields.
show router dhcp statistics
Output Example
====================================================================
DHCP Global Statistics (Router: Base)
====================================================================
Rx Packets : 0
Tx Packets : 0
Rx Malformed Packets : 0
Rx Untrusted Packets : 0
Client Packets Discarded : 0
Client Packets Relayed : 0
Client Packets Snooped : 0
Client Packets Proxied (RADIUS) : 0
Client Packets Proxied (Diameter) : 0
Client Packets Proxied (User-Db) : 0
Client Packets Proxied (Lease-Split) : 0
Server Packets Discarded : 0
Server Packets Relayed : 0
Server Packets Snooped : 0
DHCP RELEASEs Spoofed : 0
DHCP FORCERENEWs Spoofed : 0
Client packets streamed : 0
Routed Subnet Transparent Forwarded
Client Packets (BOOTREQUEST) : 0
Server Packets (BOOTREPLY) : 0
Other Opcode Packets : 0
====================================================================
Label |
Description |
---|---|
Rx Packets |
The number of packets received from the DHCP clients |
Tx Packets |
The number of packets transmitted to the DHCP clients |
Rx Malformed Packets |
The number of malformed packets received from the DHCP clients |
Rx Untrusted Packets |
The number of untrusted packets received from the DHCP clients |
Client Packets Discarded |
The number of packets received from the DHCP clients that were discarded |
Client Packets Relayed |
The number of packets received from the DHCP clients that were forwarded |
Client Packets Snooped |
The number of packets received from the DHCP clients that were snooped |
Client Packets Proxied (RADIUS) |
The number of client packets proxied through RADIUS |
Client Packets Proxied (Diameter) |
The number of client packets proxied through Diameter |
Client Packets Proxied (User-Db) |
The number of client packets proxied through User-Db |
Client Packets Proxied (Lease-Split) |
The number of client packets proxied through a lease split |
Server Packets Discarded |
The number of packets received from the DHCP server that were discarded |
Server Packets Relayed |
The number of packets received from the DHCP server that were forwarded |
Server Packets Snooped |
The number of packets received from the DHCP server that were snooped |
DHCP RELEASEs Spoofed |
The number of spoofed DHCP releases |
DHCP FORCERENEWs Spoofed |
The number of spoofed FORCERENEW messages |
Client packets streamed |
The number of client packets streamed |
Routed Subnet Transparent Forwarded |
|
Client Packets (BOOTREQUEST) |
The number of DHCP client packets (BOOTREQUEST) received on a subscriber interface with the source IP in a routed subnet that is associated with a routed IPoE session or host. The routed-subnet-transparent-forwarding command must be configured in the routing instance. |
Server Packets (BOOTREPLY) |
The number of DHCP server packets (BOOTREPLY) received on a subscriber interface with the source IP in a routed subnet that is associated with a routed IPoE session or host. The routed-subnet-transparent-forwarding command must be configured in the routing instance. |
Other Opcode Packets |
The number of DHCP packets (Opcode field that are different from BOOTREQUEST and BOOTREPLY) received on a subscriber interface with the source IP in a routed subnet associated with a routed IPoE session or host. The routed-subnet-transparent-forwarding command must be configured in the routing instance. Note: When transparent forwarding is
enabled, the system does not check if the DHCP packet is
valid and therefore packets with an Opcode field
different from BOOTREQUEST and BOOTREPLY are
forwarded.
|
statistics
Syntax
statistics [interface ip-int-name]
Context
[Tree] (show>service>id>dhcp6 statistics)
[Tree] (show>router>dhcp6 statistics)
Full Context
show service id dhcp6 statistics
show router dhcp6 statistics
Description
This command displays statistics for DHCPv6 relay and snooping.
Parameters
- ip-int-name
-
Specifies to display interface name information.
Platforms
All
Output
The following output is an example of DHCP6 statistics information.
Output ExampleA:Dut-A# show service id 20 dhcp6 statistics
====================================================================
DHCP Statistics, service 20, all interfaces
====================================================================
Packets received : 0
Packets transmitted : 0
Packets dropped : 0
====================================================================
====================================================================
DHCP Statistics, service 21, all SAPs
====================================================================
Client packets snooped : 2
Client packets forwarded : 2
Client packets dropped : 19
Server packets snooped : 2
Server packets forwarded : 2
Server packets dropped : 0
====================================================================
A:Dut-A# show service id 1000 dhcp6 statistics
====================================================================
DHCP Statistics, service 1000, all interfaces
====================================================================
Packets received : 16063
Packets transmitted : 16061
Packets dropped : 0
====================================================================
====================================================================
DHCP Statistics, service 1000, all SAPs
====================================================================
Client packets snooped : 0
Client packets forwarded : 0
Client packets dropped : 0
Server packets snooped : 0
Server packets forwarded : 0
Server packets dropped : 0
====================================================================
DHCP6 Statistics Field Descriptions describes DHCP6 output statistics.
Field |
Description |
---|---|
Client Packets Dropped |
The number of DHCPv6 client packets snooped on SAP ingress and dropped, for example: DHCPv6 client packet received on an LDRA enabled network-facing SAP |
Client Packets Forwarded |
The number of DHCPv6 client packets snooped on SAP ingress and forwarded |
Client Packets Snooped |
The number of DHCPv6 client packets snooped on SAP ingress |
Server Packets Dropped |
The number of DHCPv6 server packets snooped on SAP ingress and dropped, for example: DHCPv6 server packet received on an LDRA enabled client-facing SAP |
Server Packets Forwarded |
The number of DHCPv6 server packets snooped on SAP ingress and forwarded |
Server Packets Snooped |
The number of DHCPv6 server packets snooped on SAP ingress |
statistics
Syntax
statistics [[sap sap-id] | [sdp sdp-id:vc-id] | [interface interface-name]]
Context
[Tree] (show>service>id>dhcp statistics)
Full Context
show service id dhcp statistics
Description
This command displays DHCP relay statistics.
Parameters
- ip-int-name
-
Displays DHCP statistics on the specified interface.
- interface-name
-
Displays DHCP statistics for the specified interface name.
- sap-id
-
Displays DHCP statistics for the specified SAP.
Platforms
All
Output
The following output is an example of DHCP statistics information.
Output Example*A:ALA-48# show service id 88 dhcp statistics interface SpokeTerm
===================================================================
DHCP Statistics for interface SpokeTerm
===================================================================
Rx Packets : 0
Tx Packets : 0
Rx Malformed Packets : 0
Rx Untrusted Packets : 0
Client Packets Discarded : 0
Client Packets Relayed : 0
Client Packets Snooped : 0
Client Packets Proxied (RADIUS) : 0
Client Packets Proxied (Lease-Split) : 0
Server Packets Discarded : 0
Server Packets Relayed : 0
Server Packets Snooped : 0
DHCP RELEASEs Spoofed : 0
DHCP FORCERENEWs Spoofed : 0
===================================================================
*A:ALA-48#
DHCP Statistics Field Descriptions describes DHCP statistics output fields.
Field |
Description |
---|---|
Rx Packets |
The number of received packets |
Tx Packets |
The number of transmitted packets |
Rx Malformed |
The number of malformed packets received |
Rx Untrusted Packets |
The number of untrusted packets received |
Client Packets Discarded |
The number of client packets discarded |
Client Packets Relayed |
The number of client packets relayed |
Client Packets Snooped |
The number of client packets snooped |
Client Packets Proxied (RADIUS) |
The number of client packets proxied through RADIUS |
Client Packets Proxied (Lease-Split) |
The number of client packets proxied through a lease split |
Server Packets Discarded |
The number of discarded server packets |
Server Packets Relayed |
The number of relayed server packets |
Server Packets Snooped |
The number of snooped server packets |
DHCP RELEASEs Spoofed |
The number of spoofed DHCP releases |
DHCP FORCERENEWs Spoofed |
The number of spoofed FORCERENEW messages |
statistics
Syntax
statistics
statistics interface {ip-int-name | ip-address}
statistics sap sap-id
Context
[Tree] (show>service>id>ppp statistics)
Full Context
show service id ppp statistics
Description
This command displays PPP statistics.
Parameters
- ip-int-name
-
Displays information about the specified interface, up to 32 characters.
- ip-address
-
Displays information about the specified IP address.
- sap-id
-
Displays information for the specified SAP.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
statistics frag-stats
statistics map-domain domain-name
Context
[Tree] (clear>nat>map statistics)
Full Context
clear nat map statistics
Description
This command clears MAP statistics.
Parameters
- domain-name
-
Clears MAP statistics for the specified domain name, up to 32 characters.
Platforms
VSR
statistics
Syntax
statistics [{ip-address | ip-int-name}]
Context
[Tree] (clear>router>dhcp statistics)
Full Context
clear router dhcp statistics
Description
This command clears statistics for DHCP statistics.
If no IP address or interface name is specified, then statistics are cleared for all configured interfaces.
If an IP address or interface name is specified, then only data regarding the specified interface is cleared.
Parameters
- ip-int-name
-
Clears DHCP statistics for the specified interface name.
- ip-address
-
Clears DHCP statistics for the specified IP address.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>router>dhcp6 statistics)
Full Context
clear router dhcp6 statistics
Description
This command clears DHCP6 statistics.
Platforms
All
statistics
Syntax
statistics
statistics interface ip-int-name | ipv6-address
statistics sap sap-id
Context
[Tree] (clear>service>id>dhcp6 statistics)
Full Context
clear service id dhcp6 statistics
Description
This command clears DHCPv6 statistics for interfaces and VPLS SAPs.
Parameters
- ip-int-name
-
Clears DHCPv6 statistics for the specified interface name.
- ipv6-address
-
Clears DHCPv6 statistics for the specified IP address.
- sap-id
-
Clears DHCPv6 statistics for the specified VPLS SAP.
Platforms
All
statistics
Syntax
statistics [{sap sap-id | sdp sdp-id:vc-id | interface { ip-address | ip-int-name}}]
Context
[Tree] (clear>service>id>dhcp statistics)
Full Context
clear service id dhcp statistics
Description
This command clears DHCP statistics.
Parameters
- sap-id
-
Clears the specified SAP information.
- sdp-id
-
The specified SDP to be cleared.
- vc-id
-
Specifies the virtual circuit ID on the SDP ID to be cleared.
- ip-address
-
Specifies the interface IP address.
- ip-int-name
-
Specifies the interface name, up to 32 characters.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>subscr-mgmt>gtp statistics)
Full Context
show subscriber-mgmt gtp statistics
Description
This command displays GTP statistics information.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of GTP statistics.
Output ExampleNode# show subscriber-mgmt gtp statistics
===============================================================================
GTP statistics
===============================================================================
tx echo requests : 23
tx echo responses : 0
tx errors : 0
rx echo requests : 0
rx echo responses : 23
rx errors : 0
rx version not supported : 0
rx zero TEID responses : 0
path faults : 0
path restarts : 0
tx invalid msgs : 0
tx create PDP context requests : 0
tx create PDP context responses : 0
tx delete PDP context requests : 0
tx delete PDP context responses : 0
tx create session requests : 0
tx create session responses : 1
tx delete session requests : 0
tx delete session responses : 0
tx delete bearer requests : 0
tx delete bearer responses : 0
tx create bearer responses : 0
tx update bearer responses : 0
tx modify bearer requests : 0
tx modify bearer responses : 1
tx change notification responses : 0
tx rls access bearers responses : 0
tx error indication count : 0
tx downlink notifications : 0
tx stop paging indication : 0
tx end marker : 0
rx invalid msgs : 0
rx create PDP context requests : 0
rx create PDP context responses : 0
rx delete PDP context requests : 0
rx delete PDP context responses : 0
rx create session requests : 1
rx create session responses : 0
rx delete session requests : 0
rx delete session responses : 0
rx delete bearer requests : 0
rx delete bearer responses : 0
rx create bearer requests : 0
rx update bearer requests : 0
rx modify bearer requests : 1
rx modify bearer responses : 0
rx change notification requests : 0
rx rls access bearers request : 0
rx error indication count : 0
rx downlink notification ack : 0
rx downlink notification fail : 0
rx invalid pkt length : 0
rx unknown pkts : 0
rx missing IE pkts : 0
rx bad UDP header pkts : 0
rx discarded pkts : 0
rx in-session discarded pkts : 0
rx pkts : 25
tx discarded pkts : 0
tx pkts : 25
rx UDP checksum error : 0
===============================================================================
statistics
Syntax
statistics
Context
[Tree] (show>router>l2tp statistics)
Full Context
show router l2tp statistics
Description
This command displays L2TP statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of L2TP statistics information.
Output Example*A:Dut-C# show router l2tp statistics
===============================================================================
L2TP Statistics
===============================================================================
Tunnels Sessions
-------------------------------------------------------------------------------
Active : 3 Active : 6
Setup history since 04/17/2009 18:38:41
Total : 4 Total : 9
Failed : 0 Failed : 0
Failed Auth : 0
===============================================================================
*A:Dut-C#
statistics
Syntax
statistics [{sap sap-id | interface ip-int-name | ip-address}]
Context
[Tree] (show>service>id>pppoe statistics)
Full Context
show service id pppoe statistics
Description
This command displays PPPoE statistics.
Parameters
- sap-id
-
Displays information for the specified SAP.
- ip-int-name
-
Displays information about the specified interface.
- ip-address
-
Displays information about the specified IP address.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of PPPoE statistics information.
Output Example*A:ALA-49# show service id 20 pppoe statistics
===============================================================================
PPPoE statistics for IES service 20
===============================================================================
Packet Type Received Transmitted
-------------------------------------------------------------------------------
PADI 2 -
PADO - 2
PADR 2 -
PADS - 2
PADT 0 0
session 9838 9839
-------------------------------------------------------------------------------
Drop Counters
-------------------------------------------------------------------------------
Rx Invalid Version : 0
Rx Invalid Type : 0
Rx Invalid Code : 0
Rx Invalid Session : 0
Rx Invalid Length : 0
Rx Invalid Tags : 0
Rx Invalid AC-Cookie : 0
Rx Dropped : 0
===============================================================================
*A:ALA-49#
statistics
Syntax
statistics
Context
[Tree] (clear>router>l2tp>peer statistics)
[Tree] (clear>router>l2tp>tunnel statistics)
[Tree] (clear>router>l2tp>group statistics)
[Tree] (clear>router>l2tp statistics)
Full Context
clear router l2tp peer statistics
clear router l2tp tunnel statistics
clear router l2tp group statistics
clear router l2tp statistics
Description
This command clears statistics for the specified context.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics [{sap sap-id | interface ip-int-name | ip-address}]
Context
[Tree] (clear>service>id>pppoe statistics)
Full Context
clear service id pppoe statistics
Description
This command clears PPPoE statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
Context
[Tree] (show>service>dynsvc>script statistics)
Full Context
show service dynamic-services script statistics
Description
This command displays dynamic service script statistics. Only non-zero values are shown.
The script statistics can be cleared with the "clear service statistics dynamic-services” command.
This command is not available in the MD-CLI.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of Dynamic Services script statistics information.
Output Example# show service dynamic-services script statistics
===============================================================================
Dynamic Services Script Statistics
===============================================================================
Description Counter
-------------------------------------------------------------------------------
python scripts with 0 retries due to timeout 46
setup - jobs launched 16
setup - jobs handled 16
setup - success 13
setup - syntax error 1
setup - execution failed 2
teardown - jobs launched 15
teardown - jobs handled 15
teardown - success 14
teardown - syntax error 1
-------------------------------------------------------------------------------
No. of Script Statistics: 10
-------------------------------------------------------------------------------
Last Cleared Time: 02/26/2013 09:59:07
===============================================================================
describes Dynamic Services script statistics fields.
Output field |
Description |
---|---|
Description |
The name of the script. |
Counter |
The number of times the script executed. |
python scripts with 0 retries due to timeout |
The number of retries due to timeouts. |
setup |
The setup script action. jobs launched — The number of times the setup jobs launched. jobs handled — The number of times the setup jobs were handled. success — The number of times the setup jobs were successful. syntax error — The number of setup syntax errors. execution failed — The number of times the setup failed. |
teardown |
The teardown script action. jobs launched — The number of times the teardown jobs launched. jobs handled — The number of times the teardown jobs were handled. success — The number of times the teardown jobs were successful. syntax error — The number of teardown syntax errors. |
statistics
Syntax
statistics iom (slot | all) [host | session | subscriber | summary] [non-zero-value-only]
statistics mda (mda | all) [host | session | subscriber | summary] [non-zero-value-only]
statistics port (port-id | all) [host | session | subscriber | summary] [non-zero-value-only]
statistics pw-port (pw-port | all) [host | session | subscriber | summary] [non-zero-value-only]
statistics system (pw-port | all) [host | session | subscriber | summary] [non-zero-value-only]
statistics service (svc-id | all) [host | session | summary] [non-zero-value-only]
statistics service {svc-id} subscriber-interface { sub-itf | all} [host | session | summary] [non-zero-value-only]
statistics service {svc-id} group-interface { grp-itf | all} [host | session | summary] [non-zero-value-only]
statistics sla-profiles
statistics sub-profiles
statistics system [host | session | subscriber | summary] [non-zero-value-only]
Context
[Tree] (show>subscr-mgmt statistics)
Full Context
show subscriber-mgmt statistics
Description
This command displays enhanced subscriber management statistics per port, PW port, MDA, IOM, system, service, subscriber interface, or group interface.
For each statistic, a current value and peak value is displayed. The peak value is the highest generated value since the last reset as a result of a system boot or the clear subscriber-mgmt peakvalue-stats command.
The user can execute the clear subscriber-mgmt peakvalue-stats command to reset the peak values.
Parameters
- iom slot
-
Displays specified IOM slot information.
- mda mda
-
Displays specified slot and mda information.
- port port-id
-
Specifies to display information for both the physical port ID and LAG.
- pw-port pw-port
-
Specifies to display information for a pseudowire port ID.
- all
-
Displays statistics of all IOM or MDA or port or pseudowire port in the system
- host
-
Displays v4/v6 host statistics only.
- session
-
Displays PPPoX/LAC/LNS session statistics only.
- sla-profiles
-
Displays the current and historical statistics for SLA profiles.
- service svc-id
-
Displays the current and historical statistics for service level profiles.
- sub-profiles
-
Displays the current and historical statistics for subscriber profiles.
- subscriber
-
Displays subscriber statistics only.
- subscriber-interface sub-itf
-
Displays specified subscriber interface level statistics, up to 32 characters.
- group-interface grp-itf
-
Displays specified group-interface level statistics, up to 32 characters.
- summary
-
Displays summary statistics only.
- non-zero-value-only
-
Displays only non-zero value counters.
The following tables describe the counters available in the show subscriber management statistics command output.
The following terminology is used to indicate applicability of the stats:
-
ESM — Enhanced Subscriber Management. Subscriber traffic forwarded via subscriber queues. Enabled with SAP sub-sla-mgmt in no shutdown state
-
BSM — Basic Subscriber Management. Subscriber traffic forwarded via SAP queues. SAP sub-sla-mgmt must be in shutdown state. For DHCP, dhcp lease-populate or dhcp6-relay lease-populate must be enabled to count the leases. For IPv4, if anti-spoof is enabled on the SAP, a subscriber host is instantiated.
-
Routed CO — IES or VPRN service with subscriber interface and group interface constructs
-
Bridged CO — VPLS service with DHCPv4 lease management enabled (lease-populate)
-
regular interface — IES or VPRN interface (none subscriber-interface or group-interface)
-
Host (also subscriber host) — A resource in the system that is used for traffic forwarding and security related actions. The creation of a subscriber host entry is linked to anti-spoof being enabled on a SAP. For ESM, anti-spoof is mandatory and hence every connected {IP/MAC} consumes by default a subscriber host entry. A DHCP6 IA-PD can also be modeled as a managed route. In this case, no subscriber host is instantiated. For BSM, anti-spoof is optional on regular interfaces. An IPv4 static-host and DHCPv4 lease do not result in a subscriber host instantiation when anti-spoof is disabled on the SAP.
Table 88. Host and Protocol Statistics Section
Counter
Counts
Applies to
IPv4
PPP Hosts - IPCP
IPv4 local terminated PPP hosts (PTA, LNS)
ESM, Routed CO
IPOE Hosts - DHCP
DHCPv4 hosts (lease states)
ESM, Routed CO, Bridged CO
IPOE Hosts - ARP
ARP hosts
ESM, Routed CO, Bridged CO
IPOE Hosts – Static
IPv4 static hosts
ESM, Routed CO, Bridged CO
IPOE Mngd Hosts – Data-trig
Data triggered IPv4 hosts
ESM, Routed CO
IPOE Mngd Hosts – AAA
vRGW managed static IPv4 addresses: IPv4 static hosts created via RADIUS (Alc-Reserved-Addresses)
ESM, Routed CO
IPOE Mngd Hosts – GTP
IPv4 GTP access host
ESM, Routed CO
IPOE Mngd Hosts – Bonding
IPv4 hosts associated with an internal IPoE session of a connection bonding subscriber context
ESM, Routed CO
IPOE Hosts BSM - DHCP
DHCPv4 hosts (lease states: anti-spoof and lease-populate enabled)
BSM, Routed CO, Bridged CO, regular interface
IPOE Hosts BSM – Static
IPv4 static hosts (with anti-spoof enabled)
BSM, Routed CO, Bridged CO, regular interface
IPOE BSM - DHCP
DHCPv4 lease states (with lease-populate enabled, no anti-spoof)
BSM, Routed CO, Bridged CO, regular interface
IPOE BSM – Static
IPv4 static hosts (no anti-spoof)
BSM, Routed CO, Bridged CO, regular interface
IPv6
PPP Hosts – SLAAC
Local terminated IPv6 wan-host – SLAAC (PTA, LNS)
ESM, Routed CO
PPP Hosts - DHCP6 (NA)
Local terminated IPv6 wan-host (PTA, LNS) – DHCP6 IA-NA leases over PPP
ESM, Routed CO
PPP Hosts - DHCP6 (PD)
Local terminated IPv6 pd-host (PTA, LNS) – DHCP6 IA-PD leases over PPP (excluding PD as managed route)
ESM, Routed CO
PPP Mngd Routes - DHCP6 (PD)
IPv6 (PTA, LNS) – DHCP6 IA-PD leases over PPP (PD as managed route only)
ESM, Routed CO
IPOE Hosts – SLAAC
IPv6 wan-host – SLAAC
ESM, Routed CO
IPOE Hosts - DHCP6 (NA)
IPv6 wan-host – DHCP6 IA-NA leases
ESM, Routed CO
IPOE Hosts - DHCP6 (PD)
IPv6 pd-host – DHCP6 IA-PD leases (excluding PD as managed route)
ESM, Routed CO
IPOE Mngd Routes - DHCP6 (PD)
IPv6 – DHCP6 IA-PD leases (PD as managed route only)
ESM, Routed CO
IPOE Hosts – Static (WAN)
IPv6 static hosts with prefix-length equal to /128
ESM, Routed CO
IPOE Hosts – Static (Pfx)
IPv6 static hosts with prefix-length shorter than /128
ESM, Routed CO
IPOE Mngd Hosts – Data-trig (Pfx)
Data triggered IPv6 Prefix host (prefix length shorter than /128)
ESM, Routed CO
IPOE Mngd Hosts – Data-trig (Pfx)
Data triggered IPv6 Prefix host (prefix length shorter than /128)
ESM, Routed CO
IPv6 (Cont)
IPOE Mngd Routes – Data-trig (Pfx)
Data triggered IPv6 Prefix (prefix length shorter than /128) modeled as a managed route
ESM, Routed CO
IPOE Mngd Hosts - AAA
(currently unused)
Not applicable
IPOE Mngd Hosts – GTP (SLAAC)
IPv6 (SLAAC) GTP Access host
ESM, Routed CO
IPOE Mngd Hosts - Bonding
IPv6 hosts associated with an internal IPoE session of a connection bonding subscriber context..
ESM, Routed CO
IPOE BSM - DHCP6 (NA)
IPv6 – DHCP6 IA-NA leases (lease-populate)
BSM, regular interface
IPOE BSM - DHCP6 (PD)
IPv6 – DHCP6 IA-PD leases (lease-populate)
BSM, regular interface
Total
PPP Hosts
Local terminated PPP hosts (PTA, LNS)
ESM
IPOE Hosts
Total IPv4 and IPv6 IPOE hosts
ESM
IPv4 Hosts
Total IPv4 hosts, PPP (PTA, LNS) and IPOE
ESM
IPv6 Hosts
Total IPv6 hosts, PPP (PTA, LNS) and IPOE
ESM
IPv6 PD Mngd Routes
Total DHCP6 IA-PD leases modeled as a managed route. PPP (PTA, LNS) and IPOE
ESM
L2TP LAC Hosts
L2TP LAC hosts – single host per single or dual stack PPP session
Counter also increases for outgoing LTS sessions.
ESM, Routed CO
L2TP LNS Hosts
L2TP LNS hosts – single host per single or dual stack PPP session
ESM, Routed CO
Internal Hosts
Subscriber hosts for internal use. For example, LNS redirect hosts (for LTS, an LNS redirect host is also instantiated).
The internal LNS redirect host only counts against the system limit and not against the per line card limit.
ESM
Total (Cont)
Non-Sub-Traffic L2-Hosts
A host on a single subscriber SAP in a VPLS service that enables non-IP traffic to be forwarded using the specified SLA profile instance queues.
Host on a single subscriber SAP attached to an IES or VPRN group-interface that enables traffic normally forwarded using the SAP queues to flow using the specified SLA profile instance queues.
configure>service>vpls service-id>sap sap-id>sub-sla-mgmt single-sub-parameters>non-sub-traffic sub-profile sub-profile-name sla-profile sla-profile-name [subscriber sub-ident-string] [app-profile app-profile-name]
ESM, Routed CO, Bridged CO
DHCP leases
Total number of DHCPv4 lease states
ESM, BSM
DHCPv6 leases
Total number of DHCPv6 lease states
ESM, BSM
Subscriber Hosts
Counter displayed in the output of show>subscriber-mgmt>statistics [ iom | mda | port | pw-port]
ESM
System Hosts Scale
Counter displayed in the output of show>subscriber-mgmt>statistics system
This counter matches the number of hosts accounted for in the system wide limit.
ESM
Table 89. PPP Session Statistics Section
Counter
Counts
Applies to
Local
PPP Sessions - PPPoE
Local terminated PPPoE sessions (PTA)
ESM, Routed CO
PPP Sessions - PPPoEoA
Local terminated PPPoEoA sessions (PTA)
ESM, Routed CO
PPP Sessions - PPPoA
Local terminated PPPoA sessions (PTA)
ESM, Routed CO
PPP Sessions - L2TP (LNS)
Local terminated PPP sessions (L2TP LNS)
ESM, Routed CO
LAC
PPP Sessions - PPPoE
Tunneled PPPoE session (L2TP LAC)
ESM, Routed CO
PPP Sessions - PPPoEoA
Tunneled PPPoEoA session (L2TP LAC)
ESM, Routed CO
PPP Sessions - PPPoA
Tunneled PPPoA session (L2TP LAC)
ESM, Routed CO
PPP Sessions - L2TP (LTS)
Tunneled PPP session (L2TP LTS)
ESM, Routed CO
Total
PPP Sessions - established
PPP sessions that are established (at least one active host attached) – PTA/LAC/LTS/LNS
ESM, Routed CO
PPP Sessions - in setup
PPP sessions in setup (session created, host setup in progress) – PTA/LAC/LTS/LNS
ESM, Routed CO
PPP Sessions - local
Local terminated PPPoX sessions (PTA, L2TP LNS)
ESM, Routed CO
PPP Sessions - LAC
Tunneled PPPoX session (L2TP LAC, L2TP LTS)
ESM, Routed CO
L2TP
L2TP Tunnels - originator
Number of L2TP Tunnels originated on this node. (LAC/LTS)
ESM, Routed CO
.L2TP Tunnels - receiver
Number of L2TP Tunnels terminated on this node. (LNS/LTS)
ESM, Routed CO
Total L2TP Tunnels
Number of L2TP Tunnels originated or terminated on this node.
ESM, Routed CO
Table 90. IPoE Session Statistics Section
Counter
Counts
Applies to
Total
IPOE Sessions - established
IPoE sessions that are established (at least one active host attached).
ESM, Routed CO
IPOE Sessions- in setup
IPoE sessions in setup (session created, host setup in progress).
ESM, Routed CO
Table 91. Subscriber Statistics Section
Counter
Counts
Applies to
Total
Subscribers
Total number of active subscribers.
ESM, Routed CO, Bridged CO
Table 92. SubMgmt Statistics Summary Section
Counter
Counts
Hosts
IPv4
IPv6
Total IPv4 hosts
Total IPv6 hosts
Sessions
PPP
IPOE
Total PPP sessions established
Total IPOE sessions established
Subscribers
Total number of active subscribers
-
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following outputs are examples of subscriber management statistics information.
Output ExampleA:PE-1# show subscriber-mgmt statistics port 1/1/4 summary
===============================================================================
SubMgmt Statistics
===============================================================================
| Hosts | Sessions | Subscribers
Port Id | IPv4 IPv6 | PPP IPOE |
-------------------------------------------------------------------------------
1/1/4 | 2 2 | 1 1 | 2 (Curr)
| 3 3 | 1 2 | 3 (Peak)
===============================================================================
Output Example
A:PE-1# show subscriber-mgmt statistics sla-profiles
===============================================================================
SLA Profile Statistics
===============================================================================
SLA-Profile Name Current Peak Peak Timestamp
-------------------------------------------------------------------------------
tv-prof 0 0
hsi-prof 1 1 12/29/2016 15:50:50
hsi-iptv--prof 0 0
no-prof-1 1 1 01/03/2017 20:00:37
hsi-voip-prof 0 2 12/29/2016 18:42:44
-------------------------------------------------------------------------------
Total 2
===============================================================================
Output Example
A:PE-1# show subscriber-mgmt statistics sub-profiles
===============================================================================
Subscriber Profile Statistics
===============================================================================
Subscriber-Profile Name Current Peak Peak Timestamp
-------------------------------------------------------------------------------
no-prof 2 3 12/29/2016 18:42:44
sub-10M 0 0
sub-10M-UPNP 0 0
sub-20M 0 0
sub-20M-UPNP 0 0
-------------------------------------------------------------------------------
Total 2
===============================================================================
Output Example
A:pe1# show subscriber-mgmt statistics system
===============================================================================
Subscriber Management Statistics for System
===============================================================================
Type Current Peak Peak Timestamp
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Host & Protocol Statistics
-------------------------------------------------------------------------------
IPv4 PPP Hosts - IPCP 0 0
PPP Hosts - PFCP 0 0
IPOE Hosts - DHCP 0 0
IPOE Hosts - ARP 0 0
IPOE Hosts - Static 0 0
IPOE Hosts - PFCP 0 0
IPOE Mngd Hosts - Data-trig 0 0
IPOE Mngd Hosts - AAA 0 0
IPOE Mngd Hosts - GTP 0 0
IPOE Mngd Hosts - Bonding 0 0
IPOE Hosts BSM - DHCP 0 0
IPOE Hosts BSM - Static 0 0
IPOE BSM - DHCP 0 0
IPOE BSM - Static 0 0
-------------------------------------------------------------------------------
IPv6 PPP Hosts - SLAAC 0 0
PPP Hosts - DHCP6 (NA) 0 0
PPP Hosts - DHCP6 (PD) 0 0
PPP Mngd Routes - DHCP6 (PD) 0 0
PPP Hosts - PFCP (SLAAC) 0 0
PPP Hosts - PFCP (NA) 0 0
PPP Hosts - PFCP (PD) 0 0
IPOE Hosts - SLAAC 0 0
IPOE Hosts - DHCP6 (NA) 0 0
IPOE Hosts - DHCP6 (PD) 0 0
IPOE Mngd Routes - DHCP6 (PD) 0 0
IPOE Hosts - Static (WAN) 0 0
IPOE Hosts - Static (Pfx) 0 0
IPOE Hosts - PFCP (SLAAC) 0 0
IPOE Hosts - PFCP (NA) 0 0
IPOE Hosts - PFCP (PD) 0 0
IPOE Mngd Hosts - Data-trig (WAN) 0 0
IPOE Mngd Hosts - Data-trig (Pfx) 0 0
IPOE Mngd Routes - Data-trig (Pfx) 0 0
IPOE Mngd Hosts - AAA 0 0
IPOE Mngd Hosts - GTP (SLAAC) 0 0
IPOE Mngd Hosts - Bonding 0 0
IPOE BSM - DHCP6 (NA) 0 0
IPOE BSM - DHCP6 (PD) 0 0
-------------------------------------------------------------------------------
Total PPP Hosts 0 0
IPOE Hosts 0 0
IPv4 Hosts 0 0
IPv6 Hosts 0 0
IPv6 PD Mngd Routes 0 0
L2TP LAC Hosts 0 0
L2TP LNS Hosts 0 0
Internal Hosts 0 0
Non-Sub-Traffic L2-Hosts 0 0
DHCP Leases 0 0
DHCPv6 Leases 0 0
PFCP Hosts 0 0
System Hosts Scale 0 0
-------------------------------------------------------------------------------
statistics
Syntax
statistics sub-profile {sub-profile-name | all}
statistics sla-profile {sla-profile-name | all}
Context
[Tree] (clear>subscriber-mgmt statistics)
Full Context
clear subscriber-mgmt statistics
Description
This command clears the current and historical statistics.
Parameters
- sub-profile-name
-
Clears the statistics for a specific subscriber profile, limited to 32 characters.
- sub-profile all
-
Clears all subscriber profile statistics.
- sla-profile-name
-
Clears the statistics for a specific SLA profile, limited to 32 characters.
- sla-profile all
-
Clears all SLA profile statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics interface subscriber-interface [ id srrp-id]
Context
[Tree] (clear>router>srrp statistics)
Full Context
clear router srrp statistics
Description
This command clears statistics for SRRP instances.
Parameters
- subscriber-interface
-
Specifies an existing subscriber interface name up to 32 characters.
- srrp-id
-
Specifies an existing SRRP ID.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>service statistics)
Full Context
clear service statistics
Description
This command clears the statistics for a service.
Platforms
All
statistics
Syntax
statistics [policy name] [sap sap-id]
Context
[Tree] (show>service>id>auth statistics)
Full Context
show service id authentication statistics
Description
This command displays session authentication statistics for this service.
Parameters
- policy name
-
Specifies an existing authentication policy name.
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
Platforms
All
Output
The following output is an example of service authentication statistics information
Output Example*A:ALA-48# show service id 700 authentication statistics
================================================================
Authentication Statistics for service 700
================================================================
Client Packets Authenticate Fail : 0
Client Packets Authenticate Ok : 0
================================================================
*A:ALA-48#
statistics
Syntax
statistics [sap sap-id | sdp sdp-id:vc-id]
Context
[Tree] (show>service>id>mld-snooping statistics)
Full Context
show service id mld-snooping statistics
Description
This command displays MLD snooping statistics.
Platforms
All
Output
The following output is an example of MLD snooping statistics information.
Output Example*A:rbae_C# show service id 1 mld-snooping statistics
===============================================================================
MLD Snooping Statistics for service 1
===============================================================================
Message Type Received Transmitted Forwarded
-------------------------------------------------------------------------------
General Queries 109 0 327
Group Queries 0 0 0
Group-Source Queries 0 0 0
V1 Reports 0 0 0
V2 Reports 438 87 0
V1 Done 0 0 0
Unknown Type 0 N/A 0
-------------------------------------------------------------------------------
Drop Statistics
-------------------------------------------------------------------------------
Bad Length : 0
Bad MLD Checksum : 0
Bad Encoding : 0
No Router Alert : 0
Zero Source IP : 0
Wrong Version : 0
Lcl-Scope Packets : 0
Rsvd-Scope Packets : 0
Send Query Cfg Drops : 0
Import Policy Drops : 0
Exceeded Max Num Groups : 0
MCAC Policy Drops : 0
MCS Failures : 0
MVR From VPLS Cfg Drops : 0
MVR To SAP Cfg Drops : 0
===============================================================================
*A:rbae_C#
statistics
Syntax
statistics [evpn-mpls | sap sap-id | sdp sdp-id:vc-id | vxlan vtep ip-address vni vni]
Context
[Tree] (show>service>id>igmp-snooping statistics)
Full Context
show service id igmp-snooping statistics
Description
This command displays IGMP snooping statistics for the VPLS service.
Parameters
- evpn-mpls
-
Displays IGMP snooping statistics for EVPN-MPLS destinations
- sap-id
-
Displays IGMP snooping statistics for a specific SAP
- sdp-id
-
Displays the IGMP snooping statistics for a specific spoke or mesh SDP
- vc-id
-
The virtual circuit ID on the SDP ID for which to display information
- vxlan vtep ip-address vni <1..16777215>
-
Displays the IGMP snooping entries associated with a specific VXLAN binding, given by the VXLAN Termination Endpoint (VTEP) and VXLAN Network Identifier (VNI). This parameter only applies to the 7450 ESS or 7750 SR.
- vni
-
The VXLAN Network Identifier (VNI) for which to display information. This parameter only applies to the 7450 ESS or 7750 SR.
Platforms
All
Output
Output Example*A:ALA-1>show>service>id>snooping# statistics
===============================================================================
IGMP Snooping Statistics for service 1
===============================================================================
Message Type Received Transmitted Forwarded
-------------------------------------------------------------------------------
General Queries 4 0 4
Group Queries 0 0 0
Group-Source Queries 0 0 0
V1 Reports 0 0 0
V2 Reports 0 0 0
V3 Reports 0 0 0
V2 Leaves 0 0 0
Unknown Type 0 N/A 0
-------------------------------------------------------------------------------
Drop Statistics
-------------------------------------------------------------------------------
Bad Length : 0
Bad IP Checksum : 0
Bad IGMP Checksum : 0
Bad Encoding : 0
No Router Alert : 0
Zero Source IP : 0
Send Query Cfg Drops : 0
Import Policy Drops : 0
Exceeded Max Num Groups : 0
MVR From VPLS Cfg Drops : 0
MVR To SAP Cfg Drops : 0
===============================================================================
*A:ALA-1>show>service>id>snooping#
statistics
Syntax
statistics [ip-int-name | ip-address]
statistics group-interface [fwd-service service-id] [ip-int-name]
statistics host [ip-address]
Context
[Tree] (show>router>igmp statistics)
Full Context
show router igmp statistics
Description
This command displays IGMP statistics information.
Parameters
- ip-int-name
-
Displays information associated with the specified IP interface name, up to 32 characters.
- ip-address
-
Displays information associated with the specified IP address.
Platforms
All
Output
The following output is an example of IGMP statistics information. IGMP Statistics Fields provides statistical IGMP field descriptions.
Output Example*A:ALA-BA# show router igmp interface "IGMP_to_CE"
==================================================
IGMP Interface IGMP_to_CE Statistics
==================================================
Message Type Received Transmitted
--------------------------------------------------
Queries 0 0
Report V1 0 0
Report V2 0 0
Report V3 0 0
Leaves 0 0
--------------------------------------------------
Interface General Statistics
--------------------------------------------------
Bad Length : 0
Bad Checksum : 0
Unknown Type : 0
Drops : 0
Rx Non Local : 0
Rx Wrong Version : 0
Policy Drops : 0
No Router Alert : 0
Rx Bad Encodings : 0
Local Scope Pkts : 0
Resvd Scope Pkts : 0
MCAC Policy Drops : 0
--------------------------------------------------
Interface Source Group Statistics
--------------------------------------------------
(S,G) : 0
(*,G) : 0
==================================================
*A:ALA-BA#
*B:Dut-C# show router igmp statistics host
==================================================
IGMP Host Statistics
==================================================
Message Type Received Transmitted
--------------------------------------------------
Queries 0 1739
Report V1 0 0
Report V2 0 0
Report V3 10 0
Leaves 0 0
-------------------------------------------------------------------------------
General Host Statistics
-------------------------------------------------------------------------------
Bad Length : 0
Bad Checksum : 0
Unknown Type : 0
Bad Receive If : 0
Rx Non Local : 0
Rx Wrong Version : 0
Policy Drops : 0
No Router Alert : 0
Rx Bad Encodings : 0
Local Scope Pkts : 0
Resvd Scope Pkts : 0
MCAC Policy Drops : 0
==================================================
*B:Dut-C#
Label |
Description |
---|---|
IGMP Interface Statistics |
Lists the IGMP statistics for a particular interface. |
Message Type |
Queries — The number of IGMP general queries transmitted or received on this interface. |
Report — The total number of IGMP V1, V2, or V3 reports transmitted or received on this interface. |
|
Leaves — The total number of IGMP leaves transmitted on this interface. |
|
Received |
The total number of IGMP packets received on this interface. |
Transmitted |
The total number of IGMP packets transmitted from this interface. |
General Interface Statistics |
The general IGMP statistics. |
Bad Length |
The total number of IGMP packets with bad length received on this interface. |
Bad Checksum |
The total number of IGMP packets with bad checksum received on this interface. |
Unknown Type |
The total number of IGMP packets with unknown type received on this interface. |
Drops |
The total number of IGMP packets dropped on this interface. |
Rx Non Local |
The total number of IGMP packets received from a non-local sender. |
Rx Wrong Version |
The total number of IGMP packets with wrong versions received on this interface. |
Policy Drops |
The total number of IGMP packets dropped by import policies on this interface. |
No Router Alert |
The total number of IGMPv3 packets received on this interface which did not have the router alert flag set. |
Rx Bad Encodings |
The total number of IGMP packets with bad encodings received on this interface. |
Rx Pkt Drops |
The total number of IGMP receive packet drops on this interface. |
Local Scope Pkts |
The total number of IGMP packets with local scope received on this interface. |
Resvd Scope Pkts |
The total number of IGMP packets with reserved scope received on this interface. |
MCAC Policy Drops |
The total number of IGMP packets dropped by MCAC policies on this interface. |
statistics
Syntax
statistics all
statistics sap sap-id
statistics sdp sdp-id:vc-id
statistics vxlan vtep ip-address vni vni-id
Context
[Tree] (clear>service>id>mld-snooping statistics)
Full Context
clear service id mld-snooping statistics
Description
This command clears MLD snooping statistics.
Parameters
- sap-id
-
Clears MLD snooping statistics for the specified SAP.
- sdp-id
-
Clears MLD snooping statistics associated with the specified SDP. For a spoke-SDP, the VC ID must be specified; for a mesh SDP, the VC ID is optional.
- vni-id
-
Clears the MLD snooping statistics for the specified VXLAN VNI id.
- ip-address
-
Specifies a specific configured static egress VTEP to clear the MLD snooping statistics associated only with the VTEP.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>service>id>authentication statistics)
Full Context
clear service id authentication statistics
Description
This command clears session authentication statistics for this service.
Platforms
All
statistics
Syntax
statistics {evpn-mpls | all | sap sap-id | sdp sdp-id:vc-id | vxlan vtep ip-address vni vni-id}]
Context
[Tree] (clear>service>id>igmp-snooping statistics)
Full Context
clear service id igmp-snooping statistics
Description
This command clears IGMP snooping statistics for the VPLS service.
Parameters
- all
-
Clears the IGMP snooping information for all port objects in the service
- evpn-mpls
-
Clears IGMP snooping statistics for EVPN-MPLS destinations
- sap-id
-
Clears the IGMP snooping information on the specified SAP
- sdp-id
-
Clears only IGMP snooping entries associated with the specified mesh SDP or spoke-SDP. For a spoke-SDP, the VC ID must be specified, for a mesh SDP, the VC ID is optional.
- vc-id
-
Clears statistics for the specified virtual circuit ID on the SDP ID
- vxlan vtep ip-address vni <1..16777215>
-
Clears the IGMP snooping statistics associated with a specific VXLAN destination given by the VXLAN Termination Endpoint (VTEP) and VXLAN Network Identifier (VNI). This parameter only applies to the 7450 ESS or 7750 SR.
- vni-id
-
Displays information for the specified VXLAN Network Identifier (VNI). This parameter only applies to the 7450 ESS or 7750 SR.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>subscr-mgmt>wlan-gw statistics)
Full Context
show subscriber-mgmt wlan-gw statistics
Description
This command displays statistics information.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
Context
[Tree] (show>service>id>spb statistics)
Full Context
show service id spb statistics
Description
This command displays SPB statistics.
Platforms
All
Output
The following output is an example of service SPB statistics information.
Output ExampleA:cses-B01# show service id spb statistics
===============================================================================
ISIS Statistics
===============================================================================
ISIS Instance : 1024 SPF Runs : 4
Purge Initiated : 0 LSP Regens. : 11
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 31 31 0 9 0
IIH 532 532 0 533 0
CSNP 479 479 0 479 0
PSNP 9 9 0 27 0
Unknown 0 0 0 0 0
===============================================================================
statistics
Syntax
statistics [sap sap-id] [ sdp sdp-id:vc-id] [family]
Context
[Tree] (show>service>id>pim-snooping statistics)
Full Context
show service id pim-snooping statistics
Description
This command displays PIM statistics information.
Parameters
- sap-id
-
Displays the statistics associated with the specified SAP
- sdp-id:vc-id
-
Displays the statistics associated with the specified SDP
- family
-
Displays either IPv4 or IPv6 statistics
Platforms
All
Output
The following output is an example of service PIM snooping statistics information.
Output Example*A:PE# show service id 1 pim-snooping statistics
=================================================================
PIM Snooping Statistics ipv4
=================================================================
Message Type Received Transmitted Rx Errors
-----------------------------------------------------------------
Hello 36 - 0
Join Prune 8 8 0
Total Packets 44 8
-------------------------------------------------------------------------------
General Statistics
-------------------------------------------------------------------------------
Rx Neighbor Unknown : 0
Rx Bad Checksum Discard : 0
Rx Bad Encoding : 0
Rx Bad Version Discard : 0
Join Policy Drops : 0
-------------------------------------------------------------------------------
Source Group Statistics
-------------------------------------------------------------------------------
(S,G) : 1
(*,G) : 0
=================================================================
*A:PE#
statistics
Syntax
statistics {all | ipv4 | ipv6 | mac}
statistics group grp-address
Context
[Tree] (clear>service>id>mfib statistics)
Full Context
clear service id mfib statistics
Description
This command clears multicast FIB statistics for the VPLS service.
Parameters
- all
-
Clears all statistics for the service ID
- ipv4
-
Clears IPv4 address statistics for the service ID
- ipv6
-
Clears IPv6 address statistics for the service ID
- mac
-
Clears MAC address statistics for the service ID
- grp-address
-
Specifies an IGMP multicast group address that receives data on an interface
Platforms
All
statistics
Syntax
statistics [evpn-mpls | sap sap-id | sdp sdp-id:vc-id | vxlan vtep ip-address vni vni-id] [family]
Context
[Tree] (clear>service>id>pim-snooping statistics)
Full Context
clear service id pim-snooping statistics
Description
This command clears PIM snooping statistics for the specified SAP or SDP.
Parameters
- sap-id
-
Clears PIM snooping statistics for the specified SAP
- sdp-id:vc-id
-
Clears PIM statistics for the specified SDP. For a spoke-SDP, the VC ID must be specified; for a mesh SDP, the VC ID is optional.
- family
-
Displays either IPv4 or IPv6 information
- evpn-mpls
-
Clears PIM snooping statistics for EVPN-MPLS destinations
Platforms
All
statistics
Syntax
statistics [summary] [sap sap-id]
Context
[Tree] (show>service>id>host-connectivity-verify statistics)
Full Context
show service id host-connectivity-verify statistics
Description
This command displays host connectivity verification statistics.
Parameters
- sap-id
-
Specifies the SAP ID to show statistics for.
- summary
-
Displays host connectivity verify summary information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of host connectivity verification statistics information, and Show Host Connectivity Verify Statistics Field Descriptions describes the output fields.
Output ExampleA:ALA-48>show>service>id# host-connectivity-verify statistics sap 1/1/9:0
==============================================================================
Host connectivity check statistics
==============================================================================
Svc SapId/ DestIp Last Time Oper
Id SdpId Address Response Expired State
------------------------------------------------------------------------------
1000 551/2/3:0 10.144.145.1 Up
==============================================================================
A:ALA-48>show>service>id#
Label |
Description |
---|---|
Svc Id |
The service identifier. |
SapId/SdpId |
The SAP and SDP identifiers. |
DestIp Address |
The destination IP address. |
Last Response |
The time when the last response was received. |
Time Expired |
Displays whether the interval value has expired. |
Oper State |
Displays the current operational state of the service. |
statistics
Syntax
statistics
Context
[Tree] (show>router>vrrp statistics)
Full Context
show router vrrp statistics
Description
This command displays statistics for VRRP instance.
Platforms
All
Output
The following output is an example of VRRP statistics information, and table describes the fields.
Output ExampleA:ALA-48# show router vrrp statistics
===============================================================================
VRRP Global Statistics
===============================================================================
VR Id Errors : 0 Version Errors : 0
Checksum Errors : 0
===============================================================================
Label |
Description |
---|---|
VR Id Errors |
Displays the number of virtual router ID errors |
Version Errors |
Displays the number of version errors |
Checksum Errors |
Displays the number of checksum errors |
statistics
Syntax
statistics
statistics interface interface-name [vrid virtual-router-id]
statistics interface interface-name vrid virtual-router-id ipv6
Context
[Tree] (clear>router>vrrp statistics)
Full Context
clear router vrrp statistics
Description
This command clears statistics for VRRP instances on an IP interface or VRRP priority control policies.
Parameters
- interface-name
-
Clears the VRRP statistics for all VRRP instances on the specified IP interface.
- virtual-router-id
-
Clears the VRRP statistics for the specified VRRP instance on the IP interface.
- ipv6
-
Clears IPv6 statistics for the specified interface.
Platforms
All
statistics
Syntax
statistics [ip-addr | ip-int-name]
Context
[Tree] (show>router>rip statistics)
Full Context
show router rip statistics
Description
Display Interface level statistics for the RIP protocol.
If no IP address or interface name is specified, then all configured RIP interfaces are displayed.
If an IP address or interface name is specified, then only data regarding the specified RIP interface is displayed.
Parameters
- ip-addr | ip-int-name
-
Displays statistics for the specified IP interface.
Platforms
All
Output
The following output is an example of RIP statistics information, and Show RIP Statistics Field Descriptions describes the output fields.
Output ExampleRIP Statistics
===============================================================================
Learned Routes : 0 Timed Out Routes : 0
Current Memory : 120624 Maximum Memory : 262144
-------------------------------------------------------------------------------
Interface "to-web"
-------------------------------------------------------------------------------
Primary IP : 10.1.1.3 Update Timer : 30
Timeout Timer : 180 Flush Timer : 120
Counter Total Last 5 Min Last 1 Min
------------------------------------------------------------------------------
Updates Sent 0 0 0
Triggered Updates 0 0 0
Bad Packets Received 0 0 0
RIPv1 Updates Received 0 0 0
RIPv1 Updates Ignored 0 0 0
RIPv1 Bad Routes 0 0 0
RIPv1 Requests Received 0 0 0
RIPv1 Requests Ignored 0 0 0
RIPv2 Updates Received 0 0 0
RIPv2 Updates Ignored 0 0 0
RIPv2 Bad Routes 0 0 0
RIPv2 Requests Received 0 0 0
RIPv2 Requests Ignored 0 0 0
Authentication Errors 0 0 0
==============================================================================
*A:ALA-12#
Label |
Description |
---|---|
Learned Routes |
The number of RIP-learned routes exported to RIP neighbors. |
Timed Out Routes |
The number of routes that have been timed out. |
Current Memory |
The amount of memory used by this RIP router instance. |
Maximum Memory |
The amount of memory allocated for this RIP router instance. |
Interface |
Displays the name of each interface configured in RIP and associated RIP statistics. |
Primary IP |
The interface IP address. |
Update Timer |
The current setting of the RIP update timer value expressed in seconds. |
Timeout Timer |
The current RIP timeout timer value expressed in seconds. |
Flush Timer |
The number of seconds after a route has been declared invalid that it is flushed from the route database. |
Updates Sent |
Total — The total number of RIP updates that were sent. Last 5 Min — The number of RIP updates that were sent in the last 5 minutes. Last 1 Min — The number of RIP updates that were sent in the last 1 minute. |
Triggered Updates |
Total — The total number of triggered updates sent. These updates are sent before the entire RIP routing table is sent. Last 5 Min — The number of triggered updates that were sent in the last 5 minutes. Last 1 Min — The number of triggered updates that were sent in the last 1 minute. |
Bad Packets Received |
Total — The total number of RIP updates received on this interface that were discarded as invalid. Last 5 Min — The number of RIP updates received on this interface that were discarded as invalid in the last 5 minutes. Last 1 Min —The number of RIP updates received on this interface that were discarded as invalid in the last 1 minute. |
RIPv1 Updates Received |
Total — The total number of RIPv1 updates received. Last 5 Min — The number of RIPv1 updates received in the last 5 minutes. Last 1 Min — The number of RIPv1 updates received in the last 1 minute. |
RIPv1 Updates Ignored |
Total — The total number of RIPv1 updates ignored. Last 5 Min — The number of RIPv1 updates ignored in the last 5 minutes. Last 1 Min — The number of RIPv1 updates ignored in the last 1 minute. |
RIPv1 Bad Routes |
Total — The total number of bad routes received from the peer. Last 5 Min — The number of bad routes received from the peer in the last 5 minutes. Last 1 Min — The number of bad routes received from the peer in the last minute. |
RIPv1 Requests Received |
Total — The total number of times the router received RIPv1 route requests from other routers. Last 5 Min — The number of times the router received RIPv1 route requests from other routers in the last 5 minutes. Last 1 Min — The number of times the router received RIPv1 route requests from other routers in the last 1 minute. |
RIPv1 Requests Ignored |
Total — The total number of times the router ignored RIPv1 route requests from other routers. Last 5 Min — The number of times the router ignored RIPv1 route requests from other routers in the last 5 minutes. Last 1 Min — The number of times the router ignored RIPv1 route requests from other routers in the last 1 minute. |
RIPv2 Updates Received |
Total — The total number of RIPv2 updates received. Last 5 Min — The number of RIPv2 updates received in the last 5 minutes. Last 1 Min — The number of RIPv2 updates received in the last minute. |
RIPv2 Updates Ignored |
Total — The total number of RIPv2 updates ignored. Last 5 Min — The number of RIPv2 updates ignored in the last 5 minutes. Last 1 Min — The number of RIPv2 updates ignored in the last minute. |
RIPv2 Bad Routes |
Total — The total number of bad routes received from the peer. Last 5 Min — The number of bad routes received from the peer in the last 5 minutes. Last 1 Min — The number of bad routes received from the peer in the last minute. |
RIPv2 Requests Received |
Total — The total number of times the router received RIPv2 route requests from other routers. Last 5 Min — The number of times the router received RIPv2 route requests from other routers in the last 5 minutes. Last 1 Min — The number of times the router received RIPv2 route requests from other routers in the last minute. |
RIPv2 Requests Ignored |
Total — The total number of times the router ignored RIPv2 route requests from other routers. Last 5 Min — The number of times the router ignored RIPv2 route requests from other routers in the last 5 minutes. Last 1 Min —The number of times the router ignored RIPv2 route requests from other routers in the last minute. |
Authentication Errors |
Total — The total number of authentication errors to secure table updates. Last 5 Min — The number of authentication errors to secure table updates in the last 5 minutes. Last 1 Min —The number of authentication errors to secure table updates in the last minute. |
statistics
Syntax
statistics [neighbor {ip-address | ip-int-name}]
Context
[Tree] (clear>router>rip statistics)
Full Context
clear router rip statistics
Description
This command clears statistics for RIP neighbors.
Parameters
- {ip-address | ip-int-name}
-
Clears the statistics for the specified RIP interface.
Platforms
All
statistics
Syntax
statistics [neighbor {ip-int-name | ip-address}]
Context
[Tree] (clear>router>ripng statistics)
Full Context
clear router ripng statistics
Description
This command clears statistics for RIPng neighbors.
Parameters
- {ip-int-name | ip-address}
-
Clears the statistics for the specified RIPng interface.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>router>ldp statistics)
Full Context
show router ldp statistics
Description
This command displays LDP instance statistics related information.
Platforms
All
Output
Output Example*A:Dut-A# show router ldp statistics
===============================================================================
LDP Statistics for IPv4 LSR ID 10.20.1.1:0
IPv6 LSR ID 3ffe::a14:101[0]
===============================================================================
Session/Discovery
-------------------------------------------------------------------------------
Active IPv4 Sess : 3 Active IPv6 Sess : 3
Active IPv4 LinkAdj: 2 Active IPv6 LinkAdj : 2
Active IPv4 TargAdj: 1 Active IPv6 TargAdj : 1
Active IPv4 If : 2 Inactive IPv4 If : 0
Active IPv6 If : 2 Inactive IPv6 If : 0
Active IPv4 Peers : 1 Inactive IPv4 Peers : 0
Active IPv6 Peers : 1 Inactive IPv6 Peers : 0
IPv4 Attempted Sess: 0 IPv6 Attempted Sess : 0
IPv4 OLoad If : 0 IPv4 OLoad Targ Peers: 0
IPv6 OLoad If : 0 IPv6 OLoad Targ Peers: 0
-------------------------------------------------------------------------------
Protocol Stats
-------------------------------------------------------------------------------
No Hello Err : 0 Param Adv Err : 0
Max PDU Err : 0 Label Range Err : 0
Bad LDP Id Err : 0 Bad PDU Len Err : 0
Bad Mesg Len Err : 0 Bad TLV Len Err : 0
Unknown TLV Err : 0 Bad Proto Ver Err : 0
Malformed TLV Err : 0 Keepalive Expired Err: 0
Shutdown Notif Sent: 0 Shutdown Notif Recv : 0
-------------------------------------------------------------------------------
Prefixes
-------------------------------------------------------------------------------
IPv4 Pfx FECs Sent : 10 IPv4 Pfx FECs Recv : 10
IPv6 Pfx FECs Sent : 10 IPv6 Pfx FECs Recv : 10
IPv4PfxFecOLSessSnt: 0 IPv4PfxFecOLSessRecv : 0
IPv6PfxFecOLSessSnt: 0 IPv6PfxFecOLSessRecv : 0
IPv4PfxFecInOLoad : 0 IPv6PfxFecInOLoad : 0
-------------------------------------------------------------------------------
P2MP
-------------------------------------------------------------------------------
IPv4 P2MP FECs Sent: 0 IPv4 P2MP FECs Recv : 0
IPv6 P2MP FECs Sent: 0 IPv6 P2MP FECs Recv : 0
IPv4P2MPFecOLSessSn: 0 IPv4P2MPFecOLSessRecv: 0
IPv6P2MPFecOLSessSn: 0 IPv6P2MPFecOLSessRecv: 0
IPv4P2MPFecInOLoad : 0 IPv6P2MPFecInOLoad : 0
-------------------------------------------------------------------------------
Services
-------------------------------------------------------------------------------
Svc FEC128s Sent : 0 Svc FEC128s Recv : 0
Svc FEC129s Sent : 0 Svc FEC129s Recv : 0
Svc Fec128 OLSessSn: 0 Svc Fec128 OLSessRecv: 0
Svc Fec129 OLSessSn: 0 Svc Fec129 OLSessRecv: 0
Svc Fec128 InOLoad : 0 Svc Fec129 InOLoad : 0
===============================================================================
statistics
Syntax
statistics
Context
[Tree] (clear>router>ldp statistics)
Full Context
clear router ldp statistics
Description
This command clears LDP instance statistics.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>router>rsvp statistics)
Full Context
show router rsvp statistics
Description
This command displays global statistics in the RSVP instance.
Platforms
All
Output
The following output is an example of RSVP statistics information.
RSVP Statistics Output Fields describes RSVP statistics output fields.
Label |
Description |
---|---|
PATH Timeouts |
The total number of path timeouts. |
RESV Timeouts |
The total number of RESV timeouts. |
*A:SR1# /show router rsvp statistics
===============================================================================
RSVP Global Statistics
===============================================================================
PATH Timeouts : 0 RESV Timeouts : 0
GR Helper PATH Tim*: 0 GR Helper RESV Tim*: 0
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:SRU4>show>router>rsvp# statistics
===============================================================================
RSVP Global Statistics
===============================================================================
PATH Timeouts : 1026 RESV Timeouts : 182
===============================================================================
*A:SRU4>show>router>rsvp#
statistics
Syntax
statistics lsp-ldp head ip-prefix/prefix-length src-ip ip-address
statistics lsp-ldp tail ip-prefix/prefix-length dst-ip ip-address
statistics src-ip ip-address dst-ip ip-address
statistics all
statistics src-ip ip-address dst-ip ip-address lsp-rsvp {head | tail} tunnel-id [0..4294967295] lsp-id [0..4294967295]
statistics mpls-tp lsp-name path {working | protect}
statistics p2mp-interface interface-name
statistics src-ip ip-address lsp-rsvp {head | tail} rsvp-session-name [256 chars max]
Context
[Tree] (clear>router>bfd statistics)
Full Context
clear router bfd statistics
Description
This command clears BFD statistics.
Parameters
- all
-
Clears all statistics for the BFD instance.
- dst-ip ip-address
-
Clears statistics about the specified destination IPv4 or IPv6 address.
- ip-prefix/prefix-length
-
Clears statistics for the specified IP prefix.
- lsp-id [0..4294967295]
-
Clears statistics about the specified LSP ID.
- lsp-ldp head
-
Clears statistics for the head of the LSP LDP link.
- lsp-ldp tail
-
Clears statistics for the tail of the LSP LDP link.
- lsp-rsvp {head | tail}
-
Clears statistics about the specified link type.
- mpls-tp lsp-name
-
Clears statistics about the specified MPLS TP LSP.
- p2mp-interface interface-name
-
Clears statistics about the specified P2MP interface.
- path {working | protect}
-
Clears statistics about the working or protect path.
- rsvp-session-name [256 chars max]
-
Clears statistics about the specified RSVP session.
- src-ip ip-address
-
Clears statistics about the specified source IPv4 or IPv6 address.
- tunnel-id [0..4294967295]
-
Clears statistics about the specified tunnel ID.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>router>rsvp statistics)
Full Context
clear router rsvp statistics
Description
This command clears global statistics for the RSVP instance, for example, clears path and resv timeout counters.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>isa statistics)
Full Context
show isa statistics
Description
Commands in this context display ISA statistical information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
Context
[Tree] (clear>video statistics)
Full Context
clear video statistics
Description
This command clears video related statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-1s, 7750 SR-2s, 7750 SR-7s, 7750 SR-14s
statistics
Syntax
statistics
Context
[Tree] (show>router>bier statistics)
Full Context
show router bier statistics
Description
This command displays BIER statistics.
Platforms
All
statistics
Syntax
statistics group-interface [fwd-service service-id] ip-in-name
statistics group-interface all
statistics host ip-address
statistics host all
statistics [interface ip-int-name | ip-address]
Context
[Tree] (clear>router>igmp statistics)
Full Context
clear router igmp statistics
Description
This command clears IGMP statistics on a specified interface or IP address.
An interface, group, and source cannot be specified at the same time.
Parameters
- group-interface interface-name
-
Clears the IGMP statistics on the specified group interface.
- group-interface all
-
Clears the IGMP statistics on all group interfaces.
- service-id
-
Specifies the service ID.
- host ip-address
-
Clears the IGMP statistics on the specified host.
- host all
-
Clears the IGMP statistics on all hosts.
- interface ip-int-name
-
Clears the IGMP statistics on the specified interface.
- interface ip-address
-
Clears the IGMP statistics on the specified IP address.
Platforms
All
statistics
Syntax
statistics policy policy-name [bundle bundle-name] [ protocol {igmp | pim | igmpSnpg | mld}]
statistics
Context
[Tree] (show>router>mcac statistics)
Full Context
show router mcac statistics
Description
This command displays MCAC statistics.
Parameters
- policy-name
-
Specifies an existing multicast CAC (MCAC) policy name.
- bundle-name
-
Displays statistics for the specified existing multicast bundle name.
- protocol {igmp | pim | igmpSnpg | mld}
-
Displays statistics for the specified applicable protocol.
Platforms
All
statistics
Syntax
statistics [ip-int-name | ipv6-address]
statistics ipsec-interface ip-int-name
Context
[Tree] (show>router>mld statistics)
Full Context
show router mld statistics
Description
This command displays MLD statistics information.
Parameters
- ip-int-name
-
Displays information associated with the specified IP interface name, up to 32 characters.
- ipv6-address
-
Displays information associated with the specified IPv6 address.
- ipsec-interface ip-int-name
-
Displays information associated with the specified dynamic name for the MLD-enabled child_SA.
Platforms
All
Output
The following output is an example of MLD statistics information. MLD Statistics Fields provides statistical MLD field descriptions.
Output Example*A:ALA-BA# show router mld statistics
==================================================
MLD Interface Statistics
==================================================
Message Type Received Transmitted
--------------------------------------------------
Queries 0 9
Report V1 0 0
Report V2 0 0
Dones 0 0
-------------------------------------------------------------------------------
General Interface Statistics
-------------------------------------------------------------------------------
Bad Length : 0
Bad Checksum : 0
Unknown Type : 0
Bad Receive If : 0
Rx Non Local : 0
Rx Wrong Version : 0
Policy Drops : 0
No Router Alert : 0
Rx Bad Encodings : 0
Rx Pkt Drops : 0
Local Scope Pkts : 0
Resvd Scope Pkts : 0
MCAC Policy Drops : 0
-------------------------------------------------------------------------------
Source Group Statistics
-------------------------------------------------------------------------------
(S,G) : 0
(*,G) : 5
==================================================
*A:Dut-A#
Label |
Description |
---|---|
MLD Interface Statistics |
The MLD statistics for a particular interface. |
Message Type |
Queries — The number of MLD general queries transmitted or received on this interface. Report — The total number of MLD V1 or V2 reports transmitted or received on this interface. Dones — The total number of MLD dones transmitted on this interface. |
Received |
The total number of MLD packets received on this interface. |
Transmitted |
The total number of MLD packets transmitted from this interface. |
General Interface Statistics |
The general MLD statistics. |
Bad Length |
The total number of MLD packets with bad length received on this interface. |
Bad Checksum |
The total number of MLD packets with bad checksum received on this interface. |
Unknown Type |
The total number of MLD packets with unknown type received on this interface. |
Bad Receive If |
The total number of MLD packets incorrectly received on this interface. |
Rx Non Local |
The total number of MLD packets received from a non-local sender. |
Rx Wrong Version |
The total number of MLD packets with wrong versions received on this interface. |
Policy Drops |
The total number of MLD packets dropped by import policies on this interface. |
No Router Alert |
The total number of MLD packets received on this interface which did not have the router alert flag set. |
Rx Bad Encodings |
The total number of MLD packets with bad encodings received on this interface. |
Rx Pkt Drops |
The total number of MLD receive packet drops on this interface. |
Local Scope Pkts |
The total number of MLD packets with local scope received on this interface. |
Resvd Scope Pkts |
The total number of MLD packets with reserved scope received on this interface. |
MCAC Policy Drops |
The total number of MLD packets dropped by MCAC policies on this interface. |
statistics
Syntax
statistics group-interface [fwd-service service-id] ip-int-name
statistics group-interface all
statistics host ipv6-address
statistics host all
statistics [ip-int-name | ipv6-address]
statistics ipsec-interface ip-int-name
Context
[Tree] (clear>router>mld statistics)
Full Context
clear router mld statistics
Description
This command clears MLD statistics parameters.
Parameters
- service-id
-
Clears the MLD statistics for the service ID.
- group-interface interface-name
-
Clears the MLD statistics on the specified group interface.
- group-interface all
-
Clears the MLD statistics on all group interfaces.
- host all
-
Clears the MLD statistics on all hosts.
- host ipv6-address
-
Clears the MLD statistics on the specified host.
- ip-int-name
-
Clears statistics for the specified MLD interface name.
- ipv6-address
-
Clears statistics for the specified MLD IPv6 address.
- ipsec-interface ip-int-name
-
Clears statistics information for the specified dynamic name for the MLD-enabled child_SA.
Platforms
All
statistics
Syntax
statistics [peer ip-address]
Context
[Tree] (show>router>msdp statistics)
Full Context
show router msdp statistics
Description
This command displays statistics information related to a MSDP peer.
Parameters
- ip-address
-
Displays information about the specified peer IP address.
Platforms
All
Output
The following output is an example of MSDP statistics information. MSDP Statistics Fields provides MSDP statistics field descriptions.
Output ExampleA:ALA-48# show router msdp statistics
===============================================================================
MSDP Statistics
===============================================================================
Glo ActSrc Lim Excd: 0
-------------------------------------------------------------------------------
Peer Address : 10.20.1.1
-------------------------------------------------------------------------------
Last State Change : 0d 11:33:16 Last message Peer : 0d 00:00:17
RPF Failures : 0 Remote Closes : 0
SA Msgs Sent : 0 SA Msgs Recvd : 709
SA req. Msgs Sent : 0 SA req. Msgs Recvd : 0
SA res. Msgs Sent : 0 SA res. Msgs Recvd : 0
KeepAlive Msgs Sent: 694 KeepAlive Msgs Recd: 694
Unknown Msgs Sent : 0 Error Msgs Recvd : 0
-------------------------------------------------------------------------------
Peers : 1
===============================================================================
A:ALA-48#
Label |
Description |
---|---|
Last State Change |
The date and time the peer state changed. |
RPF Failures |
The number of reverse path forwarding (RPF) failures. |
SA Msgs Sent |
The number of source-active messages sent. |
SA req. Msgs Sent |
The number of source-active request messages sent. |
SA res. Msgs Sent |
The number of source-active response messages sent. |
KeepAlive Msgs Sent |
The number of keepalive messages sent. |
Unknown Msgs Sent |
The number of unknown messages received. |
Last message Peer |
The time the last message was received from the peer. |
Remote Closes |
The number of times the remote peer close. |
SA Msgs Recvd |
The number of source-active messages received. |
SA req. Msgs Recvd |
The number of source-active request messages received. |
SA res. Msgs Recvd |
The number of source-active response messages received. |
KeepAlive Msgs Recd |
The number of keepalive messages received. |
Error Msgs Recvd |
The number of unknown messages received. |
statistics
Syntax
statistics [peer ip-address]
Context
[Tree] (clear>router>msdp statistics)
Full Context
clear router msdp statistics
Description
This command clears IP address statistics of the peer to which Multicast Source Discovery Protocol (MSDP) source-active (SA) requests for groups matching this entry's group range were sent.
Parameters
- ip-address
-
Clears the statistics of the specified IP address.
Platforms
All
statistics
Syntax
statistics [ip-int-name | mt-int-name | ip-address | mpls-if-name] [family]
Context
[Tree] (show>router>pim statistics)
Full Context
show router pim statistics
Description
This command displays statistics for a particular PIM instance.
Parameters
- ip-int-name
-
Displays interface information associated with the specified IP interface name.
- mt-int-name
-
Displays information about the default core group address of the Multicast Distribution Tree (MDT) for the VPRN instance. The Multicast Tunnel (MT) interface for a VPRN is created when this object is set to a valid group address.
Syntax: vprn-id-mt-grp-ip-address
- ip-address
-
Displays interface information associated with the specified IP address.
- mpls-if-name
-
Displays information about the specified MPLS interface name.
Syntax: mpls-if-index
- family
-
Displays statistics information for the specified family.
Platforms
All
Output
The following output is an example of PIM statistics information. PIM Statistics Output Fields provides PIM statistics output field descriptions
Output ExampleA:ALA-1# show router pim statistics
=================================================================
PIM Statistics ipv4
=================================================================
Message Type Received Transmitted Rx Errors
-----------------------------------------------------------------
Hello 18009 12834 0
Join Prune 9135 1129 10
Core RPFV JP 0 0 0
MVPN RPFV JP 0 0 0
Asserts 0 0 0
Register 0 0 0
Null Register 0 0 0
Register Stop 0 0 0
BSM 0 0 0
Candidate RP Adv 0 0 0
Auto-RP Announce 2049 0 0
Auto-RP Mapping 2066 0 0
PIM DM Grafts 0 0 0
PIM DM Graft Acks 0 0 0
Total Packets 31231 13963
-----------------------------------------------------------------
Intra-AS AD 0 0 0
Inter-AS AD 0 0 0
Mdt-Safi 1323 10 0
S-PMSI AD 0 0 0
Leaf AD 0 0 0
Source-Active AD 0 0 0
Shared Tree Join 0 0 0
Source Tree Join 0 0 0
Total BGP Packets 1323 10
-------------------------------------------------------------------------------
General Statistics
-------------------------------------------------------------------------------
Rx Invalid Register : 0
Rx Neighbor Unknown : 10
Rx Bad Checksum Discard : 0
Rx Bad Encoding : 0
Rx Bad Version Discard : 0
Rx CRP No Router Alert : 0
Rx BSM Router Alert Drops : 0
Rx BSM Wrong If Drops : 0
Rx Invalid Join Prune : 0
Rx Invalid Auto-RP PDU : 0
RPF Mismatch Auto-RP Mapping PDU : 65
RPF Mismatch Auto-RP Announce PDU : 80
Rx Unknown PDU Type : 0
Join Policy Drops : 0
Register Policy Drops : 0
Bootstrap Import Policy Drops : 0
Bootstrap Export Policy Drops : 0
Mcac Policy Drops : 0
Fwd Candidate RP Adv : 0
Fwd Candidate RP Adv Drops : 0
S-pmsi Join TLV PDUs txd. : 0
S-pmsi Join TLV PDUs rcd. : 0
S-pmsi Join TLV PDUs txd. Drops : 0
S-pmsi Join TLV PDUs rcd. Drops : 0
S-pmsi Maximum-P2mp-Spmsi Hits : 0
P2mp Pmsi Create Failures : 0
P2mp Pmsi Request Failures : 0
PDU Drops on Non-PIM/Down Intf : 0
Active Tx S-pmsis : 0
Active Tx MS-pmsis : 0
Active Rx S-pmsis : 0
Active Rx Pseudo S-pmsis : 0
Total Tx S-pmsis : 0
Total Rx S-pmsis : 0
-------------------------------------------------------------------------------
Source Group Statistics
-------------------------------------------------------------------------------
(S,G) : 2
(*,G) : 2
(*,*,RP) : 0
================================================================
Label |
Description |
---|---|
PIM Statistics |
The section listing the PIM statistics for a particular interface |
Message Type |
The type of message. Hello — The number of PIM hello messages received or transmitted Join Prune — The number of PIM join prune messages received or transmitted Asserts — The number of PIM assert messages received or transmitted Register — The number of register messages received or transmitted Null Register — The number of PIM null register messages received or transmitted Register Stop — The number of PIM register stop messages received or transmitted BSM — The number of PIM Bootstrap messages (BSM) received or transmitted Candidate RP Adv — The number of candidate RP advertisements Auto-RP Announce — The number of auto-RP announce (224.0.1.39) messages received or transmitted Auto-RP Mapping — The number of auto-RP mapping (224.0.1.40) messages received or transmitted |
Message Type |
PIM DM Grafts — The number of PIM graft messages received or transmitted PIM DM Graft Acks — The number of PIM graft acknowledgment messages received or transmitted Total Packets — The total number of packets transmitted and received. |
Received |
The number of messages received |
Transmitted |
The number of multicast data packets transmitted |
Rx Errors |
The total number of receive errors |
General Interface Statistics |
The section listing the general PIM interface statistics |
Register TTL Drop |
The number of multicast data packets which could not be encapsulated in Register messages because the time to live (TTL) was zero |
Tx Register MTU Drop |
The number of Bootstrap messages received on this interface but were dropped |
Rx Invalid Register |
The number of invalid PIM register messages received |
Rx Neighbor Unknown |
The number of PIM messages (other than hello messages) which were received and were rejected because the adjacency with the neighbor router was not already established |
Rx Bad Checksum Discard |
The number of PIM messages received, and which were discarded because of bad checksum |
Rx Bad Encoding |
The number of PIM messages with bad encodings received |
Rx Bad Version Discard |
The number of PIM messages with bad versions received |
Rx CRP No Router Alert |
The number of candidate-rp advertisements (C-RP-Adv) received, and which had no router alert option set |
Rx Invalid Join Prune |
The number of invalid PIM join prune messages received |
Rx Unknown PDU Type |
The number of packets received with an unsupported PIM type |
Join Policy Drops |
The number of times the join policy match resulted in dropping PIM join-prune message or one of the source group contained in the message |
Register Policy Drops |
The number of times the register policy match resulted in dropping PIM register message |
Bootstrap Import Policy Drops |
The number of Bootstrap messages received that were dropped because of Bootstrap import policy |
Bootstrap Export Policy Drops |
The number of Bootstrap messages that were not transmitted because of Bootstrap export policy. |
Source Group Statistics |
The section listing the source group statistics |
(S,G) |
The number of entries in which the type is (S,G) |
(*,G) |
The number of entries in which the type is (*,G) |
(*,*,RP) |
The number of entries in which the type is (*, *, rp) |
statistics
Syntax
statistics [family]
statistics [interface ip-int-name | mt-int-name | int-ip-address] [family]
statistics [group grp-ip-address] [source ip-address] [family]
Context
[Tree] (clear>router>pim statistics)
Full Context
clear router pim statistics
Description
This command clears PIM statistics on a specified interface or IP address.
An interface and group or source cannot be specified at the same time.
Parameters
- ip-int-name
-
Clears PIM statistics on the specified interface.
- ip-address
-
Clears PIM statistics on the specified IP address.
- mt-int-name
-
Clears the default core group address of the Multicast Distribution Tree (MDT) for the VPRN instance. The Multicast Tunnel (MT) interface for a VPRN is created when this object is set to a valid group address.
syntax: vprn-id-mt-grp-ip-address
- grp-ip-address
-
When only the group address is specified and no source is specified, (*,G) statistics are cleared. When the group address is specified along with the source address, then the (S,G) statistics are reset to zero.
- ip-address
-
When the source address is specified along with the group address, then the (S,G) statistics are reset to zero.
- family
-
Clears statistics family information.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>router>p2mp-sr-tree statistics)
Full Context
show router p2mp-sr-tree statistics
Description
This command displays P2MP SR tree statistics.
Platforms
All
Output
The following output is an example of P2MP SR tree statistics information.
The "Programming failures” count in tree SID statistics are not High Availability (HA) compatible and are reset upon an activity switch of the CPMs.
A:swsim103>show>router>p2mp-sr-tree# statistics
============================================================
P2MP-SR Statistics
============================================================
General
Total Number of p2mp-policies : 2
static : 2
pce : 0
sr-policy : 0
Total Number p2mp-candidate-path : 2
static : 2
pce : 0
sr-policy : 0
Total Number replication-segments : 4
static : 4
pce : 0
sr-policy : 0
Total Number next-hops : 2
static : 2
pce : 0
sr-policy : 0
Total Number push : 2
Total Number swap : 1
Total Number pop : 1
Total Number tunnel-allocated : 2
Total Number next-hop interfaces
inService : 1
outOfService : 0
unsupported : 0
mismatched : 0
without BFD : 0
BackPressure
DataPlane backpressure active : disabled
DataPlane backpressure count : 0
Errors
Unknown Originator Owner : 0
Duplicate TreeIds : 0
Programming failures
NhIdx : 0
Labels : 0
Tunnels : 0
Protection Grp : 0
statistics
Syntax
statistics
Context
[Tree] (show>eth-cfm statistics)
Full Context
show eth-cfm statistics
Description
This command displays the ETH-CFM statistics counters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of ETH-CFM statistics information. ETH-CFM Statistics Field Descriptions describes the ETH-CFM statistics fields.
Output Exampleshow eth-cfm statistics
===============================================================================
ETH-CFM System Statistics
===============================================================================
Rx Count : 10513196 Tx Count : 2294783
Dropped Congestion : 0 Discarded Error : 764766
AIS Currently Act : 0 AIS Currently Fail : 0
===============================================================================
=================================
ETH-CFM System Op-code Statistics
=================================
Op-code Rx Count Tx Count
---------------------------------
ccm 4588504 2294779
lbr 0 0
lbm 2 0
ltr 0 1
ltm 1 0
ais 0 0
lck 0 0
tst 0 0
laps 0 0
raps 0 0
mcc 0 0
lmr 0 0
lmm 0 0
1dm 0 0
dmr 0 0
dmm 4012644 0
exr 0 0
exm 0 0
csf 0 0
vsr 0 0
vsm 0 0
1sl 0 0
slr 0 0
slm 1912045 0
other 0 0
---------------------------------
Total 10513196 2294780
=================================
Label |
Description |
---|---|
Rx Count |
The ETH-CFM CPU receive rate, in PPS |
Tx Count |
The ETH-CFM CPU transmit rate, in PPS |
Dropped Congestion |
The number of valid or supported ETH-CFM packets not processed by the CPU as a result of resource contention |
Discard Error |
The number of ETH-CFM packets that did not pass validation |
statistics
Syntax
statistics session session-name dm meas-interval { 5-mins | 15-mins | 1-hour | 1-day | raw} interval-number interval-number [ all | bins | summary]
statistics session session-name dmm meas-interval { 5-mins | 15-mins | 1-hour | 1-day | raw} interval-number interval-number [ all | bins | summary]
statistics session session-name lmm meas-interval { 5-mins| 15-mins| 1-hour| 1-day| raw} interval-number interval-number
statistics session session-name slm meas-interval { 5-mins| 15-mins| 1-hour| 1-day| raw} interval-number interval-number
statistics session session-name twamp-light meas-interval { 5-mins | 15-mins | 1-hour | 1-day | raw} interval-number interval-number delay [ all | bins | summary]
Context
[Tree] (show>oam-pm statistics)
Full Context
show oam-pm statistics
Description
This command shows the delay statistics for the specified test using the parameters specified.
Parameters
- session-name
-
Identifies the session to be queried.
- dm
-
Specifies that the delay test is from the MPLS test family and is using dm style measurements for the delay.
- dmm
-
Specifies that the delay test is from the Ethernet test family and is using dmm style measurements for the delay.
- lmm
-
Specifies the loss test is from the Ethernet test family and is using lmm style measurements for the loss.
- slm
-
Specifies that the loss test is from the Ethernet test family and is using slm style measurements for the loss.
- twamp-light
-
Specifies that the delay test is from the IP test family and is using twamp-light style measurements for the delay.
- meas-interval
-
Identifies the measurement interval to query for the statistics. When raw is specified, the interval number is not to be included because there is only one raw cumulative bin.
- interval-number
-
Specifies the numerical reference that indicates the position from the latest sample window. The number 1 is the most recent with all higher numbers being that position in the past from current.
- [all | bins | summary]
-
Specifies a keyword to filter the output.
- delay
-
Indicates that the statistics being queried are for delay. TWAMP-Light PDUs carry both delay and loss informational elements and it is not clear from only the test type name which statistic the operator requires.
- loss
-
Indicates the statistics being queried are for loss. TWAMP-Light PDUs carry both delay and loss informational elements and it is not clear from only the test type name which statistic the operator requires. This keyword is specific to twamp-light.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>eth-cfm statistics)
Full Context
clear eth-cfm statistics
Description
This command clears the eth-cfm statistics counters maintained in clearEthCfmStatistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
statistics
Syntax
statistics
statistics interface {ip-int-name | ip-address}
statistics policy name
Context
[Tree] (show>router>authentication statistics)
Full Context
show router authentication statistics
Description
This command displays interface or policy authentication statistics.
Parameters
- ip-int-name | ip-address
-
Specifies an existing interface name or IP address.
- name
-
Specifies an existing policy name.
Platforms
All
Output
Authentication Statistics Output — The following output is an example of authentication statistics, and Authentication Statistics Fields describes the fields.
Output ExampleA:ALU-3>show>router>auth# statistics
===================================================================
Authentication Global Statistics
===================================================================
Client Packets Authenticate Fail : 0
Client Packets Authenticate Ok : 12
===================================================================
Label |
Description |
---|---|
Client Packets Authenticate Fail |
The number of packets that failed authentication |
Client Packets Authenticate Ok |
The number of packets that were authenticated |
statistics
Syntax
statistics [interface ip-int-name | ip-address]
Context
[Tree] (clear>router>authentication statistics)
Full Context
clear router authentication statistics
Description
This command clears authentication statistics.
Parameters
- ip-int-name
-
Clears the authentication statistics for the specified interface name. If the string contains special characters (#, $, spaces, and so on), the entire string must be enclosed within double quotes.
- ip-address
-
Clears the authentication statistics for the specified IP address.
Platforms
All
statistics
Syntax
statistics [policy policy-id]
Context
[Tree] (clear>vrrp statistics)
Full Context
clear vrrp statistics
Description
Commands in this context clear and reset VRRP entities.
Parameters
- policy-id
-
Clears statistics for the specified policy.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>system>ptp statistics)
Full Context
show system ptp statistics
Description
This command displays the message and error statistics for the node.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of PTP statistics information, and System PTP statistics field descriptions describes the output fields.
Output Example# show system ptp statistics
===============================================================================
IEEE 1588/PTP Packet Statistics
===============================================================================
Input Output
-------------------------------------------------------------------------------
PTP Packets 0 0
Announce 0 0
Sync 0 0
Follow Up 0 0
Delay Request 0 0
Delay Response 0 0
Signaling 0 0
Request Unicast Transmission TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Grant Unicast Transmission (Accepted) TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Grant Unicast Transmission (Denied) TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Cancel Unicast Transmission TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Ack Cancel Unicast Transmission TLVs 0 0
Announce 0 0
Sync 0 0
Delay Response 0 0
Other TLVs 0 0
Other 0 0
Event Packets timestamped at port 0 0
Event Packets timestamped at cpm 0 0
Discards 0 0
Bad PTP domain 0 0
Alternate Master 0 0
Out Of Sequence 0 0
Peer Disabled 0 0
Packet Timing Signal Fail - Unusable 0 0
Other 0 0
===============================================================================
===============================================================================
IEEE 1588/PTP Frequency Recovery State Statistics
===============================================================================
State Seconds
-------------------------------------------------------------------------------
Initial 0
Acquiring 0
Phase-Tracking 0
Locked 0
Hold-over 0
===============================================================================
===============================================================================
IEEE 1588/PTP Event Statistics
===============================================================================
Event Sync Flow Delay Flow
-------------------------------------------------------------------------------
Packet Loss 0 0
Excessive Packet Loss 0 0
Excessive Phase Shift Detected 0 0
Too Much Packet Delay Variation - Freq 0 0
Too Much Packet Delay Variation - Time
===============================================================================
===============================================================================
IEEE 1588/PTP Clock Time Recovery State Statistics
===============================================================================
State Seconds
-------------------------------------------------------------------------------
Initial 1280
Acquiring 63
Locked 0
Hold-over 0
===============================================================================
===============================================================================
IEEE 1588/PTP Message Rates Per Second
===============================================================================
UDP/IP Ethernet
Packet Type Input Output Input Output
-------------------------------------------------------------------------------
Announce 0 0 0 0
Sync 0 0 0 0
Follow Up 0 0 0 0
Delay Request 0 0 0 0
Delay Response 0 0 0 0
Other 0 0 0 0
-------------------------------------------------------------------------------
Total 0 0 0 0
===============================================================================
Counter |
Counts |
|
---|---|---|
PTP Packets (packet type) |
Input |
The number of input packets for the specified packet type |
Output |
The number of output packets for the specified packet type |
|
Discards (reason type) |
Input |
The number of discarded input packets for the specified reason |
Output |
The number of discarded output packets for the specified reason |
|
State (state type) |
Seconds |
The number of seconds for the specified state type |
Event (event type) |
Sync Flow |
The number of sync flows for the specified event type |
Delay Flow |
The number of delay flows for the specified event type |
|
Packet Type (packet type) |
UDP/IP Input/Output |
The number of UDP/IP input or output packets for the specified packet type |
Ethernet Input/Output |
The number of Ethernet input or output packets for the specified packet type |
statistics
Syntax
statistics
Context
[Tree] (clear>application-assurance>group statistics)
Full Context
clear application-assurance group statistics
Description
This command clears application assurance statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
Context
[Tree] (clear>redundancy>multi-chassis>mcr statistics)
Full Context
clear redundancy multi-chassis mc-ring statistics
Description
This command clears multi-chassis ring.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>system>ptp statistics)
Full Context
clear system ptp statistics
Description
This command clears all PTP statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
statistics
Syntax
statistics
Context
[Tree] (clear>system statistics)
Full Context
clear system statistics
Description
This command clears system specific statistics.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>certificate statistics)
Full Context
show certificate statistics
Description
This command shows certificate related statistics.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>router>isis statistics)
Full Context
show router isis statistics
Description
This command displays information regarding IS-IS traffic statistics.
Platforms
All
Output
The following output is an example of IS-IS statistics output.
Output Example*A:Dut-C# show router isis statistics
===============================================================================
Rtr Base ISIS Instance 0 Statistics
===============================================================================
ISIS Instance : 0
Purge Initiated : 0 LSP Regens. : 17
Sid SRGB err : 0 Sid dupl err : 0
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
SPF Statistics
SPF Runs : 7
Last runTimeStamp: 01/26/2015 11:22:50
Partial SPF Runs : 3
Last runTimeStamp: 01/26/2015 11:22:51
LFA Statistics
LFA Runs : 7
Last runTimeStamp: 01/26/2015 11:22:51
Partial LFA Runs : 3
Last runTimeStamp: 01/26/2015 11:22:41
RLFA Statistics
RLFA Runs : 10
Last runTimeStamp: 01/26/2015 11:22:51
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 164 164 0 151 0
IIH 146 146 0 147 0
CSNP 288 288 0 291 0
PSNP 71 71 0 74 0
Unknown 0 0 0 0 0
===============================================================================
*A:Dut-C#
IS-IS Statistics Output Fields describes IS-IS statistics output fields.
Label |
Description |
---|---|
Purge Initiated |
The number of times purges have been initiated. |
SPF Runs |
The number of times shortest path first calculations have been made. |
LSP Regens |
The count of LSP regenerations. |
Requests |
The number of CSPF requests made to the protocol. |
Paths Found |
The number of responses to CSPF requests for which paths satisfying the constraints were found. |
PDU Type |
The PDU type. |
Received |
The count of link state PDUs received by this instance of the protocol. |
Processed |
The count of link state PDUs processed by this instance of the protocol. |
Dropped |
The count of link state PDUs dropped by this instance of the protocol. |
Sent |
The count of link state PDUs sent out by this instance of the protocol. |
Retransmitted |
The count of link state PDUs that had to be retransmitted by this instance of the protocol. |
statistics
statistics
Syntax
statistics
Context
[Tree] (show>router>ospf3 statistics)
[Tree] (show>router>ospf statistics)
Full Context
show router ospf3 statistics
show router ospf statistics
Description
This command displays the global OSPF statistics.
Platforms
All
Output
The following output is an example of global OSPF statistic information and OSPF Statistics Output Fields describes the output fields.
Output Exampleshow router ospf statistics
===============================================================================
Rtr Base OSPFv2 Instance 0 Statistics
===============================================================================
Rx Packets : 441 Tx Packets : 463
Rx Hellos : 361 Tx Hellos : 371
Rx DBDs : 9 Tx DBDs : 7
Rx LSRs : 3 Tx LSRs : 3
Rx LSUs : 54 Tx LSUs : 72
Rx LS Acks : 14 Tx LS Acks : 10
New LSAs Recvd : 57 New LSAs Orig : 8
Ext LSAs Count : 0 No of Areas : 1
No of Interfaces : 4 No of Neighbors : 3
Discards : 3 Tx Failures : 3
Retransmits : 2
Bad Networks : 0 Bad Virt Links : 0
Bad Areas : 0 Bad Dest Addrs : 0
Bad Auth Types : 0 Auth Failures : 0
Bad Neighbors : 0 Bad Pkt Types : 0
Bad Lengths : 0 Bad Hello Int. : 2
Bad Dead Int. : 1 Bad Options : 0
Bad Versions : 0 Bad Checksums : 0
SID SRGB errors : 0 SID dupl errors : 0
Failed SPF Attempts : 0 Bad MTUs : 0
CSPF Requests : 0 CSPF Request Drops : 0
CSPF Path Found : 0 CSPF Path Not Found : 0
Total SPF Runs : 6 Total LFA SPF Runs : 0
Total RLFA SPF Runs : 0 Total TI-LFA SPF Runs: 0
===============================================================================
show router ospf3 statistics
===============================================================================
Rtr Base OSPFv3 Instance 0 Statistics
===============================================================================
Rx Packets : 525 Tx Packets : 564
Rx Hellos : 387 Tx Hellos : 387
Rx DBDs : 8 Tx DBDs : 7
Rx LSRs : 3 Tx LSRs : 3
Rx LSUs : 113 Tx LSUs : 156
Rx LS Acks : 14 Tx LS Acks : 11
New LSAs Recvd : 77 New LSAs Orig : 12
Ext LSAs Count : 0 No of Areas : 1
No of Interfaces : 4 No of Neighbors : 3
Discards : 0 Tx Failures : 0
Retransmits : 0
Bad Networks : 0 Bad Virt Links : 0
Bad Areas : 0 Bad Dest Addrs : 0
Bad Auth Types : 0 Auth Failures : 0
Bad Neighbors : 0 Bad Pkt Types : 0
Bad Lengths : 0 Bad Hello Int. : 0
Bad Dead Int. : 0 Bad Options : 0
Bad Versions : 0 Bad Checksums : 0
SID SRGB errors : 0 SID dupl errors : 0
Failed SPF Attempts : 0 Bad MTUs : 0
CSPF Requests : 0 CSPF Request Drops : 0
CSPF Path Found : 0 CSPF Path Not Found : 0
Total SPF Runs : 7 Total LFA SPF Runs : 0
Total RLFA SPF Runs : 0 Total TI-LFA SPF Runs: 0
===============================================================================
Label |
Description |
---|---|
Rx Packets |
The total number of OSPF packets received on all OSPF enabled interfaces. |
Tx Packets |
The total number of OSPF packets transmitted on all OSPF enabled interfaces. |
Rx Hellos |
The total number of OSPF Hello packets received on all OSPF enabled interfaces. |
Tx Hellos |
The total number of OSPF Hello packets transmitted on all OSPF enabled interfaces. |
Rx DBDs |
The total number of OSPF database description packets received on all OSPF enabled interfaces. |
Tx DBDs |
The total number of OSPF database description packets transmitted on all OSPF enabled interfaces |
Rx LSRs |
The total number of OSPF Link State Requests (LSRs) received on all OSPF enabled interfaces. |
Tx LSRs |
The total number of OSPF Link State Requests (LSRs) transmitted on all OSPF enabled interfaces. |
Rx LSUs |
The total number of OSPF Link State Update (LSUs) received on all OSPF enabled interfaces. |
Tx LSUs |
The total number of OSPF Link State Update (LSUs) transmitted on all OSPF enabled interfaces. |
Rx LS Acks |
The total number of OSPF Link State Acknowledgments (LSAs) received on all OSPF enabled interfaces. |
New LSAs Recvd |
The total number of new OSPF Link State Advertisements received on all OSPF enabled interfaces. |
New LSAs Orig |
The total number of new OSPF Link State Advertisements originated on all OSPF enabled interfaces. |
Ext LSAs Count |
The total number of OSPF External Link State Advertisements. |
No of Areas |
The number of areas configured for this OSPF instance. |
Total SPF Runs |
The total number of incremental SPF runs triggered by new or updated LSAs. |
Ext SPF Runs |
The total number of incremental SPF runs triggered by new or updated type-5 external LSAs. |
Retransmits |
The total number of OSPF Retransmits transmitted on all OSPF enabled interfaces. |
Discards |
The total number of OSPF packets discarded on all OSPF enabled interfaces. |
Bad Networks |
The total number of OSPF packets received on all OSPF enabled interfaces with invalid network or mask. |
Bad Virt Links |
The total number of OSPF packets received on all OSPF enabled interfaces that are destined to a virtual link that does not exist. |
Bad Areas |
The total number of OSPF packets received on all OSPF enabled interfaces with an area mismatch. |
Bad Dest Addrs |
The total number of OSPF packets received on all OSPF enabled interfaces with the incorrect IP destination address. |
Bad Auth Types |
The total number of OSPF packets received on all OSPF enabled interfaces with an invalid authorization type. |
Auth Failures |
The total number of OSPF packets received on all OSPF enabled interfaces with an invalid authorization key. |
Bad Neighbors |
The total number of OSPF packets received on all OSPF enabled interfaces where the neighbor information does not match the information this router has for the neighbor. |
Bad Pkt Types |
The total number of OSPF packets received on all OSPF enabled interfaces with an invalid OSPF packet type. |
Bad Lengths |
The total number of OSPF packets received on all OSPF enabled interfaces with a total length not equal to the length given in the packet itself. |
Bad Hello Int. |
The total number of OSPF packets received on all OSPF enabled interfaces where the hello interval given in packet was not equal to that configured for the respective interface. |
Bad Dead Int. |
The total number of OSPF packets received on all OSPF enabled interfaces where the dead interval given in the packet was not equal to that configured for the respective interface. |
Bad Options |
The total number of OSPF packets received on all OSPF enabled interfaces with an option that does not match those configured for the respective interface or area. |
Bad Versions |
The total number of OSPF packets received on all OSPF enabled interfaces with bad OSPF version numbers. |
Tx Failures |
Transmitted OSPF packets that are dropped due to resource shortage. |
statistics
Syntax
statistics
Context
[Tree] (clear>router>ospf3 statistics)
[Tree] (clear>router>ospf statistics)
Full Context
clear router ospf3 statistics
clear router ospf statistics
Description
This command clears all neighbor, router, interface, SPF and global statistics of this OSPF instance.
Platforms
All
statistics
Syntax
statistics [ipv6-address | ip-int-name]
Context
[Tree] (show>router>ripng statistics)
Full Context
show router ripng statistics
Description
This command displays the interface level statistics for the RIPng protocol.
If no IPv6 address or interface name is specified, then all configured RIPng interfaces are displayed.
If an IPv6 address or interface name is specified, then only data regarding the specified RIPng interface is displayed.
Parameters
- ipv6-address | ip-int-name
-
Displays statistics for the specified IPv6 interface.
Platforms
All
Output
The following output are examples of RIPng statistics information.
Output Example*A:Dut-C>config>router>if# show router ripng statistics
===============================================================================
RIP-NG Statistics
===============================================================================
Learned Routes : 40 Timed Out Routes : 0
Current Memory : 1,199,016 Maximum Memory : 2,097,152
-------------------------------------------------------------------------------
Interface "one"
-------------------------------------------------------------------------------
Primary IP : 3ffe::10:10:3:3/1* Update Timer : 1
Timeout Timer : 5 Flush Timer : 5
Counter Total Last 5 Min Last 1 Min
-------------------------------------------------------------------------------
Updates Sent 221 180 5
Triggered Updates 0 0 0
Bad Packets Received 0 0 0
Updates Received 225 185 3
Updates Ignored 0 0 0
Bad Routes 0 0 0
Requests Received 0 0 0
Requests Ignored 0 0 0
-------------------------------------------------------------------------------
Interface "two"
-------------------------------------------------------------------------------
Primary IP : 3ffe::10:10:103:3* Update Timer : 1
Timeout Timer : 5 Flush Timer : 5
Counter Total Last 5 Min Last 1 Min
-------------------------------------------------------------------------------
Updates Sent 220 183 5
Triggered Updates 0 0 0
Bad Packets Received 0 0 0
Updates Received 229 183 5
Updates Ignored 0 0 0
Bad Routes 0 0 0
Requests Received 0 0 0
Requests Ignored 0 0 0
-------------------------------------------------------------------------------
Interface "three"
-------------------------------------------------------------------------------
Primary IP : 3ffe::10:10:12:3/* Update Timer : 1
Timeout Timer : 5 Flush Timer : 5
Counter Total Last 5 Min Last 1 Min
-------------------------------------------------------------------------------
Updates Sent 224 184 6
Triggered Updates 0 0 0
Bad Packets Received 0 0 0
Updates Received 221 182 4
Updates Ignored 0 0 0
Bad Routes 0 0 0
Requests Received 0 0 0
Requests Ignored 0 0 0
-------------------------------------------------------------------------------
Interface "four"
-------------------------------------------------------------------------------
Primary IP : 3ffe::10:10:112:3* Update Timer : 1
Timeout Timer : 5 Flush Timer : 5
Counter Total Last 5 Min Last 1 Min
-------------------------------------------------------------------------------
Updates Sent 220 182 8
Triggered Updates 0 0 0
Bad Packets Received 0 0 0
Updates Received 227 185 4
Updates Ignored 0 0 0
Bad Routes 0 0 0
Requests Received 0 0 0
Requests Ignored 0 0 0
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-C>config>router>if# show router ripng statistics "one"
===============================================================================
RIP-NG Statistics
===============================================================================
Learned Routes : 40 Timed Out Routes : 0
Current Memory : 1,199,016 Maximum Memory : 2,097,152
-------------------------------------------------------------------------------
Interface "one"
-------------------------------------------------------------------------------
Primary IP : 3ffe::10:10:3:3/1* Update Timer : 1
Timeout Timer : 5 Flush Timer : 5
Counter Total Last 5 Min Last 1 Min
-------------------------------------------------------------------------------
Updates Sent 224 183 8
Triggered Updates 0 0 0
Bad Packets Received 0 0 0
Updates Received 230 190 8
Updates Ignored 0 0 0
Bad Routes 0 0 0
Requests Received 0 0 0
Requests Ignored 0 0 0
===============================================================================
* indicates that the corresponding row element may have been truncated.
statistics
Syntax
statistics
statistics manager all
statistics manager manager-name
Context
[Tree] (clear>system>management-interface>remote-management statistics)
Full Context
clear system management-interface remote-management statistics
Description
This command clears the statistics for remote management managers. If the command is run without specifying the manager, the statistics for all remote managers are cleared.
Parameters
- manager
-
Keyword to specify that clears statistics only for a specific manager.
- manager-name
-
Specifies the configured name of the manager, up to 64 characters, for which the statistics are cleared.
- all
-
Clears statistics for all managers.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (show>subscr-mgmt>pfcp statistics)
Full Context
show subscriber-mgmt pfcp statistics
Description
This command displays the packet counters for each PFCP message and upstream IBCP message.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of PFCP statistics information.
Output ExampleA:BNG-UPF# show subscriber-mgmt pfcp statistics
===============================================================================
PFCP System Statistics
===============================================================================
PFCP Session Related Messages
Session Establish Req : 3 Session Establish Resp : 3
Session Establish Resp fail: 0
Session Modify Req : 2 Session Modify Resp : 2
Session Modify Resp fail : 0
Session Deletion Req : 1 Session Deletion Resp : 1
Session Deletion Resp fail : 0
Session Report Req : 1 Session Report Resp : 1
Session Report Resp fail : 0
Session Report DDR Req : 0 Session Report DDR Rsp : 0
Session Report DDR Rsp fail: 0
Session Report UR Req : 0 Session Report UR Rsp : 0
Session Report UR Rsp fail : 0
Session Report EIR Req : 0 Session Report EIR Rsp : 0
Session Report EIR Rsp fail: 0
Session Report UPIR Req : 1 Session Report UPIR Rsp : 1
Session Report UPIR Rs fail: 0
PFCP Session Audit Related Messages
Session Modify Req : 0 Session Modify Resp : 0
Session Modify Resp fail : 0
Session Report Req : 0 Session Report Rsp : 0
Session Report Rsp fail : 0
PFCP Node Related Messages
Node Report Req : 0 Node Report Resp : 0
Node Report Resp fail : 0
Assoc Setup Req Rx : 0 Assoc Setup Resp Rx : 1
Assoc Setup Resp fail Rx : 0
Assoc Setup Req Tx : 1 Assoc Setup Resp Tx : 0
Assoc Setup Resp fail Tx : 0
Assoc Upd Req Rx : 0 Assoc Upd Resp Rx : 0
Assoc Upd Resp fail Rx : 0
Assoc Upd Req Tx : 0 Assoc Upd Resp Tx : 0
Assoc Upd Resp fail Tx : 0
Assoc Upd Req with ARR : 0 Assoc Upd Req with GRP : 0
Assoc Upd Req ARR & GRP : 0
Assoc Release Req : 0 Assoc Release Resp : 0
Assoc Release Resp fail : 0
Heartbeat Req Rx : 417 Heartbeat Resp Rx : 1
Heartbeat Req Tx : 1 Heartbeat Resp Tx : 417
Heartbeat Aud Trig Req Tx : 0 Heartbeat Aud Trig Rsp Rx : 0
Heartbeat Aud Start Req Rx : 0 Heartbeat Aud Start Rsp Tx : 0
Heartbeat Aud End Req Rx : 0 Heartbeat Aud End Rsp Tx : 0
IBCP upstream packet statistics
Ipoe Rx Pkts : 0
Pppoe Ctrl Rx Pkts : 10
Pppoe Data Rx Pkts : 16
Tx Pkts to Smf : 26
IBCP upstream packet discard statistics
Missing pkt detection rule : 0
Default tnl trigger missing: 0
Default tunnel missing : 0
Parsing error : 0
Tx error : 0
IBCP default tunnel
overwrite : 0
Number of PFCP Sessions : 2
-------------------------------------------------------------------------------
===============================================================================
statistics
Syntax
statistics lsp-path [lsp-index lsp-index] [path-lspid path-lspid ][prefix ip-prefix/prefix-length] [ src ip-address | ipv6 address]
statistics lsp-path all
statistics sr-policy [lsp-index lsp-index] [path-lspid path-lspid] [prefix ip-prefix/prefix-length] [ src ip-address | ipv6 address]
statistics sr-policy all
Context
[Tree] (clear>router>bfd>seamless-bfd statistics)
Full Context
clear router bfd seamless-bfd statistics
Description
This command clears BFD statistics.
Parameters
- lsp-path
-
Keyword to clear the S-BFD statistics for LSP path.
- sr-policy
-
Keyword to clear the S-BFD statistics for SR policy.
- all
-
Keyword to clear all S-BFD statistics.
- lsp-index lsp-index
-
Specifies the LSP index.
- path-lspid path-lspid
-
Specifies the path LSP ID.
- prefix
-
Keyword to clear information by far-end prefix.
- ip-prefix/prefix-length
-
Specifies an IP prefix for which to clear S-BFD statistics, and the length of the prefix.
- ip-address | ipv6-address
-
Specifies the IP address for which to clear S-BFD statistics.
Platforms
All
statistics
Syntax
statistics [interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor>router>isis statistics)
Full Context
monitor router isis statistics
Description
This command displays statistical IS-IS traffic information at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the specified router statistics. The subsequent statistical information listed for each interval is displayed as a delta to the previous display. When the keyword rate is specified, the rate-per-second for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor commands display the selected statistics according to the configured number of times at the interval specified.
Parameters
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
All
Output
The following output is an example of ISIS statistics.
Output ExampleA:ALA-12>monitor>router>isis# statistics interval 3 repeat 2 absolute
===============================================================================
ISIS Statistics
===============================================================================
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
ISIS Instance : 1 SPF Runs : 2
Purge Initiated : 0 LSP Regens. : 11
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 74 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Absolute)
-------------------------------------------------------------------------------
ISIS Instance : 1 SPF Runs : 2
Purge Initiated : 0 LSP Regens. : 11
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 74 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Absolute)
-------------------------------------------------------------------------------
ISIS Instance : 1 SPF Runs : 2
Purge Initiated : 0 LSP Regens. : 11
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 74 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
===============================================================================
A:ALA-12>monitor>router>isis# statistics interval 3 repeat 2 rate
===============================================================================
ISIS Statistics
===============================================================================
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
ISIS Instance : 1 SPF Runs : 2
Purge Initiated : 0 LSP Regens. : 11
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 76 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Rate)
-------------------------------------------------------------------------------
ISIS Instance : 1 SPF Runs : 0
Purge Initiated : 0 LSP Regens. : 0
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 0 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Rate)
-------------------------------------------------------------------------------
ISIS Instance : 1 SPF Runs : 0
Purge Initiated : 0 LSP Regens. : 0
CSPF Statistics
Requests : 0 Request Drops : 0
Paths Found : 0 Paths Not Found: 0
-------------------------------------------------------------------------------
PDU Type Received Processed Dropped Sent Retransmitted
-------------------------------------------------------------------------------
LSP 0 0 0 0 0
IIH 0 0 0 1 0
CSNP 0 0 0 0 0
PSNP 0 0 0 0 0
Unknown 0 0 0 0 0
===============================================================================
A:ALA-12>monitor>router>isis#
statistics
Syntax
statistics [interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor>router>ldp statistics)
Full Context
monitor router ldp statistics
Description
Monitor statistics for LDP instance at the configured interval until the configured count is reached.
The first screen displays the current statistics related to the LDP statistics. The subsequent statistical information listed for each interval is displayed as a delta to the previous display. When the keyword rate is specified, the rate-per-second for each statistic is displayed instead of the delta.
Monitor commands are similar to show commands but only statistical information displays. Monitor commands display the selected statistics according to the configured number of times at the interval specified.
Parameters
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
All
Output
The following output is an example of LDP statistics information.
Output ExampleA:ALA-12>monitor>router>ldp# statistics interval 3 repeat 3 absolute
===============================================================================
Monitor statistics for LDP instance
===============================================================================
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 1 Serv FECs Recv : 2
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Absolute)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 1 Serv FECs Recv : 2
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Absolute)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 1 Serv FECs Recv : 2
-------------------------------------------------------------------------------
At time t = 9 sec (Mode: Absolute)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 1 Serv FECs Recv : 2
===============================================================================
A:ALA-12>monitor>router>ldp#
A:ALA-12>monitor>router>ldp# statistics interval 3 repeat 3 rate
===============================================================================
Monitor statistics for LDP instance
===============================================================================
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 1 Serv FECs Recv : 2
-------------------------------------------------------------------------------
At time t = 3 sec (Mode: Rate)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 0 Serv FECs Recv : 0
-------------------------------------------------------------------------------
At time t = 6 sec (Mode: Rate)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 0 Serv FECs Recv : 0
-------------------------------------------------------------------------------
At time t = 9 sec (Mode: Rate)
-------------------------------------------------------------------------------
Addr FECs Sent : 0 Addr FECs Recv : 0
Serv FECs Sent : 0 Serv FECs Recv : 0
===============================================================================
A:ALA-12>monitor>router>ldp#
statistics
Syntax
statistics [interval seconds] [ repeat repeat] [absolute| rate]
Context
[Tree] (monitor>eth-cfm statistics)
Full Context
monitor eth-cfm statistics
Description
This command monitors control plane traffic statistics.
Parameters
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
statistics
Syntax
statistics all
statistics neighbor ip-address [port port-number]
Context
[Tree] (clear>service>id>gsmp statistics)
Full Context
clear service id gsmp statistics
Description
This command clears General Switch Management Protocol (GSMP) statistics.
Parameters
- all
-
Clears all GSMP related statistics.
- ip-address
-
Specifies the IP address.
- port-number
-
Specifies port number.
Platforms
All
statistics
Syntax
statistics
Context
[Tree] (clear>system>ptp>port statistics)
Full Context
clear system ptp port statistics
Description
This command clears PTP port statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
statistics
Syntax
statistics
Context
[Tree] (clear>service>id>subhosts statistics)
Full Context
clear service id subscriber-hosts statistics
Description
This command clears subscriber host HTTP redirect statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
Context
[Tree] (show>li>x-interfaces statistics)
Full Context
show li x-interfaces statistics
Description
Commands in this context display statistics of the X1, X2, and X3 interfaces.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
statistics
Syntax
statistics
Context
[Tree] (clear>router>bier statistics)
Full Context
clear router bier statistics
Description
This command clears BIER statistics.
Platforms
All
statistics
Syntax
statistics [policy policy-name]
Context
[Tree] (clear>router>mcac statistics)
Full Context
clear router mcac statistics
Description
This command clears and resets MCAC statistics.
Parameters
- policy-name
-
Specifies the policy name, up to 32 characters.
Platforms
All
statistics
Syntax
statistics [portal name] [ all-portals]
Context
[Tree] (clear>router>wpp statistics)
Full Context
clear router wpp statistics
Description
This command clears WPP statistics.
Parameters
- portal-name
-
Specifies the portal name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
statistics
Syntax
statistics
Context
[Tree] (clear>router>autoconfigure>rtr-adv statistics)
Full Context
clear router autoconfigure router-advertisement statistics
Description
This command clears router-advertisement statistics.
Platforms
7450 ESS-7, 7750 SR-1, 7750 SR-7, 7750 SR-1e, 7750 SR-2e, 7750 SR-s
statistics-summary
statistics-summary
Syntax
statistics-summary [active] [family]
Context
[Tree] (show>router>ldp statistics-summary)
Full Context
show router ldp statistics-summary
Description
This command displays LDP statistics summary information.
Parameters
- active
-
Displays LDP statistics for only active paths.
- family
-
Displays either IPv4 or IPv6 LDP information.
Platforms
All
Output
Output Example*A:Dut-A# show router ldp statistics-summary
===============================================================================
Statistics Summary
===============================================================================
LDP FEC IPv4 Prefix Egress statistics : 0
LDP FEC IPv6 Prefix Egress statistics : 0
===============================================================================
*A:Dut-A#
statistics-summary
Syntax
statistics-summary
Context
[Tree] (show>router>mpls statistics-summary)
Full Context
show router mpls statistics-summary
Description
This command displays the number of LSP statistics configured.
Platforms
All
Output
The following output is an example of MPLS statistics summary information.
Output Example*A:SRU4>config>router>mpls# show router mpls statistics-summary
===============================================================================
Statistics Summary
===============================================================================
LSP egress statistics : 0
LSP ingress statistics : 0
===============================================================================
*A:SRU4>config>router>mpls#
stats
stats
Syntax
stats
Context
[Tree] (tools>dump>ipsec stats)
Full Context
tools dump ipsec stats
Description
Commands in this context dump the IPsec statistics.
Platforms
All
stats
Syntax
stats
Context
[Tree] (clear>ipsec stats)
Full Context
clear ipsec stats
Description
Commands in this context clear IKE statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
status
status
Syntax
status
Context
[Tree] (show>call-trace status)
Full Context
show call-trace status
Description
This command gives a router-wide overview of call-trace operational data, such as number of configured profile, number of jobs and status of the compact flash.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of call trace status information.
Output Example===============================================================================
Call trace status
===============================================================================
No. of trace profiles: 1
No. of trace jobs : 0
-------------------------------------------------------------------------------
Primary CF : CF1 Max files number : 200
CF1 state : enabled CF1 volume limit : 1000 MB
CF2 state : enabled CF2 volume limit : 1000 MB
Call Trace Status Field Descriptions describes call trace status output field information.
Field |
Descriptions |
---|---|
No. of trace profiles |
The number of profiles configured in the system |
No. of trace jobs |
The number of trace jobs |
Primary CF |
The compact flash card to be used as the primary local storage location to save the generated call trace log files |
Max files number |
The cumulative number of call trace log files present on all cflash cards on the active CPM that are being used for local storage has reached the limit |
CF1 state |
The status of a call trace job on CF2. "running” indicates the job is active and is tracing events triggered by the host being monitored. "finished” indicates the job has already finished and is not tracing events generated by the host anymore. |
CF1 volume limit |
The data volume limit for the CF1 call trace job |
CF2 state |
The status of a call trace job on CF2. "running” indicates the job is active and is tracing events triggered by the host being monitored. "finished” indicates the job has already finished and is not tracing events generated by the host anymore. |
CF2 volume limit |
The data volume limit for the CF2 call trace job |
status
Syntax
status
Context
[Tree] (show>router>igmp status)
Full Context
show router igmp status
Description
This command displays IGMP status information.
If IGMP is not enabled, the following message appears:
A:NYC# show router igmp status
MINOR: CLI IGMP is not configured.
A:NYC#
Platforms
All
Output
The following output is an example of IGMP status information. IGMP Status Fields provides IGMP status field descriptions.
Output Example*A:ALA-BA# show router 100 igmp status
===============================================================================
IGMP Status
===============================================================================
Admin State : Up
Oper State : Up
Query Interval : 1024
Last Member Query Interval : 1024
Query Response Interval : 1023
Robust Count : 10
===============================================================================
*A:ALA-BA#
Label |
Description |
---|---|
Admin State |
The administrative status of IGMP. |
Oper State |
The current operating state of this IGMP protocol instance on this router. |
Query Interval |
The frequency at which IGMP query packets are transmitted. |
Last Member Query Interval |
The maximum response time inserted into group-specific queries sent in response to leave group messages, and is also the amount of time between group-specific query messages. |
Query Response Interval |
The maximum query response time advertised in IGMPv2 queries. |
Robust Count |
The number of times the router will retry a query. |
status
Syntax
status
Context
[Tree] (show>service>id>spb status)
Full Context
show service id spb status
Description
This command displays SPB status.
Platforms
All
Output
The following output is an example of service SPB status information.
Output ExampleA:cses-B01# show service id spb status
===============================================================================
ISIS Status
===============================================================================
System Id : 0000.00AA.AAAA
Admin State : Up
Oper State : Up
SPB Routing : Enabled
Last Enabled : 07/23/2012 16:01:06
Level Capability : L1
Authentication Check : True
Authentication Type : None
CSNP-Authentication : Enabled
HELLO-Authentication : Enabled
PSNP-Authentication : Enabled
Overload-On-Boot Tim*: 0
LSP Lifetime : 1200
LSP Wait : 5 sec (Max) 0 sec (Initial) 1 sec (Second)
LSP MTU Size : 1492 (Config) 1492 (Oper)
Adjacency Check : loose
L1 Auth Type : none
L1 CSNP-Authenticati*: Enabled
L1 HELLO-Authenticat*: Enabled
L1 PSNP-Authenticati*: Enabled
L1 Preference : 15
L1 Ext. Preference : 160
L1 Wide Metrics : Enabled
L1 LSDB Overload : Disabled
L1 LSPs : 4
L1 Default Metric : 10
L1 IPv6 Def Metric : 10
Last SPF : 07/23/2012 16:01:29
SPF Wait : 10 sec (Max) 1000 ms (Initial) 1000 ms (Second)
Multi-topology : Disabled
Area Addresses : 00
Total Exp Routes(L1) : 0
IID TLV : Disabled
All-L1-MacAddr : 01:80:c2:00:00:14
===============================================================================
status
Syntax
status [family]
Context
[Tree] (show>service>id>pim-snooping status)
Full Context
show service id pim-snooping status
Description
This command displays PIM status information.
Parameters
- family
-
Displays either IPv4 or IPv6 status information
Platforms
All
Output
The following output is an example of service PIM snooping status information.
Output Example*A:PE# show service id 1 pim-snooping status
===============================================================================
PIM Snooping Status ipv4
===============================================================================
Admin State : Up
Oper State : Up
Mode Admin : Proxy
Mode Oper : Proxy
Hold Time : 90
Designated Router : 10.0.1.2
J/P Tracking : Inactive
Up Time : 0d 00:08:43
Group Policy : None
===============================================================================
*A:PE#
status
Syntax
status
Context
[Tree] (show>router>ldp status)
Full Context
show router ldp status
Description
This command displays LDP status information.
Platforms
All
Output
LDP Status Output
LDP Status Output Fields describes the LDP status output fields.
Output Example*A:Sim>config>router>ldp# show router ldp status
===============================================================================
LDP Status for IPv4 LSR ID 0.0.0.0
IPv6 LSR ID ::
===============================================================================
Created at : 02/01/22 16:19:46
Last Change : 02/01/22 16:19:46
Admin State : Up
IPv4 Oper State : Down IPv6 Oper State : Down
IPv4 Down Time : 2d 03:47:02 IPv6 Down Time : 2d 03:47:02
IPv4 Oper Down Rea*: systemIpDown IPv6 Oper Down Reason: systemIpDown
IPv4 Oper Down Eve*: 0 IPv6 Oper Down Events: 0
Tunn Down Damp Time: 3 sec Weighted ECMP : Disabled
Tunnel Table Pref : 9
Label Withdraw Del*: 0 sec Implicit Null Label : Disabled
Short. TTL Local : Enabled Short. TTL Transit : Enabled
ConsiderSysIPInGep : Disabled
Imp Ucast Policies : None Exp Ucast Policies : None
Imp Mcast Policies : None
Tunl Exp Policies : None Tunl Imp Policies : None
FRR : Disabled Mcast Upstream FRR : Disabled
Mcast Upst ASBR FRR: Disabled ASBR MoFRR Loop Detct: Disabled
MP MBB Time : 3
Aggregate Prefix : False Agg Prefix Policies : None
Class Forwarding : Disabled
Legacy LSR Interop : False
Entropy Label Capa*: False
Generate Basic FEC : Disabled
Resolve Root Using : ucastRtm
Import PMSI Routes : None
Cfg Max ECMP Routes: 32 Oper ECMP : 1
-------------------------------------------------------------------------------
Capabilities
-------------------------------------------------------------------------------
Dynamic : Enabled P2MP : Enabled
IPv4 Prefix Fec : Enabled IPv6 Prefix Fec : Enabled
Service Fec128 : Enabled Service Fec129 : Enabled
MP MBB : Enabled Overload : Enabled
Unrecognized Notif*: Enabled
===============================================================================
Label |
Description |
---|---|
Created at |
The date and time when the LDP instance was created. |
Last Change |
The date and time when the LDP instance was last modified. |
Admin State |
Up — The LDP is administratively enabled. Down — The LDP is administratively disabled. |
Oper State |
Up — The LDP is operationally enabled. Down — The LDP is operationally disabled. |
Up Time |
The time, in hundredths of seconds, that the LDP instance has been operationally up. |
Oper Down Reason |
The reason for the operational down status. |
Oper Down Events |
The number of times the LDP instance has gone operationally down since the instance was created. |
Tunn Down Damp Time |
Indicates the value configured by tunnel-down-damp-time. |
Weighted ECMP |
Indicates whether weighted ecmp is enabled or not. |
Label Withdraw Del* |
Indicates the value configured by label-withdrawal-delay. |
Implicit Null Label |
Indicates whether implicit null is supported. |
Short. TTL Local |
Indicates whether shortcut-local-ttl-propagate is enabled or not. |
Short. TTL Transit |
Indicates whether shortcut-transit-ttl-propagate is enabled or not. |
ConsiderSysIPByPol* |
Whether consider-system-ip-in-gep is enabled. |
Imp Ucast Policies |
Lists the applied import unicast policies, if any. Up to five import policies can be specified. |
Exp Ucast Policies |
Lists the applied export unicast policies, if any. Up to five import policies can be specified. |
Imp Mcast Policies |
Lists the applied import multicast policies, if any. Up to five import policies can be specified. |
Tunl Exp Policies |
Lists the applied tunnel export policies, if any. Up to five import policies can be specified. |
FRR |
Indicates whether Fast ReRoute is enabled or not. |
Mcast Upstream FRR |
Indicates whether multicast upstream fast reroute has been enabled or not. |
Mcast Upst ASBR FRR |
Indicates whether multicast upstream fast reroute has been enabled or not at ASBR. |
MP MBB Time |
Indicates the value configured by mp-mbb-time. |
Aggregate Prefix |
Indicates whether aggregate-prefix-match has been enabled or not. |
Agg Prefix Policies |
Lists the policies for the aggregate prefix match, if any. Up to five aggregate prefix policies can be specified. |
Class Forwarding |
Indicates whether class forwarding is in the enabled or disabled mode. Enabled modes are (lsr, ler, or lsr-and-ler). |
Legacy LSR Interop |
Indicates whether legacy LSR interoperability has been enabled or not. |
Entropy Label Capa* |
Indicates whether the support for entropy label is enabled or not. |
Generate Basic FEC |
Indicates whether generate-basic-fec-only has been enabled or not. |
Resolve Via Mcast * |
Indicates whether the route for the root address of P2MP FECs will be resolved using the unicast routing table or the multicast routing table. |
Capabilities |
|
Dynamic |
Indicates whether LDP supports changing capabilities dynamically using the LDP Capability message, or only in the Initialization message. |
P2MP |
Indicates whether LDP supports exchanging P2MP FECs. |
IPv4 Prefix Fec |
Indicates whether LDP supports exchanging IPv4 Prefix FECs. |
IPv6 Prefix Fec |
Indicates whether LDP supports exchanging IPv6 Prefix FECs. |
Service Fec128 |
Indicates whether LDP supports exchanging basic pseudowire service FECs. |
Service Fec129 |
Indicates whether LDP supports exchanging generalized pseudowire (PWE3) service FECs. |
MP MBB |
Indicates whether MP MBB is enabled or not. |
Overload |
Indicates whether LDP supports sending and receiving overload notification messages (Nokia vendor extension). |
Unrecognized Notif* |
Indicates whether LDP supports receiving notification messages with an unrecognized status; required for the end-of-lib feature (RFC 5919). |
status
Syntax
status
Context
[Tree] (show>router>mpls status)
Full Context
show router mpls status
Description
This command displays MPLS operation information.
Platforms
All
Output
The following output is an example of MPLS status information.
MPLS Status Output Fields describes MPLS status output fields.
Output Example# show router mpls status
===============================================================================
MPLS Status
===============================================================================
Admin Status : Up
Oper(V4) State : Up Oper(V6) State : Up
IPv4 Oper Down Reason : n/a
IPv6 Oper Down Reason : n/a
FRR Object : Enabled Resignal Timer : Disabled
Hold Timer : 1 seconds Next Resignal : N/A
Srlg Frr : Disabled Srlg Frr Strict : Disabled
Admin Group Frr : Disabled
Dynamic Bypass : Enabled User Srlg Database : Disabled
BypassResignalTimer : Disabled BypassNextResignal : N/A
LeastFill Min Thd : 5 percent LeastFill Reopti Thd : 10 percent
Local TTL Prop : Enabled Transit TTL Prop : Enabled
P2mp TTL Prop : Disabled
AB Sample Multiplier : 1 AB Adjust Multiplier : 288
Exp Backoff Retry : Disabled CSPF On Loose Hop : Disabled
Lsp Init RetryTimeout : 30 seconds MBB Pref Current Hops : Disabled
Logger Event Bundling : Disabled
Retry on IGP Overload : Disabled Resignal on IGP Overload : Enabled
P2mp Resignal Timer : Disabled P2mp Next Resignal : N/A
Sec FastRetryTimer : Disabled Static LSP FR Timer : 30 seconds
P2P Max Bypass Association: 1000
Max Bypass PLR Association: 16
P2PActPathFastRetry : Disabled P2MP S2L Fast Retry : Disabled
In Maintenance Mode : No
MplsTp : Disabled
Next Available Lsp Index : 2
Entropy Label RSVP-TE : Enabled Entropy Label SR-TE : Enabled
PCE Report RSVP-TE : Disabled PCE Report SR-TE : Disabled
PCE Init LSP : Disabled
SR-TE Resignal Timer : Disabled SR-TE Resig on IGP Event : Disabled
LSP Self Ping Timeout : 300 seconds LSP Self Ping Interval : 2 seconds
LSP Self Ping RSVP TE : Enabled
===============================================================================
MPLS LSP Count
===============================================================================
Originate Transit Terminate
-------------------------------------------------------------------------------
Static LSPs 0 0 0
Dynamic LSPs 1 0 0
Detour LSPs 0 0 0
P2MP S2Ls 0 0 0
MPLS-TP LSPs 0 0 0
Mesh-P2P LSPs 0 N/A N/A
One Hop-P2P LSPs 0 N/A N/A
SR-TE LSPs 0 N/A N/A
Mesh-P2P SR-TE LSPs 0 N/A N/A
One Hop-P2P SR-TE LSPs 0 N/A N/A
PCE Init SR-TE LSPs 0 N/A N/A
===============================================================================
Label |
Description |
---|---|
Admin Status |
Down — MPLS is administratively disabled. Up — MPLS is administratively enabled. |
Oper Status |
Down — MPLS is operationally down. Up — MPLS is operationally up. |
Oper Down Reason |
Specifies the operational down cause. |
FRR Object |
Enabled — Specifies that Fast reroute object is signaled for the LSP. Disabled — Specifies that Fast reroute object is not signaled for the LSP. |
Resignal Timer |
Enabled — Specifies that the resignal timer is enabled for the LSP. Disabled — Specifies that the resignal timer is disabled for the LSP. |
Hold Timer |
Displays the amount of time that the ingress node holds before programming its data plane and declaring the LSP up to the service module. |
Next Resignal |
Specifies the next resignal value. |
Srlg Frr |
Enabled — Specifies that SRLG Fast reroute is signaled for the LSP. Disabled — Specifies that SRLG Fast reroute is not signaled for the LSP. |
Srlg Frr Strict |
Enabled — Specifies that SRLG Fast reroute strict is signaled for the LSP. Disabled — Specifies that SRLG Fast reroute strict is not signaled for the LSP. |
Admin Group Frr |
Enabled — Specifies that the administrative group Fast reroute is signaled for the LSP. Disabled — Specifies that the administrative group Fast reroute is not signaled for the LSP. |
Dynamic Bypass |
Enabled — Specifies that dynamic bypass is enabled. Disabled — Specifies that dynamic bypass is disabled. |
User Srlg Database |
Enabled — Specifies that user SRLG databases are enabled. Disabled — Specifies that user SRLG databases are disabled. |
BypassResignalTimer |
Enabled — Specifies that the bypass resignal timer is enabled. Disabled — Specifies that the bypass resignal timer is disabled. |
BypassNextResignal |
Specifies the bypass next resignal value. |
LeastFill Min Thd |
Specifies the least fill minimum threshold percentage value. |
LeastFill Reopti Thd |
Specifies the least fill re-optimization threshold percentage value. |
Local TTL Prop |
Enabled — Specifies that local TTL property is enabled. Disabled — Specifies that local TTL property is disabled. |
Transit TTL Prop |
Enabled — Specifies that transit TTL property is enabled. Disabled — Specifies that transit TTL property is disabled. |
P2mp TTL Prop |
Enabled — Specifies that the uniform mode of operation is configured for RSVP P2MP LSPs. Disabled — Specifies that the pipe mode of operation is configured for RSVP P2MP LSPs. |
AB Sample Multiplier |
Specifies the AB sample multiplier value. |
AB Adjust Multiplier |
Specifies the AB adjust multiplier value. |
Exp Backoff Retry |
Enabled — Specifies that Exp Backoff retry is enabled. Disabled — Specifies that Exp Backoff is disabled. |
CSPF On Loose Hop |
Enabled — Specifies that CSPF On Loose Hop is enabled. Disabled — Specifies that CSPF On Loose Hop is disabled. |
Lsp Init RetryTimeout |
Specifies the LSP Init RetryTimeout seconds value. |
MBB Pref Current Hops |
Enabled — Specifies that MBB Pref Current Hops is enabled. Disabled — Specifies that MBB Pref Current Hops is disabled. |
Logger Event Bundling |
Enabled — Specifies that Logger Event Bundling is enabled. Disabled — Specifies that Logger Event Bundling is disabled. |
Retry on IGP Overload |
Enabled — Specifies that Retry on IGP Overload is enabled. Disabled — Specifies that Retry on IGP Overload is disabled. |
Resignal on IGP Overload |
Enabled — Specifies that Resignal on IGP Overload is enabled. Disabled — Specifies that Resignal on IGP Overload is disabled. |
P2mp Resignal Timer |
Enabled — Specifies that the P2MP Resignal Timer is enabled. Disabled — Specifies that the P2MP Resignal Timer is disabled. |
P2mp Next Resignal |
Specifies the P2MP Next Resignal Timer value. |
Sec FastRetryTimer |
Enabled — Specifies that the Sec Fast RetryTimer is enabled. Disabled — Specifies that the Sec Fast RetryTimer is disabled. |
Static LSP FR Timer |
Specifies the Static LSP FR Timer seconds value. |
P2P Max Bypass Association |
Specifies the P2P Max Bypass Association value. |
P2PActPathFastRetry |
Enabled — Specifies that the P2P ActPath Fast Retry is enabled. Disabled — Specifies that the P2P ActPath Fast Retry is disabled. |
P2MP S2L Fast Retry |
Enabled — Specifies that the P2MP S2L Fast Retry is enabled. Disabled — Specifies that the P2MP S2L Fast Retry is disabled. |
In Maintenance Mode |
No — Specifies that the system is not in maintenance mode. Yes — Specifies that the system is in maintenance mode. |
MplsTp |
Enabled — Specifies that MPLS TP is enabled. Disabled — Specifies that MPLS TP is disabled. |
Next Available Lsp Index |
Specifies the next available LSP index value. |
Entropy Label RSVP-TE |
Enabled — Specifies that Entropy Label RSVP-TE is enabled. Disabled — Specifies that Entropy Label RSVP-TE is disabled. |
Entropy Label SR-TE |
Enabled — Specifies that Entropy Label SR-TE is enabled. Disabled — Specifies that Entropy Label SR-TE is disabled. |
PCE Report RSVP-TE |
Enabled — Specifies that PCE Report RSVP-TE is enabled. Disabled — Specifies that PCE Report RSVP-TE is disabled. |
PCE Report SR-TE |
Enabled — Specifies that PCE Report SR-TE is enabled. Disabled — Specifies that PCE Report SR-TE is disabled. |
PCE Init LSP |
Enabled — Specifies that PCE Init LSP is enabled. Disabled — Specifies that PCE Init LSP is disabled. |
PCE Init SR-TE |
Enabled — Specifies that PCE Init LSP SR-TE is enabled. Disabled — Specifies that PCE Init LSP SR-TE is disabled. |
PCE Init SR-TE Admin State |
Up — Specifies that the PCE Init SR-TE Admin State is up. Down — Specifies that the PCE Init SR-TE Admin State is down. |
PCE Init SR-TE Oper State |
Up — Specifies that the PCE Init SR-TE Operational State is up. Down — Specifies that the PCE Init SR-TE Operational State is down. |
PCE Init SR-TE Oper Dn Rsn |
Specifies the reason for the PCE Init SR-TE Operationally down. |
LSP Self Ping Timeout |
Specifies the LSP Self Ping timeout value. |
LSP Self Ping Interval |
Specifies the LSP Self Ping interval value. |
LSP Self Ping RSVP TE |
Specifies the status of LSP Self Ping RSVP TE. |
Originate |
Specifies the number of originations for the various LSP types. |
Transit |
Specifies the number of transits for the various LSP types. |
Terminate |
Specifies the number of terminations for the various LSP types. |
status
Syntax
status
Context
[Tree] (show>router>mpls>mpls-tp status)
Full Context
show router mpls mpls-tp status
Description
This command displays MPLS-TP system configuration information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of MPLS TP status information .
Output Example*A:mlstp-dutA# show router mpls mpls-tp status
===============================================================================
MPLS-TP Status
===============================================================================
Admin Status : Up
Global ID : 42 Node ID : 0.0.3.233
Tunnel Id Min : 1 Tunnel Id Max : 4096
===============================================================================
status
Syntax
status
Context
[Tree] (show>router>rsvp status)
Full Context
show router rsvp status
Description
This command displays RSVP status.
Platforms
All
Output
The following output is an example of RSVP status information.
RSVP Status Output Fields describes RSVP status output fields.
Label |
Description |
---|---|
Admin Status |
Down — RSVP is administratively disabled. Up — RSVP is administratively enabled. |
Oper Status |
Down — RSVP is operationally down. Up — RSVP is operationally up. |
Keep Multiplier |
Displays the keep-multiplier number used by RSVP to declare that a reservation is down or the neighbor is down. |
Refresh Time |
Displays the refresh-time interval (in s), between the successive Path and Resv refresh messages. |
Message Pacing |
Enabled — RSVP messages, specified in the max-burst command, are sent in a configured interval, specified in the period command. Disabled — Message pacing is disabled. RSVP message transmission is not regulated. |
Pacing Period |
Displays the time interval (in ms), when the router can send the specified number of RSVP messages specified in the rsvp max-burst command. |
Max Packet Burst |
Displays the maximum number of RSVP messages that are sent in the specified period under normal operating conditions. |
Soft Preemption Timer |
Displays the time (in s), a node holds on to a reservation for which it has triggered the soft preemption procedure. |
Rapid Retransmit |
Displays the value of the rapid retransmission interval. |
Rapid Retry Limit |
Displays the rapid retry limit. |
Graceful Shutdown |
Specifies whether graceful shutdown of the RSVP node is enabled. |
Dark Bandwidth |
Indicates the status of the dark bandwidth accounting application. |
DBw Sample Intv |
Displays the configured dark bandwidth sampling interval. |
DBw Up Threshold |
Displays the configured dark bandwidth up threshold. |
DBw Down Threshold |
Displays the configured dark bandwidth down threshold. |
DBw Multiplier |
Displays the configured dark bandwidth multiplier. |
DBw Sample Multp |
Displays the configured dark bandwidth sample multiplier. |
B:# show router rsvp status
========================================================================
RSVP Status
========================================================================
Admin Status : Down Oper Status : Down
Keep Multiplier : 3 Refresh Time : 30 sec
Message Pacing : Disabled Pacing Period : 100 msec
Max Packet Burst : 650 msgs Refresh Bypass : Disabled
Rapid Retransmit : 5 hmsec Rapid Retry Limit : 3
Graceful Shutdown : Disabled SoftPreemptionTimer: 300 sec
Implicit Null Label: Disabled Node-id in RRO : Exclude
P2P Merge Point Ab*: 10 P2MP Merge Point A*: 10
DiffServTE AdmModel: Basic
Percent Link Bw CT0: 100 Percent Link Bw CT4: 0
Percent Link Bw CT1: 0 Percent Link Bw CT5: 0
Percent Link Bw CT2: 0 Percent Link Bw CT6: 0
Percent Link Bw CT3: 0 Percent Link Bw CT7: 0
TE0 -> Class Type : 0 Priority : 0
TE1 -> Class Type : 0 Priority : 1
TE2 -> Class Type : 0 Priority : 2
TE3 -> Class Type : 0 Priority : 3
TE4 -> Class Type : 0 Priority : 4
TE5 -> Class Type : 0 Priority : 5
TE6 -> Class Type : 0 Priority : 6
TE7 -> Class Type : 0 Priority : 7
IgpThresholdUpdate : Disabled
Up Thresholds(%) : 0 15 30 45 60 75 80 85 90 95 96 97 98 99 100
Down Thresholds(%) : 100 99 98 97 96 95 90 85 80 75 60 45 30 15 0
Update Timer : N/A
Update on CAC Fail : Disabled
Dark Bandwidth : Enabled DBw Multiplier : 100
DBw Sample Intv : 30 DBw Sample Multp : 3
DBw Up Threshold : 0 %
DBw Down Threshold : 0 %
========================================================================
* indicates that the corresponding row element may have been truncated.
status
Syntax
status
Context
[Tree] (show>router>pcep>pcc status)
Full Context
show router pcep pcc status
Description
This command displays PCEP status information
Platforms
All
Output
The table in the detail parameter (show>router>pcep>pcc detail) describes the status output fields.
Output Example*A:Dut-C>config>router>mpls# show router pcep pcc status
===============================================================================
Path Computation Element Protocol (PCEP) Path Computation Client (PCC) Info
===============================================================================
Admin Status : Up Oper Status : Up
Unknown Msg Limit : 10 msg/min
Keepalive Interval : 30 seconds DeadTimer Interval : 120 seconds
Capabilities List : stateful-delegate stateful-pce segment-rt-path rsvp-
path pce-initiated-lsp
Address : 10.20.1.3
Report Path Constraints: True
Redelegation Interval : 90 seconds
State Interval : 180 seconds State Timer Action : remove
Max SR-TE PCE Init Lsps: 8191
-------------------------------------------------------------------------------
PCEP Path Computation Client (PCC) Peer Info
-------------------------------------------------------------------------------
Peer Admin State/Oper State Oper Keepalive/Oper DeadTimer
-------------------------------------------------------------------------------
10.20.1.24 Up/Up 30/120
-------------------------------------------------------------------------------
===============================================================================
status
Syntax
status
Context
[Tree] (show>router>mpls>forwarding-policies status)
Full Context
show router mpls forwarding-policies status
Description
This command displays MPLS Forwarding status information
Platforms
All
Output
MPLS Forward-policy Status Output Fields describes MPLS forward-policy status output fields.
Label |
Description |
---|---|
Reserved label bl |
Specifies the MPLS reserved label block name. |
*A:Dut-B>show>router>mpls# forwarding-policies status
===============================================================================
Forwarding Policy Status
===============================================================================
Admin Status : Up Oper Status : Down
Reserved label bl: reservedlabel!!!blockname32chars
===============================================================================
status
Syntax
status
Context
[Tree] (show>app-assure>group>cflowd status)
Full Context
show application-assurance group cflowd status
Description
This command displays status information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of status information.
Output ExampleA:ALU-A# show application-assurance group 1 status [isa 1/2] cflowd
========================================================================
Application-Assurance Group Cflowd Status
========================================================================
Cflowd Admin Status : Enabled
Cflowd Oper Status : Enabled
------------------------------------------------------------------------
Volume :
------------------------------------------------------------------------
Sample Rate : <Disabled> or <1 in 500 packets>
Active Flows : 23102
Records Reported : 12345
Records Dropped : 10
Records Per Second : 45
Packets Sent : 1763
Packets Sent Per Sec : 7
------------------------------------------------------------------------
TCP Performance :
------------------------------------------------------------------------
Sample Rate : <Disabled> or <1 in 1000 flows>
Active Flows : 32103
Flows Not Allocated : 33
Records Reported : 12345678
Records Dropped : 100
Records Per Second : 456
Packets Sent : 2057613
Packets Sent Per Sec : 76
========================================================================
A:ALU-A#
A:ALU-A#show application-assurance group <aa-group-id:[partition]> cflowd status
========================================================================
Application-Assurance Group:Partition Cflowd Status
========================================================================
------------------------------------------------------------------------
Volume :
------------------------------------------------------------------------
Admin State : Up
Records Reported : 12345
Records Dropped : 10
------------------------------------------------------------------------
TCP Performance :
------------------------------------------------------------------------
Admin State : Up
Flows Not Allocated : 33
Records Reported : 12345678
Records Dropped : 100
========================================================================
A:ALU-A#
status
Syntax
status [isa mda-id] cflowd
status [isa mda-id]
status [isa mda-id] detail
status [isa mda-id] cpu [sample-period seconds]
status [isa mda-id] overload
status {isa mda-id} qos count
status {isa mda-id} qos pools
Context
[Tree] (show>app-assure>group status)
Full Context
show application-assurance group status
Description
This command displays system statistics.
Parameters
- isa mda-id
-
Displays information about the specified AA ISA.
- cflowd
-
Displays cflowd status information.
- detail
-
Displays detailed status information.
- cpu [sample-period seconds]
-
Displays DPU utilization info about the specified AA ISA. The isa mda-id must be specified. The sample period can be specified within a range of 1 5 seconds (default 1s).
- overload
-
Displays the overload status.
- qos count
-
Displays information about queue statistics. The isa mda-id must be specified.
- qos pools
-
Displays information about AA related pool utilization. The isa mda-id must be specified.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of status information.
Output Example*A:Dut-C# show application-assurance group 1 status
==============================================================================
Application-Assurance Status
==============================================================================
Last time change affecting status : 01/25/2018 18:55:08
Number of Active ISAs : 2
Flows : 0
Flow Resources In Use : 0
AA Subs Created : 0
AA Subs Deleted : 0
AA Subs Modified : 0
AA Subs Quarantined : 0
Seen IP Requests Sent : 0
Seen IP Requests Dropped : 0
-------------------------------------------------------------------------------
Current Average Peak
-------------------------------------------------------------------------------
Active Flows : 0 0 0
Flow Setup Rate (per second) : 0 0 0
Traffic Rate (Mbps) : 0 0 0
Packet Rate (per second) : 0 0 0
AA-Subs Downloaded : 0 0 0
Active Subs : 0 0 0
-------------------------------------------------------------------------------
Packets Octets
-------------------------------------------------------------------------------
Diverted traffic : 0 0
Diverted discards : 0 0
Congestion : 0 0
Errors : 0 N/A
Entered ISA-AAs : 0 0
Buffered in ISA-AAs : 0 0
Discarded in ISA-AAs : 0 0
Policy : 0 0
Congestion : 0 0
Errors : 0 0
Modified in ISA-AAs : 0 0
Packet size increased : 0 0
Packet size decreased : 0 0
Errors (policy bypass) : 0 0
Errors (cut-through) : 0 0
Generated in ISA-AAs : 0 0
HTTP Redirect : 0 0
Exited ISA-AAs : 0 0
Returned discards : 0 0
Congestion : 0 0
Errors : 0 N/A
Returned traffic : 0 0
===============================================================================
*A:Dut-C# show application-assurance group 1 status detail
===============================================================================
Application-Assurance Status
===============================================================================
Last time change affecting status : 01/25/2018 18:55:08
Number of Active ISAs : 2
Flows : 0
Flow Resources In Use : 0
AA Subs Created : 0
AA Subs Deleted : 0
AA Subs Modified : 0
Seen IP Requests Sent : 0
Seen IP Requests Dropped : 0
-------------------------------------------------------------------------------
Current Average Peak
-------------------------------------------------------------------------------
Active Flows : 0 0 0
Flow Setup Rate (per second) : 0 0 0
Traffic Rate (Mbps) : 0 0 0
Packet Rate (per second) : 0 0 0
AA-Subs Downloaded : 0 0 0
Active Subs : 0 0 0
-------------------------------------------------------------------------------
from-sub packets from-sub octets
to-sub packets to-sub octets
-------------------------------------------------------------------------------
Diverted traffic : 0 0
0 0
Diverted discards : 0 0
0 0
Congestion : 0 0
0 0
Errors : 0 N/A
0 N/A
Entered ISA-AAs : 0 0
0 0
Buffered in ISA-AAs : 0 0
0 0
Discarded in ISA-AAs : 0 0
0 0
Policy : 0 0
0 0
Congestion : 0 0
0 0
Errors : 0 0
0 0
Modified in ISA-AAs : 0 0
0 0
Packet size increased : 0 0
0 0
Packet size decreased : 0 0
0 0
Errors (policy bypass) : 0 0
0 0
Errors (cut-through) : 0 0
0 0
Generated in ISA-AAs : 0 0
0 0
HTTP Redirect : 0 0
0 0
Exited ISA-AAs : 0 0
0 0
Returned discards : 0 0
0 0
Congestion : 0 0
0 0
Errors : 0 N/A
0 N/A
Returned traffic : 0 0
0 0
===============================================================================
A:ALU>show>app-assure>group#
===============================================================================
Application-Assurance Status
===============================================================================
Last time change affecting status : 09/28/2012 14:19:05
Number of Active ISAs : 1
Flows : 62
Flow Resources In Use : 0
AA-Subs Created : 200
AA-Subs Deleted : 149
AA-Subs Modified : 3
Seen-IP Requests Sent : 0
Seen-IP Requests Dropped : 0
-------------------------------------------------------------------------------
Current Average Peak
-------------------------------------------------------------------------------
Active Flows : 0 0 16
Flow Setup Rate (per second) : 0 0 1
Traffic Rate (Mbps) : 0 0 0
Packet Rate (per second) : 0 0 6
AA-Subs Downloaded : 51 51 51
Active Subs : 0 0 1
show application-assurance group <aa-group-id> status [isa <slot/mda>] overload
===============================================================================
Application Assurance Group 1 overload
===============================================================================
-------------------------------------------------------------------------------
Trap Configuration High Watermark Low Watermark
-------------------------------------------------------------------------------
Flow usage 95% 90%
Flow setup rate (fps) 60000 55000
Bit rate (Mbps) 9000 8500
Packet rate (pps) 12345678901234567890 12345678901234567890
Datapath CPU usage 95% 90%
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
ISA 4/1 Total up-time (s) : 12345678901234567890
TCA Type
Current Level Average Level Peak Level
State Count Duration (s)
-------------------------------------------------------------------------------
Flow resources
75.1% 50.0% 82.8%
cleared 12345678901234567890 12345678901234567890
Flow setup rate
12345678901234567890 12345678901234567890 12345678901234567890
cleared 0 0
Bit rate
11000 5000 12000
raised 1 123456789
Packet rate
1500000 750000 1600000
cleared 2 12345
Datapath CPU usage
15.1% 10.5% 32.1%
cleared 0 0
Management CPU usage
65.2% 50.0% 77.5%
N/A N/A N/A
-------------------------------------------------------------------------------
Overload Trap Configuration High Watermark Low Watermark
-------------------------------------------------------------------------------
From-sub WA buffer depth 80% 75%
To-sub WA buffer depth 80% 75%
-------------------------------------------------------------------------------
Isa-overload-cut-through : enabled
Overload cut-through TCA
Current from-sub WA : 30%
Current to-sub WA : 40%
State : cleared
Count : 3
Duration (s) : 123
===============================================================================
A:ALU>show>app-assure>group# status isa 3/2 qos count
===============================================================================
Application-assurance Queue Statistics for ISA-AA Group: 1, isa 3/2
===============================================================================
-------------------------------------------------------------------------------
Egress From-Subscriber
Queue 1 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out/Exc Prof forwarded: 28940 3767233
Out/Exc Prof dropped : 0 0
Queue 2 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out/Exc Prof forwarded: 0 0
Out/Exc Prof dropped : 0 0
Egress To-Subscriber
Queue 1 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out/Exc Prof forwarded: 44499 53066848
Out/Exc Prof dropped : 0 0
Queue 2 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out/Exc Prof forwarded: 0 0
Out/Exc Prof dropped : 0 0
Ingress From-Subscriber
Queue 1 Packets Octets
In Profile forwarded : 25548 3361023
In Profile dropped : 0 0
Out/Exc Prof forwarded: 1 60
Out/Exc Prof dropped : 0 0
Queue 2 Packets Octets
In Profile forwarded : 2921 365606
In Profile dropped : 0 0
Out/Exc Prof forwarded: 0 0
Out/Exc Prof dropped : 0 0
Queue 9 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out/Exc Prof forwarded: 0 0
Out/Exc Prof dropped : 0 0
Queue 10 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out/Exc Prof forwarded: 0 0
Out/Exc Prof dropped : 0 0
Ingress To-Subscriber
Queue 1 Packets Octets
In Profile forwarded : 39541 46899769
In Profile dropped : 0 0
Out/Exc Prof forwarded: 1 92
Out/Exc Prof dropped : 0 0
Queue 2 Packets Octets
In Profile forwarded : 5050 6291204
In Profile dropped : 0 0
Out/Exc Prof forwarded: 0 0
Out/Exc Prof dropped : 0 0
Queue 9 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out/Exc Prof forwarded: 0 0
Out/Exc Prof dropped : 0 0
Queue 10 Packets Octets
In Profile forwarded : 0 0
In Profile dropped : 0 0
Out/Exc Prof forwarded: 0 0
Out/Exc Prof dropped : 0 0
===============================================================================
A:ALU>show>app-assure>group#
*A:ALU>show>app-assure>group# status isa 1/2 qos pools
===============================================================================
Pool Information
===============================================================================
FP : 1
Application : Net-Ing Pool Name : default
CLI Config. Resv CBS : Sum
Resv CBS Step : 0% Resv CBS Max : 0%
Amber Alarm Threshold: 0% Red Alarm Threshold : 0%
-------------------------------------------------------------------------------
Utilization State Start-Avg Max-Avg Max-Prob
-------------------------------------------------------------------------------
HiPlus-Slope Down 85% 100% 80%
High-Slope Down 70% 90% 80%
Low-Slope Down 50% 75% 80%
Exceed-Slope Down 30% 55% 80%
Time Avg Factor : 7
Pool Total : 264192 KB
Pool Shared : 129024 KB Pool Resv : 135168 KB
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Current Resv CBS Provisioned Rising Falling Alarm
%age all Queues Alarm Thd Alarm Thd Color
-------------------------------------------------------------------------------
Sum 134640 KB NA NA Green
Pool Total In Use : 0 KB
Pool Shared In Use : 0 KB Pool Resv In Use : 0 KB
WA Shared In Use : 0 KB
HiPlus-Slope Drop Pr*: 0 Hi-Slope Drop Prob : 0
Lo-Slope Drop Prob : 0 Excd-Slope Drop Prob : 0
===============================================================================
Queue Information
===============================================================================
===============================================================================
Queue : 1 Net=be T=1/*
===============================================================================
FC Map : be
Dest Tap : 1/* Dest FP : 1
Admin PIR : 30000000 Oper PIR : Max
Admin CIR : 0 Oper CIR : 0
Admin FIR : 0 Oper FIR : 0
Admin MBS : 132096 KB Oper MBS : 132096 KB
High-Plus Drop T*: 132096 KB High Drop Tail : 132096 KB
Low Drop Tail : 116736 KB Exceed Drop Tail : 119808 KB
CBS : 132 KB Depth : 0
Slope : not-applicable
===============================================================================
...
===============================================================================
Queue : 16 Net=nc T=31/*
===============================================================================
FC Map : nc
Dest Tap : MCast Dest FP : not-applicable
Admin PIR : 30000000 Oper PIR : Max
Admin CIR : 3000000 Oper CIR : 3000000
Admin FIR : 0 Oper FIR : 0
Admin MBS : 66048 KB Oper MBS : 66048 KB
High-Plus Drop T*: 66048 KB High Drop Tail : 66048 KB
Low Drop Tail : 58368 KB Exceed Drop Tail : 59904 KB
CBS : 2640 KB Depth : 0
Slope : not-applicable
No Matching Entries
===============================================================================
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
Pool Information
===============================================================================
Port : 1/2/fm-sub
Application : Net-Egr Pool Name : default
CLI Config. Resv CBS : Sum
Resv CBS Step : 0% Resv CBS Max : 0%
Amber Alarm Threshold: 0% Red Alarm Threshold : 0%
-------------------------------------------------------------------------------
Utilization State Start-Avg Max-Avg Max-Prob
-------------------------------------------------------------------------------
HiPlus-Slope Down 85% 100% 80%
High-Slope Down 70% 90% 80%
Low-Slope Down 50% 75% 80%
Exceed-Slope Down 30% 55% 80%
Time Avg Factor : 7
Pool Total : 116736 KB
Pool Shared : 66048 KB Pool Resv : 50688 KB
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Current Resv CBS Provisioned Rising Falling Alarm
%age all Queues Alarm Thd Alarm Thd Color
-------------------------------------------------------------------------------
Sum 50520 KB NA NA Green
Pool Total In Use : 0 KB
Pool Shared In Use : 0 KB Pool Resv In Use : 0 KB
WA Shared In Use : 0 KB
HiPlus-Slope Drop Pr*: 0 Hi-Slope Drop Prob : 0
Lo-Slope Drop Prob : 0 Excd-Slope Drop Prob : 0
===============================================================================
Queue Information
===============================================================================
===============================================================================
Queue : 1 Net=be Port=1/2/fm-sub
===============================================================================
FC Map : be
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 0 Oper CIR : 0
Admin MBS : 58368 KB Oper MBS : 58368 KB
High-Plus Drop T*: 58368 KB High Drop Tail : 58368 KB
Low Drop Tail : 52224 KB Exceed Drop Tail : 52224 KB
CBS : 1176 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 2 Net=l2 Port=1/2/fm-sub
===============================================================================
FC Map : l2
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 2500000 Oper CIR : 2500000
Admin MBS : 58368 KB Oper MBS : 58368 KB
High-Plus Drop T*: 58368 KB High Drop Tail : 58368 KB
Low Drop Tail : 52224 KB Exceed Drop Tail : 52224 KB
CBS : 3552 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 3 Net=af Port=1/2/fm-sub
===============================================================================
FC Map : af
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 2500000 Oper CIR : 2500000
Admin MBS : 58368 KB Oper MBS : 58368 KB
High-Plus Drop T*: 58368 KB High Drop Tail : 58368 KB
Low Drop Tail : 52224 KB Exceed Drop Tail : 52224 KB
CBS : 11712 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 4 Net=l1 Port=1/2/fm-sub
===============================================================================
FC Map : l1
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 2500000 Oper CIR : 2500000
Admin MBS : 29184 KB Oper MBS : 29184 KB
High-Plus Drop T*: 29184 KB High Drop Tail : 29184 KB
Low Drop Tail : 26112 KB Exceed Drop Tail : 26112 KB
CBS : 3552 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 5 Net=h2 Port=1/2/fm-sub
===============================================================================
FC Map : h2
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 10000000 Oper CIR : Max
Admin MBS : 58368 KB Oper MBS : 58368 KB
High-Plus Drop T*: 58368 KB High Drop Tail : 58368 KB
Low Drop Tail : 52224 KB Exceed Drop Tail : 52224 KB
CBS : 11712 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 6 Net=ef Port=1/2/fm-sub
===============================================================================
FC Map : ef
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 10000000 Oper CIR : Max
Admin MBS : 58368 KB Oper MBS : 58368 KB
High-Plus Drop T*: 58368 KB High Drop Tail : 58368 KB
Low Drop Tail : 52224 KB Exceed Drop Tail : 52224 KB
CBS : 11712 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 7 Net=h1 Port=1/2/fm-sub
===============================================================================
FC Map : h1
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 1000000 Oper CIR : 1000000
Admin MBS : 29184 KB Oper MBS : 29184 KB
High-Plus Drop T*: 29184 KB High Drop Tail : 29184 KB
Low Drop Tail : 26112 KB Exceed Drop Tail : 26112 KB
CBS : 3552 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 8 Net=nc Port=1/2/fm-sub
===============================================================================
FC Map : nc
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 1000000 Oper CIR : 1000000
Admin MBS : 29184 KB Oper MBS : 29184 KB
High-Plus Drop T*: 29184 KB High Drop Tail : 29184 KB
Low Drop Tail : 26112 KB Exceed Drop Tail : 26112 KB
CBS : 3552 KB Depth : 0
Slope : not-applicable
No Matching Entries
===============================================================================
===============================================================================
* indicates that the corresponding row element may have been truncated.
===============================================================================
Pool Information
===============================================================================
Port : 1/2/to-sub
Application : Net-Egr Pool Name : default
CLI Config. Resv CBS : Sum
Resv CBS Step : 0% Resv CBS Max : 0%
Amber Alarm Threshold: 0% Red Alarm Threshold : 0%
-------------------------------------------------------------------------------
Utilization State Start-Avg Max-Avg Max-Prob
-------------------------------------------------------------------------------
HiPlus-Slope Down 85% 100% 80%
High-Slope Down 70% 90% 80%
Low-Slope Down 50% 75% 80%
Exceed-Slope Down 30% 55% 80%
Time Avg Factor : 7
Pool Total : 233472 KB
Pool Shared : 132096 KB Pool Resv : 101376 KB
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Current Resv CBS Provisioned Rising Falling Alarm
%age all Queues Alarm Thd Alarm Thd Color
-------------------------------------------------------------------------------
Sum 101040 KB NA NA Green
Pool Total In Use : 0 KB
Pool Shared In Use : 0 KB Pool Resv In Use : 0 KB
WA Shared In Use : 0 KB
HiPlus-Slope Drop Pr*: 0 Hi-Slope Drop Prob : 0
Lo-Slope Drop Prob : 0 Excd-Slope Drop Prob : 0
===============================================================================
Queue Information
===============================================================================
===============================================================================
Queue : 1 Net=be Port=1/2/to-sub
===============================================================================
FC Map : be
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 0 Oper CIR : 0
Admin MBS : 116736 KB Oper MBS : 116736 KB
High-Plus Drop T*: 116736 KB High Drop Tail : 116736 KB
Low Drop Tail : 104448 KB Exceed Drop Tail : 104448 KB
CBS : 2352 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 2 Net=l2 Port=1/2/to-sub
===============================================================================
FC Map : l2
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 2500000 Oper CIR : 2500000
Admin MBS : 116736 KB Oper MBS : 116736 KB
High-Plus Drop T*: 116736 KB High Drop Tail : 116736 KB
Low Drop Tail : 104448 KB Exceed Drop Tail : 104448 KB
CBS : 7104 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 3 Net=af Port=1/2/to-sub
===============================================================================
FC Map : af
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 2500000 Oper CIR : 2500000
Admin MBS : 116736 KB Oper MBS : 116736 KB
High-Plus Drop T*: 116736 KB High Drop Tail : 116736 KB
Low Drop Tail : 104448 KB Exceed Drop Tail : 104448 KB
CBS : 23424 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 4 Net=l1 Port=1/2/to-sub
===============================================================================
FC Map : l1
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 2500000 Oper CIR : 2500000
Admin MBS : 58368 KB Oper MBS : 58368 KB
High-Plus Drop T*: 58368 KB High Drop Tail : 58368 KB
Low Drop Tail : 52224 KB Exceed Drop Tail : 52224 KB
CBS : 7104 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 5 Net=h2 Port=1/2/to-sub
===============================================================================
FC Map : h2
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 10000000 Oper CIR : Max
Admin MBS : 116736 KB Oper MBS : 116736 KB
High-Plus Drop T*: 116736 KB High Drop Tail : 116736 KB
Low Drop Tail : 104448 KB Exceed Drop Tail : 104448 KB
CBS : 23424 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 6 Net=ef Port=1/2/to-sub
===============================================================================
FC Map : ef
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 10000000 Oper CIR : Max
Admin MBS : 116736 KB Oper MBS : 116736 KB
High-Plus Drop T*: 116736 KB High Drop Tail : 116736 KB
Low Drop Tail : 104448 KB Exceed Drop Tail : 104448 KB
CBS : 23424 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 7 Net=h1 Port=1/2/to-sub
===============================================================================
FC Map : h1
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 1000000 Oper CIR : 1000000
Admin MBS : 58368 KB Oper MBS : 58368 KB
High-Plus Drop T*: 58368 KB High Drop Tail : 58368 KB
Low Drop Tail : 52224 KB Exceed Drop Tail : 52224 KB
CBS : 7104 KB Depth : 0
Slope : not-applicable
===============================================================================
Queue : 8 Net=nc Port=1/2/to-sub
===============================================================================
FC Map : nc
Dest Tap : not-applicable Dest FP : not-applicable
Admin PIR : 10000000 Oper PIR : Max
Admin CIR : 1000000 Oper CIR : 1000000
Admin MBS : 58368 KB Oper MBS : 58368 KB
High-Plus Drop T*: 58368 KB High Drop Tail : 58368 KB
Low Drop Tail : 52224 KB Exceed Drop Tail : 52224 KB
CBS : 7104 KB Depth : 0
Slope : not-applicable
No Matching Entries
===============================================================================
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:ALU>show>app-assure>group#
status
Syntax
status
Context
[Tree] (show>router>mld status)
Full Context
show router mld status
Description
This command displays MLD status information.
If MLD is not enabled, the following message appears:
A:NYC# show router mld status
MINOR: CLI MLD is not configured.
A:NYC#
Platforms
All
Output
The following output is an example of MLD status information MLD Status Fields provides MLD status field descriptions.
Output Example*A:ALA-BA# show router mld status
===============================================================================
MLD Status
===============================================================================
Admin State : Up
Oper State : Up
Query Interval : 125
Last Listener Query Interval : 1
Query Response Interval : 10
Robust Count : 2
===============================================================================
*A:ALA-BA#
Label |
Description |
---|---|
Admin State |
The administrative status of MLD. |
Oper State |
The current operating state of this MLD protocol instance on this router. |
Query Interval |
The frequency at which MLD query packets are transmitted. |
Last Listener Query Interval |
The maximum response time inserted into group-specific queries sent in response to leave group messages, and is also the amount of time between group-specific query messages. |
Query Response Interval |
The maximum query response time advertised in MLDv2 queries. |
Robust Count |
The number of times the router will retry a query. |
status
Syntax
status
Context
[Tree] (show>router>msdp status)
Full Context
show router msdp status
Description
This command displays MSDP status information.
Platforms
All
Output
The following output is an example of MSDP status information. MSDP Status Fields provides MSDP status field descriptions.
Label |
Description |
---|---|
Admin State |
The administrative state. |
Local Address |
The local IP address. |
Active Src Limit |
The active source limit. |
Act Src Lim Excd |
The active source limit which has been exceeded. |
Num. Peers |
The number of peers. |
Num. Peers Estab |
The number of peers established. |
Num. Source Active |
The number of active sources. |
Policies |
The policy to export source active state from the source active list into MSDP. |
Data Encapsulation |
The rendezvous point (RP) using MSDP to encapsulate multicast data received in MSDP register messages inside forwarded MSDP source-active messages - enabled or disabled. |
Rate |
The receive message rate. |
Time |
The receive message time. |
Threshold |
The number of MSDP messages that can be processed before the MSDP message rate limiting function is activated. |
RPF Table |
The name of the reverse path forwarding table. |
Last msdp Enabled |
The time the last MSDP was triggered. |
A:ALA-48# show router msdp status
===============================================================================
MSDP Status
===============================================================================
Admin State : Up
Local Address : None
Global Statistics
Active Src Limit : None
Act Src Lim Excd : 0
Num. Peers : 1
Num. Peers Estab : 1
Num. Source Active : 10
Policies : None
Data Encapsulation : Enabled
Receive Msg Rate
Rate : 0
Time : 0
Threshold : 0
Last Msdp Enabled : 08/30/2002 03:21:43
===============================================================================
A:ALA-48#
status
Syntax
status [detail] [family]
Context
[Tree] (show>router>pim status)
Full Context
show router pim status
Description
This command displays PIM status. The Oper Status reflects the combined operational status of IPv4 or IPv6 PIM protocol status. If both are down, then Oper Status is reflected as down. If IPv4 or IPv6 reflects up, the Oper Status reflects up.
If PIM is not enabled, the following message appears:
A:NYC# show router pim status
MINOR: CLI PIM is not configured.
A:NYC#
Parameters
- detail
-
Displays detailed status information.
- family
-
Displays status information for the specified family.
Platforms
All
Output
The following output is an example of a PIM status configuration. PIM Status Output Fields provides PIM status output field descriptions.
Output ExampleA:dut-d# show router pim status
===============================================================================
PIM Status ipv4
===============================================================================
Admin State : Up
Oper State : Up
IPv4 Admin State : Up
IPv4 Oper State : Up
BSR State : Accept Any
Elected BSR
Address : None
Expiry Time : N/A
Priority : N/A
Hash Mask Length : 30
Up Time : N/A
RPF Intf towards E-BSR : N/A
Candidate BSR
Admin State : Down
Oper State : Down
Address : None
Priority : 0
Hash Mask Length : 30
Candidate RP
Admin State : Down
Oper State : Down
Address : 0.0.0.0
Priority : 192
Holdtime : 150
Auto-RP : Disabled
Multicast-Fast-Failover : Disabled
SSM-Default-Range : Enabled
SSM-Assert-Comp-Mode : Disabled
SSM-Group-Range
None
MC-ECMP-Hashing : Disabled
MC-ECMP-Hashing-Rebalance : Disabled
Enable-MDT-SPT : Disabled
Policy : None
RPF Table : rtable-u
Non-DR-Attract-Traffic : Disabled
Rpf-Vector : None
ESM : Disabled
SSM S,G Scaling (upto 256K) : Enabled (fabric optimization off)
===============================================================================
A:dut-d#
Label |
Description |
---|---|
Admin State |
The administrative status of PIM. |
Oper State |
The current operating state of this PIM protocol instance. |
BSR State |
The state of the router with respect to the Bootstrap mechanism. |
Address |
The address of the elected Bootstrap router. |
Expiry Time |
The time remaining before the router sends the next Bootstrap message. |
Priority |
The priority of the elected Bootstrap router. The higher the value, the higher the priority. |
Hash Mask Length |
The hash mask length of the Bootstrap router. |
Up Time |
The time since the current E-BSR became the Bootstrap router. |
RPF Intf towards |
The RPF interface towards the elected BSR. The value is zero if there is no elected BSR in the network. |
Address |
The address of the candidate BSR OS. |
Expiry Time |
The time remaining before the router sends the next Bootstrap message. |
Auto-RP |
Displays if auto-RP functionality is enabled or disabled. |
Priority |
The priority of the Bootstrap router. The higher the value, the higher the priority. |
Hash Mask Length |
The hash mask length of the candidate Bootstrap router. |
Up Time |
The time since becoming the Bootstrap router. |
Admin State |
The administrative status of CRP. |
Oper State |
The current operating state of the C-RP mechanism. |
Address |
The local RP address. |
Priority |
The CRP's priority for becoming a rendezvous point (RP). A 0 value is the highest priority. |
Holdtime |
The hold time of the candidate RP. It is used by the Bootstrap router to time out the RP entries if it does not listen to another CRP advertisement within the holdtime period. |
Policy |
The PIM policies for a particular PIM instance. |
Default Group |
The default core group address. |
RPF Table |
The route table used for RPF check. |
MC-ECMP-Hashing |
Displays whether hash-based multicast balancing of traffic over ECMP links is enabled or disabled. |
SSM S,G Scaling (up to 256K) |
The status of PIM SSM scaling. |
status
Syntax
status
Context
[Tree] (show>router>p2mp-sr-tree status)
Full Context
show router p2mp-sr-tree status
Description
This command displays P2MP SR tree status information.
Platforms
All
Output
The following output is an example of P2MP SR tree status information.
Output ExampleA:swsim103>show>router>p2mp-sr-tree# status
===============================================================================
P2MP-SR-TREE Status
===============================================================================
Admin Status : Up Oper Status : Up
Reserved Lbl Blk : treeSID
===============================================================================
status
Syntax
status
Context
[Tree] (show>li status)
Full Context
show li status
Description
This command displays LI status information.
Platforms
All
Output
The following output is an example of information about the LI status.
Output Example*A:sim138# show li status
===============================================================================
Lawful Intercept Status Information
===============================================================================
LI Booted Config Status : fail
LI Local Save Allowed : yes
Separate LI administration : no
Last LI Config Save Time : N/A
Last Config Save Result : none
Changes Since Last Save : yes
Last LI Config Modified Time : 2008/01/11 10:24:30
===============================================================================
*A:sim138#
status
Syntax
status
Context
[Tree] (show>cflowd status)
Full Context
show cflowd status
Description
This command displays basic information regarding the administrative and operational status of cflowd.
Platforms
All
Output
The following output is an example of cflowd status information, and Show cflowd Status Fields describes the output fields.
Output Example*A:Dut-C>config>cflowd# /show cflowd status
===============================================================================
Cflowd Status
===============================================================================
Cflowd Admin Status : Enabled
Cflowd Oper Status : Enabled
Cflowd Export Mode : Automatic
Active Flow Timeout : 30 minutes
Inactive Flow Timeout : 10 seconds
Template Retransmit : 600 seconds
Cache Size : 65536 entries
Overflow : 1%
Aggregation Summary : (Not Specified)
VRtr If Index Context: global
Analyze GRE : [Enabled | Disabled]
Analyze L2TPv2 : [Enabled | Disabled]
Analyze IPV4overV6 : [Enabled | Disabled]
Active Flows : 0
Dropped Flows : 0
Total Pkts Rcvd : 2
Total Pkts Dropped : 0
Overflow Events : 0
Raw Flow Counts Aggregate Flow Counts
Flows Created 2 0
Flows Matched 0 0
Flows Flushed 2 0
===============================================================================
Sample Profile Info
===============================================================================
Profile Id Sample Rate
-------------------------------------------------------------------------------
1 1000
===============================================================================
Version Info
===============================================================================
Version Status Sent Open Errors
-------------------------------------------------------------------------------
5 Disabled 0 0 0
8 Disabled 0 0 0
9 Disabled 0 0 0
10 Enabled 1 0 0
===============================================================================
Label |
Description |
---|---|
Cflowd Admin Status |
The desired administrative state for this cflowd remote collector host |
Cflowd Oper Status |
The current operational status of this cflowd remote collector host |
Active Flow Timeout |
The maximum amount of time, in minutes, before an active flow will be exported; if an individual flow is active for this amount of time, the flow is exported and a new flow is created |
Inactive Flow Timeout |
Inactive flow timeout in seconds |
Template Retransmit |
The time in seconds before template definitions are sent |
Cache Size |
The maximum number of active flows to be maintained in the flow cache table |
Overflow |
The percentage number of flows to be flushed when the flow cache size has been exceeded |
Analyze GRE |
Displays whether cflowd analysis of the inner IP packet in a sampled GRE packet that is transiting the local router is enabled or disabled |
Analyze L2TPv2 |
Displays whether cflowd looking for and analyzing the inner IP header of an L2TPv2 frame is enabled or disabled |
Analyze IPV4overV6 |
Displays whether cflowd looking for and analyze the inner IPv4 header of IPv4overIPv6 frames that include MAP-E as well as DS-Lite and SAM traffic is enabled or disabled |
Sample Rate |
The rate at which traffic is sampled and forwarded for cflowd analysis: one (1) — all packets are analyzed 1000 (default) — every 1000th packet is analyzed |
Active Flows |
The current number of active flows being collected |
Total Pkts Rcvd |
The total number of packets sampled and forwarded for cflowd analysis |
Total Pkts Dropped |
The total number of packets dropped |
Aggregation Info: |
|
Type |
The type of data to be aggregated and to the collector |
Status |
enabled — specifies that the aggregation type is enabled |
disabled — specifies that the aggregation type is disabled |
|
Sent |
The number of packets with flow date sent to the associated collector |
Open |
This counter shows the number of partially filled packets which have some flow data but are not yet filled or have been timed out (60 seconds maximum) |
Error |
This counter increments when there was an error during exporting of the collector packet; the most common reason will be a UDP unreachable destination for the configured collector |
Overflow events |
The number of times the active cache overflowed |
Dropped Flows |
Total number of flows dropped due to cache overflow events |
status
Syntax
status
Context
[Tree] (show>router status)
Full Context
show router status
Description
This command displays the router status.
Platforms
All
Output
Router Status Output — The following output is an example of router status information.
There are multiple instances of OSPF. OSPF-0 is persistent. OSPF-1 through OSPF-31 are present when that specific OSPF instance is configured.
Output Example*A:Dut-C# show router status
===============================================================================
Router Status (Router: Base)
===============================================================================
Admin State Oper State
-------------------------------------------------------------------------------
Router Up Up
OSPFv2 Not configured Not configured
RIP Not configured Not configured
RIP-NG Not configured Not configured
ISIS-0 Up Up
MPLS Up Up
RSVP Up Up
LDP Not configured Not configured
BGP Not configured Not configured
IGMP Not configured Not configured
MLD Not configured Not configured
PIM Not configured Not configured
PIMv4 Not configured Not configured
PIMv6 Not configured Not configured
OSPFv3 Not configured Not configured
MSDP Not configured Not configured
BIER Not configured Not configured
Max IPv4 Routes No Limit
Max IPv6 Routes No Limit
Total IPv4 Routes 27
Total IPv6 Routes 27
Max Multicast Routes No Limit
Total IPv4 Mcast Routes PIM not configured
Total IPv6 Mcast Routes PIM not configured
ECMP Max Routes 64
Weighted ECMP Strict
Mcast Info Policy default
Triggered Policies No
Policy reference checks Disabled
LDP Shortcut Disabled
Single SFM Overload Disabled
IP Fast Reroute Disabled
Entropy Label Disabled
ICMP Tunneling Disabled
MSS adjust ISA group Not configured
Reassembly ISA-BB group Not configured
Ipv6 Nbr Reachab. time Not configured 30
IPv6 Nbr stale time (s) 14400
Static Route Hold Down Disabled
TTL Propagate
VPRN Local vc-only
VPRN Transit vc-only
Label Route Local none
Label Route Transit none
LSR Label Route none
LSP BFD Tail Sessions Disabled
Class Forwarding Disabled
Mtrace2 Tests Disabled
Leak Export Disabled
Leak Export Limit 5
===============================================================================
*A:Dut-C#
Router Status Output —The following output is an example of router status information with Mtrace2 enabled.
Output Example===============================================================================
Router Status (Router: Base)
===============================================================================
Admin State Oper State
-------------------------------------------------------------------------------
Router Up Up
OSPFv2 Not configured Not configured
RIP Not configured Not configured
RIP-NG Not configured Not configured
ISIS Not configured Not configured
MPLS Not configured Not configured
RSVP Not configured Not configured
LDP Not configured Not configured
BGP Not configured Not configured
IGMP Not configured Not configured
MLD Not configured Not configured
PIM Not configured Not configured
PIMv4 Not configured Not configured
PIMv6 Not configured Not configured
OSPFv3 Not configured Not configured
MSDP Not configured Not configured
Max IPv4 Routes No Limit
Max IPv6 Routes No Limit
Total IPv4 Routes 0
Total IPv6 Routes 0
Max Multicast Routes No Limit
Total IPv4 Mcast Routes PIM not configured
Total IPv6 Mcast Routes PIM not configured
ECMP Max Routes ECMP not configured
Weighted ECMP Disabled
Mcast Info Policy default
Triggered Policies No
LDP Shortcut Disabled
Single SFM Overload Disabled
IP Fast Reroute Disabled
Entropy Label Disabled
ICMP Tunneling Disabled
MSS adjust ISA group Not configured
Reassembly ISA-BB group Not configured
Ipv6 Nbr Reachab. time Not configured 30
IPv6 Nbr stale time (s) 14400
Static Route Hold Down Disabled
TTL Propagate
VPRN Local vc-only
VPRN Transit vc-only
Label Route Local none
Label Route Transit none
LSR Label Route none
LSP BFD Tail Sessions Disabled
Class Forwarding Disabled
Mtrace2 Tests Enabled on UDP PORT 5001
7450 ESS Router Status Output—The following output is an example of router status information for the 7450 ESS:
Output Example
*A:Performance# configure router ospf [1..31] shutdown
*A:Performance# show router status
================================================================
Router Status (Router: Base)
================================================================
Admin State Oper State
----------------------------------------------------------------
Router Up Up
OSPFv2-0 Up Up
OSPFv2-1 Down Down
OSPFv2-2 Down Down
OSPFv2-3 Down Down
OSPFv2-4 Down Down
OSPFv2-5 Down Down
OSPFv2-6 Down Down
OSPFv2-7 Down Down
OSPFv2-8 Down Down
OSPFv2-9 Down Down
OSPFv2-10 Down Down
OSPFv2-11 Down Down
OSPFv2-12 Down Down
OSPFv2-13 Down Down
OSPFv2-14 Down Down
OSPFv2-15 Down Down
OSPFv2-16 Down Down
OSPFv2-17 Down Down
OSPFv2-18 Down Down
OSPFv2-19 Down Down
OSPFv2-20 Down Down
OSPFv2-21 Down Down
OSPFv2-22 Down Down
OSPFv2-23 Down Down
OSPFv2-24 Down Down
OSPFv2-25 Down Down
OSPFv2-26 Down Down
OSPFv2-27 Down Down
OSPFv2-28 Down Down
OSPFv2-29 Down Down
OSPFv2-30 Down Down
OSPFv2-31 Down Down
RIP Up Up
ISIS Up Up
MPLS Not configured Not configured
RSVP Not configured Not configured
LDP Not configured Not configured
BGP Up Up
IGMP Not configured Not configured
PIM Not configured Not configured
OSPFv3 Not configured Not configured
MSDP Not configured Not configured
Max Routes No Limit
Total IPv4 Routes 244277
Max Multicast Routes No Limit
Total Multicast Routes PIM not configured
ECMP Max Routes 1
Single SFM Overload Enabled hold-off 30 sec
Single SFM State normal
Single SFM Start 004 19:03:39.680
Single SFM Interval 0d 00:16:06
Reassembly ISA-BB group Not configured
Ipv6 Nbr Reachab. time Not configured 30
Triggered Policies No
================================================================
*A:Performance#
Router Status Output for 7750 SR and 7950 XRS—The following output is an example of router status information for the 7750 SR and 7950 XRS:
Output Example*A:Performance# configure router ospf [1..31] shutdown
*A:Performance# show router status
================================================================
Router Status (Router: Base)
================================================================
Admin State Oper State
----------------------------------------------------------------
Router Up Up
OSPFv2-0 Up Up
OSPFv2-1 Down Down
OSPFv2-2 Down Down
OSPFv2-3 Down Down
OSPFv2-4 Down Down
OSPFv2-5 Down Down
OSPFv2-6 Down Down
OSPFv2-7 Down Down
OSPFv2-8 Down Down
OSPFv2-9 Down Down
OSPFv2-10 Down Down
OSPFv2-11 Down Down
OSPFv2-12 Down Down
OSPFv2-13 Down Down
OSPFv2-14 Down Down
OSPFv2-15 Down Down
OSPFv2-16 Down Down
OSPFv2-17 Down Down
OSPFv2-18 Down Down
OSPFv2-19 Down Down
OSPFv2-20 Down Down
OSPFv2-21 Down Down
OSPFv2-22 Down Down
OSPFv2-23 Down Down
OSPFv2-24 Down Down
OSPFv2-25 Down Down
OSPFv2-26 Down Down
OSPFv2-27 Down Down
OSPFv2-28 Down Down
OSPFv2-29 Down Down
OSPFv2-30 Down Down
OSPFv2-31 Down Down
RIP Up Up
ISIS Up Up
MPLS Not configured Not configured
RSVP Not configured Not configured
LDP Not configured Not configured
BGP Up Up
IGMP Not configured Not configured
PIM Not configured Not configured
OSPFv3 Not configured Not configured
MSDP Not configured Not configured
Max Routes No Limit
Total IPv4 Routes 244277
Total IPv6 Routes 0
Max Multicast Routes No Limit
Total Multicast Routes PIM not configured
ECMP Max Routes 1
Single SFM Overload Enabled hold-off 30 sec
Single SFM State normal
Single SFM Start 004 19:03:39.680
Single SFM Interval 0d 00:16:06
Reassembly ISA-BB group Not configured
Ipv6 Nbr Reachab. time Not configured 30
Triggered Policies No
================================================================
*A:Performance#
Class Forwarding—The following output is an example for checking if class-based forwarding is enabled in the global router context.
Output Example*A:Dut-B>show>router# show router "Base" status
===============================================================================
Router Status (Router: Base)
===============================================================================
Admin State Oper State
-------------------------------------------------------------------------------
Router Up Up
OSPFv2 Not configured Not configured
RIP Not configured Not configured
RIP-NG Not configured Not configured
ISIS-0 Up Up
MPLS Up Up
RSVP Up Up
LDP Not configured Not configured
BGP Up Up
IGMP Not configured Not configured
MLD Not configured Not configured
PIM Not configured Not configured
PIMv4 Not configured Not configured
PIMv6 Not configured Not configured
OSPFv3 Not configured Not configured
MSDP Not configured Not configured
Max IPv4 Routes No Limit
Max IPv6 Routes No Limit
Total IPv4 Routes 262
Total IPv6 Routes 262
Max Multicast Routes No Limit
Total IPv4 Mcast Routes PIM not configured
Total IPv6 Mcast Routes PIM not configured
ECMP Max Routes 64
Weighted ECMP Disabled
Mcast Info Policy default
Triggered Policies No
LDP Shortcut Disabled
Single SFM Overload Disabled
IP Fast Reroute Disabled
Entropy Label Disabled
ICMP Tunneling Enabled
MSS adjust ISA group Not configured
Reassembly ISA-BB group Not configured
Ipv6 Nbr Reachab. time Not configured 30
IPv6 Nbr stale time (s) 14400
Static Route Hold Down Disabled
TTL Propagate
VPRN Local vc-only
VPRN Transit vc-only
Label Route Local none
Label Route Transit none
LSR Label Route none
LSP BFD Tail Sessions Disabled
Class Forwarding Enabled
===============================================================================
TTL Propagation and ICMP Tunneling—The following output is an example of TTL propagation and ICMP tunneling configurations, first in base router and then in a VPRN service.
Output Example*A:Performance# show router status
================================================================
Router Status (Router: Base)
================================================================
Admin State Oper State
----------------------------------------------------------------
Router Up Up
OSPFv2-0 Up Up
OSPFv2-2 Down Down
RIP Not configured Not configured
RIP-NG Not configured Not configured
ISIS-0 Up Up
ISIS-1024 Down Down
MPLS Down Down
RSVP Down Down
LDP Up Down
BGP Up Down
IGMP
MLD
PIM
PIMv4
PIMv6
OSPFv3
MSDP
Max IPv4 Routes No Limit
Max IPv6 Routes No Limit
Total IPv4 Routes 0
Total IPv6 Routes 0
Max Multicast Routes No Limit
Total IPv4 Mcast Routes PIM not configured
Total IPv6 Mcast Routes PIM not configured
ECMP Max Routes 1
Mcast Info Policy default
Triggered Policies No
LDP Shortcut Disabled
Single SFM Overload Disabled
IP Fast Reroute Disabled
ICMP Tunneling Disabled
Reassembly ISA-BB group Not configured
ICMP Tunneling Disabled
Ipv6 Nbr Reachab. time Not configured 30
IPv6 Nbr stale time (s) 14400
VPRN Local TTL Propagate vc-only
VPRN Transit TTL Propag* vc-only
Label Route Local TTL P* none
Label Route Transit TTL* none
LSR Label Route TTL Pro* none
===============================================================================
* indicates that the corresponding row element may have been truncated.
*B:bkvm31#
VPRN TTL Propagation and ICMP Tunneling—The following output is an example of TTL propagation and ICMP tunneling configurations in a VPRN service. The TTL propagation has been specified as local and all for VPRN service 5001.
Output Example
*A:Dut-A# configure service vprn 5001 ttl-propagate local all
*A:Dut-A# show router 5001 status
===============================================================================
Router Status (Service: 5001)
===============================================================================
Admin State Oper State
-------------------------------------------------------------------------------
Router Up Up
OSPFv2 Not configured Not configured
RIP Not configured Not configured
RIP-NG Not configured Not configured
ISIS Not configured Not configured
MPLS Not configured Not configured
RSVP Not configured Not configured
LDP Not configured Not configured
BGP Not configured Not configured
IGMP Not configured Not configured
MLD Not configured Not configured
PIM Not configured Not configured
PIMv4 Not configured Not configured
PIMv6 Not configured Not configured
OSPFv3 Not configured Not configured
MSDP Not configured Not configured
Max IPv4 Routes No Limit
Max IPv6 Routes No Limit
Total IPv4 Routes 2
Total IPv6 Routes 2
Max Multicast Routes No Limit
Total IPv4 Mcast Routes PIM not configured
Total IPv6 Mcast Routes PIM not configured
ECMP Max Routes 1
Mcast Info Policy default
Triggered Policies No
GRT Lookup Disabled
Local Management Disabled
Single SFM Overload Disabled
IP Fast Reroute Disabled
ICMP Tunneling Disabled
Reassembly ISA-BB group Not configured
ICMP Tunneling Disabled
Ipv6 Nbr Reachab. time Not configured 30
VPRN Local TTL Propagate all
VPRN Transit TTL Propag* inherit (vc-only)
===============================================================================
* indicates that the corresponding row element may have been truncated.
*A:Dut-A#
status
Syntax
status
Context
[Tree] (show>router>rib-api status)
Full Context
show router rib-api status
Description
This command displays RIB-API status information.
Platforms
All
Output
The following output is an example of RIB-API status information.
Output Example*A:Dut-A# /show router rib-api status
===============================================================================
Rib-Api Status
===============================================================================
MPLS Admin Reserved Label Block Name
Status
-------------------------------------------------------------------------------
Up ribapi
===============================================================================
status
Syntax
status
Context
[Tree] (clear>application-assurance>group status)
Full Context
clear application-assurance group status
Description
This command clears application assurance system statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
status
Syntax
status
Context
[Tree] (show>router>isis status)
Full Context
show router isis status
Description
This command displays information regarding IS-IS status.
Platforms
All
Output
The following output is an example of the IS-IS status, and IS-IS status output fields describes the output fields.
show router isis status
Output Example
===============================================================================
Rtr Base ISIS Instance 0 Status
===============================================================================
ISIS Cfg System Id : 0000.0000.0000
ISIS Oper System Id : 0100.2000.1001
ISIS Cfg Router Id : 0.0.0.0
ISIS Oper Router Id : 10.20.1.1
ISIS Cfg IPv6 Router Id : ::
ISIS Oper IPv6 Router Id : ::
ASN : 0
Admin State : Up
Oper State : Up
Ipv4 Routing : Enabled
Ipv6 Routing : Disabled
Mcast Ipv4 Routing : Enabled, Native
Mcast Ipv6 Routing : Disabled
Last Enabled : 12/09/2022 18:43:43
Level Capability : L1L2
Authentication Check : True
Auth Keychain : Disabled
Authentication Type : None
CSNP-Authentication : Enabled
HELLO-Authentication : Enabled
PSNP-Authentication : Enabled
Traffic Engineering : Disabled
Oper IPv6 TE Router Id : ::
Graceful Restart : Disabled
GR Helper Mode : Disabled
Overload-On-Boot Timeout : 0
Overload Max-Metric : False
Overload-On-Boot Max-Metric : False
Ovl Export Interlevel : Disabled
Ovl Export External : Disabled
Ovl FIB Error Notify Only : Disabled
Ovl FIB Error Retry : N.A.
LSP Lifetime : 1200
LSP Min Remaining Lifetime : N.A.
LSP Refresh Half Interval : 600 (Config) 600 (Oper)
LSP Wait (ms) : 5000 (Max) 10 (Initial) 1000 (Second)
LSP MTU Size : 1492 (Config)
L1 LSP MTU Size : 1492 (Config) 1492 (Oper)
L2 LSP MTU Size : 1492 (Config) 1492 (Oper)
L1 MAX LSP MTU Size : 9187
L2 MAX LSP MTU Size : 1497
Adjacency Check : loose
L1 Auth Keychain : Disabled
L1 Auth Type : none
L1 CSNP-Authentication : Enabled
L1 HELLO-Authentication : Enabled
L1 PSNP-Authentication : Enabled
L1 Preference : 15
L1 Ext. Preference : 160
L1 Wide Metrics : Disabled
L1 LSDB Overload : Disabled
L1 LSPs : 1
L1 Default Metric : 10
L1 IPv6 Def Metric : 10
L1 Mcast IPv4 Def Metric : 10
L1 Mcast IPv6 Def Metric : 10
L1 Adv Router Cap : Enabled
L1 Bier Template : None, Disabled
L1 Total Exp Routes : 0
All-L1-MacAddr (Cfg) : 01:80:c2:00:00:14
Last SPF : 12/09/2022 18:43:43
SPF Wait (ms) : 10000 (Max) 1000 (Initial) 1000 (Second)
Multi-topology : Disabled
IPv6-Unicast MT2 : Disabled
IPv4-Multicast MT3 : Disabled
IPv6-Multicast MT4 : Disabled
Area Addresses : 30.31
Standard Multi-Instance : Disabled
IID TLV : Disabled
Prefix Attributes TLV : Disabled
L2 Auth Keychain : Disabled
L2 Auth Type : none
L2 CSNP-Authentication : Enabled
L2 HELLO-Authentication : Enabled
L2 PSNP-Authentication : Enabled
L2 Preference : 18
L2 Ext. Preference : 165
L2 Wide Metrics : Enabled
L2 LSDB Overload : Disabled
L2 LSPs : 6
L2 Default Metric : 10
L2 IPv6 Def Metric : 10
L2 Mcast IPv4 Def Metric : 10
L2 Mcast IPv6 Def Metric : 10
L2 Adv Router Cap : Enabled
L2 Bier Template : None, Disabled
L2 Total Exp Routes : 0
All-L2-MacAddr (Cfg) : 01:80:c2:00:00:15
Export Policies : None
Import Policies : None
LFA Policies : None
Multicast Import : None
Advertise-Passive-Only : Disabled
Ignore Attached Bit : Disabled
Suppress Attached Bit : Disabled
Default Route Tag : None
Rib Prio List High : None
Rib Prio Tag High : None
Ldp Sync Admin State : Up
LDP-over-RSVP : Disabled
IGP-Shortcut : Disabled
IGP SC Allow SR over SR-TE : Disabled
IPv4 IGP SC Tunn-Nhop : Res-Disabled
IPv6 IGP SC Tunn-Nhop : Res-Disabled
SRv4 IGP SC Tunn-Nhop : Res-Disabled
SRv6 IGP SC Tunn-Nhop : Res-Disabled
Advertise-Tunnel-Link : Disabled
Export Limit : 0
Exp Lmt Log Percent : 0
Loopfree-Alternate : Disabled
Remote-LFA : Disabled
Max PQ Cost : 4261412864
Remote-LFA (node-protect) : Disabled
Max PQ nodes (node-protect) : 16
Augment-route-table : Disabled
TI-LFA : Disabled
Max SR FRR Labels : 2
TI-LFA (node-protect) : Disabled
L1 LFA : Included
L2 LFA : Included
Advertise Router Cap : Disabled
Hello Padding : Disabled
L1 Hello Padding : Disabled
L2 Hello Padding : Disabled
Ignore Lsp Errors : Disabled
Ignore Narrow Metric : Disabled
Reference Bandwidth : 0
Ucast Import Disable : None
Segment Routing : Disabled
Flex Algo : Down
Mapping Server : Disabled
Purge Originator Id : Disabled
Class Based Forwarding : Disabled
Entropy Label : Enabled
Override ELC : Enabled
Micro loop avoidance : Disabled fib-delay 15
===============================================================================
The following output is an example of the LFA policies configured in the configure router isis, and IS-IS status output fields describes the output fields.
show router isis status
Output Example
===============================================================================
Rtr Base ISIS Instance 0 Status
===============================================================================
ISIS Cfg System Id : 0000.C0A8.0001
ISIS Oper System Id : 0100.C0A8.1001
ISIS Cfg Router Id : 0.0.0.0
ISIS Oper Router Id : 10.20.1.3
ISIS Cfg IPv6 Router Id : ::
ISIS Oper IPv6 Router Id : ::
ASN : 0
Admin State : Up
Oper State : Up
Ipv4 Routing : Enabled
Ipv6 Routing : Disabled
Mcast Ipv4 Routing : Enabled, Native
Mcast Ipv6 Routing : Disabled
Last Enabled : 12/09/2022 18:43:43
Level Capability : L1
Authentication Check : True
Auth Keychain : Disabled
Authentication Type : None
CSNP-Authentication : Enabled
HELLO-Authentication : Enabled
PSNP-Authentication : Enabled
Traffic Engineering : Disabled
Oper IPv6 TE Router Id : ::
Graceful Restart : Disabled
GR Helper Mode : Disabled
Overload-On-Boot Timeout : 0
Overload Max-Metric : False
Overload-On-Boot Max-Metric : False
Ovl Export Interlevel : Disabled
Ovl Export External : Disabled
Ovl FIB Error Notify Only : Disabled
Ovl FIB Error Retry : N.A.
LSP Lifetime : 1200
LSP Min Remaining Lifetime : N.A.
LSP Refresh Half Interval : 600 (Config) 600 (Oper)
LSP Wait (ms) : 5 (Max) 0 (Initial) 1 (Second)
LSP MTU Size : 1492 (Config)
L1 LSP MTU Size : 1492 (Config) 1492 (Oper)
L2 LSP MTU Size : 1492 (Config) 1492 (Oper)
L1 MAX LSP MTU Size : 9187
L2 MAX LSP MTU Size : 1497
Adjacency Check : loose
L1 Auth Keychain : Disabled
L1 Auth Type : none
L1 CSNP-Authentication : Enabled
L1 HELLO-Authentication : Enabled
L1 PSNP-Authentication : Enabled
L1 Preference : 15
L1 Ext. Preference : 160
L1 Wide Metrics : Enabled
L1 LSDB Overload : Disabled
L1 LSPs : 51
L1 Default Metric : 10
L1 IPv6 Def Metric : 10
L1 Mcast IPv4 Def Metric : 10
L1 Mcast IPv6 Def Metric : 10
L1 Adv Router Cap : Enabled
L1 Bier Template : None, Disabled
L1 Total Exp Routes : 1
All-L1-MacAddr (Cfg) : 01:80:c2:00:00:14
Last SPF : 12/09/2022 18:43:43
SPF Wait (ms) : 10 sec (Max) 1000 ms (Initial) 1000 ms (Second)
Multi-topology : Disabled
IPv6-Unicast MT2 : Disabled
IPv4-Multicast MT3 : Disabled
IPv6-Multicast MT4 : Disabled
Area Addresses : 49.0001
Standard Multi-Instance : Disabled
IID TLV : Disabled
Prefix Attributes TLV : Disabled
L2 Auth Keychain : Disabled
L2 Auth Type : none
L2 CSNP-Authentication : Enabled
L2 HELLO-Authentication : Enabled
L2 PSNP-Authentication : Enabled
L2 Preference : 18
L2 Ext. Preference : 165
L2 Wide Metrics : Disabled
L2 LSDB Overload : Disabled
L2 LSPs : 0
L2 Default Metric : 10
L2 IPv6 Def Metric : 10
L2 Mcast IPv4 Def Metric : 10
L2 Mcast IPv6 Def Metric : 10
L2 Adv Router Cap : Enabled
L2 Bier Template : None, Disabled
L2 Total Exp Routes : 0
All-L2-MacAddr (Cfg) : 01:80:c2:00:00:15
Export Policies : static
Import Policies : None
LFA Policies : pol1
: pol2
: pol3
: pol4
: pol5
Multicast Import : None
Advertise-Passive-Only : Disabled
Ignore Attached Bit : Disabled
Suppress Attached Bit : Disabled
Default Route Tag : None
Rib Prio List High : None
Rib Prio Tag High : None
Ldp Sync Admin State : Up
LDP-over-RSVP : Disabled
IGP-Shortcut : Disabled
IGP SC Allow SR over SR-TE : Disabled
IPv4 IGP SC Tunn-Nhop : Res-Disabled
IPv6 IGP SC Tunn-Nhop : Res-Disabled
SRv4 IGP SC Tunn-Nhop : Res-Disabled
SRv6 IGP SC Tunn-Nhop : Res-Disabled
Advertise-Tunnel-Link : Disabled
Export Limit : 0
Exp Lmt Log Percent : 0
Loopfree-Alternate : Enabled
Remote-LFA : Disabled
Max PQ Cost : 4261412864
Remote-LFA (node-protect) : Disabled
Max PQ nodes (node-protect) : 16
Augment-route-table : Disabled
TI-LFA : Disabled
Max SR FRR Labels : 2
TI-LFA (node-protect) : Disabled
L1 LFA : Included
L2 LFA : Included
Advertise Router Cap : Disabled
Hello Padding : Disabled
L1 Hello Padding : Disabled
L2 Hello Padding : Disabled
Ignore Lsp Errors : Disabled
Ignore Narrow Metric : Disabled
Reference Bandwidth : 0
Ucast Import Disable : None
Segment Routing : Disabled
Flex Algo : Down
Mapping Server : Disabled
Purge Originator Id : Disabled
Class Based Forwarding : Disabled
Entropy Label : Enabled
Override ELC : Enabled
Micro loop avoidance : Disabled fib-delay 15
===============================================================================
The following output is an example of the detailed LFA policies configured in the configure router isis context.
show router isis interface "DUTC_TO_DUTE.1.0" detail
Output Example
===============================================================================
Rtr Base ISIS Instance 0 Interfaces (detail)
===============================================================================
-------------------------------------------------------------------------------
Interface : DUTC_TO_DUTE.1.0 Level Capability: L1L2
Oper State : Up Admin State : Up
Auth Keychain : Disabled
Auth Type : None Auth State : Enabled
Circuit Id : 3 Retransmit Int. : 5
Type : Broadcast LSP Pacing Int. : 100
Oper Type : Broadcast CSNP Int. : 10
Mesh Group : Inactive BER : none
LFA NH Template : "template1" Bfd Enabled : No
Topology : IPv4-Unicast, IPv6-Unicast, IPv4-Multicast, IPv6-Multicast
Te Metric : 0 Te State : Down
Admin Groups : None
Ldp Sync : outOfService Ldp Sync Wait : Disabled
Ldp Timer State : Disabled Ldp Tm Left : 0
Route Tag : None LFA : Included
Level : 1 Adjacencies : 0
Desg. IS : Dut-C
Auth Keychain : Disabled
Auth Type : None Metric : 10
Hello Timer : 9 IPv6-Ucast-Met : 10
Priority : 64 IPv6-Mcast-Met : 10
Passive : No IPv4-Mcast-Met : 10
SD-Offset : 0 SF-Offset : 0
Hello Mult. : 3
Level : 2 Adjacencies : 0
Desg. IS : Dut-C
Auth Keychain : Disabled
Auth Type : None Metric : 10
Hello Timer : 9 IPv6-Ucast-Met : 10
Priority : 64 IPv6-Mcast-Met : 10
Passive : No IPv4-Mcast-Met : 10
SD-Offset : 0 SF-Offset : 0
Hello Mult. : 3
===============================================================================
The following output is an example of the output with flexible algorithms enabled, and IS-IS status output fields describes the output fields.
show router isis 0 status
Output Example
===============================================================================
Rtr Base ISIS Instance 0 Status
===============================================================================
ISIS Cfg System Id : 4900.0000.0001
ISIS Oper System Id : 4900.0000.0001
ISIS Cfg Router Id : 10.20.1.1
ISIS Oper Router Id : 10.20.1.1
ISIS Cfg IPv6 Router Id : ::
ISIS Oper IPv6 Router Id : ::
ASN : 0
Admin State : Up
Oper State : Up
Ipv4 Routing : Enabled
Ipv6 Routing : Disabled
Mcast Ipv4 Routing : Enabled, Native
Mcast Ipv6 Routing : Disabled
Last Enabled : 05/28/2020 13:17:48
Level Capability : L1L2
Authentication Check : True
Auth Keychain : MyKeyChain
Authentication Type : None
CSNP-Authentication : Enabled
HELLO-Authentication : Enabled
PSNP-Authentication : Enabled
Traffic Engineering : Disabled
Oper IPv6 TE Router Id : ::
Graceful Restart : Disabled
GR Helper Mode : Disabled
Overload-On-Boot Timeout : 0
Overload Max-Metric : False
Overload-On-Boot Max-Metric : False
Ovl Export Interlevel : Disabled
Ovl Export External : Disabled
Ovl FIB Error Notify Only : Disabled
Ovl FIB Error Retry : N.A.
LSP Lifetime : 1200
LSP Min Remaining Lifetime : N.A.
LSP Refresh Half Interval : 600 (Config) 600 (Oper)
LSP Wait (ms) : 5000 (Max) 10 (Initial) 1000 (Second)
LSP MTU Size : 1492 (Config)
L1 LSP MTU Size : 1492 (Config) 1492 (Oper)
L2 LSP MTU Size : 1492 (Config) 1492 (Oper)
L1 MAX LSP MTU Size : 9775
L2 MAX LSP MTU Size : 1561
Adjacency Check : loose
L1 Auth Keychain : Disabled
L1 Auth Type : none
L1 CSNP-Authentication : Enabled
L1 HELLO-Authentication : Enabled
L1 PSNP-Authentication : Enabled
L1 Preference : 15
L1 Ext. Preference : 160
L1 Wide Metrics : Enabled
L1 LSDB Overload : Disabled
L1 LSPs : 1
L1 Default Metric : 10
L1 IPv6 Def Metric : 10
L1 Mcast IPv4 Def Metric : 10
L1 Mcast IPv6 Def Metric : 10
L1 Adv Router Cap : Enabled
L1 Bier Template : None, Disabled
L1 Total Exp Routes : 0
All-L1-MacAddr (Cfg) : 01:80:c2:00:00:14
Last SPF : 06/03/2020 10:27:06
SPF Wait (ms) : 10000 (Max) 1000 (Initial) 1000 (Second)
Multi-topology : Disabled
IPv6-Unicast MT2 : Disabled
IPv4-Multicast MT3 : Disabled
IPv6-Multicast MT4 : Disabled
Area Addresses : 49.0001
Standard Multi-Instance : Disabled
IID TLV : Disabled
Prefix Attributes TLV : Disabled
L2 Auth Keychain : Disabled
L2 Auth Type : none
L2 CSNP-Authentication : Enabled
L2 HELLO-Authentication : Enabled
L2 PSNP-Authentication : Enabled
L2 Preference : 18
L2 Ext. Preference : 165
L2 Wide Metrics : Enabled
L2 LSDB Overload : Disabled
L2 LSPs : 3
L2 Default Metric : 10
L2 IPv6 Def Metric : 10
L2 Mcast IPv4 Def Metric : 10
L2 Mcast IPv6 Def Metric : 10
L2 Adv Router Cap : Enabled
L2 Bier Template : None, Disabled
L2 Total Exp Routes : 0
All-L2-MacAddr (Cfg) : 01:80:c2:00:00:15
Export Policies : None
Import Policies : None
LFA Policies : None
Multicast Import : None
Advertise-Passive-Only : Disabled
Ignore Attached Bit : Disabled
Suppress Attached Bit : Disabled
Default Route Tag : None
Rib Prio List High : None
Rib Prio Tag High : None
Ldp Sync Admin State : Up
LDP-over-RSVP : Disabled
IGP-Shortcut : Disabled
IPv4 IGP SC Tunn-Nhop : Res-Disabled
IPv6 IGP SC Tunn-Nhop : Res-Disabled
SRv4 IGP SC Tunn-Nhop : Res-Disabled
SRv6 IGP SC Tunn-Nhop : Res-Disabled
Advertise-Tunnel-Link : Disabled
Export Limit : 0
Exp Lmt Log Percent : 0
Loopfree-Alternate : Disabled
Remote-LFA : Disabled
Max PQ Cost : 4261412864
Remote-LFA (node-protect) : Disabled
Max PQ nodes (node-protect) : 16
Augment-route-table : Disabled
TI-LFA : Disabled
Max SR FRR Labels : 2
TI-LFA (node-protect) : Disabled
L1 LFA : Included
L2 LFA : Included
Advertise Router Cap : Area
Hello Padding : Disabled
L1 Hello Padding : Disabled
L2 Hello Padding : Disabled
Ignore Lsp Errors : Disabled
Ignore Narrow Metric : Disabled
Reference Bandwidth : 0
Ucast Import Disable : None
Segment Routing : Up
Flex Algo : Up
Mapping Server : Down
Purge Originator Id : Disabled
Class Based Forwarding : Disabled
Entropy Label : Enabled
Override ELC : Disabled
Micro loop avoidance : Disabled fib-delay 15
===============================================================================
Label |
Description |
---|---|
ISIS Cfg System Id |
Configured IS-IS system ID |
ISIS Oper System Id |
Operational IS-IS system ID |
ISIS Cfg Router Id |
Configured IS-IS router ID |
ISIS Oper Router Id |
Operational IS-IS router ID |
ISIS Cfg IPv6 Router Id |
Configured IS-IS IPv6 router ID |
ISIS Oper IPv6 Router Id |
Operational IS-IS IPv6 router ID |
ASN |
The Autonomous System Number (ASN) the IGP uses when the IS-IS Traffic Engineering Database (TEDB) export is enabled. The ASN value represents either the ASN from the confederation AS, or the router AS if confederations are not configured. |
Admin State Oper State |
Up — IS-IS is administratively up |
Down — IS-IS is administratively down |
|
Ipv4 Routing |
Enabled — IPv4 routing is enabled Disabled — IPv4 routing is disabled |
Ipv6 Routing |
Disabled — IPv6 routing is disabled Enabled, Native — IPv6 routing is enabled Enabled, Multi-topology — Multi-topology TLVs for IPv6 routing is enabled |
Mcast Ipv4 Routing |
Enabled — Multicast is enabled Disabled — Multicast is disabled Native — Multicast in IS-IS MT0 is enabled Multi-topology — Multicast in IS-IS MT3 (IPv4) is enabled |
Mcast Ipv6 Routing |
Enabled — Multicast is enabled Disabled — Multicast is disabled Native — Multicast in IS-IS MT0 is enabled Multi-topology — Multicast in IS-IS MT4 (IPv6) is enabled |
Last Enabled |
Date and time when IS-IS was last enabled in the router |
Level Capability |
Routing level for the IS-IS routing process |
Authentication Check |
True — All IS-IS mismatched protocol packets are rejected False — Authentication is performed on received IS-IS protocol packets but mismatched packets are not rejected |
Auth Keychain |
Authentication keychain name used by IS-IS for the session when enabled |
Authentication Type |
Authentication method used to verify the authenticity of packets sent by neighboring routers on an IS-IS interface |
CSNP-Authentication |
Enabled — Complete Sequence Number Packet (CSNP) authentication is enabled Disabled — CSNP authentication is disabled |
HELLO-Authentication |
Enabled — Hello packet authentication is enabled Disabled — Hello packet authentication is disabled |
PSNP-Authentication |
Enabled — Partial Sequence Number Packet (PSNP) authentication is enabled Disabled — PSNP authentication is disabled |
Traffic Engineering |
Enabled — TE is enabled for the router Disabled — TE is disabled so that TE metrics are not generated and are ignored when received by this node |
Oper IPv6 TE Router Id |
This value provides the IS-IS IPv6 TE Router ID TLV (TLV 140) defined by RFC 6119. The IPv6 TE Router ID is configured using the configure router ipv6-te-router-id interface name command. By default, the system IPv6 address is used when IPv6 TE is enabled. |
Graceful Restart |
Enabled — Graceful restart is enabled for this instance of IS-IS on the router Disabled — Graceful restart capability is disabled for this instance of IS-IS on the router |
LFA Policies |
Indicates the configured LFA policies |
Overload-On-Boot Timeout | Indicates if the overload-on-boot timeout is configured |
Overload-On-Boot Max-Metric | Indicates if the overload-on-boot maximum metric is configured |
Ovl Export Interlevel | Indicates if overload export interlevel is configured |
Ovl Export External | Indicates if overload export external is configured |
Ovl FIB Error Notify Only | Indicates if overload notification only is configured.
Disabled — Indicates the router will go into overload mode when the overload condition is reached. Enabled — Indicates the router will not go into overload mode when the overload condition is reached and instead will only advertise a notification. |
Ovl FIB Error Retry | Indicates the amount of time in seconds until the router periodically retries to program the FIB during the gracious overload condition |
Ldp Sync Admin State |
Indicates if the IGP-LDP synchronization feature is enabled on all interfaces participating in the OSPF routing protocol |
Loopfree-Alternate |
Indicates if Loop-Free Alternate (LFA) is enabled in this IS-IS instance |
LFA NH Template |
Indicates the LFA Next-Hop (NH) template is applied for the configured LFA policies |
status
Syntax
status
Context
[Tree] (show>router>ospf3 status)
[Tree] (show>router>ospf status)
Full Context
show router ospf3 status
show router ospf status
Description
Displays the general status of OSPF.
Platforms
All
Output
OSPF Status Output Fields
OSPF Status Output Fields describes the command output fields for OSPF status.
Label |
Description |
---|---|
OSPF Router Id |
A 32-bit integer uniquely identifying the router in the Autonomous System. The SR OS system defaults to the System IP address or if not configured the 32 least significant bits of the system MAC address. |
OSPF Version |
The current version number of the OSPF protocol is 2. |
OSPF Admin Status |
Disabled — Denotes that the OSPF process is disabled on all interfaces. Enabled — Denotes that the OSPF process is active on at least one interface. |
OSPF Oper Status |
Disabled — Denotes that the OSPF process is not operational on all interfaces. Enabled — Denotes that the OSPF process is operational on at least one interface. |
Preference |
The route preference for OSPF internal routes. |
External Preference |
The route preference for OSPF external routes. |
Backbone Router |
False — This variable indicates that this router is not configured as an OSPF back bone router. True — This variable indicates that this router is configured as an OSPF back bone router. |
Area Border Router |
False — This router is not an area border router. True — This router is an area border router. |
AS Border Router |
False — This router is not configured as an Autonomous System border router. True — This router is configured as an Autonomous System border router. |
OSPF Ldp Sync Admin Status |
Indicates whether the IGP-LDP synchronization feature is enabled or disabled on all interfaces participating in the OSPF routing protocol. |
*A:Dut-A>config>service# show router ospf status
===============================================================================
Rtr Base OSPFv2 Instance 0 Status
===============================================================================
OSPF Cfg Router Id : 0.0.0.0
OSPF Oper Router Id : 10.20.1.1
OSPF Version : 2
OSPF Admin Status : Enabled
OSPF Oper Status : Enabled
Graceful Restart : Disabled
GR Helper Mode : Disabled
GR Strict LSA Checking : Enabled
Preference : 10
External Preference : 150
Backbone Router : True
Area Border Router : False
AS Border Router : False
Opaque LSA Support : True
Traffic Engineering Support : True
RFC 1583 Compatible : True
Demand Exts Support : False
In Overload State : False
In External Overflow State : False
Exit Overflow Interval : 0
Last Overflow Entered : Never
Last Overflow Exit : Never
External LSA Limit : -1
Reference Bandwidth : 100,000,000 Kbps
Init SPF Delay : 1000 msec
Sec SPF Delay : 1000 msec
Max SPF Delay : 1000 msec
Min LS Arrival Interval : 1000 msec
Init LSA Gen Delay : 5000 msec
Sec LSA Gen Delay : 5000 msec
Max LSA Gen Delay : 5000 msec
Lsa accumulate : 1000 msec
Redistribute delay : 1000 msec
Incremental SPF wait : 1000 msec
Last Ext SPF Run : Never
Ext LSA Cksum Sum : 0x0
OSPF Last Enabled : 07/06/2017 18:51:52
Unicast Import : True
Multicast Import : False
Export Policies : None
Import Policies : None
Lfa Policies : None
OSPF Ldp Sync Admin Status : Enabled
LDP-over-RSVP : Disabled
IGP-Shortcut : Disabled
IPv4 IGP SC Tunn-Nhop : Res-Disabled
Advertise-Tunnel-Link : Disabled
LFA : Disabled
Remote-LFA : Disabled
Max PQ Cost : 65535
TI-LFA : Disabled
Max SR FRR Labels : 2
Export Limit : 0
Export Limit Log Percent : 0
Total Exp Routes : 0
RIB-priority-high prefix list: None
Segment Routing : Enabled
Database export : Disabled
ASN : n/a
Entropy Label : Enabled
Override ELC : Enabled
===============================================================================
*A:Dut-C>config>router>ospf3# show router ospf3 0 status
===============================================================================
Rtr Base OSPFv3 Instance 0 Status
===============================================================================
OSPF Cfg Router Id : 10.20.1.3
OSPF Oper Router Id : 10.20.1.3
OSPF Version : 3
OSPF Admin Status : Enabled
OSPF Oper Status : Enabled
Graceful Restart : Disabled
GR Helper Mode : Disabled
GR Strict LSA Checking : Enabled (operational down)
Preference : 10
External Preference : 150
Backbone Router : False
Area Border Router : False
AS Border Router : True
Traffic Engineering Support : False
Demand Exts Support : False
In Overload State : False
In External Overflow State : False
Exit Overflow Interval : 0
Last Overflow Entered : Never
Last Overflow Exit : Never
External LSA Limit : -1
Reference Bandwidth : 100,000,000 Kbps
Init SPF Delay : 1000 msec
Sec SPF Delay : 1000 msec
Max SPF Delay : 10000 msec
Min LS Arrival Interval : 1000 msec
Init LSA Gen Delay : 5000 msec
Sec LSA Gen Delay : 5000 msec
Max LSA Gen Delay : 5000 msec
Lsa accumulate : 1000 msec
Redistribute delay : 1000 msec
Incremental SPF wait : 1000 msec
Last Ext SPF Run : 10/11/2018 07:39:48
Ext LSA Cksum Sum : 0x10926
OSPF Last Enabled : 10/11/2018 07:39:45
Unicast Import : True
Multicast Import : False
Export Policies : static
Import Policies : None
Lfa Policies : None
OSPF Ldp Sync Admin Status : Enabled
LDP-over-RSVP : Disabled
IGP-Shortcut : Disabled
IPv6 IGP SC Tunn-Nhop : Res-Disabled
Advertise-Tunnel-Link : Disabled
LFA : Enabled
Remote-LFA : Enabled
Max PQ Cost : 65535
TI-LFA : Disabled
Max SR FRR Labels : 2
Export Limit : 0
Export Limit Log Percent : 0
Total Exp Routes : 1
RIB-priority-high prefix list: None
Segment Routing : Enabled
Extended LSA : sparse
===============================================================================
status
Syntax
status
Context
[Tree] (show>router>isis>srv6 status)
Full Context
show router isis segment-routing-v6 status
Description
This command displays the IS-IS SRv6 status.
Platforms
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
status
Syntax
status
Context
[Tree] (show>subscr-mgmt status)
Full Context
show subscriber-mgmt status
Description
Commands in this context display subscriber management status information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
status
Syntax
status
Context
[Tree] (show>app-assure>group>aa-sub>um status)
Full Context
show application-assurance group aa-sub usage-monitor status
Description
This command displays the usage monitor status.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
status
Syntax
status
Context
[Tree] (show>router>bier status)
Full Context
show router bier status
Description
This command displays the BIER status.
Platforms
All
steering-profile
steering-profile
Syntax
steering-profile steering-profile-name
Context
[Tree] (show subscr-mgmt steering-profile)
Full Context
show subscriber-mgmt steering-profile
Description
This command displays steering profile information.
Parameters
- steering-profile-name
-
Specifies an existing steering profile name.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
sticky-dest
sticky-dest
Syntax
sticky-dest
Context
[Tree] (tools>dump>filter>resources sticky-dest)
Full Context
tools dump filter resources sticky-dest
Description
This command displays information about resources pertaining to sticky destinations timers.
Platforms
All
Output
The following output is an example of sticky destination filter action information.
Output Example===============================================================================
Filter action - Sticky-dest resources
===============================================================================
Used : 1
Free : 2047
Total : 2048
===============================================================================
sticky-leases
sticky-leases
Syntax
sticky-leases [hostname]
Context
[Tree] (show>router>dhcp>server sticky-leases)
Full Context
show router dhcp local-dhcp-server sticky-leases
Description
This command shows either all sticky leases or a single specific sticky lease created under the specified DHCP server.
Parameters
- hostname
-
Specifies the name of the host for which an entry is created.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of sticky lease information
Output ExampleNode# show router dhcp local-dhcp-server "dhcp_server" sticky-leases
===============================================================================
DHCP Server Sticky Leases
===============================================================================
Hostname IP address
-------------------------------------------------------------------------------
test_lease 10.0.0.1
-------------------------------------------------------------------------------
No. of Matching Entries: 1
===============================================================================
Sticky Leases Field Descriptions describes the sticky leases field descriptions.
Field |
Description |
---|---|
Hostname |
The name of the sticky host |
IP address |
The IP address of the sticky host |
No. of Matching Entries |
The total numbers of entries matching the command criteria |
sticky-leases
Syntax
sticky-leases hostname [hostname]
sticky-leases hostname-prefix [hostname-prefix]
Context
[Tree] (clear>router>dhcp>server sticky-leases)
Full Context
clear router dhcp local-dhcp-server sticky-leases
Description
This command clears sticky leases.
Parameters
- hostname
-
Clears information about the name of the host for which an entry is cleared.
- hostname-prefix
-
Clears information about the sub-string of all host names starting with that sub-string.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
stop
stop
Syntax
stop
Context
[Tree] (tools>perform>router>l2tp>group stop)
Full Context
tools perform router l2tp group stop
Description
This command triggers an attempt to immediately stop all the L2TP connections within the specified L2TP tunnel group.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
stop
Syntax
stop
Context
[Tree] (tools>perform>router>l2tp>tunnel stop)
[Tree] (tools>perform>router>l2tp>group>tunnel stop)
Full Context
tools perform router l2tp tunnel stop
tools perform router l2tp group tunnel stop
Description
This command triggers an attempt to immediately stop all the L2TP connections within the specified L2TP tunnel.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
stop
Syntax
stop [script-policy-name] [owner script-policy-owner] [ all]
Context
[Tree] (tools>perform>system>script-control>script-policy stop)
Full Context
tools perform system script-control script-policy stop
Description
This command stops the execution of scripts.
Parameters
- script-policy-name
-
Specifies to only stop scripts with the specified script-policy, up to 32 characters.
- script-policy-owner
-
Specifies to only stop scripts that are associated with script-policies with the specified owner, up to 32 characters.
- all
-
Specifies to stop all running scripts.
Platforms
All
stp
stp
Syntax
stp [detail]
Context
[Tree] (show>service>id stp)
Full Context
show service id stp
Description
Displays information for the spanning tree protocol instance for the service.
Parameters
- detail
-
Displays detailed information.
Platforms
All
Output
The following output is an example of service STP information.
Output ExampleA:ALA-12# show service id 1 stp
==============================================================================
Spanning Tree Information
==============================================================================
VPLS Spanning Tree Information
------------------------------------------------------------------------------
RSTP Admin State : Up RSTP Oper State : Down
Core Connectivity : Down
Bridge-id : 04:67:ff:00:00:01
Hold Timer : 1 Bridge fwd delay : 15
Bridge Hello time : 1 Bridge max age : 20
Bridge priority : 1 Topology change : Inactive
Last Top. change : 0d 00:00:00 Top. change count : 0
Root bridge-id : 00:03:fa:00:00:00
Root path cost : 1 Root forward delay: 15
Root hello time : 1 Root max age : 20
Root priority : 0 Root port : vcp
------------------------------------------------------------------------------
Spanning Tree Specifics
------------------------------------------------------------------------------
SAP Identifier : 1/1/7:0 RSTP State : Down
STP Port State : Forwarding BPDU encap : dot1d
Port Number : 2048 Priority : 128
Cost : 10 Fast Start : Disabled
Designated Port : 34816 Designated Bridge : 02:fa:00:04:54:01
==============================================================================
A:ALA-12#
The following output is an example for the 7450 ESS.
ALA-1# show service id 1 stp
===============================================================================
Inherited Rstp State (from mVPLS), Service 1
===============================================================================
Sap/Spoke Id Oper- Prune- Port- Managed by Managed by
State State State Service Sap/spoke
-------------------------------------------------------------------------------
1/1/1:2 Down Pruned Discarding 101 1/1/1:1
100:1 Up Pruned Discarding 100 100:100
===============================================================================
Service-ID STP Field Descriptions describes show service-id STP output fields:
Label |
Description |
---|---|
RSTP Admin State |
The administrative state of the Rapid Spanning Tree Protocol instance associated with this service |
Core Connectivity |
The connectivity status to the core |
RSTP Oper State |
The operational state of the Rapid Spanning Tree Protocol instance associated with this service. This field is applicable only when STP is enabled on the router. |
Bridge-id |
The MAC address used to identify this bridge in the network. |
Hold Time |
The interval length during which no more than two Configuration BPDUs shall be transmitted by this bridge |
Bridge fwd delay |
The speed of bridge state changes when moving toward the forwarding state |
Bridge Hello time |
The amount of time between the transmission of Configuration BPDUs |
Bridge max age |
The maximum age of spanning tree protocol information learned from the network on any port before it is discarded. This is the actual value that this bridge is currently using. |
Bridge priority |
The priority of the spanning tree protocol instance associated with this service |
Topology change |
Topology change is currently in progress. |
Last Top. change |
The time (in hundredths of a second) since the last time a topology change was detected by the Spanning Tree Protocol instance associated with this service |
Top. change count |
The total number of topology changes detected by the Spanning Tree Protocol instance associated with this service since the management entity was last reset or initialized |
Root bridge-id |
The Root bridge-id |
Root path cost |
The Root path cost |
Root forward delay |
The Root forward delay |
Root hello time |
The Root hello time |
Root max age |
The Root maximum age |
Root priority |
The Root priority level |
Root port |
The Root port number |
SAP Identifier |
The SAP identifier |
RSTP State |
The RSTP state |
STP Port State |
The STP port state |
BPDU encap |
The BPDU encapsulation |
Port Number |
The port number |
Priority |
The priority level |
Cost |
The cost |
Fast Start |
The fast start state |
Designated Port |
The designated port |
Designated Bridge |
The designated bridge |
Sap/Spoke Id |
The SAP or spoke ID |
Oper-State |
The operational state |
Prune-State |
The prune state |
Port-State |
The port state |
Managed by Service |
The managed service |
Managed by Sap/spoke |
The managed SAP or spoke |
stp
streaming
streaming
Syntax
streaming
Context
[Tree] (show>oam-pm streaming)
Full Context
show oam-pm streaming
Description
Commands in this context show OAM performance monitoring telemetry report streaming information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
streaming
Syntax
streaming
Context
[Tree] (show>snmp streaming)
Full Context
show snmp streaming
Description
Commands in this context display streaming counters information.
Platforms
All
sub-ident-policy
sub-ident-policy
Syntax
sub-ident-policy [sub-ident-policy-name [ association]]
sub-ident-policy sub-ident-policy-name script { primary | secondary | tertiary}
Context
[Tree] (show>subscr-mgmt sub-ident-policy)
Full Context
show subscriber-mgmt sub-ident-policy
Description
This command displays subscriber identification policy information.
Parameters
- sub-ident-policy-name
-
Specifies an existing subscriber identification policy name.
- association
-
Displays information configured with the specified sub-ident-policy-name.
- script {primary | secondary | tertiary}
-
Displays information for the specified identification script.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber management subscriber identification policy information.
Output ExampleB:Dut-A>show>subscr-mgmt# sub-ident-policy
===============================================================================
Subscriber Identification Policies
===============================================================================
Name Description
-------------------------------------------------------------------------------
sub_ident_all
sub_ident_pc
-------------------------------------------------------------------------------
Number of Subscriber Identification Policies : 2
===============================================================================
B:Dut-A>show>subscr-mgmt#
B:Dut-A>show>subscr-mgmt# sub-ident-policy sub_ident_all
===============================================================================
Subscriber Identification Policy sub_ident_all
===============================================================================
Sub Profile Map
-------------------------------------------------------------------------------
Key Sub profile
-------------------------------------------------------------------------------
sub_prof100 sub_prof100
sub_prof110 sub_prof110
sub_prof120 sub_prof120
sub_prof130 sub_prof130
sub_prof140 sub_prof140
sub_prof230 sub_prof230
sub_prof80 sub_prof80
sub_prof81 sub_prof81
sub_prof90 sub_prof90
-------------------------------------------------------------------------------
SLA Profile Map
-------------------------------------------------------------------------------
Key SLA profile
-------------------------------------------------------------------------------
sla_prof100_VOIP sla_prof100_VOIP
sla_prof110_VOIP sla_prof110_VOIP
sla_prof120_VOIP sla_prof120_VOIP
sla_prof130_VOIP sla_prof130_VOIP
sla_prof140_VOIP sla_prof140_VOIP
sla_prof230_VOIP sla_prof230_VOIP
sla_prof80_VOIP sla_prof80_VOIP
sla_prof81_VOIP sla_prof81_VOIP
sla_prof90_VOIP sla_prof90_VOIP
-------------------------------------------------------------------------------
Python Scripts
-------------------------------------------------------------------------------
# Admin Oper Script
State State Name
-------------------------------------------------------------------------------
Primary Down Down pyTom.py
Secondary Up Up pyTomDebug.py
Tertiary Up Up hardcoded.py
===============================================================================
B:Dut-A>show>subscr-mgmt#
B:Dut-A>show>subscr-mgmt# sub-ident-policy sub_ident_all association
===============================================================================
Subscriber Identification Policy sub_ident_all
===============================================================================
SAP Associations
-------------------------------------------------------------------------------
Service-Id : 80 (VPLS)
- SAP : 1/2/1:80
Service-Id : 90 (VPLS)
- SAP : 1/2/1:90
Service-Id : 100 (VPLS)
- SAP : 1/2/1:100
- SAP : 1/2/1:101
- SAP : 1/2/1:102
Service-Id : 110 (VPLS)
- SAP : 1/2/1:110
- SAP : 1/2/1:111
- SAP : 1/2/1:112
Service-Id : 120 (VPLS)
- SAP : 1/2/1:120
- SAP : 1/2/1:121
- SAP : 1/2/1:122
Service-Id : 130 (VPLS)
- SAP : 1/2/1:130
Service-Id : 140 (VPLS)
- SAP : 1/2/1:140
===============================================================================
B:Dut-A>show>subscr-mgmt#
B:Dut-A>show>subscr-mgmt# sub-ident-policy sub_ident_all script primary
===============================================================================
Subscriber Identification Policy sub_ident_all
===============================================================================
Primary Script
-------------------------------------------------------------------------------
URL : ftp://xxx:yyy@a.b.c.d/pyTom.py
Admin State : Down Oper State : Down
-------------------------------------------------------------------------------
Source (dumped from memory)
-------------------------------------------------------------------------------
Script is not active.
-------------------------------------------------------------------------------
===============================================================================
B:Dut-A>show>subscr-mgmt#
B:Dut-A>show>subscr-mgmt# sub-ident-policy sub_ident_all script secondary
===============================================================================
Subscriber Identification Policy sub_ident_all
===============================================================================
Secondary Script
-------------------------------------------------------------------------------
URL : ftp://xxx:yyy@a.b.c.d/pyTomDebug.py
Admin State : Up Oper State : Up
-------------------------------------------------------------------------------
Source (dumped from memory)
-------------------------------------------------------------------------------
1 import alc
2 yiaddr = alc.dhcp.yiaddr
3 # Subscriber ID equals full client IP address.
4 # Note: IP address 10.10.10.10 yields 'sub-168430090'
5 # and not 'sub-10.10.10.10'
6 alc.dhcp.sub_ident = 'sub-' + str(yiaddr)
7 # DHCP server is configured such that the third byte (field) of the IP
8 # address indicates the session Profile ID.
9 alc.dhcp.sla_profile = 'sp-' + str((yiaddr & 0x0000FF00) >> 8)
===============================================================================
B:Dut-A>show>subscr-mgmt#
B:Dut-A>show>subscr-mgmt# sub-ident-policy sub_ident_all script tertiary
===============================================================================
Subscriber Identification Policy sub_ident_all
===============================================================================
Tertiary Script
-------------------------------------------------------------------------------
URL : ftp://xxx:yyy@a.b.c.d/hardcoded.py
Admin State : Up Oper State : Up
-------------------------------------------------------------------------------
Source (dumped from memory)
-------------------------------------------------------------------------------
1 from alc import dhcp
2
3 dhcp.sub_ident = 'sub_ident_A_1'
4 dhcp.sub_profile_string = 'sub_prof_B_2'
5 dhcp.sla_profile_string = 'sla_prof_C_3'
6
===============================================================================
B:Dut-A>show>subscr-mgmt#
Subscriber Identification Policy Field Descriptions describes subscriber identification policy output fields.
Field |
Description |
---|---|
Name |
The subscriber identification policy name |
Description |
The user provided description of this policy |
Number of Subscriber Identification Policies |
The total number of subscriber identification policies configured on the node |
Sub Profile Map |
The subscriber profile used to define the aggregate QoS for all hosts within a subscriber context |
Key |
The key that defines the auto-generated subscriber identification key for PPP hosts. |
Sub profile |
A list of subscriber identification profiles |
SLA profile |
A list of SLA profiles |
Admin State |
The administrative state of the Python scripts |
Oper State |
The operational state of the Python scripts |
Script Name |
The Python policy script name |
SAP Associations |
The subscriber identification policy SAP associations |
Service-Id |
The service ID associated with the subscriber identification policy |
SAP |
The SAP ID associated with the subscriber identification policy |
URL |
The URL of the script to change the Python message |
Admin State |
The admin state of the script |
Oper State |
The operational state of the script |
Primary Script |
Information about the primary Python script |
Secondary Script |
Information about the secondary Python script |
sub-mcac
sub-mcac
Syntax
sub-mcac [subscriber sub-ident-string] [ policy sub-mcac-policy-name]
Context
[Tree] (show>service>active-subscribers sub-mcac)
Full Context
show service active-subscribers sub-mcac
Description
This command displays active subscriber MCAC information.
Parameters
- sub-ident-string
-
Specifies the subscriber identification string, up to 32 characters.
- sub-mac-policy-name
-
Specifies the subscriber MAC policy name, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of active subscriber MCAC information.
Output Example*A:eng-BNG-2# show service active-subscribers sub-mcac
===============================================================================
Active Subscribers Sub-MCAC
===============================================================================
Subscriber : user_1
MCAC-policy : sub-mcac-policy-01 (inService)
In use mandatory bandwidth : 10
In use optional bandwidth : 10
Available mandatory bandwidth : 1000
Available optional bandwidth : 100
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Number of Subscribers: 1
===============================================================================
sub-mcac-policy
sub-mcac-policy
Syntax
sub-mcac-policy
sub-mcac-policy policy-name association
sub-mcac-policy policy-name
Context
[Tree] (show>subscr-mgmt sub-mcac-policy)
Full Context
show subscriber-mgmt sub-mcac-policy
Description
This command displays subscriber MCAC policy information.
Parameters
- policy-name
-
Specifies the subscriber MCAC policy name, up to 32 characters.
- association
-
Displays information associated with the subscriber MCAC policy.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s
sub-profile
sub-profile
Syntax
sub-profile [sub-profile-name [association]]
Context
[Tree] (show subscr-mgmt sub-profile)
Full Context
show subscriber-mgmt sub-profile
Description
This command displays subscriber profile information.
Parameters
- sub-profile-name
-
Specifies an existing subscriber profile name.
- association
-
Displays the association information configured with the specified sub-profile-name.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber profile information.
Output Example# show subscriber-mgmt sub-profile "sub-profile-10"
===============================================================================
Subscriber Profile sub-profile-10
===============================================================================
Description : (Not Specified)
Control plane(s) : local
Host Limits : overall 1
ipv4-overall 1
ipv4-arp 1
ipv4-dhcp 1
ipv4-ppp 1
ipv6-overall 1
ipv6-pd-overall 1
ipv6-pd-ipoe-dhcp 1
ipv6-pd-ppp-dhcp 1
ipv6-wan-overall 1
ipv6-wan-ipoe-dhcp 1
ipv6-wan-ipoe-slaac 1
ipv6-wan-ppp-dhcp 1
ipv6-wan-ppp-slaac 1
lac-overall 1
Session Limits : overall 1
ipoe 1
pppoe-overall 1
pppoe-local 1
pppoe-lac 1
l2tp-overall 1
l2tp-lns 1
l2tp-lts 1
I. Sched. Policy : N/A
E. Sched. Policy : N/A E. Agg Rate Limit: Max
E. Min Resv Bw : 1
I. Policer Ctrl. : N/A
E. Policer Ctrl. : N/A
I. vport-hashing : Disabled
I. sec-sh-hashing: Disabled
Q Frame-Based Ac*: Disabled
Acct. Policy : N/A Collect Stats : Disabled
ANCP Pol. : N/A
Accu-stats-pol : (Not Specified)
HostTrk Pol. : N/A
IGMP Policy : N/A
MLD Policy : N/A
PIM Policy : N/A
Sub. MCAC Policy : N/A
NAT Policy : N/A
Firewall Policy : N/A
UPnP Policy : N/A
NAT Prefix List : N/A
Allow NAT bypass : No
NAT access mode : auto
Def. Encap Offset: none Encap Offset Mode: none
Vol stats type : full
Preference : 5
LAG hash class : 1
LAG hash weight : 1
-------------------------------------------------------------------------------
Radius Accounting
-------------------------------------------------------------------------------
Policy : N/A
Session Opti.Stop: False
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
HS
-------------------------------------------------------------------------------
SLA-mode : expanded E Agg Rate Limit : Maximum
E. Min Resv Bw : 1
E low burst class: 6
-------------------------------------------------------------------------------
Last Mgmt Change : 09/30/2020 15:39:24
===============================================================================
* indicates that the corresponding row element may have been truncated.
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
SLA Profile Map
-------------------------------------------------------------------------------
Key SLA Profile
-------------------------------------------------------------------------------
No mappings configured.
===============================================================================
# show subscriber-mgmt sub-profile
===============================================================================
Subscriber Profiles
===============================================================================
Name Description
-------------------------------------------------------------------------------
sub_default
sub_prof100
sub_prof110
sub_prof120
sub_prof130
sub_prof140
sub_prof230
sub_prof80
sub_prof81
sub_prof90
sub_profPC1
sub_profPC2
sub_profPC3
-------------------------------------------------------------------------------
Number of Subscriber Profiles : 13
===============================================================================
A:Dut-A#
# show subscriber-mgmt sub-profile sub_prof100 association
===============================================================================
Subscriber Profile sub_prof100
-------------------------------------------------------------------------------
SAP Default-Profile Associations
-------------------------------------------------------------------------------
No associations found.
-------------------------------------------------------------------------------
SAP Static Host Associations
-------------------------------------------------------------------------------
No associations found.
-------------------------------------------------------------------------------
SAP Non-Sub-Traffic-Profile Associations
-------------------------------------------------------------------------------
No associations found.
-------------------------------------------------------------------------------
Sub-Ident-Policy Profile Map Associations
-------------------------------------------------------------------------------
Policy-name : sub_ident_all
- Key : sub_prof100
-------------------------------------------------------------------------------
Explicit Subscriber Map Associations
-------------------------------------------------------------------------------
No associations found.
===============================================================================
A:Dut-A#
Subscriber Profile Field Descriptions describes subscriber management profile field descriptions.
Field |
Description |
---|---|
Name |
The subscriber profile name |
Description |
The user provided description of this policy |
Control plane(s) |
The subscriber profile controlled by the local control plane or CUPS control plane |
I. Sched. Policy |
The ingress scheduler policy assigned to the ingress subscriber profile |
E. Sched. Policy |
The egress scheduler policy assigned to the egress subscriber profile |
E. Agg Rate Limit |
The egress aggregate rate limit |
E. Min Resv Bw |
The egress minimum reserved bandwidth |
I. Policer Ctrl |
The ingress policer control status |
E. Policer Ctrl |
The egress policer control status |
I. vport-hashing |
The ingress vport-hashing status |
I. sec-sh-hashing |
The ingress security sh hashing status |
Q Frame-Based Ac* |
The Q frame-based accounting status |
Acct. Policy |
The number of accounting policies associated with this subscriber profile |
ANCP Pol. |
The ANCP policy |
Accu-stats-pol |
The accu-stats policy |
HostTrk Pol. |
The HostTrk policy |
IGMP Policy |
The IGMP policy |
MLD Policy |
The MLD policy |
PIM Policy |
The PIM policy |
Sub. MCAC Policy |
The subscriber MCAC policy |
NAT Policy |
The NAT policy |
Host Limits |
The configured maximum number of hosts per subscriber associated with this subscriber profile |
Session Limits |
The configured maximum number of sessions per subscriber associated with this subscriber profile |
Number of Subscriber Profiles |
The total number of subscriber profiles configured on this node |
Ingress Scheduler Overrides |
Information about ingress scheduler overrides for the subscriber profile |
Scheduler |
The scheduler name |
Rate |
The scheduler rate |
CIR |
The CIR rate allowed for this scheduler |
Egress Scheduler Overrides |
Information about egress scheduler overrides for the subscriber profile |
Key |
The lookup key in the map |
SLA Profile |
Information about the SLA profile map |
Collect Stats |
The accounting statistics collected on this subscriber profile. |
Last Mgmt Change |
The time of the most recent management-initiated change |
sub-services
sub-services
Syntax
sub-services [id service-id] [sap sap-id] [ ip ip-prefix/prefix-length] [ mac ieee-address] [pppoe-session-id pppoe-session-id] [ sub-service-name sub-service-name] [sub-service-type sub-service-type] [summary | associations]
Context
[Tree] (show>service sub-services)
Full Context
show service sub-services
Description
This command displays subscriber service information.
Parameters
- service-id
-
Specifies the subscriber service ID.
- sap-id
-
Specifies the SAP ID.
- ip-prefix/ip-prefix-length
-
Specifies information for the specified IP prefix and mask length.
- ieee-address
-
Specifies the MAC address.
- pppoe-session-id
-
Specifies the PPPoE session ID.
- sub-service-name
-
Specifies the subscriber service name, up to 255 characters.
- sub-service-type
-
Specifies the subscriber service type, up to 255 characters.
- summary
-
Displays summary information.
- associations
-
Displays information associated with the subscriber service.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
subnet-ext-stats
subnet-ext-stats
Syntax
subnet-ext-stats ip-address[/mask]
subnet-ext-stats pool pool-name
Context
[Tree] (show>router>dhcp>server subnet-ext-stats)
Full Context
show router dhcp local-dhcp-server subnet-ext-stats
Description
This command displays extended statistics per DHCPv4 subnet in local DHCPv4 server.
The following statistics are included in output:
-
The number of stable leases in the subnet
-
The number of provisioned address in the subnet
-
The number of used address in the subnet
-
The number of free address in the subnet
-
The percentage of used address
-
The percentage of free address
For each statistic (except for Provisioned Addresses), there is current value and peak value, peak value is the highest value since subnet creation or last reset via the clear router rt-id dhcp local-dhcp-server svr-name subnet-ext-stats command.
When parameter pool is used, the statistics of each subnet in the pool are displayed.
Parameters
- ip-address[/mask]
-
Specifies the subnet and mask.
- pool-name
-
Specifies the name of local DHCPv4 server pool.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subnet extended statistics information.
Output Exampleshow router 500 dhcp local-dhcp-server "d4" subnet-ext-stats 239.10.10.0/24
===============================================================================
Extended statistics for subnet 239.10.10.0/24
===============================================================================
Current Peak TimeStamp
-------------------------------------------------------------------------------
Local:
Stable Leases 1 1 01/07/2013 19:38:36
Provisioned Addresses 101
Used Addresses 1 1 01/07/2013 19:38:36
Free Addresses 100 100 01/07/2013 19:38:36
Used Pct 1 1 01/07/2013 19:38:36
Free Pct 99 99 01/07/2013 19:38:36
Last Reset Time 01/07/2013 19:07:11
-------------------------------------------------------------------------------
Number of entries 1
===============================================================================
Extended Subnet Statistics Field Descriptions describes extended subnet statistics output field descriptions.
Field |
Descriptions |
---|---|
Current |
The current statistics for the subnet |
Peak |
The peak statistics for the subnet |
TimeStamp |
The timestamp for the last reset |
Stable Leases |
The number of stable leases |
Provision Addresses |
The number of provisioned addresses in this subnet |
Used Addresses |
The number of used addresses in this subnet |
Free Address |
The number of free addresses in this subnet |
Used Pct |
The percentage of addresses in this subnet in use |
Free Pct |
The percentage of addresses in this subnet currently unused |
Last Reset Time |
The time of the last reset |
Number of entries |
The total number of entries |
subnet-ext-stats
Syntax
subnet-ext-stats ip-address[/mask]
subnet-ext-stats pool pool-name
Context
[Tree] (clear>router>dhcp>server subnet-ext-stats)
Full Context
clear router dhcp local-dhcp-server subnet-ext-stats
Description
This command clears extended subnet statistics.
Parameters
- ip-address[/mask]
-
Clears the specified IP address and mask.
- pool-name
-
Clears statistics for the specified pool name.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
subnet-stats
subnet-stats
Syntax
subnet-stats ip-address[/mask]
subnet-stats pool pool-name
Context
[Tree] (show>router>dhcp>server subnet-stats)
Full Context
show router dhcp local-dhcp-server subnet-stats
Description
This command displays subnet statistics.
Parameters
- ip-address[/mask]
-
Specifies the subnet and mask.
- pool-name
-
Specifies the name of local DHCPv4 server pool.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subnet statistics information.
Output Example*A:SUB-Dut-A# show router dhcp local-dhcp-server dhcpS2 subnet-stats pool POOL2
===============================================================================
Statistics for pool POOL2
===============================================================================
Subnet Free Offered Stable
FRPending RemPending Declined
-------------------------------------------------------------------------------
10.0.0.0/8 16384 0 0
0 0 0
-------------------------------------------------------------------------------
No. of entries: 1
===============================================================================
*A:SUB-Dut-A#
Subnet Stats Pool Field Descriptions describe the fields for subnet stats pool output.
Field |
Description |
---|---|
Subnet |
The subnet address |
Free |
The number of addresses in this subnet that are free |
Offered |
The number of leases in this subnet that are in state offered |
Stable |
The number of leases in this subnet that are in state stable |
FRPending |
The number of leases in this subnet that are in state forceRenewPending |
RemPending |
The number of leases in this subnet that are in state removePending |
Declined |
The number of addresses in this subnet that are declined |
No. of entries |
The total number of entries |
subscribe-to
subscribe-to
Syntax
subscribe-to log-id log-id
Context
[Tree] (tools>perform>log subscribe-to)
Full Context
tools perform log subscribe-to
Description
This command subscribes the current CLI session to the specified CLI log. Log events for the specified log will be output in the current CLI session until the CLI session closes or an unsubscribe-from command is used.
Parameters
- log-id
-
Specifies the log ID for which subscription is requested.
Platforms
All
subscriber
subscriber
Syntax
subscriber sub-ident-string sap sap-id sla-profile sla-profile-name [scheduler scheduler-name] [spi-sharing-type spi-sharing-type] [spi-sharing-id spi-sharing-id]
subscriber sub-ident-string [scheduler scheduler-name] [ingress | egress]
Context
[Tree] (clear>qos>scheduler-stats subscriber)
Full Context
clear qos scheduler-stats subscriber
Description
This command clears scheduler stats by subscriber.
Parameters
- sub-ident-string
-
Clears information for the specified subscriber name.
- sap-id
-
Clears information for the specified SAP.
- sla-profile-name
-
Clears information for the specified SLA profile name.
- scheduler-name
-
Clears information for the specified scheduler.
- spi-sharing-type
-
Clears information for sessions with the specified SPI sharing type.
- spi-sharing-id
-
Clears information for sessions with the specified SPI sharing type and sharing identifier. The SPI group identifier is:
-
an identifier when the sharing type is per-group
-
an internal PPP or IPoE sharing identifier when the sharing type is a per-PPP or per-IPoE session
-
- egress
-
Clears egress information for the subscriber.
- ingress
-
Clears ingress information for the subscriber.
Platforms
All
subscriber
Syntax
subscriber sub-ident-string
Context
[Tree] (clear>service>statistics subscriber)
Full Context
clear service statistics subscriber
Description
This command clears the statistics for a particular subscriber.
Parameters
- sub-ident-string
-
Clears statistics for the specified subscriber identification string.
Platforms
All
subscriber
Syntax
subscriber sub-ident-string
subscriber sub-ident-string detail
subscriber sub-ident-string mirror
subscriber sub-ident-string sap sap-id sla-profile sla-profile-name [spi-sharing-type spi-sharing-type] [spi-sharing-id spi-sharing-id]
subscriber sub-ident-string sap sap-id sla-profile sla-profile-name [spi-sharing-type spi-sharing-type] [spi-sharing-id spi-sharing-id] detail
subscriber sub-ident-string sap sap-id sla-profile sla-profile-name [spi-sharing-type spi-sharing-type] [spi-sharing-id spi-sharing-id] mirror
Context
[Tree] (show>service>active-subscribers subscriber)
Full Context
show service active-subscribers subscriber
Description
This command displays active subscriber information for a subscriber.
Parameters
- sub-ident-string
-
Displays the subscriber ID of the active subscriber, up to 32 characters.
- sap-id
-
Displays the physical port identifier portion of the SAP definition.
- sla-profile-name
-
Displays the existing SLA profile name, up to 32 characters.
- spi-sharing-type
-
Displays subscriber information for sessions with the specified SPI sharing type.
- spi-sharing-id
-
Displays subscriber information for sessions with the specified SPI sharing type and sharing identifier. The SPI group ID is:
-
a group id when sharing type is per-group
-
an internal PPP or IPoE sharing id when the sharing type is per-PPP or per-IPoE session
-
- detail
-
Displays detailed output.
- mirror
-
Displays mirrored output.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber information for active subscribers.
Output Example*A:eng-BNG-2# show service active-subscribers subscriber "user_1"
===============================================================================
Active Subscribers
===============================================================================
-------------------------------------------------------------------------------
Subscriber user_1
(no-prof)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
(1) SLA Profile Instance sap:1/1/20:841 - sla:no-prof
-------------------------------------------------------------------------------
IP Address
MAC Address Session Origin Svc Fwd
-------------------------------------------------------------------------------
192.168.0.14
00:00:10:10:12:13 N/A DHCP 1000 Y
-------------------------------------------------------------------------------
===============================================================================
subscriber
Syntax
subscriber sub-ident-string [{ingress | egress}] [{detail | root-detail | thresholds | priority-info | depth}] [port port-id] [ arbiter {name | root}]
Context
[Tree] (show>qos>policer-hierarchy subscriber)
Full Context
show qos policer-hierarchy subscriber
Description
This command displays information about the policer hierarchy per subscriber.
Parameters
- sub-ident-string
-
Displays information about the specified subscriber.
- ingress
-
Displays ingress information about the specified subscriber.
- egress
-
Displays egress information about the specified subscriber.
- detail
-
Displays detailed information.
- root-detail
-
Displays detailed information about the arbiter root.
- thresholds
-
Displays threshold, parenting, rate, and traffic information related to a policer.
- priority-info
-
Displays threshold information related to the root arbiter.
- depth
-
Displays bucket depth, parenting, rate, and traffic information related to a policer.
- port-id
-
Displays information about the specified port.
- name
-
Displays information about the named QoS arbiter.
- root
-
Displays information about the arbiter root.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
subscriber
Syntax
subscriber sub-ident-string [scheduler scheduler-name] [{ingress | egress}] [detail]
subscriber sub-ident-string sla-profile sla-profile-name sap sap-id [ scheduler scheduler-name] [detail] [ spi-sharing-type spi-sharing-type] [ spi-sharing-id spi-sharing-id]
Context
[Tree] (show>qos>scheduler-hierarchy subscriber)
Full Context
show qos scheduler-hierarchy subscriber
Description
This command displays the scheduler hierarchy per subscriber.
Parameters
- sub-ident-string
-
Displays the subscriber identification policy name.
- scheduler-name
-
Displays the scheduler name.
- ingress
-
Displays ingress SAP subscriber scheduler stats.
- egress
-
Displays egress SAP subscriber scheduler stats.
- detail
-
Displays detailed information.
- sla-profile-name
-
Displays information for the specified sla-profile-name.
- spi-sharing-type
-
Displays subscriber scheduler hierarchy information for sessions with the specified SLA Profile Instance sharing type.
- spi-sharing-id
-
Displays subscriber scheduler hierarchy information for sessions with the specified SLA Profile Instance sharing type and sharing identifier. The spi-sharing-id is:
-
a group id when sharing type is per-group
-
an internal PPP or IPoE sharing id when the grouping type is per-PPP or per-IPoE-session
-
Platforms
All
Output
The following output is an example of QoS scheduler hierarchy subscriber information, and Show QoS Scheduler-Hierarchy Subscriber Output Fields describes the QoS scheduler hierarchy subscriber fields.
Output Example*A:PE# show qos scheduler-hierarchy subscriber "sub1"
===============================================================================
Scheduler Hierarchy - Subscriber sub1
===============================================================================
Ingress Scheduler Policy: basic-upstream-policy
Egress Scheduler Policy : basic-downstream-policy
-------------------------------------------------------------------------------
Root (Ing)
| slot(1)
|--(S) : basic-upstream
| |
| |--(Q) : Sub=sub1:basic-sla 200->1/1/1:1->2 1-1
| |
| |--(Q) : Sub=sub1:basic-sla 200->1/1/1:1->1 1-1
| |
Root (Egr)
| slot(1)
|--(S) : basic-downstream (Port 1/1/1)
| |
| |--(Q) : Sub=sub1:basic-sla 200->1/1/1:1->1
| |
|
===============================================================================
*A:PE#
*A:PE# show qos scheduler-hierarchy subscriber "sub1" detail
===============================================================================
Scheduler Hierarchy - Subscriber sub1
===============================================================================
Ingress Scheduler Policy: basic-upstream-policy
Egress Scheduler Policy : basic-downstream-policy
-------------------------------------------------------------------------------
Legend :
(*) real-time dynamic value
(w) Wire rates
B Bytes
-------------------------------------------------------------------------------
Root (Ing)
| slot(1)
|--(S) : basic-upstream
| | AdminPIR:max AdminCIR:0(sum)
| | Limit Unused Bandwidth: disabled
| |
| |
| | [Within CIR Level 0 Weight 0]
| | Assigned:0 Offered:0
| | Consumed:0
| |
| | [Above CIR Level 0 Weight 0]
| | Assigned:0 Offered:0
| | Consumed:0
| |
| |
| | TotalConsumed:0
| | OperPIR:max
| |
| | [As Parent]
| | Rate:max
| | ConsumedByChildren:0
| |
| |
| |--(Q) : Sub=sub1:basic-sla 200->1/1/1:1->2 1-1
| | | AdminPIR:1000000 AdminCIR:0
| | | Parent Limit Unused Bandwidth: not-found
| | | CBS:31457280 B
| | | MBS:51904512 B
| | | Depth:0 B
| | | HighPlus Drop Tail:51904512 B
| | | High Drop Tail:51904512 B
| | | Low Drop Tail:46399488 B
| | | Exceed Drop Tail:40894464 B
| | |
| | | [Within CIR Level 0 Weight 1]
| | | Assigned:0 Offered:0
| | | Consumed:0
| | |
| | | [Above CIR Level 1 Weight 1]
| | | Assigned:1000000 Offered:0
| | | Consumed:0
| | |
| | | TotalConsumed:0
| | | OperPIR:max OperCIR:0
| | | OperFIR:0
| | |
| | | PktByteOffset:add 0*
| | | OnTheWireRates:false
| | | ATMOnTheWireRates:false
| | | LastMileOnTheWireRates:false
| |
| |--(Q) : Sub=sub1:basic-sla 200->1/1/1:1->1 1-1
| | | AdminPIR:10000 AdminCIR:0
| | | Parent Limit Unused Bandwidth: not-found
| | | CBS:10420224 B
| | | MBS:20840448 B
| | | Depth:0 B
| | | HighPlus Drop Tail:20840448 B
| | | High Drop Tail:20840448 B
| | | Low Drop Tail:20840448 B
| | | Exceed Drop Tail:16515072 B
| | |
| | | [Within CIR Level 0 Weight 1]
| | | Assigned:0 Offered:0
| | | Consumed:0
| | |
| | | [Above CIR Level 1 Weight 1]
| | | Assigned:10000 Offered:0
| | | Consumed:0
| | |
| | | TotalConsumed:0
| | | OperPIR:10000 OperCIR:0
| | | OperFIR:0
| | |
| | | PktByteOffset:add 0*
| | | OnTheWireRates:false
| | | ATMOnTheWireRates:false
| | | LastMileOnTheWireRates:false
| |
Root (Egr)
| slot(1)
|--(S) : basic-downstream (Port 1/1/1)
| | AdminPIR:max AdminCIR:0(sum)
| | Parent Limit Unused Bandwidth: not-found
| |
| | AvgFrmOv:100.00
| | AdminPIR:max(w) AdminCIR:0(w)
| |
| | [Within CIR Level 0 Weight 0]
| | Assigned:0(w) Offered:0(w)
| | Consumed:0(w)
| |
| | [Above CIR Level 1 Weight 1]
| | Assigned:1000000(w) Offered:0(w)
| | Consumed:0(w)
| |
| |
| | TotalConsumed:0(w)
| | OperPIR:1000000
| |
| | [As Parent]
| | Rate:1000000
| | ConsumedByChildren:0
| |
| |
| |--(Q) : Sub=sub1:basic-sla 200->1/1/1:1->1
| | | AdminPIR:1000000 AdminCIR:0
| | | Parent Limit Unused Bandwidth: not-found
| | | AvgFrmOv:100.00
| | | CBS:0 B
| | | MBS:1253376 B
| | | Depth:0 B
| | | HighPlus Drop Tail:1253376 B
| | | High Drop Tail:1253376 B
| | | Low Drop Tail:1253376 B
| | | Exceed Drop Tail:983040 B
| | |
| | | [Within CIR Level 0 Weight 1]
| | | Assigned:0 Offered:0
| | | Consumed:0
| | |
| | | [Above CIR Level 1 Weight 1]
| | | Assigned:1000000 Offered:0
| | | Consumed:0
| | |
| | | TotalConsumed:0
| | | OperPIR:max OperCIR:0
| | |
| | | PktByteOffset:add 0*
| | | OnTheWireRates:false
| | | ATMOnTheWireRates:false
| | | LastMileOnTheWireRates:false
| |
|
===============================================================================
*A:PE#
Label |
Description |
---|---|
Legend |
Admin CIR/PIR: Specifies the configured value of CIR/PIR. Assigned CIR/PIR: Specifies the PIR/CIR rate given to a member by that parent level. Offered CIR/PIR: Specifies the offered load on that member. Consumed CIR/PIR: Specifies the amount of scheduler bandwidth used by this member. |
PIR |
Specifies the PIR rate. |
CIR |
Specifies the CIR rate. |
S |
Displays the scheduler name. |
Q |
Displays the queue ID and information. |
subscriber
Syntax
subscriber sub-ident-string sap sap-id sla-profile sla-profile-name [scheduler scheduler-name] [spi-sharing-type spi-sharing-type] [spi-sharing-id spi-sharing-id]
subscriber sub-ident-string [scheduler scheduler-name] [{ingress | egress}]
Context
[Tree] (show>qos>scheduler-stats subscriber)
Full Context
show qos scheduler-stats subscriber
Description
This command displays scheduler statistics information.
Parameters
- sub-ident-string
-
Specifies an existing SLA profile string.
- scheduler-name
-
Specifies an existing scheduler name.
- ingress
-
Display only the policy displayed on ingress.
- egress
-
Display only the policy displayed on egress.
- sla-profile-name
-
Displays information for the specified sla-profile-name.
- spi-sharing-type
-
Displays subscriber scheduler hierarchy information for sessions with the specified SLA Profile Instance sharing type.
- spi-sharing-id
-
Displays subscriber scheduler hierarchy information for sessions with the specified SLA Profile Instance sharing type and sharing identifier. The spi-sharing-id is:
-
a group id when sharing type is per-group
-
an internal PPP or IPoE sharing id when the sharing type is per-PPP or per-IPoE-session
-
Platforms
All
Output
The following output is an example of QoS scheduler-stats subscriber information, and Show QoS Scheduler-Stats Subscriber Output Fields describes the QoS scheduler-stats subscriber fields.
Output ExampleA:D# show qos scheduler-stats subscriber RoutedCoHost1
===============================================================================
Scheduler Stats
===============================================================================
Scheduler Forwarded Packets Forwarded Octets
-------------------------------------------------------------------------------
Ingress Schedulers
gp 0 0
Egress Schedulers
gp 0 0
mb 0 0
mbs 0 0
pb 0 0
pbs 0 0
rb 0 0
rbs 0 0
===============================================================================
*A:D#
Label |
Description |
---|---|
Scheduler |
Displays the scheduler policy name. |
Forwarded Packets |
Displays the number of packets forwarded. |
Forwarded Octet |
Displays the number of octets forwarded. |
subscriber
Syntax
subscriber sub-indent-string [egress] [detail]
Context
[Tree] (show>qos>agg-rate subscriber)
Full Context
show qos agg-rate subscriber
Description
This command displays the H-QoS aggregate rate limit per subscriber.
Parameters
- sub-indent-string
-
Specifies the subscriber identification string of the subscriber.
- egress
-
Displays egress SAP customer scheduler stats.
- detail
-
Displays detailed information.
Platforms
All
Output
The following output is an example of H-QoS aggregate rate limit per subscriber, and Show H-QoS Aggregate Rate Limit per Subscriber Fields describes the H-QoS aggregate rate limit per subscriber fields.
Output Example*A:PE1# show qos agg-rate subscriber "sub1" egress
===============================================================================
Aggregate Rate Information - Subscriber sub1
===============================================================================
-------------------------------------------------------------------------------
Root (Egr)
| slot(1)
| AdminRate : 1000
| OperRate : 0
| Limit Unused Bandwidth : disabled
| OnTheWireRates : false
| LastMileOnTheWireRates : false
|
|--(Q) : Sub=sub1:basic-sla 1->1/1/1:1->1 (Port 1/1/1)
|
===============================================================================
*A:PE#
Label |
Description |
---|---|
AdminRate |
Displays the configured aggregate rate in the subscriber profile. |
OperRate |
Displays the actual downstream rate. |
Limit Unused Bandwidth |
Indicates whether the limit-unused-bandwidth command is enabled to protect against exceeding the aggregated bandwidth |
OnTheWireRates |
Indicates whether the displayed rates are on-the-wire rates. |
LastMileOnTheWireRates |
Indicates whether the displayed rates are on-the-wire rates for the last mile only. |
subscriber
Syntax
subscriber sub-ident-string sap sap-id sla-profile sla-profile-name [repeat repeat] [ absolute | rate] [base]
subscriber sub-ident-string sap sap-id sla-profile sla-profile-name [repeat repeat] [ absolute | rate] egress-policer-id egress-policer-id
subscriber sub-ident-string sap sap-id sla-profile sla-profile-name [repeat repeat] [ absolute | rate] egress-queue-id egress-queue-id
subscriber sub-ident-string sap sap-id sla-profile sla-profile-name [repeat repeat] [ absolute | rate] ingress-policer-id ingress-policer-id
subscriber sub-ident-string sap sap-id sla-profile sla-profile-name [repeat repeat] [ absolute | rate] ingress-queue-id ingress-queue-id
Context
[Tree] (monitor>service subscriber)
Full Context
monitor service subscriber
Description
This command monitors statistics for a subscriber.
Parameters
- sub-ident-string
-
Specifies an existing subscriber identification profile to monitor, up to 32 characters.
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- sla-profile-name
-
Specifies an existing SLA profile. The name can be a maximum of 32 characters long.
- seconds
-
Configures the interval for each display, in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
- base
-
Monitor base statistics.
- egress-policer-id
-
Monitors statistics for the policer.
- egress-queue-id
-
Monitors statistics for this queue.
- ingress-policer-id
-
Monitors statistics for this policer.
- ingress-queue-id
-
Monitors statistics for this queue.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber-information.
Output ExampleA:Dut-A# monitor service subscriber nokia_100 sap 1/2/1:101 sla-profile sla_
default
===============================================================================
Monitor statistics for Subscriber nokia_100
===============================================================================
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
SLA Profile Instance statistics
-------------------------------------------------------------------------------
Packets Octets
Off. HiPrio : 0 0
Off. LowPrio : 94531 30704535
Off. Uncolor : 0 0
Queueing Stats (Ingress QoS Policy 1000)
Dro. HiPrio : 0 0
Dro. LowPrio : 7332 2510859
For. InProf : 0 0
For. OutProf : 87067 28152288
Queueing Stats (Egress QoS Policy 1000)
Dro. InProf : 880 127660
Dro. OutProf : 0 0
For. InProf : 90862 12995616
For. OutProf : 0 0
-------------------------------------------------------------------------------
SLA Profile Instance per Queue statistics
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 2 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 94531 30704535
Off. Uncolor : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 7332 2510859
For. InProf : 0 0
For. OutProf : 87067 28152288
Ingress Queue 3 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Ingress Queue 11 (Multipoint) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Egress Queue 1
Dro. InProf : 880 127660
Dro. OutProf : 0 0
For. InProf : 90862 12995616
For. OutProf : 0 0
Egress Queue 2
Dro. InProf : 0 0
Dro. OutProf : 0 0
For. InProf : 0 0
For. OutProf : 0 0
Egress Queue 3
Dro. InProf : 0 0
Dro. OutProf : 0 0
For. InProf : 0 0
For. OutProf : 0 0
===============================================================================
A:Dut-A#
A:Dut-A# monitor service subscriber nokia_100 sap 1/2/1:101 sla-
profile sla_default base rate
===============================================================================
Monitor statistics for Subscriber nokia_100
===============================================================================
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
SLA Profile Instance statistics
-------------------------------------------------------------------------------
Packets Octets
Off. HiPrio : 0 0
Off. LowPrio : 109099 35427060
Off. Uncolor : 0 0
Queueing Stats (Ingress QoS Policy 1000)
Dro. HiPrio : 0 0
Dro. LowPrio : 8449 2894798
For. InProf : 0 0
For. OutProf : 100523 32489663
Queueing Stats (Egress QoS Policy 1000)
Dro. InProf : 880 127660
Dro. OutProf : 0 0
For. InProf : 105578 15104553
For. OutProf : 0 0
-------------------------------------------------------------------------------
At time t = 11 sec (Mode: Rate)
-------------------------------------------------------------------------------
SLA Profile Instance statistics
-------------------------------------------------------------------------------
Packets Octets % Port
Util.
Off. HiPrio : 0 0 0.00
Off. LowPrio : 1469 477795 0.38
Off. Uncolor : 0 0 0.00
Queueing Stats (Ingress QoS Policy 1000)
Dro. HiPrio : 0 0 0.00
Dro. LowPrio : 119 40691 0.03
For. InProf : 0 0 0.00
For. OutProf : 1349 437350 0.34
Queueing Stats (Egress QoS Policy 1000)
Dro. InProf : 0 0 0.00
Dro. OutProf : 0 0 0.00
For. InProf : 1469 209129 0.16
For. OutProf : 0 0 0.00
===============================================================================
A:Dut-A#
A:Dut-A# monitor service subscriber nokia_100 sap 1/2/1:101 sla-
profile sla_ default ingress-queue-id 1
===============================================================================
Monitor statistics for Subscriber nokia_100
===============================================================================
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
Packets Octets
Ingress Queue 1 (Unicast) (Priority)
Off. HiPrio : 0 0
Off. LowPrio : 0 0
Off. Uncolor : 0 0
Dro. HiPrio : 0 0
Dro. LowPrio : 0 0
For. InProf : 0 0
For. OutProf : 0 0
===============================================================================
A:Dut-A#
A:Dut-A# monitor service subscriber nokia_100 sap 1/2/1:101 sla-profile
sla_default egress-queue-id 1
===============================================================================
Monitor statistics for Subscriber nokia_100
-------------------------------------------------------------------------------
At time t = 0 sec (Base Statistics)
-------------------------------------------------------------------------------
Packets Octets
Egress Queue 1
Dro. InProf : 880 127660
Dro. OutProf : 0 0
For. InProf : 164366 23506178
For. OutProf : 0 0
===============================================================================
A:Dut-A#
subscriber
Syntax
subscriber sub-ident-string [arbiter {root | name}] [ingress | egress] [interval seconds] [repeat repeat] [absolute | rate]
Context
[Tree] (monitor>qos>arbiter-stats subscriber)
Full Context
monitor qos arbiter-stats subscriber
Description
This command monitors arbiter statistics for a subscriber.
Parameters
- sub-ident-string
-
Specifies an existing subscriber identification policy name, up to 32 characters.
- name
-
Specifies the name of the policer control policy arbiter.
- root
-
Specifies the arbiter to which this queue would be feeding.
- ingress
-
Displays arbiter name statistics applied on the ingress SAP.
- egress
-
Displays arbiter name statistics applied on the egress SAP.
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
subscriber
Syntax
subscriber sub-ident-string [scheduler scheduler-name] [ ingress | egress] [interval seconds] [ repeat repeat] [absolute | rate]
subscriber sub-ident-string [interval seconds] [repeat repeat] [absolute | rate] sap sap-id sla-profile sla-profile-name
Context
[Tree] (monitor>qos>scheduler-stats subscriber)
Full Context
monitor qos scheduler-stats subscriber
Description
This command monitors scheduler statistics for a subscriber.
Parameters
- sub-ident-string
-
Specifies an existing subscriber identification policy name, up to 32 characters.
- scheduler-name
-
Specifies an existing QoS scheduler policy name, up to 32 characters. Scheduler names are configured in the config>qos>scheduler-policy>tier level context.
- ingress
-
Displays scheduler-name statistics applied on the ingress SAP.
- egress
-
Displays scheduler-name statistics applied on the egress SAP.
- seconds
-
Configures the interval for each display in seconds.
- repeat
-
Configures how many times the command is repeated.
- absolute
-
Displays raw statistics, without processing. No calculations are performed on the delta or rate statistics.
- rate
-
Displays rate-per-second for each statistic instead of the delta.
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- sla-profile-name
-
Specifies the SLA profile belonging to the subscriber host, up to 32 characters.
Platforms
All
subscriber
Syntax
subscriber sub-ident-string [arbiter {name | root}] [ingress | egress]
Context
[Tree] (clear>qos>arbiter-stats subscriber)
Full Context
clear qos arbiter-stats subscriber
Description
This command clears the arbiter statistics per subscriber.
Parameters
- sub-ident-string
-
Specifies the subscriber identification policy name, up to 32 characters.
- name
-
Specifies the arbiter name, up to 32 characters.
- root
-
Specifies the arbiter root, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
subscriber
Syntax
subscriber id subscriber-id [statistics]
subscriber all [statistics]
Context
[Tree] (clear>subscr-mgmt>host-tracking subscriber)
Full Context
clear subscriber-mgmt host-tracking subscriber
Description
This command clears the host tracking data for a subscriber.
Parameters
- subscriber-id
-
Specifies subscriber ID, up to 32 characters.
- all
-
Clears all host tracking data.
- statistics
-
Clears statistical host tracking information for the specified subscriber ID.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
subscriber
Syntax
subscriber sub-ident-string [arbiter name | root] [ingress | egress]
Context
[Tree] (show>qos>arbiter-stats subscriber)
Full Context
show qos arbiter-stats subscriber
Description
This command displays the arbiter statistics per subscriber.
Parameters
- sub-ident-string
-
Displays information about the specified subscriber, up to 32 characters for the 7950 XRS and VSR platforms and up to 64 characters for all other platforms.
- name
-
Specifies the arbiter name, up to 32 characters.
- root
-
Specifies the arbiter root, up to 32 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
subscriber
Syntax
subscriber sub-ident-string [sla-profile sla-profile-name] [ingress | egress] [detail] [ port port-id]
Context
[Tree] (show>qos>policer subscriber)
Full Context
show qos policer subscriber
Description
This command displays the policer statistics per port.
Parameters
- sub-ident-string
-
Displays information about the specified subscriber, up to 32 characters for the 7950 XRS and VSR platforms and up to 64 characters for all other platforms.
- sla-profile-name
-
Specifies the queue group name, up to 32 characters.
- port-id
-
Displays information about the specified port.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, 7950 XRS, VSR
subscriber-hosts
subscriber-hosts
Syntax
subscriber-hosts
Context
[Tree] (clear>service>id subscriber-hosts)
Full Context
clear service id subscriber-hosts
Description
Commands in this context clear information for a particular subscriber host.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
subscriber-hosts
Syntax
subscriber-hosts [sap sap-id] [ip ip-prefix/prefix-length] [mac ieee-address] [ sub-profile sub-profile-name] [sla-profile sla-profile-name] [ app-profile app-profile-name] [wholesaler service-id] [address-origin address-origin] [detail] [ statistics] [spi-sharing-type spi-sharing-type] [spi-sharing-id spi-sharing-id]
Context
[Tree] (show>service>id subscriber-hosts)
Full Context
show service id subscriber-hosts
Description
This command displays subscriber host information.
Parameters
- sap-id
-
Specifies the physical port identifier portion of the SAP definition.
- ip-prefix/prefix-length
-
Shows information for the specified IP address and mask.
- ieee-address
-
Displays information only for the specified 48-bit MAC address. The MAC address can be expressed in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd- ee-ff where aa, bb, cc, dd, ee and ff are hexadecimal numbers.
- sub-profile-name
-
Displays an existing subscriber profile name to be associated with the static subscriber host. The subscriber profile is configured in the config>subscr-mgmt>sub-profile context.
- sla-profile-name
-
Displays subscriber host information for hosts with the specified SLA profile name.
- app-profile-name
-
Specifies an existing SLA app profile name, up to 32 characters.
- service-id
-
Specifies the ID that uniquely identifies a service.
- address-origin
-
Specifies an address origin.
- detail
-
Displays detailed information.
- statistics
-
Displays the HTTP redirect statistics for the host. The redirect statistics are divided into HTTP GET and HTTP response for redirection.
- spi-sharing-type
-
Displays subscriber host information for hosts with the specified SPI sharing type.
- spi-sharing-id
-
Displays subscriber host information for hosts with the specified SPI sharing type and sharing identifier. The SPI group ID is:
-
a sharing ID when the sharing type is per-group
-
an internal PPP or IPoE sharing ID when the sharing type is per-PPP or per-IPoE session
-
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber host information.
Output Example*A:Dut-C># show service id 3 subscriber-hosts
=============================================================
Subscriber Host table
=============================================================
Sap Subscriber
IP Address
MAC Address PPPoE-SID Origin Fwding State
-------------------------------------------------------------
2/1/5:2 TEACAHEH74
10.11.1.61
00:80:00:00:00:0a N/A ARP-Host Fwding
[pw-11:11] VIACAHEH74
10.11.1.2
00:00:11:11:01:02 N/A ARP-Host Fwding
[pw-11:12] pw-11:12
10.11.1.3
00:00:11:11:01:03 N/A ARP-Host Fwding
[pw-11:13] pw-11:13
10.11.1.4
00:00:11:11:01:04 N/A ARP-Host Fwding
[pw-22:22] XMACAHEH74
10.22.1.2
00:00:22:22:01:02 N/A ARP-Host Fwding
[pw-33:33] IUASAHEH74
10.33.1.2
00:00:33:33:01:02 N/A ARP-Host Fwding
-------------------------------------------------------------
Number of subscriber hosts: 6
=============================================================
*A:Dut-C>#
A:Dut-A# show service id 100 subscriber-hosts ip 10.100.1.5
===============================================================================
Subscriber Host table
===============================================================================
Sap IP Address MAC Address Origin(*) Subscriber
-------------------------------------------------------------------------------
1/2/1:102 10.100.1.5 00:10:00:00:00:03 -/D/- nokia_100
-------------------------------------------------------------------------------
Number of subscriber hosts : 1
===============================================================================
(*) S=Static Host, D=DHCP Lease, N=Non-Sub-Traffic
A:Dut-A#
The following table describes show service-id subscriber hosts output fields:
Label |
Description |
---|---|
Sap |
The physical port identifier portion of the SAP definition. |
IP Address |
The IP address |
MAC Address |
The MAC address |
PPPoE-SID |
The PPPoE-SID of the originating subscriber |
Origin Subscriber |
The ID of the originating subscriber |
Fwding State |
The forwarding state |
Number of subscriber hosts |
The number of subscriber hosts |
subscriber-identification
subscriber-identification
Syntax
subscriber-identification
Context
[Tree] (show>router>nat subscriber-identification)
Full Context
show router nat subscriber-identification
Description
This command displays the NAT subscriber identification information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
subscriber-identification
Syntax
subscriber-identification subscriber-string subscriber-string
Context
[Tree] (clear>nat subscriber-identification)
Full Context
clear nat subscriber-identification
Description
This command clears NAT subscriber identification information.
Parameters
- subscriber-string
-
Specifies the subscriber identification string, up to 64 characters.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
subscriber-mgmt
subscriber-mgmt
Syntax
subscriber-mgmt
Context
[Tree] (clear subscriber-mgmt)
Full Context
clear subscriber-mgmt
Description
This command enables the contect to clear subscriber management data.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
subscriber-mgmt
Syntax
subscriber-mgmt
Context
[Tree] (tools>perform subscriber-mgmt)
Full Context
tools perform subscriber-mgmt
Description
This command enables tools to control subscriber management.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
subscriber-mgmt
Syntax
subscriber-mgmt
Context
[Tree] (tools>dump subscriber-mgmt)
Full Context
tools dump subscriber-mgmt
Description
Commands in this context display subscriber management resources.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
subscriber-mgmt
Syntax
subscriber-mgmt
Context
[Tree] (show subscriber-mgmt)
Full Context
show subscriber-mgmt
Description
Commands in this context display subscriber management statistics.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
subscriber-using
subscriber-using
Syntax
subscriber-using [service-id service-id] [ sap-id sap-id] [interface ip-int-name] [ ip ip-address[/mask]] [mac ieee-address] [sub-profile sub-profile-name] [ sla-profile sla-profile-name] [app-profile app-profile-name] [ port port-id] [no-inter-dest-id | inter-dest-id intermediate-destination-id]
Context
[Tree] (show>service subscriber-using)
Full Context
show service subscriber-using
Description
This command displays selective subscriber information using specific options.
Parameters
- service-id
-
Specifies the ID that uniquely identifies a service.
- sap-id
-
Displays the physical port identifier portion of the SAP definition.
- ip-int-name
-
Shows DHCP statistics on the specified interface.
- port-id
-
Indicates the SAP or SDP for which this entry contains information.
- ip-address[/mask]
-
Shows information for the specified IP address and mask.
- ieee-address
-
Displays information only for the specified 48-bit MAC address. The MAC address can be expressed in the form aa:bb:cc:dd:ee:ff or aa-bb-cc-dd- ee-ff where aa, bb, cc, dd, ee and ff are hexadecimal numbers.
- sub-profile-name
-
Displays an existing subscriber profile name to be associated with the static subscriber host. The subscriber profile is configured in the config>subscr-mgmt>sub-profile context.
- sla-profile-name
-
Specifies an existing SLA profile name.
- app-profile-name
-
Displays the profile of the specified application.
- intermediate-destination-id
-
Indicates the intermediate destination identifier received from either the DHCP or RADIUS server, or the local user database.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of selective subscriber information.
Output ExampleA:Dut-A# show service subscriber-using service-id 100
=================================================================
Subscribers
=================================================================
Subscriber Sub Profile
-----------------------------------------------------------------
nokia_100 sub_prof100
-----------------------------------------------------------------
Matching Subscribers : 1
=================================================================
A:Dut-A#
A:Dut-A# show service subscriber-using
=================================================================
Subscribers
=================================================================
Subscriber Sub Profile
-----------------------------------------------------------------
nokia_100 sub_prof100
nokia_110 sub_prof110
nokia_120 sub_prof120
nokia_130 sub_prof130
nokia_80 sub_prof80
nokia_90 sub_prof90
client_PC1 sub_profPC1
static sub_default
-----------------------------------------------------------------
Matching Subscribers : 8
=================================================================
A:Dut-A#
Subscriber Using Service ID Field Descriptions describes subscriber using a specified service ID field descriptions.
Field |
Description |
---|---|
Subscriber |
The subscriber name |
Sub Profile |
The subscriber profile name |
Matching Subscribers |
The number of subscribers matching the search criteria |
subscription
subscription
Syntax
subscription subscription-id [paths]
subscription
Context
[Tree] (show>system>telemetry>grpc subscription)
Full Context
show system telemetry grpc subscription
Description
This command displays the active telemetry gRPC subscriptions.
Parameters
- subscription-id
-
A unique subscription ID or number that is assigned by the SR OS gRPC server to each active telemetry subscription.
- paths
-
Indicates that the show command output includes all paths with the respective subscription ID information.
Platforms
All
Output
The following output is an example of the telemetry gRPC subscription information.
Output ExampleA:node-6>show>system>telemetry>grpc# subscription
===============================================================================
Telemetry gRPC subscriptions
===============================================================================
Id User Mode Port
Destination
-------------------------------------------------------------------------------
1 admin stream 49648
192.99.5.0
-------------------------------------------------------------------------------
No. of gRPC Telemetry subscriptions: 1
===============================================================================
A:node-6>show>system>telemetry>grpc# subscription 2
===============================================================================
Telemetry gRPC subscription
===============================================================================
Subscription-id : 2
User : admin
Destination : 192.168.110.252
Port : 54309
===============================================================================
A:node-6>show>system>telemetry>grpc# subscription 1 paths
===============================================================================
Telemetry gRPC subscription
===============================================================================
Subscription id : 1
User : admin
Destination : 192.99.5.0
Port : 49648
Subscription mode : stream
-------------------------------------------------------------------------------
Paths
-------------------------------------------------------------------------------
Path : /state/router[router-instance=*]/interface[interface-
name=*]/ipv4/oper-state
Path mode : on-change
Sample interval : 10000 ms
Finished samples : 1
Deferred samples : 0
Total collection time : 6 ms
Min collection time : 6 ms
Avg collection time : 6 ms
Max collection time : 6 ms
-------------------------------------------------------------------------------
No. of paths : 1
===============================================================================
subscription
Syntax
subscription subscription-name [destinations | paths | scale-paths]
subscription
Context
[Tree] (show>system>telemetry>persistent subscription)
Full Context
show system telemetry persistent subscription
Description
This command displays the active persistent subscriptions.
Parameters
- subscription-name
-
Specifies the subscription name, up to 32 characters.
- destinations
-
Indicates that the output includes all destinations with the respective subscription name.
- paths
-
Indicates that the output includes all paths with the respective subscription name.
- scale-paths
-
Indicates that the output includes all scale paths with the respective subscription name.
Platforms
All
Output
The following output is an example of persistent subscription fields and Show Persistent Subscription Field Descriptions describes the output fields.
Output Example# show system telemetry persistent subscription
===============================================================================
Telemetry persistent subscriptions
===============================================================================
Name Admin Oper
-------------------------------------------------------------------------------
miro Disabled Down
-------------------------------------------------------------------------------
No. of persistent Telemetry subscriptions: 1
===============================================================================
# show system telemetry persistent subscription miro
===============================================================================
Telemetry persistent subscription
===============================================================================
Subscription Name : miro
Administrative State : Disabled
Operational State : Down
Oper Down Reason : TODO
Subscription Id : 0
Description :
Sensor Group : miro
Destination Group : miro
Path Mode : none
Sample Interval : 10000 ms
Encoding : json
===============================================================================
# show system telemetry persistent subscription miro destinations
===============================================================================
Telemetry persistent subscription
===============================================================================
Subscription Name : miro
Administrative State : Disabled
Operational State : Down
Oper Down Reason : TODO
Subscription Id : 0
Description :
Sensor Group : miro
Destination Group : miro
Path Mode : none
Sample Interval : 10000 ms
Encoding : json
-------------------------------------------------------------------------------
Destinations
-------------------------------------------------------------------------------
Destination : 1.1.1.1
Port : 57400
Operational State : Down
Oper Down Reason : TODO
Router Instance :
Establishment Time : 1970/01/01 00:00:00
Retry Count : 0
Operational Qos : be
Notification Count : 0
Total Notification Co*: 0
-------------------------------------------------------------------------------
No. of destinations : 1
* indicates that the corresponding row element may have been truncated.
===============================================================================
# show system telemetry persistent subscription miro paths
===============================================================================
Telemetry persistent subscription
===============================================================================
Subscription Name : miro
Administrative State : Disabled
Operational State : Down
Oper Down Reason : TODO
Subscription Id : 0
Description :
Sensor Group : miro
Destination Group : miro
Path Mode : none
Sample Interval : 10000 ms
Encoding : json
-------------------------------------------------------------------------------
Paths
-------------------------------------------------------------------------------
Path : miro
Finished Samples : 0
Deferred Samples : 0
Total Collection Time : 0 ms
Min Collection Time : 0 ms
Avg Collection Time : 0 ms
Max Collection Time : 0 ms
-------------------------------------------------------------------------------
No. of paths : 1
===============================================================================
Label |
Description |
---|---|
Subscription Name |
Displays the name of the persistent subscription. |
Administrative State |
Enabled — The administrative state of the persistent subscription is enabled. Disabled — The administrative state of the persistent subscription is disabled. |
Operational State |
Up — The operational state of the persistent subscription is up. Down — The operational state of the persistent subscription is down. Transition — The persistent subscription is waiting for the delay-on-boot timer to expire. |
No. of persistent Telemetry subscriptions |
Displays the number of persistent telemetry subscriptions. |
Oper Down Reason |
Displays the reason for the operational down state. |
Subscription Id |
Displays the subscription ID. |
Description |
Displays the description information of the subscription. |
Sensor Group |
Displays the sensor group name. |
Destination Group |
Displays the destination group name. |
Path Mode |
Displays the path mode. |
Sample Interval |
Displays the sample interval. |
Encoding |
json — The encoding method used for telemetry notifications. bytes — The encoding method used for telemetry notifications. |
Destination |
Displays the destination IP address. |
Port |
Displays the destination port. |
Router Instance |
Displays the router instance. |
Establishment Time |
Displays the date and time of the destination establishment. |
Retry Count |
Displays the number of missed TCP keepalive probes before closing a TCP connection. |
Operational Qos |
Displays the QoS marking type. |
Notification Count |
Displays the notification count. |
Total Notification Co* |
Displays the total notification count. |
No. of destinations |
Displays the total number of configured destinations. |
Path |
Displays the path name. |
Finished Samples |
Displays the number of finished samples. |
Deferred Samples |
Displays the number of deferred samples. |
Total Collection Time |
Displays the total collection time. |
Min Collection Time |
Displays the minimum collection time. |
Avg Collection Time |
Displays the average collection time. |
Max Collection Time |
Displays the maximum collection time. |
No. of paths |
Displays the total number of configured paths. |
subscriptions
subscriptions
Syntax
subscriptions
Context
[Tree] (tools>dump>log subscriptions)
Full Context
tools dump log subscriptions
Description
This command displays the list of CLI logs to which each CLI session is currently subscribed.
Platforms
All
Output
The following is an output example.
Output Example===============================================================================
CLI log subscriptions of all CLI sessions
===============================================================================
Session ID : 6
Type : console
User : admin
Login time : 19OCT2017 08:24:14
Remote IP address: 192.168.102.122
Log ID : 1
: 2
: 3
: 4
: 5
...
: 20
-------------------------------------------------------------------------------
Session ID : 25
Type : telnet
User : admin
Login time : 19OCT2017 08:33:16
Remote IP address: 192.168.102.138
Log ID : 1
: 2
===============================================================================
Output Parameters describes the output fields.
Label |
Description |
---|---|
Session ID |
Specifies the session ID. |
Type |
Specifies the type of session (console, telnet, and so on). |
User |
Specifies the name of the user. |
Login time |
Specifies the time the user logged in. |
Remote IP address |
Specifies the originating (client side) IP address of the session. |
Log ID |
Specifies the log ID. |
subscriptions
Syntax
subscriptions
Context
[Tree] (tools>dump>log subscriptions)
Full Context
tools dump log subscriptions
Description
This command displays the list of active subscriptions for this CLI session only.
Platforms
All
Output
The following output is an example of subscriptions information.
Output Example===============================================================================
CLI logs this CLI session is subscribed to
===============================================================================
Log Id
-------------------------------------------------------------------------------
31
72
-------------------------------------------------------------------------------
No. of subscriptions: 2
===============================================================================
Output Parameters describes subscriptions output fields.
Label |
Description |
---|---|
No. of subscriptions |
Specifies the number of active subscriptions. |
summary
summary
Syntax
summary
Context
[Tree] (show>router>dhcp>server summary)
[Tree] (show>router>dhcp6>server summary)
Full Context
show router dhcp local-dhcp-server summary
show router dhcp6 local-dhcp-server summary
Description
This command displays DHCP or DHCP6 server summary information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of DHCP summary information.
Output Example*A:SUB-Dut-A# show router dhcp local-dhcp-server dhcpS2 summary
===============================================================================
DHCP server dhcpS2 router Base
===============================================================================
dhcpS2-POOL2
Admin State : inService
Persistency State : ok
User Data Base : N/A
Use gateway IP address : disabled
Send force-renewals : disabled
-------------------------------------------------------------------------------
Pool name : POOL2
-------------------------------------------------------------------------------
Subnet Free Stable Declined Offered Remove-pending
-------------------------------------------------------------------------------
10.0.0.0/8 16384 0 0 0 0
Totals for pool 16384 0 0 0 0
-------------------------------------------------------------------------------
Totals for server 16384 0 0 0 0
-------------------------------------------------------------------------------
Associations Admin
-------------------------------------------------------------------------------
No associations found
===============================================================================
*A:SUB-Dut-A#
*A:vsim-2# show router 500 dhcp local-dhcp-server "d4" summary
===============================================================================
DHCP server d4 router 500
===============================================================================
Admin State : inService
Operational State : inService
Persistency State : shutdown
User Data Base : N/A
Use gateway IP address : enabled (scope subnet)
Use pool from client : disabled
Send force-renewals : disabled
Creation Origin : manual
Lease Hold Time : 0h0m0s
Lease Hold Time For : N/A
User-ident : mac-circuit-id
Failover Admin State : outOfService
Failover Oper State : shutdown
Failover Persist Key : N/A
Administrative MCLT : 0h10m0s
Operational MCLT : 0h10m0s
Startup wait time : 0h2m0s
Partner down delay : 23h59m59s
Ignore MCLT : disabled
-------------------------------------------------------------------------------
Pool name : v4-1
-------------------------------------------------------------------------------
Failover Admin State : inService
Failover Oper State : normal
Failover Persist Key : N/A
Administrative MCLT : 0h10m0s
Operational MCLT : 0h10m0s
Startup wait time : 0h2m0s
Partner down delay : 23h59m59s
Ignore MCLT : disabled
-------------------------------------------------------------------------------
Subnet Free % Stable Declined Offered Rem-pend Drain
-------------------------------------------------------------------------------
10.20.20.0/24 (L) 10 90% 1 0 0 0 N
(R) N/A 0 N/A N/A N/A N
Totals for pool 10 90% 1 0 0 0
-------------------------------------------------------------------------------
Totals for server 10 90% 1 0 0 0
-------------------------------------------------------------------------------
Interface associations
Interface Admin
-------------------------------------------------------------------------------
l1 Up
-------------------------------------------------------------------------------
Local Address Assignment associations
Group interface Admin
-------------------------------------------------------------------------------
===============================================================================
*A:vsim-2#
summary
Syntax
summary
Context
[Tree] (show>router>dhcp summary)
[Tree] (show>router>dhcp6 summary)
Full Context
show router dhcp summary
show router dhcp6 summary
Description
This command displays the status of the DHCP6 relay and DHCP snooping functions on each interface.
Platforms
All
Output
The following outputs are examples of DHCP and DHCP6 summary information.
Output ExampleA:ALA-48>show>router>dhcp# summary
===================================================================
Interface Name Arp Used/ Info Admin
Populate Provided Option State
-------------------------------------------------------------------
ccaiesif No 0/0 Keep Down
ccanet6 No 0/0 Keep Down
iesBundle No 0/0 Keep Up
spokeSDP-test No 0/0 Keep Down
test No 0/0 Keep Up
test1 No 0/0 Keep Up
test2 No 0/0 Keep Up
testA No 0/0 Keep Up
testB No 0/0 Keep Up
testIES No 0/0 Keep Up
to-web No 0/0 Keep Up
-------------------------------------------------------------------
Interfaces: 11
===================================================================
A:ALA-48>show>router>dhcp#
*A:vsim-2# show router 500 dhcp summary
===============================================================================
DHCP Summary (Service: 500)
===============================================================================
Interface Name Arp Leases Per Interface/ Info Admin
SapId/Sdp Populate Per Sap Limit Option State
-------------------------------------------------------------------------------
g1 No 1/1 Keep Up
sap:1/1/7 1/1
l1 No 0/0 Keep Down
-------------------------------------------------------------------------------
Interfaces: 2
===============================================================================
*A:vsim-2#
DHCP Summary Field Descriptions describes DHCP summary output field descriptions.
Label |
Description |
---|---|
Interface Name |
The name of the router interface |
ARP Populate |
ARP populate is enabled or disabled |
Used/Provided |
The number of used and provided DHCP leases |
Info Option |
Option 82 processing is enabled or disabled on the interface |
Admin State |
The administrative state |
*A:vsim-2# show router 500 dhcp6 summary
===============================================================================
DHCP6 Summary (Service: 500)
===============================================================================
-------------------------------------------------------------------------------
Service Interfaces
-------------------------------------------------------------------------------
Interface Name Nbr Used/Max Relay Admin Oper Relay
SapId Resol. Used/Max Server Admin Oper Server
-------------------------------------------------------------------------------
l1 No 0/0 Down Down
0/8000 Down Down
-------------------------------------------------------------------------------
Interfaces: 1
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Routed CO Interfaces
-------------------------------------------------------------------------------
Interface Name Used Admin (proxy/relay)
SapId
-------------------------------------------------------------------------------
g1 1 Down/Up
sap:1/1/7 1
-------------------------------------------------------------------------------
Interfaces: 1 1
-------------------------------------------------------------------------------
===============================================================================
*A:vsim-2#
*A:vsim-2# show router 500 dhcp6 local-dhcp-server "d6" summary
===============================================================================
DHCP server d6 router 500
===============================================================================
Admin State : inService
Operational State : inService
Persistency State : shutdown
Use Link Address : enabled (scope subnet)
Use pool from client : disabled
Creation Origin : manual
Lease Hold Time : 0h0m0s
Lease Hold Time For : N/A
User-ident : duid
Interface-id-mapping : disabled
Ignore-rapid-commit : disabled
Allow-lease-query : disabled
Failover Admin State : outOfService
Failover Oper State : shutdown
Failover Persist Key : N/A
Administrative MCLT : 0h10m0s
Operational MCLT : 0h10m0s
Startup wait time : 0h2m0s
Partner down delay : 23h59m59s
Ignore MCLT : disabled
-------------------------------------------------------------------------------
Pool name : v6-1
-------------------------------------------------------------------------------
Failover Admin State : inService
Failover Oper State : preNormal
Failover Persist Key : N/A
Time Left : 0h4m16s before state transition
Administrative MCLT : 0h10m0s
Operational MCLT : 0h10m0s
Startup wait time : 0h2m0s
Partner down delay : 23h59m59s
Ignore MCLT : disabled
-------------------------------------------------------------------------------
Prefix
Stable Declined Advert Rem-pend Drain
-------------------------------------------------------------------------------
2001:dead:1::/56
(L) 1 0 0 0 N
2001:dead:2::/56
(R) 0 0 0 0 N
Totals for pool 1 0 0 0
-------------------------------------------------------------------------------
Totals for server 1 0 0 0
-------------------------------------------------------------------------------
Interface associations
Interface Admin
-------------------------------------------------------------------------------
l1 Up
-------------------------------------------------------------------------------
Local Address Assignment associations
Group interface Admin
-------------------------------------------------------------------------------
===============================================================================
*A:vsim-2#
DHCP6 Summary Field Descriptions describes DHCP6 summary output fields.
Label |
Description |
---|---|
Interface Name |
The name of the router interface |
ARP Populate |
ARP populate is enabled or disabled |
Used/Provided |
The number of used and provided DHCP leases |
Info Option |
Option 82 processing enabled or disabled on the interface |
Admin State |
The administrative state |
summary
Syntax
summary [interface interface-name | saps]
Context
[Tree] (show>service>id>dhcp summary)
Full Context
show service id dhcp summary
Description
This command displays DHCP configuration summary information.
Parameters
- interface-name
-
Displays information for the specified IP interface.
- saps
-
Displays SAPs per interface.
Platforms
All
Output
The following output is an example of DHCP summary information, and Show Service-ID DHCP Summary Field Descriptions describes the output fields.
Output ExampleA:ALA-49# show service id 1 dhcp summary
===============================================================================
DHCP Summary, service 1
===============================================================================
Interface Name Arp Used/ Info Admin
SapId/Sdp Populate Provided Option State
-------------------------------------------------------------------------------
SpokeSDP No 0/0 Keep Up
sdp:spoke-3:4 0/0
test No 0/0 Keep Up
sap:1/1/4:50/5 0/0
to-ce1 No 0/0 Keep Up
sap:1/1/10:1 0/0
-------------------------------------------------------------------------------
Interfaces: 3
===============================================================================
A:ALA-49#
Label |
Description |
---|---|
Sap/Sdp |
The configuration identification, expressed by a string containing "card/mda/port/:logical-id”. |
Snoop |
Yes — The packets received from the DHCP clients were snooped. No — The packets received from the DHCP clients were not snooped. |
Used/Provided |
Used — The number of lease-states that are currently in use on a specific interface, that is, the number of clients on that interface got an IP address by DHCP. This value is always less than or equal to the 'Provided’ field. Provided — The lease-populate value that is configured for a specific interface. |
Arp Reply Agent |
Displays whether or not there is proper handling of received ARP requests from subscribers. |
Info Option |
Keep — The existing information is kept on the packet and the router does not add any additional information. Replace — On ingress, the existing information-option is replaced with the information-option from the router. Drop —The packet is dropped and an error is logged. |
Admin State |
Indicates the administrative state. |
summary
Syntax
summary
Context
[Tree] (show>service>id>ppp summary)
Full Context
show service id ppp summary
Description
This command displays PPP summary information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
summary
Syntax
summary
Context
[Tree] (show>subscr-mgmt>gtp summary)
Full Context
show subscriber-mgmt gtp summary
Description
This command displays a GTP system summary of information.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of GTP summary information.
Output ExampleNode# show subscriber-mgmt gtp summary
===============================================================================
GTP system summary
===============================================================================
Actual number of MME : 1
Actual number of ENODE-B : 1
Actual number of S11 Sessions : 1
Actual number of Mobile Gateways : 0
Actual number of Uplinks : 0
Actual number of Uplinks in Hold : 0
===============================================================================
summary
Syntax
summary
Context
[Tree] (show>service>id>pppoe summary)
Full Context
show service id pppoe summary
Description
This command displays PPPoE summary information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
summary
Syntax
summary
Context
[Tree] (show>service>id>ipoe summary)
Full Context
show service id ipoe summary
Description
This command displays a summary of IPoE information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
summary
Syntax
summary
Context
[Tree] (show>service>dynsvc summary)
Full Context
show service dynamic-services summary
Description
This command displays the global configuration summary for dynamic services:
-
Service range
-
Timers
This command is not available in the MD-CLI.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of dynamic service summary information.
Output Example# show service dynamic-services summary
===============================================================================
Dynamic Services Summary
===============================================================================
range start : 100000
range end : 200001
setup timeout Access Accept : 30
===============================================================================
Dynamic Services Summary Field Descriptions describes Dynamic Services summary fields.
Output field |
Description |
---|---|
range start |
The start service ID to define the service range for dynamic services. |
range end |
The start and end service ID to define the service range for dynamic services. |
setup timeout Access Accept |
The timeout, in seconds, after which a script is canceled for setup actions received via RADIUS Access-Accept messages. |
summary
Syntax
summary
Context
[Tree] (show>service>id>slaac summary)
Full Context
show service id slaac summary
Description
This command displays a summary of all SLAAC hosts.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
summary
Syntax
summary [sap sap-id]
Context
[Tree] (show>service>id>host-connectivity-verify summary)
Full Context
show service id host-connectivity-verify summary
Description
This command displays a host connectivity verification summary.
Parameters
- sap-id
-
Specifies the SAP ID to show statistics for.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
summary
Syntax
summary [all]
summary [family family] [ group name]
Context
[Tree] (show>router>bgp summary)
Full Context
show router bgp summary
Description
This command displays a summary of BGP neighbor information.
If confederations are not configured, that information is not displayed in the command output.
The "State” field displays the global BGP operational state. The valid values are:
-
Up — BGP global process is configured and running.
-
Down — BGP global process is administratively shutdown and not running.
-
Disabled — BGP global process is operationally disabled. The process must be restarted by the operator. For example, if a BGP peer is operationally disabled, the state in the summary table shows the state 'Disabled’.
Parameters
- all
-
Displays BGP peers in all instances.
- family
-
Specifies the type of routing information to be distributed by the BGP instance.
- name
-
Specifies the group name up to 32 characters.
Platforms
All
Output
The following output is an example of BGP summary information, and Show BGP Summary Field Descriptions describes the output fields.
Output ExampleA:Dut-B>config>router>bgp# show router bgp summary
===============================================================================
BGP Router ID:1.0.0.2 AS:1 Local AS:1
===============================================================================
BGP Admin State : Up BGP Oper State : Up
Total Peer Groups : 1 Total Peers : 1
Total VPN Peer Groups : 0 Total VPN Peers : 0
Current Internal Groups : 1 Max Internal Groups : 1
Total BGP Paths : 19 Total Path Memory : 6840
*A:ALA-12# show router 3 bgp summary
===============================================================================
BGP Router ID : 10.0.0.14 AS : 65206 Local AS : 65206
===============================================================================
BGP Admin State : Up BGP Oper State : Up
Confederation AS : 40000
Member Confederations : 65205 65206 65207 65208
Number of Peer Groups : 2 Number of Peers : 7
Total BGP Active Routes : 86689 Total BGP Routes : 116999
Total BGP Paths : 35860 Total Path Memory : 2749476
Total Supressed Routes : 0 Total History Routes : 0
Total Decayed Routes : 0
===============================================================================
BGP Summary
===============================================================================
Neighbor AS PktRcvd PktSent InQ OutQ Up/Down State|Recv/Actv/Sent
-------------------------------------------------------------------------------
10.0.0.1 65206 5 21849 0 0 00h01m29s 32/0/86683
10.0.0.12 65206 0 0 0 0 00h01m29s Active
10.0.0.13 65206 5 10545 0 50 00h01m29s 6/0/86683
10.0.0.15 65205 0 0 0 0 00h01m29s Active
10.0.0.16 65206 5 9636 0 50 00h01m29s 6/0/86683
10.0.27.1 2 0 0 0 0 00h01m29s Active
10.0.28.1 60203 22512 15 0 0 00h01m29s 116955/86689/9
===============================================================================
*A:ALA-12#
Label |
Description |
---|---|
BGP Router ID |
The local BGP router ID |
AS |
The configured autonomous system number |
Local AS |
The configured local AS setting, if not configured it is the same as the system AS |
BGP Admin State |
Down — BGP is administratively disabled Up — BGP is administratively enabled |
BGP Oper State |
Down — BGP is operationally disabled Up — BGP is operationally enabled |
Confederation AS |
The configured confederation AS |
Current Internal Groups |
The current number of internal BGP peer groups. BGP peers are grouped within the BGP software to optimize the building of UPDATE messages towards peers with a similar configuration. An internal group is not the same as a configured BGP peer group. |
Max Internal Groups |
The maximum number of internal BGP peer groups that existed at any point since the last restart of BGP. BGP peers are grouped within the BGP software to optimize the building of UPDATE messages towards peers with a similar configuration. An internal group is not the same as a configured BGP peer group. |
Member Confederations |
The configured members of the BGP confederation |
Number of Peer Groups |
The total number of configured BGP peer groups |
Number of Peers |
The total number of configured BGP peers |
Total BGP Active Routes |
The total number of BGP routes used in the forwarding table |
Total BGP Routes |
The total number of BGP routes learned from BGP peers |
Total BGP Paths |
The total number of unique sets of BGP path attributes learned from BGP peers |
Total Path Memory |
Total amount of memory used to store the path attributes |
Total Suppressed Routes |
Total number of suppressed routes due to route damping |
Total History Routes |
Total number of routes with history due to route damping |
Total Decayed Routes |
Total number of decayed routes due to route damping |
Neighbor |
BGP neighbor address |
AS (Neighbor) |
BGP neighbor autonomous system number |
PktRcvd |
Total number of packets received from the BGP neighbor |
PktSent |
Total number of packets sent to the BGP neighbor |
InQ |
The number of BGP messages to be processed |
OutQ |
The number of BGP messages to be transmitted |
Up/Down |
The amount of time that the BGP neighbor has either been established or not established depending on its current state |
State|Recv/Actv/Sent |
The BGP neighbor’s current state (if not established) or the number of received routes, active routes and sent routes (if established) |
summary
Syntax
summary [session ip-addr[label-space]] [ ipv4 | ipv6]
Context
[Tree] (show>router>ldp>bindings summary)
Full Context
show router ldp bindings summary
Description
This command displays a summary of LDP bindings.
Parameters
- session ip-addr[label-space]
-
Specifies the IP address and label space identifier.
- ipv4
-
Displays IPv4 summary bindings information.
- ipv6
-
Displays IPv6 summary bindings information.
Platforms
All
summary
Syntax
summary
Context
[Tree] (show>router>mpls-labels summary)
Full Context
show router mpls-labels summary
Description
This command displays the MPLS label summary.
Platforms
All
Output
The following output is an example of MPLS label summary information.
MPLS Label Summary Output Fields describes MPLS label summary output fields.
Output Example*A:cses-V23>show>router>mpls-labels># show router mpls-labels summary
===============================================================================
Mpls-Labels Summary
===============================================================================
Static Label Range : 18400
Bgp Labels Hold Timer : 30
Segment Routing Start Label : 0
Segment Routing End Label : 0
Reserved Label Block Name :
test reserved-label
===============================================================================
Label |
Description |
---|---|
Static Label Range |
Displays the static label range. |
Bgp Labels Hold Timer |
Displays the BGP labels hold timer. |
Segment Routing Start Label |
Displays the segment routing start label. |
Segment Routing End Label |
Displays the segment routing end label. |
Reserved Label Block Name |
Displays the reserved label block name. |
summary
Syntax
summary
Context
[Tree] (show>app-assure>group>http-enrich summary)
Full Context
show application-assurance group http-enrich summary
Description
This command displays summarized HTTP enrichment information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
summary
Syntax
summary
Context
[Tree] (show>app-assure>group>policy summary)
Full Context
show application-assurance group policy summary
Description
This command displays application-assurance policy summary information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
summary
Syntax
summary
Context
[Tree] (show>app-assure>group>aa-sub summary)
Full Context
show application-assurance group aa-sub summary
Description
This command displays a summary of statistics for a specific aa-sub.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of the summary information.
Output ExampleA:ALU>show>app-assure>group>aa-sub# summary
===============================================================================
Application-Assurance Subscriber Summary
===============================================================================
AA-Subscriber : TestSubscriberName
ISA assigned : 3/2
App-Profile : Power_Profile
App-Profile divert : Yes
Sub-quarantined : No
Capacity cost : 1
-------------------------------------------------------------------------------
Traffic Octets Packets Flows
-------------------------------------------------------------------------------
Admitted from subscriber: 7092548 52935 2843
Denied from subscriber: 51160 617 374
Active flows from subscriber: 12
Admitted to subscriber: 73705675 73538 1453
Denied to subscriber: 0 0 0
Active flows to subscriber: 12
Total flow duration: 12750 seconds
Terminated flows: 4646
Short Duration flows: 4516
Medium Duration flows: 130
Long Duration flows: 0
-------------------------------------------------------------------------------
Top App-Groups Octets Packets Flows
-------------------------------------------------------------------------------
MultiMedia 29060053 29961 138
Tunneling 19659289 33535 164
Web 14856331 19829 932
===============================================================================
A:ALU>show>app-assure>group>aa-sub#
summary
Syntax
summary
Context
[Tree] (tools>dump>app-assure>group summary)
Full Context
tools dump application-assurance group summary
Description
This command displays subscriber summary information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
summary
Syntax
summary
Context
[Tree] (show>router>firewall summary)
Full Context
show router firewall summary
Description
This command displays a simple overview of all firewall configurations specific to the routing instance.
Platforms
7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of summary firewall information.
Output ExampleNode# show router 4 firewall summary
===============================================================================
Firewall policies
===============================================================================
Policy : firewall_dhcp6_4
-------------------------------------------------------------------------------
Domain : domain_dhcp6_4
ISA group : 1
Administrative state : in-service
Policy : firewall_slaac_4
-------------------------------------------------------------------------------
Domain : domain_slaac_4
ISA group : 1
Administrative state : in-service
-------------------------------------------------------------------------------
No. of policies: 2
===============================================================================
summary
Syntax
summary
Context
[Tree] (show>router>nat summary)
Full Context
show router nat summary
Description
This command displays the NAT information summary.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of this command.
Output Example*A:SR12_PPPOE>show>router>nat# show router Base nat summary
===============================================================================
NAT pools
===============================================================================
Pool NAT-group Type Admin-state
-------------------------------------------------------------------------------
privpool 3 largeScale inService
pubpool 1 largeScale inService
-------------------------------------------------------------------------------
No. of pools: 2
===============================================================================
A:SR12_PPPOE#
The following is an output example showing NAT import policy information.
*A:Dut-C>config>service>vprn>nat>inside# /show router 101 nat summary
===============================================================================
ISA NAT group redundancy : active-standby
===============================================================================
===============================================================================
Subscriber identification
===============================================================================
Admin state : outOfService
Attribute vendor : nokia
Attribute type : alc-sub-string
Description : (Not Specified)
Drop unidentified traffic : false
Radius proxy server router : (Not Specified)
Radius proxy server name : (Not Specified)
Last management change : 05/11/2021 11:09:25
===============================================================================
===============================================================================
NAT Redundancy
===============================================================================
Peer : (Not Specified)
IPv6 peer : (Not Specified)
Steering route : (Not Specified)
===============================================================================
===============================================================================
NAT policies
===============================================================================
Policy : n44Pool1-1
-------------------------------------------------------------------------------
Inside router : vprn101
Outside router : vprn601
Pool : n44Pool1
Type : default
Active : true
-------------------------------------------------------------------------------
No. of policies: 1
===============================================================================
===============================================================================
NAT-Import policies
===============================================================================
Policy 1 : policystatment1
Policy 2 : bgpNat3
Policy 3 : (Not Specified)
Policy 4 : (Not Specified)
Policy 5 : (Not Specified)
===============================================================================
===============================================================================
Destination NAT
===============================================================================
Inside source prefix list : (Not Specified)
Outside route limit : 32768
Outside routes : 0
===============================================================================
===============================================================================
Large Scale NAT destination prefixes
===============================================================================
Destination prefix Nat policy
-------------------------------------------------------------------------------
200.0.0.0/16 n44Pool1-1
===============================================================================
*A:Dut-C>config>service>vprn>nat>inside#
summary
Syntax
summary
Context
[Tree] (show>grp-encryp summary)
Full Context
show group-encryption summary
Description
This command shows NGE summary information.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of NGE summary information, and Show Group Encryption Summary Output Fields describes the fields.
Output Exampledomain1>show>grp-encryp# summary
============================
Group Encryption
============================
Encryption Label : 34
============================
=======================================================
Encryption Keygroup
=======================================================
Id Name Auth Algo Encr Algo Active OutSA
-------------------------------------------------------
2 KG1_secure sha256 aes128 6
4 sha256 aes128 0
-------------------------------------------------------
No. of Encryption Keygroup: 2
=======================================================
domain1>show>grp-encryp#
Label |
Description |
---|---|
Group Encryption |
|
Encryption Label |
The unique network-wide group encryption label |
Encryption Keygroup |
|
Id |
The key group identifier value |
Name |
The key group name |
Auth Algo |
The authentication algorithm used by the key group |
Encr Algo |
The encryption algorithm used by the key group |
Active OutSA |
The active outbound SA for the key group |
No. of Encryption Keygroup |
The number of encryption key groups currently configured on the node |
summary
Syntax
summary
Context
[Tree] (show>router>seg-rt>sr-policies summary)
Full Context
show router segment-routing sr-policies summary
Description
This command displays summary information about all policies: BGP, static local, and static non-local.
Platforms
All
Output
The following output is an example of policies summary information.
Output Example*A:Dut-A>config>router# show router segment-routing sr-policies summary
===============================================================================
SR-Policies Summary
===============================================================================
Admin Status : Up
Ingress Stats : N/A Egress Stats : N/A
Resv Label Blk Name:
TTM Preference : 14 BSID Allocated : 0
Static Local Policies : 2 Active Static Lcl Pol : 2
Static Non Local Pol : 0
BGP Policies : 0 Active BGP Policies : 0
===============================================================================
summary
Syntax
summary
Context
[Tree] (show>subscr-mgmt>pfcp summary)
Full Context
show subscriber-mgmt pfcp summary
Description
This command displays PFCP session and association counters.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of PFCP summary information.
Output ExampleA:BNG-UPF# show subscriber-mgmt pfcp summary
===============================================================================
PFCP system summary
===============================================================================
Actual number of associations : 1
Actual number of PFCP sessions : 2
Actual number of PFCP sessions in setup : 0
Actual number of default tunnels : 1
Actual number of PPP sessions : 1
Actual number of IPOE sessions : 0
===============================================================================
summary
Syntax
summary
Context
[Tree] (show>router>srv6 summary)
Full Context
show router segment-routing-v6 summary
Description
This command displays the summary SRv6 status.
Platforms
7450 ESS, 7750 SR, 7750 SR-s, 7950 XRS, VSR
summary
Syntax
summary
Context
[Tree] (show>li>x-interfaces summary)
Full Context
show li x-interfaces summary
Description
This command displays a summary of the status of the X1, X2, and X3 interfaces.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
summary
Syntax
summary
Context
[Tree] (tools>dump>system>cpm-http-redirect summary)
Full Context
tools dump system cpm-http-redirect summary
Description
This command displays the summary of the cpm-http-redirect optimized-mode information for the total number of hosts and connections currently in use. This output can also be used to compare the current system utilization with the maximum system scale.
Platforms
All
Output
The following output is an example of the summary information.
Output ExampleA# tools dump system cpm-http-redirect summary
===============================================================================
CPM HTTP Redirect summary
===============================================================================
Actual number of hosts : 0
Actual number of connections : 0
Number of hosts created in the last second : 0
Number of connections created in the last second : 0
===============================================================================
summary
Syntax
summary [family] [egress-if port-id]
summary [family] [egress-lsp tunnel-id]
summary [egress-nh ip-address] [family]
Context
[Tree] (show>router>ldp>bindings>active summary)
Full Context
show router ldp bindings active summary
Description
This command displays a summary of the LDP active bindings.
Parameters
- ip-address
-
Specifies the IPv4 or IPv6 address.
- family
-
Specifies the address family.
- port-id
-
Specifies the port ID.
- tunnel-id
-
Specifies the tunnel ID.
Platforms
All
summary-address
summary-address
Syntax
summary-address [ip-address [/prefix-length]]
Context
[Tree] (show>router>isis summary-address)
Full Context
show router isis summary-address
Description
This command displays IS-IS summary addresses information.
Platforms
All
Output
Router IS-IS Summary Address Output
IS-IS Summary Address Output Fields describes the IS-IS summary address output fields.
Label |
Description |
---|---|
Address |
The IP address. |
Level |
Specifies the IS-IS level from which the prefix should be summarized. |
A:ALA-48# show router isis summary-address
===============================================================================
Rtr Base ISIS Instance 0 Summary Address
===============================================================================
Address Level
-------------------------------------------------------------------------------
1.0.0.0/8 L1
2.1.0.0/24 L1L2
3.1.2.3/32 L2
-------------------------------------------------------------------------------
Summary Addresses : 3
===============================================================================
A:ALA-48#
svlan-statistics
svlan-statistics
Syntax
svlan-statistics port port-id all-svlans
svlan-statistics port port-id svlan tag
Context
[Tree] (show>subscr-mgmt svlan-statistics)
Full Context
show subscriber-mgmt svlan-statistics
Description
This command displays S-VLAN statistics.
Parameters
- port-id
-
Specifies the physical port ID in the slot/mda/port format of the S-VLAN.
- all-svlans
-
Displays statistics for all S-VLANs on the port.
- svlan
-
Displays information about the S-VLAN.
- tag
-
Specifies a valid S-VLAN identifier.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of S-VLAN statistics information.
The collected statistics per outer VLAN tag, including the number of subscriber hosts is captured in the output.�
Output Example*A:Dut-C# show subscriber-mgmt svlan-statistics port 1/1/2 all-svlans
===============================================================================
Subscriber VLAN statistics for port 1/1/2 vlan 51
===============================================================================
Ingress Egress
-------------------------------------------------------------------------------
IP packets 5 5
Bytes in IP packets 670 670
Last cleared 12/18/2020 10:03:48
-------------------------------------------------------------------------------
Number of active subscriber hosts : 1
===============================================================================
===============================================================================
Subscriber VLAN statistics for port 1/1/2 vlan 113
===============================================================================
Ingress Egress
-------------------------------------------------------------------------------
IP packets 10 10
Bytes in IP packets 1320 1320
Last cleared 12/18/2020 10:03:48
-------------------------------------------------------------------------------
Number of active subscriber hosts : 2
===============================================================================
*A:Dut-C#
This counter counts subscriber hosts (represented as individual IP addresses) and not sessions. This is shown in the output of the following commands where there is only one session but two subscriber hosts counted in the VLAN statistics.
*A:Dut-C# show service active-subscribers
===============================================================================
Active Subscribers
===============================================================================
-------------------------------------------------------------------------------
Subscriber test-1
(sub_profile)
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
(1) SLA Profile Instance sap:1/1/5:4 - sla:sla_profile
-------------------------------------------------------------------------------
IP Address
MAC Address Session Origin Svc Fwd
-------------------------------------------------------------------------------
10.2.3.41
00:00:00:00:00:04 IPoE DHCP 10 Y
90:64:1:2::/64
00:00:00:00:00:04 IPoE SLAAC 10 Y
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Number of active subscribers : 1
===============================================================================
*A:Dut-C#
*A:Dut-C# show subscriber-mgmt svlan-statistics port 1/1/5 all-svlans
===============================================================================
Subscriber VLAN statistics for port 1/1/5 vlan 4
===============================================================================
Ingress Egress
-------------------------------------------------------------------------------
IP packets 0 0
Bytes in IP packets 0 0
-------------------------------------------------------------------------------
Number of active subscriber hosts : 2
===============================================================================
*A:Dut-C#
svlan-statistics
Syntax
svlan-statistics port port-id all-svlans
svlan-statistics port port-id svlan tag
Context
[Tree] (clear>subscr-mgmt svlan-statistics)
Full Context
clear subscriber-mgmt svlan-statistics
Description
This command clears Subscriber-VLAN statistics.
Parameters
- port-id
-
Specifies the physical port ID in the slot/mda/port format of the S-VLAN.
- all-svlans
-
Clears statistics for all S-VLANs on the port.
- svlan
-
Clears information associated with the S-VLAN.
- tag
-
Specifies a valid S-VLAN identifier.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
switch-fabric
switch-fabric
Syntax
switch-fabric [exclude-sfm sfm-list]
switch-fabric high-bandwidth-multicast
switch-fabric failure-recovery
Context
[Tree] (show>system switch-fabric)
Full Context
show system switch-fabric
Description
This command displays switch fabric information. When an MDA is not provisioned in an XCM, no information is displayed relating to that MDA. To display the forwarding capacity and multicast planes corresponding to that MDA, regardless of whether an XMA is equipped, an mda-type must be provisioned for that MDA.
Parameters
- sfm-list
-
Specifies the SFMs to exclude from the displayed switch fabric information, in the format of a comma separated list of SFM numbers from 1 to 16, depending on the platform.
- high-bandwidth-multicast
-
Specifies that MDA information about the switch-fabric plane’s high bandwidth multicast traffic tap allocation is displayed.
- failure-recovery
-
Specifies to display information about the automatic switch fabric recovery process. The SFMs are listed in numerical order and are only shown when the recovery process is in progress or it has completed.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-e, 7750 SR-1s, 7750 SR-2s, 7750 SR-7s, 7750 SR-14s, 7950 XRS
Output
The following outputs are examples of switch fabric information, and the tables describe the output fields.
-
Output Example show system switch-fabric; Switch Fabric Output Field Descriptions
-
Output Example show system switch-fabric exclude-sfm; Switch Fabric Output Field Descriptions
-
Output Example show system switch-fabric high-bandwidth-multicast; Switch Fabric High Bandwidth Multicast Output Field Descriptions
-
Output Example show system switch-fabric failure-recovery (7750 SR); Show Automatic Switch Fabric Recovery Information Fields
*A:DUT-A# show system switch-fabric
===============================================================================
Switch Fabric
===============================================================================
Slot/FP Min. Forwarding Capacity Max. Forwarding Capacity
-------------------------------------------------------------------------------
1/1 100% 100%
1/2 100% 100%
1/5 100% 100%
1/6 100% 100%
3/1 100% 100%
3/5 100% 100%
3/6 100% 100%
5/1 100% 100%
5/2 100% 100%
5/3 100% 100%
5/5 100% 100%
5/6 100% 100%
5/7 100% 100%
5/8 100% 100%
A 100% 100%
B 100% 100%
-------------------------------------------------------------------------------
sfm-loss-threshold: 2
===============================================================================
Switch Fabric Output Field Descriptions describes the switch fabric output fields.
Label |
Description |
---|---|
Slot/FP |
Displays either the FP (uniquely identified by an IOM number and FP number) or a CPM letter. |
Min. Forwarding Capacity |
Displays the minimum forwarding capacity of the slot and XMA/MDA as a percentage. |
Max. Forwarding Capacity |
Displays the maximum forwarding capacity of the slot and XMA/MDA as a percentage. |
Sfm-loss-threshold |
Displays the number of SFMs that are permitted to fail prior to SFM overload. Supported on SR-7s and SR-14s platforms only. |
*B:DUT-A# show system switch-fabric exclude-sfm 1,2,3
===============================================================================
Switch Fabric
===============================================================================
Slot/FP Min. Forwarding Capacity Max. Forwarding Capacity
-------------------------------------------------------------------------------
1/1 69% 71%
1/2 69% 71%
1/5 100% 100%
1/6 100% 100%
3/1 100% 100%
3/5 69% 69%
3/6 69% 69%
5/1 69% 71%
5/2 69% 71%
5/3 69% 71%
5/5 69% 71%
5/6 69% 71%
5/7 69% 71%
5/8 69% 71%
A 100% 100%
B 100% 100%
-------------------------------------------------------------------------------
sfm-loss-threshold: 2
===============================================================================
Output Example show system switch-fabric
high-bandwidth-multicast
*A:PE-1# show system switch-fabric high-bandwidth-multicast
===============================================================================
Switch Fabric
===============================================================================
Cap: Planes:
Slot/FP Min Max Hbm Grp Hi | Lo
-------------------------------------------------------------------------------
2/1 100% 100% No 0 1 0 2 3 4 5 6 7 8 9 10 11 12 13 14 | 15
5/1 100% 100% No 0 17 16 18 19 20 21 22 23 24 25 26 27 28 29 30 | 31
A 100% 100% No 0 40 | 40
B 100% 100% No 0 24 | 24
===============================================================================
*A:PE-1#
Switch Fabric High Bandwidth Multicast Output Field Descriptions describes the switch fabric high-bandwidth multicast output fields.
Label |
Description |
---|---|
Slot/FP |
Displays either the FP (uniquely identified by an IOM number and FP number) or a CPM letter. |
Cap Min |
Displays the minimum forwarding capacity of the slot and XMA/MDA as a percentage. |
Cap Max |
Displays the maximum forwarding capacity of the slot and XMA/MDA as a percentage. |
Hbm |
Displays high-bandwidth multicast traffic information, which can be used to avoid overlapping planes on FPs that have a lot of multicast ingress traffic. |
Grp |
Displays high-bandwidth multicast groups for each FP. |
Planes Hi | Lo |
Displays plane information. When 2 FPs are in a different group, no plane overlap occurs. |
A:Dut-B# show system switch-fabric failure-recovery
===============================================================================
Automatic Switch Fabric Failure Recovery
===============================================================================
Admin state : enabled
Oper state : recoveryInProgress
-------------------------------------------------------------------------------
SFM Slot State Time
-------------------------------------------------------------------------------
1 pending 02/11/2021 21:05:45
2 inProgress 02/11/2021 21:05:45
===============================================================================
A:Dut-B#
Show Automatic Switch Fabric Recovery Information Fields describes the automatic switch fabric recovery process output fields.
Label |
Description |
---|---|
Admin State |
Displays the administrative state, enabled or disabled. |
Oper State |
Displays the current operational state:
|
SFM Slot |
Displays the fabric slot within a chassis in the system. |
State |
Displays the stage of the automatic switch fabric recovery process. |
Time |
Displays the date and time of the stage. |
switch-fabric
Syntax
switch-fabric
Context
[Tree] (tools>perform>system switch-fabric)
Full Context
tools perform system switch-fabric
Description
This command performs switch fabric operations.
Platforms
7450 ESS, 7750 SR-7, 7750 SR-12e, 7950 XRS
switch-path
switch-path
Syntax
switch-path [lsp lsp-name] [path path-name]
Context
[Tree] (tools>perform>router>mpls switch-path)
Full Context
tools perform router mpls switch-path
Description
Use this command to move from a standby (or an active secondary) to another standby of the same priority. If a new standby path with a higher priority or a primary path comes up after the tools perform command is executed, the path re-evaluation command runs and the path is moved to the path specified by the outcome of the re-evaluation.
Parameters
- lsp-name
-
Specifies an existing LSP name, up to 64 characters in length.
- path-name
-
Specifies the path name to which to move the specified LSP.
Platforms
All
sync
sync
Syntax
sync [peer ip-address]
sync peer ip-address detail
sync [peer ip-address] statistics
Context
[Tree] (show>redundancy>multi-chassis sync)
Full Context
show redundancy multi-chassis sync
Description
This command displays synchronization information.
Parameters
- ip-address
-
Shows peer information about the specified IP address.
- detail
-
Displays detailed peer information.
- statistics
-
Displays peer statistics.
Platforms
All
Output
See the following sections for output example:
The following output is an example of multi-chassis sync information, and Redundancy Multi-chassis Sync Field Descriptions describes the output fields.
Multi-Chassis Sync Output Example*A:subscr_mgt_2# show redundancy multi-chassis sync
===============================================================================
Multi-chassis Peer Table
===============================================================================
Peer
-------------------------------------------------------------------------------
Peer IP Address : 10.10.10.20
Description : Mc-Lag peer 10.10.10.20
Authentication : Disabled
Source IP Address : 0.0.0.0
Admin State : Enabled
-------------------------------------------------------------------------------
Sync-status
-------------------------------------------------------------------------------
Client Applications : SUBMGMT
Sync Admin State : Up
Sync Oper State : Up
DB Sync State : inSync
Num Entries : 1
Lcl Deleted Entries : 0
Alarm Entries : 0
Rem Num Entries : 1
Rem Lcl Deleted Entries : 0
Rem Alarm Entries : 0
===============================================================================
A:subscr_mgt_2#
Label |
Description |
---|---|
Peer IP Address |
Displays the multi-chassis redundancy peer. |
Description |
The text string describing the peer. |
Authentication |
If configured, displays the authentication key used between this node and the multi-chassis peer. |
Source IP Address |
Displays the source address used to communicate with the multi-chassis peer. |
Admin State |
Displays the administrative state of the peer. |
Client Applications |
Displays the list of client applications synchronized between SRs. |
Sync Admin State |
Displays the administrative state of the synchronization. |
Sync Oper State |
Displays the operation state of the synchronization. |
DB Sync State |
Displays the database state of the synchronization. |
Num Entries |
Displays the number of entries on local router. |
Lcl Deleted Entries |
Displays the number of deleted entries made at the local router. |
Alarm Entries |
Displays the alarm entries on the local router. |
Rem Num Entries |
Displays the number of entries on the remote router. |
Rem Lcl Deleted Entries |
Displays the number of locally deleting entries made by the remote router. |
Rem Alarm Entries |
Displays alarm entries on the remote router. |
The following output is an example of multi-chassis sync peer information, and Redundancy Multi-chassis Sync Peer Field Descriptions describes the output fields.
Redundancy Multi-Chassis Sync Peer Output Example*A:subscr_mgt_2# show redundancy multi-chassis sync peer 10.10.10.20
===============================================================================
Multi-chassis Peer Table
===============================================================================
Peer
-------------------------------------------------------------------------------
Peer IP Address : 10.10.10.20
Description : Mc-Lag peer 10.10.10.20
Authentication : Disabled
Source IP Address : 0.0.0.0
Admin State : Enabled
-------------------------------------------------------------------------------
Sync-status
-------------------------------------------------------------------------------
Client Applications : SUBMGMT
Sync Admin State : Up
Sync Oper State : Up
DB Sync State : inSync
Num Entries : 1
Lcl Deleted Entries : 0
Alarm Entries : 0
Rem Num Entries : 1
Rem Lcl Deleted Entries : 0
Rem Alarm Entries : 0
===============================================================================
MCS Application Stats
===============================================================================
Application : igmp
Num Entries : 0
Lcl Deleted Entries : 0
Alarm Entries : 0
-------------------------------------------------------------------------------
Rem Num Entries : 0
Rem Lcl Deleted Entries : 0
Rem Alarm Entries : 0
-------------------------------------------------------------------------------
Application : igmpSnooping
Num Entries : 0
Lcl Deleted Entries : 0
Alarm Entries : 0
-------------------------------------------------------------------------------
Rem Num Entries : 0
Rem Lcl Deleted Entries : 0
Rem Alarm Entries : 0
-------------------------------------------------------------------------------
Application : subMgmt
Num Entries : 1
Lcl Deleted Entries : 0
Alarm Entries : 0
-------------------------------------------------------------------------------
Rem Num Entries : 1
Rem Lcl Deleted Entries : 0
Rem Alarm Entries : 0
-------------------------------------------------------------------------------
Application : srrp
Num Entries : 0
Lcl Deleted Entries : 0
Alarm Entries : 0
-------------------------------------------------------------------------------
Rem Num Entries : 0
Rem Lcl Deleted Entries : 0
Rem Alarm Entries : 0
===============================================================================
*A:subscr_mgt_2#
Label |
Description |
---|---|
Peer IP Address |
Displays the multi-chassis redundancy peer. |
Description |
The text string describing the peer. |
Authentication |
If configured, displays the authentication key used between this node and the multi-chassis peer. |
Source IP Address |
Displays the source address used to communicate with the multi-chassis peer. |
Admin State |
Displays the administrative state of the peer. |
Client Applications |
Displays the list of client applications synchronized between SRs. |
Sync Admin State |
Displays the administrative state of the synchronization. |
Sync Oper State |
Displays the operation state of the synchronization. |
DB Sync State |
Displays the database state of the synchronization. |
Num Entries |
Displays the number of entries on local router. |
Lcl Deleted Entries |
Displays the number of deleted entries made at the local router. |
Alarm Entries |
Displays the alarm entries on the local router. |
Rem Num Entries |
Displays the number of entries on the remote router. |
Rem Lcl Deleted Entries |
Displays the number of locally deleting entries made by the remote router. |
Rem Alarm Entries |
Displays alarm entries on the remote router. |
The following output is an example of multi-chassis sync detail information, and Redundancy Multi-chassis Sync Peer Detail Field Descriptions describes the output fields.
Output Example: Redundancy Multi-Chassis Sync Peer Detail*A:subscr_mgt_2# show redundancy multi-chassis sync peer 10.10.10.20 detail
===============================================================================
Multi-chassis Peer Table
===============================================================================
Peer
-------------------------------------------------------------------------------
Peer IP Address : 10.10.10.20
Description : Mc-Lag peer 10.10.10.20
Authentication : Disabled
Source IP Address : 0.0.0.0
Admin State : Enabled
-------------------------------------------------------------------------------
Sync-status
-------------------------------------------------------------------------------
Client Applications : SUBMGMT
Sync Admin State : Up
Sync Oper State : Up
DB Sync State : inSync
Num Entries : 1
Lcl Deleted Entries : 0
Alarm Entries : 0
Rem Num Entries : 1
Rem Lcl Deleted Entries : 0
Rem Alarm Entries : 0
===============================================================================
MCS Application Stats
===============================================================================
Application : igmp
Num Entries : 0
Lcl Deleted Entries : 0
Alarm Entries : 0
-------------------------------------------------------------------------------
Rem Num Entries : 0
Rem Lcl Deleted Entries : 0
Rem Alarm Entries : 0
-------------------------------------------------------------------------------
Application : igmpSnooping
Num Entries : 0
Lcl Deleted Entries : 0
Alarm Entries : 0
-------------------------------------------------------------------------------
Rem Num Entries : 0
Rem Lcl Deleted Entries : 0
Rem Alarm Entries : 0
-------------------------------------------------------------------------------
Application : subMgmt
Num Entries : 1
Lcl Deleted Entries : 0
Alarm Entries : 0
-------------------------------------------------------------------------------
Rem Num Entries : 1
Rem Lcl Deleted Entries : 0
Rem Alarm Entries : 0
-------------------------------------------------------------------------------
Application : srrp
Num Entries : 0
Lcl Deleted Entries : 0
Alarm Entries : 0
-------------------------------------------------------------------------------
Rem Num Entries : 0
Rem Lcl Deleted Entries : 0
Rem Alarm Entries : 0
===============================================================================
Ports synced on peer 10.10.10.20
===============================================================================
Port/Encap Tag
-------------------------------------------------------------------------------
lag-1 test123
===============================================================================
*A:subscr_mgt_2#
Label |
Description |
---|---|
Peer IP Address |
Displays the multi-chassis redundancy peer. |
Description |
The text string describing the peer. |
Authentication |
If configured, displays the authentication key used between this node and the multi-chassis peer. |
Source IP Address |
Displays the source address used to communicate with the multi-chassis peer. |
Admin State |
Displays the administrative state of the peer. |
Client Applications |
Displays the list of client applications synchronized between routers. |
Sync Admin State |
Displays the administrative state of the synchronization. |
Sync Oper State |
Displays the operation state of the synchronization. |
DB Sync State |
Displays the database state of the synchronization. |
Num Entries |
Displays the number of entries on local router. |
Lcl Deleted Entries |
Displays the number of deleted entries made at the local router. |
Alarm Entries |
Displays the alarm entries on the local router. |
Rem Num Entries |
Displays the number of entries on the remote router. |
Rem Lcl Deleted Entries |
Displays the number of locally deleting entries made by the remote router. |
Rem Alarm Entries |
Displays alarm entries on the remote router. |
sync-database
sync-database
Syntax
sync-database [peer ip-address] [ port port-id | lag-id] [ sync-tag sync-tag] [application application] [detail] [ type type]
Context
[Tree] (tools>dump>redundancy>multi-chassis sync-database)
Full Context
tools dump redundancy multi-chassis sync-database
Description
This command dumps MCS database information.
Parameters
- ip-address
-
Specifies the peer’s IP address.
- port-id | lag-id
-
Indicates the port or LAG ID to be synchronized with the multi-chassis peer.
- sync-tag
-
Specifies a synchronization tag to be used while synchronizing this port with the multi-chassis peer.
- application
-
Specifies a particular multi-chassis peer synchronization protocol application.
- type
-
Indicates the locally deleted or alarmed deleted entries in the MCS database per multi-chassis peer.
- detail
-
Displays detailed information.
Platforms
All
sync-database
Syntax
sync-database [peer ip-address] [port port-id | lag-id] [sync-tag sync-tag] [ application application] [detail] [type type]
sync-database [peer ip-address] [sdp sdp-id] [sync-tag sync-tag] [application application] [detail] [ type type]
Context
[Tree] (tools>dump>redundancy>multi-chassis sync-database)
Full Context
tools dump redundancy multi-chassis sync-database
Description
This command dumps multi-chassis sync database information.
Parameters
- ip-address
-
Dumps the specified address of the multi-chassis peer.
- port-id
-
Dumps the specified port ID of the multi-chassis peer.
- lag-id
-
Dumps the specified Link Aggregation Group (LAG) on this system.
- sync-tag
-
Dumps the synchronization tag used while synchronizing this port with the multi-chassis peer up to 32 characters in length.
- application
-
Dumps the specified application information that was synchronized with the multi-chassis peer.
- detail
-
Displays detailed information.
- type
-
Displays information for the specified type.
- sdp-id
-
Displays information for the specified SDP ID.
Platforms
All
Output
The following output is an example of sync database information.
Output ExampleA:Dut-C# tools dump redundancy multi-chassis sync-database application
<ip-address> : a.b.c.d
<port-id|lag-id> : slot/mda/port or lag-<lag-id>
<sync-tag> : [32 chars max]
<application> : dhcp-server - local dhcp server
igmp - internet group management protocol
igmp-snooping - igmp-snooping
mc-ring - multi-chassis ring
mld - multicast listener discovery
mld-snooping - multicast listener discovery-snooping
srrp - simple router redundancy protocol
sub-host-trk - subscriber host tracking
sub-mgmt-ipoe - subscriber management for IPoE
sub-mgmt-pppoe - subscriber management for PPPoE
mc-ipsec - multi-chassis IPsec
<detail> : - displays detailed information
<type> : alarm-deleted|local-deleted|global-deleted|
omcr-standby|omcr-alarmed
sync-database
Syntax
sync-database peer ip-address all application application
sync-database peer ip-address port { port-id | lag-id} [sync-tag sync-tag] application application
sync-database peer ip-address sdp sdp-id [sync-tag sync-tag] application application
sync-database peer ip-address sync-tag sync-tag application application
Context
[Tree] (clear>redundancy>multi-chassis sync-database)
Full Context
clear redundancy multi-chassis sync-database
Description
This command clears multi-chassis sync database information.
Parameters
- ip-address
-
Clears the specified address of the multi-chassis peer.
- port-id
-
Clears the specified port ID of the multi-chassis peer.
- lag-id
-
Clears the specified Link Aggregation Group (LAG) on this system.
- all
-
Clears all ports and synchronization tags.
- sync-tag
-
Clears the synchronization tag used while synchronizing this port with the multi-chassis peer. The synchronization tag can be up to 32 characters.
- sdp-id
-
Specifies the SDP identifier.
- application
-
Clears the specified application information that was synchronized with the multi-chassis peer.
Platforms
All
sync-database-reconcile
sync-database-reconcile
Syntax
sync-database-reconcile [peer ip-address] [ port port-id | lag-id [sync-tag sync-tag]] [application application]
sync-database-reconcile [peer ip-address] [ sdp sdp-id [sync-tag sync-tag]] [ application application]
Context
[Tree] (tools>perform>redundancy>multi-chassis sync-database-reconcile)
Full Context
tools perform redundancy multi-chassis sync-database-reconcile
Description
This command provides the parameters to reconcile MCS database entries.
Parameters
- ip-address
-
Specifies the IP address (in the form of a.b.c.d).
- port-id
-
Specifies the port ID in the slot/MDA/port format.
- lag-id
-
Specifies the LAG ID.
- syn-tag
-
Specifies the syn tag up to 32 characters.
- application
-
Specifies the application.
- sdp-id
-
Specifies the SDP ID.
Platforms
All
sync-if-timing
sync-if-timing
Syntax
sync-if-timing
Context
[Tree] (show>system>satellite>eth-sat sync-if-timing)
[Tree] (show>system>satellite>tdm-sat sync-if-timing)
Full Context
show system satellite eth-sat sync-if-timing
show system satellite tdm-sat sync-if-timing
Description
This command displays synchronous interface timing operational information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
- show system satellite eth-sat sync-if-timing
7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e
- show system satellite tdm-sat sync-if-timing
Output
The following output is an example of TDM satellite synchronous interface timing information and System Satellite Timing Output Fields describes the fields.
Output Exampleshow system satellite tdm-sat 1 sync-if-timing
===============================================================================
Satellite tsat-1 Synchronous Interface Timing Operational Information
===============================================================================
System Status : Master Locked
System Quality Level : eec2
Current Frequency Offset (ppm) : +0
Reference Input 1
Admin Status : up
Rx Quality Level : eec2
Qualified For Use : yes
Selected For Use : yes
Source Port : tsat-1/1/u1
Reference Input 2
Admin Status : down
Rx Quality Level : unknown
Qualified For Use : no
Not Qualified Due To : disabled
Selected For Use : no
Not Selected Due To : disabled
Source Port : none
===============================================================================
The following output is an example of Ethernet satellite synchronous interface timing information where it is the default case of using the first two uplink ports as sources into the satellite. System Satellite Timing Output Fields describes the fields.
show system satellite eth-sat 1 sync-if-timing
===============================================================================
Satellite esat-1 Synchronous Interface Timing Operational Information
===============================================================================
System Status : Master Locked
System Quality Level : eec1
Quality Level Selection : Enabled
Current Frequency Offset (ppm) : +0
Reference Input 1
Admin Status : up
Rx Quality Level : eec1
Qualified For Use : yes
Selected For Use : yes
Source Port : esat-1/1/c33/u1
Reference Input 2
Admin Status : up
Rx Quality Level : eec1
Qualified For Use : yes
Selected For Use : no
Not Selected Due To : on standby
Source Port : esat-1/1/c35/u1
===============================================================================
The following output is an example of Ethernet satellite synchronous interface timing information for the case where one of the client ports has been configured as an input reference. System Satellite Timing Output Fields describes the fields.
show system satellite eth-sat 1 sync-if-timing
===============================================================================
Satellite esat-1 Synchronous Interface Timing Operational Information
===============================================================================
System Status : Master Locked
System Quality Level : eec1
Quality Level Selection : Enabled
Current Frequency Offset (ppm) : +0
Reference Input 1
Admin Status : up
Rx Quality Level : eec1
Qualified For Use : yes
Selected For Use : no
Not Selected Due To : on standby
Source Port : esat-1/1/c1/1
Reference Input 2
Admin Status : up
Rx Quality Level : eec1
Qualified For Use : yes
Selected For Use : yes
Source Port : esat-1/1/c35/u1
===============================================================================
Label |
Description |
---|---|
System Status |
Indicates the system status |
System Quality Level |
Indicates the quality level being generated by the system clock |
Quality Level Selection |
Indicates the quality level selection status |
Current Frequency Offset (ppm) |
Indicates the offset that is applied within the central clock to align the local oscillator to the frequency of the selected input reference. The units for this value are parts per million (ppm). This value should not be misinterpreted as an indicator of the frequency accuracy of the output of the central clock. If the central clock is locked to a true Primary Reference Clock or Stratum 1 frequency reference, this value should report a number within the range [-5, +5] ppm. |
Reference Input 1/2 |
|
Admin Status |
down — Indicates ref1 or ref2 configuration is administratively shutdown up — Indicates ref1 or ref2 configuration is administratively enabled diag — Indicates the reference has been forced using the force-reference command |
Rx Quality Level |
Indicates the QL value received on the interface
|
Quality Level Override |
Indicates whether the QL value used to determine the reference was configured directly by the user |
Qualified for Use |
Indicates whether the reference has been qualified to be used as a source of timing for the node |
Not Qualified Due To |
Indicates the reason why the reference has not been qualified |
Selected for Use |
Indicates whether the method is presently selected |
Not Selected Due To |
Indicates the reason why the method is not selected:
|
Source Port |
Identifies the source port for the reference |
sync-if-timing
Syntax
sync-if-timing [cpm-slot]
Context
[Tree] (show>system sync-if-timing)
Full Context
show system sync-if-timing
Description
This command displays synchronous interface timing operational information.
Parameters
- cpm-slot
-
Specifies the system CPM slot.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of sync-if-timing information, and System Timing Output describes the output fields.
Output ExampleThe following system example shows:
-
sync-if timing, or
-
sync-if-timing "A” when the SETS reference on the active CPM-A locks to BITS A, or
-
sync-if-timing "B” when the SETS reference on the active CPM-B locks to BITS A
The following output applies only to the 7750 SR-1e/2e/3e and 7950 XRS-16/20/40 platforms.
*A:Dut-B# show system sync-if-timing or show system sync-if-timing "A"
===============================================================================
System Interface Timing Operational Info
===============================================================================
System Status CPM A : Master Locked
Reference Input Mode : Revertive
Quality Level Selection : Disabled
Reference Selected : BITS A
System Quality Level : prc
Current Frequency Offset (ppm) : +0
Input Minimum Quality Level : st3
Wait to Restore Timer : Disabled
Reference Order : bits ref1 ref2
Reference Input 1
Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : on standby
Source Port : 1/1/5
Reference Input 2
Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : on standby
Source Port : 3/1/5
Reference BITS A
Input Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : Yes
Interface Type : E1
Framing : PCM31 CRC
Line Coding : HDB3
SSM Bit : 8
Output Admin Status : up
Output Minimum Quality Level : st2
Output Source : line reference
Output Reference Selected : ref1
Output Squelch : Disabled
Tx Quality Level : prc
Reference BITS B
Input Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : on standby
Interface Type : E1
Framing : PCM31 CRC
Line Coding : HDB3
SSM Bit : 8
Output Admin Status : up
Output Minimum Quality Level : st2
Output Source : line reference
Output Reference Selected : ref1
Output Squelch : Disabled
Tx Quality Level : prc
===============================================================================
The following system example shows:
-
sync-if timing standby, or
-
sync-if-timing "B” when the SETS reference on the standby CPM-B locks to Mate CPM (BITS A), or
-
sync-if-timing "A” when the SETS reference on the standby CPM-A locks to Mate CPM (BITS A)
The following output applies only to the 7750 SR-1e/2e/3e and 7950 XRS-16/20/40 platforms.
---------------------------------------------------------------------------
*A:Dut-B# show system sync-if-timing standby or show system sync-if-timing "B"
===============================================================================
System Interface Timing Operational Info
===============================================================================
System Status CPM B : Master Locked
Reference Input Mode : Revertive
Quality Level Selection : Disabled
Reference Selected : Mate CPM (BITS A)
System Quality Level : prc
Current Frequency Offset (ppm) : +0sync-if-timing "A
Input Minimum Quality Level : st3
Wait to Restore Timer : Disabled
Reference Order : bits ref1 ref2
Reference Mate CPM
Qualified For Use : Yes
Selected For Use : Yes
Reference Input 1
Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : on standby
Source Port : 1/1/5
Reference Input 2
Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : on standby
Source Port : 3/1/5
Reference BITS A
Input Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : on standby
Interface Type : E1
Framing : PCM31 CRC
Line Coding : HDB3
SSM Bit : 8
Output Admin Status : up
Output Minimum Quality Level : st2
Output Source : line reference
Output Reference Selected : ref1
Output Squelch : Disabled
Tx Quality Level : prc
Reference BITS B
Input Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : on standby
Interface Type : E1
Framing : PCM31 CRC
Line Coding : HDB3
SSM Bit : 8
Output Admin Status : up
Output Minimum Quality Level : st2
Output Source : line reference
Output Reference Selected : ref1
Output Squelch : Disabled
Tx Quality Level : prc
===============================================================================
The following system example shows:
-
sync-if timing, or
-
sync-if-timing "A” when the SETS reference on the active CPM-A locks to BITS B, or
-
sync-if-timing "B” when the SETS reference on the active CPM-B locks to BITS B
The following output applies only to the 7750 SR-1e/2e/3e and 7950 XRS-16/20/40 platforms.
--------------------------------------------------------------------
*A:Dut-B# show system sync-if-timing or show system sync-if-timing "A"
===============================================================================
System Interface Timing Operational Info
===============================================================================
System Status CPM A : Master Locked
Reference Input Mode : Non-revertive
Quality Level Selection : Disabled
Reference Selected : BITS B
System Quality Level : prc
Current Frequency Offset (ppm) : +0
Input Minimum Quality Level : st3
Wait to Restore Timer : Disabled
Reference Order : bits ref1 ref2
Reference Input 1
Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : on standby
Source Port : 1/1/5
Reference Input 2
Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : on standby
Source Port : 3/1/5
Reference BITS A
Input Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : previous failure
Interface Type : E1
Framing : PCM31 CRC
Line Coding : HDB3
SSM Bit : 8
Output Admin Status : up
Output Minimum Quality Level : st2
Output Source : line reference
Output Reference Selected : ref1
Output Squelch : Disabled
Tx Quality Level : prc
Reference BITS B
Input Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : Yes
Interface Type : E1
Framing : PCM31 CRC
Line Coding : HDB3
SSM Bit : 8
Output Admin Status : up
Output Minimum Quality Level : st2
Output Source : line reference
Output Reference Selected : ref1
Output Squelch : Disabled
Tx Quality Level : prc
===============================================================================
The following system example shows:
-
sync-if timing standby, or
-
sync-if-timing "B” when the SETS reference on the standby CPM-B locks to Mate CPM (BITS B), or
-
sync-if-timing "A” when the SETS reference on the standby CPM-A locks to Mate CPM (BITS B)
The following output applies only to the 7750 SR-1e/2e/3e and 7950 XRS-16/20/40 platforms.
--------------------------------------------------------------------
*A:Dut-B# show system sync-if-timing standby or show system sync-if-timing "B"
===============================================================================
System Interface Timing Operational Info
===============================================================================
System Status CPM B : Master Locked
Reference Input Mode : Non-revertive
Quality Level Selection : Disabled
Reference Selected : Mate CPM (BITS B)
System Quality Level : prc
Current Frequency Offset (ppm) : +0
Input Minimum Quality Level : st3
Wait to Restore Timer : Disabled
Reference Order : bits ref1 ref2
Reference Mate CPM
Qualified For Use : Yes
Selected For Use : Yes
Reference Input 1
Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : on standby
Source Port : 1/1/5
Reference Input 2
Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : on standby
Source Port : 3/1/5
Reference BITS A
Input Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : previous failure
Interface Type : E1
Framing : PCM31 CRC
Line Coding : HDB3
SSM Bit : 8
Output Admin Status : up
Output Minimum Quality Level : st2
Output Source : line reference
Output Reference Selected : ref1
Output Squelch : Disabled
Tx Quality Level : prc
Reference BITS B
Input Admin Status : up
Rx Quality Level : prc
Quality Level Override : none
Qualified For Use : Yes
Selected For Use : No
Not Selected Due To : on standby
Interface Type : E1
Framing : PCM31 CRC
Line Coding : HDB3
SSM Bit : 8
Output Admin Status : up
Output Minimum Quality Level : st2
Output Source : line reference
Output Reference Selected : ref1
Output Squelch : Disabled
Tx Quality Level : prc
===============================================================================
Label |
Description |
---|---|
System Status CPM A/B |
Indicates the present status of the synchronous timing equipment subsystem (SETS). Not Present — Only shown on systems without central clocks Master Freerun — The clock is in free-run because it hasn’t had a qualified input reference to lock to Master Holdover — The clock was locked to an input reference but has lost all qualified input references and is in holdover. Master Locked — The clock is locked to an input reference Acquiring — The clock is training to a qualified input reference. |
Reference Input Mode |
Revertive — Indicates that for a re-validated or a newly validated reference source which has a higher priority than the currently selected reference has reverted to the new reference source. Non-revertive — The clock cannot revert to a higher priority clock if the current clock goes offline. |
Quality Level Selection |
Indicates whether the ql-selection command has been enabled or disabled. If this command is enabled, then the reference is selected first using the QL value, then by the priority reference order. If this command is not enabled, then the reference is selected by the priority reference order. |
Reference Selected |
Indicates which reference has been selected:
|
|
|
System Quality Level |
Indicates the quality level being generated by the system clock. |
Current Frequency Offset |
This value indicates the offset that is applied within the central clock to align the local oscillator to the frequency of the selected input reference. The units for this value are parts per million (ppm). This value should not be misinterpreted as an indicator of the frequency accuracy of the output of the central clock. If the central clock is locked to a true Primary Reference Clock or Stratum 1 frequency reference, this value should report a number within the range [-5, +5] ppm. |
Input Minimum Quality Level |
The configured minimum acceptable QL to consider for use by the central clock. |
Wait to Restore Timer |
The configured timeout to use for the Wait to Restore timer. |
Reference Order |
ref1, ref2, bits — Indicates that the priority order of the timing references. |
Reference Mate CPM |
Data within this block represents the status of the timing reference provided by the Mate CPM. This will be the BITS input from the standby CPM. |
Admin Status |
down — The ref1 or ref2 configuration is administratively shutdown. up — The ref1 or ref2 configuration is administratively enabled. diag — Indicates the reference has been forced using the force-reference command. |
Quality Level Override |
Indicates whether the QL value used to determine the reference was configured directly by the user. |
Rx Quality Level |
Indicates the QL value received on the interface.
|
Qualified for Use |
Indicates whether the reference has been qualified to be used as a source of timing for the node. |
Not Qualified Due To |
Indicates the reason why the reference has not been qualified:
|
Selected for Use |
Indicates whether the method is presently selected. |
Not Selected Due To |
Indicates the reason why the method is not selected:
|
Source Port |
Identifies the Source port for the reference. |
Interface Type |
The interface type configured for the BITS port. |
Framing |
The framing configured for the BITS port. |
Line Coding |
The line coding configured for the BITS port. |
Line Length |
The line length value of the BITS output. |
Output Admin Status |
down — The BITS output is administratively shutdown. up — The BITS output is administratively enabled. |
Output Minimum Quality Level |
The configured minimum acceptable QL to use for the BITSout signal. |
Output Source |
The source to be used to provide the signal on the BITS output port. line reference — unfiltered recovered line reference. internal clock — filtered node clock output. |
Output Reference Selected |
The reference selected as the source for the BITS output signal (ref1, ref2, or PTP). |
Output Squelch |
Indicates whether the squelch function for BITSout is enabled or disabled. |
TX Quality Level |
QL value for BITS output signal. |
sync-if-timing
Syntax
sync-if-timing {ref1 | ref2 | bits | bitsa | bitsb | gnss | gnssa | gnssb | synce | syncea | synceb }
Context
[Tree] (clear>system sync-if-timing)
Full Context
clear system sync-if-timing
Description
This command individually clears (re-enables) a previously failed reference. As long as the reference is one of the valid options, this command is always executed. An inherent behavior enables the revertive mode which causes a reevaluation of all available references.
The timing options may vary depending on the platform because not all options are supported on all platforms.
This command also clears the Wait-to-Restore state of the reference so that it can be selected.
Parameters
- ref1
-
Clears the first timing reference.
- ref2
-
Clears the second timing reference.
- bits
-
Clears the bits timing reference on the CPM.
- bitsa
-
Clears the BITS port timing reference of CPM A for redundant systems with a BITS port on each CPM.
- bitsb
-
Clears the BITS port timing reference of CPM B for redundant systems with a BITS port on each CPM.
- gnss
-
Clears the GNSS port timing reference. This keyword is only supported on 7750 SR single‑slot FP5 platforms.
- gnssa
-
Clears the GNSS port timing reference for the CPM in slot A. This keyword is only supported on 7750 SR-2se platforms.
- gnssb
-
Clears the GNSS port timing reference for the CPM in slot B. This keyword is only supported on 7750 SR-2se platforms.
- synce
-
Clears the SyncE/1588 port timing reference. This keyword is only supported on single slot systems.
- syncea
-
Clears the SyncE/1588 port of the CPM A timing reference. This keyword is only supported on platforms supporting redundant CPM.
- synceb
-
Clears the SyncE/1588 port of the CPM B timing reference. This keyword is only suported on platforms supporting redundant CPM.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
sync-if-timing
Syntax
sync-if-timing reference
Context
[Tree] (clear>system>satellite>eth-sat sync-if-timing)
Full Context
clear system satellite eth-sat sync-if-timing
Description
This command clears (re-enables) a previously failed reference on the Ethernet satellite.
Parameters
- reference
-
Specifies to clear the first or second timing reference.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
sync-if-timing
Syntax
sync-if-timing reference
Context
[Tree] (clear>system>satellite>tdm-sat sync-if-timing)
Full Context
clear system satellite tdm-sat sync-if-timing
Description
This command clears (re-enables) a previously failed reference on the TDM satellite.
Parameters
- reference
-
Specifies to clear the first or second timing reference.
Platforms
7450 ESS, 7750 SR-7/12/12e, 7750 SR-a, 7750 SR-e
synchronization
synchronization
Syntax
synchronization
Context
[Tree] (show>redundancy synchronization)
Full Context
show redundancy synchronization
Description
This command displays redundancy synchronization times.
Platforms
All
Output
The following output is an example of redundancy synchronization information, and Synchronization Output describes the output fields.
Output ExampleA:ALA-1>show>redundancy# synchronization
===============================================================================
Synchronization Information
===============================================================================
Standby Status : disabled
Last Standby Failure : N/A
Standby Up Time : N/A
Failover Time : N/A
Failover Reason : N/A
Boot/Config Sync Mode : None
Boot/Config Sync Status : No synchronization
Last Config File Sync Time : Never
Last Boot Env Sync Time : Never
===============================================================================
A:ALA-1>show>redundancy#
Label |
Description |
---|---|
Standby Status |
Displays the status of the standby CPM. |
Last Standby Failure |
Displays the timestamp of the last standby failure. |
Standby Up Time |
Displays the length of time the standby CPM has been up. |
Failover Time |
Displays the timestamp when the last redundancy failover occurred causing a switchover from active to standby CPM. If there is no redundant CPM card in this system or no failover has occurred since the system last booted, the value will be 0. |
Failover Reason |
Displays a text string giving an explanation of the cause of the last redundancy failover. If no failover has occurred, an empty string displays. |
Boot/Config Sync Mode |
Displays the type of synchronization operation to perform between the primary and secondary CPMs after a change has been made to the configuration files or the boot environment information contained in the boot options file (BOF). |
Boot/Config Sync Status |
Displays the results of the last synchronization operation between the primary and secondary CPMs. |
Last Config File Sync Time |
Displays the timestamp of the last successful synchronization of the configuration files. |
Last Boot Env Sync Time |
Displays the timestamp of the last successful synchronization of the boot environment files. |
syslog
syslog
Syntax
syslog [syslog-id]
Context
[Tree] (show>service>id>log syslog)
Full Context
show service id log syslog
Description
This command displays syslog event log destination summary information or detailed information on a specific syslog destination.
Parameters
- syslog-id
-
Displays detailed information on the specified syslog event log destination.
Platforms
All
Output
Syslog Event Log Destination Summary Output
Show Log Syslog Field Descriptions describes the syslog output fields.
Label |
Description |
---|---|
Syslog ID |
The syslog ID number for the syslog destination. |
IP Address |
The IP address of the syslog target host. |
Port |
The configured UDP port number used when sending syslog messages. |
Facility |
The facility code for messages sent to the syslog target host. |
Severity Level |
The syslog message severity level threshold. |
Below Level Dropped |
A count of messages not sent to the syslog collector target because the severity level of the message was above the configured severity. The higher the level, the lower the severity. |
Prefix Present |
Yes — A log prefix was prepended to the syslog message sent to the syslog host. No — A log prefix was not prepended to the syslog message sent to the syslog host. |
Description |
A text description stored in the configuration file for a configuration context. |
LogPrefix |
The prefix string prepended to the syslog message. |
Log-id |
Events are directed to this destination. |
syslog
Syntax
syslog
Context
[Tree] (show>service>nat syslog)
Full Context
show service nat syslog
Description
This command enters the conect to display NAT syslog information
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
syslog
Syntax
syslog [syslog-id]
Context
[Tree] (show>log syslog)
Full Context
show log syslog
Description
This command displays Syslog event log destination summary information or detailed information on a specific Syslog destination.
Parameters
- syslog-id
-
Displays detailed information on the specified Syslog event log destination.
Platforms
All
Output
The following output is an example of Syslog information.
Show Log Syslog Output Fields describes the Syslog output fields.
Output Example*A:ALA-48>config>log# show log syslog
===============================================================================
Syslog Target Hosts
===============================================================================
Syslog Ip Address Port Sev Level
Name/ Below Level Drop Facility Pfx Level
Id
-------------------------------------------------------------------------------
2 unknown 514 info
0 local7 yes
3 unknown 514 info
0 local7 yes
5 unknown 514 info
0 local7 yes
10 unknown 514 info
0 local7 yes
===============================================================================
*A:ALA-48>config>log#
*A:MV-SR>config>log# show log syslog 1
===============================================================================
Syslog Target 1
===============================================================================
IP Address : 192.168.15.22
Port : 514
Log-ids : none
Prefix : Sr12
Facility : local1
Severity Level : info
Prefix Level : yes
Below Level Drop : 0
Description : Linux Station Springsteen
===============================================================================
*A:MV-SR>config>log#
Label |
Description |
---|---|
Syslog Name/Id |
The Syslog ID or name for the Syslog destination. |
IP Address |
The IP address of the Syslog target host. |
Port |
The configured UDP port number used when sending Syslog messages. |
Facility |
The facility code for messages sent to the Syslog target host. |
Severity Level |
The Syslog message severity level threshold. |
Below Level Dropped |
A count of messages not sent to the Syslog collector target because the severity level of the message was above the configured severity. The higher the level, the lower the severity. |
Prefix Present |
Yes — A log prefix was prepended to the Syslog message sent to the syslog host. No — A log prefix was not prepended to the Syslog message sent to the syslog host. |
Description |
A text description stored in the configuration file for a configuration context. |
LogPrefix |
The prefix string prepended to the Syslog message. |
Log-id |
Events are directed to this destination. |
syslog-export-policy
syslog-export-policy
Syntax
syslog-export-policy name associations
syslog-export-policy name
syslog-export-policy
Context
[Tree] (show>service>nat>syslog syslog-export-policy)
Full Context
show service nat syslog syslog-export-policy
Description
This command displays information about syslog export policies.
Parameters
- name
-
Displays information about the specified NAT syslog export policy.
- associations
-
Displays where the syslog-export-policy is configured.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of syslog export policy information.
Output Example*SR-OS-NODE-1# show service nat syslog syslog-export-policy <name>
===============================================================================
NAT syslog policy
===============================================================================
Description
Facility
Log prefix
Max tx delay (deciseconds)
MTU
Rate limit (pps)
Severity level
Includes
Last management change
-------------------------------------------------------------------------------
Collectors
-------------------------------------------------------------------------------
Router
Source IP address
Administrative state
Destination port
IP address
Last management change
-------------------------------------------------------------------------------
The following output is an example of syslog export policy associations.
Output Example*A:Dut-C# show service nat syslog syslog-export-policy <name> associations
===============================================================================
policies with syslog-export-policy <name>
===============================================================================
Policy
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
No. of policies
===============================================================================
The following output is an example of syslog-export-policy <name> information.
*A:Dut-C# show service nat nat-policy <name>
===============================================================================
NAT Policy policy_lsn_1_3
===============================================================================
Description :
Pool :
Router :
Filtering :
Block limit :
Reserved ports :
Port usage High Watermark (%) :
Port usage Low Watermark (%) :
Port forwarding limit :
Port forwarding range end :
Session limit :
Reserved sessions :
Session usage High Watermark (%) :
Session usage Low Watermark (%) :
ALG enabled :
Prioritized forwarding classes :
Timeout TCP established (s) :
Timeout TCP transitory (s) :
Timeout TCP SYN (s) :
Timeout TCP TIME-WAIT (s) :
Timeout TCP RST (s) :
Timeout UDP mapping (s) :
Timeout UDP initial (s) :
Timeout UDP DNS (s) :
Timeout ICMP Query (s) :
Timeout SIP Inactive Media (s) :
Subscriber retention (s) :
UDP inbound refresh :
TCP MSS Adjust :
Destination NAT classifier :
Destination-NAT-only router :
Destination-NAT-only ISA NAT group :
IPFIX export policy :
Syslog export policy syslog-export-policy associated with this nat-policy
Reset unknown TCP :
L2 outside :
Last Mgmt Change :
The following output is an example of syslog-export-policy information.
*A:Dut-C>show>service>nat>syslog# syslog-export-policy
===============================================================================
Syslog export policies
===============================================================================
Syslog export policy
Description description of each syslog-export-policy
-------------------------------------------------------------------------------
No. of syslog export policies:
syslog-export-policy Fields displays syslog export policy field descriptions.
Field |
Description |
---|---|
Description |
Displays the description for the syslog export policy. |
Facility |
Displays information about the facility. Valid values: kernel, user, mail, systemd, auth, syslogd, printer, netnews, uucp, cron, authpriv, ftp, ntp, logaudit, logalert, cron2, local0, local1, local2, local3, local4, local5, local6, local7 |
Log prefix |
Displays information about the log prefix. |
Max tx delay (deciseconds) |
Displays the time waited to aggregate multiple events info a single log message (event aggregation). |
MTU |
Displays information about the IP MTU of the syslog frame. |
Rate limit (pps) |
Displays the rate limit imposed on syslog frames sent toward the collector. |
Severity level |
Displays the syslog severity level. Valid values: emergency, alert, critical, error, warning, notice, info, debug |
Includes |
Displays the optional fields related to the flow that can be included in the flow log message. |
Last management change |
Displays the time and date of the last configuration change. |
Router |
Displays the routing instance from which the collector is reachable. |
Source IP address |
Displays the source IP address of the syslog frame. |
Administrative state |
Displays the administrative state of the collector. |
Destination port |
Displays the destination port of the collector. |
IP address |
Displays the IP address of the collector. |
Syslog export policy |
Displays the syslog export policy associated with this NAT policy. |
No. of syslog export policies |
Displays the number of syslog export policies configured in the system. |
system
system
Syntax
system
Context
[Tree] (show system)
Full Context
show system
Description
Commands in this context display system information.
Platforms
All
system
Syntax
system
Context
[Tree] (tools>perform system)
Full Context
tools perform system
Description
This command is a tool for controlling the system.
Platforms
All
system
Syntax
system
Context
[Tree] (show>service system)
Full Context
show service system
Description
Commands in this context display service system information.
Platforms
All
system
Syntax
system [all]
Context
[Tree] (tools>dump>resource-usage system)
Full Context
tools dump resource-usage system
Description
This command displays resource information for resources that are managed at the system level.
Parameters
- all
-
Displays all system resource usage information, as well as resource usage information for all cards, FPs, and MDAs in the system.
Platforms
All
Output
The following output is an example of system information.
Output Example*A:PE# tools dump resource-usage system
===============================================================================
Resource Usage Information for System
===============================================================================
Total Allocated Free
-------------------------------------------------------------------------------
SAP Ingress QoS Policies | 3071 1 3070
SAP Egress QoS Policies | 3071 2 3069
Ingress Queue-Group Templates | 2047 4 2043
Egress Queue-Group Templates | 2047 5 2042
Egress Port Queue-Group Instances | 163839 4 163835
Ingress FP Queue-Group Instances | 16383 0 16383
Fast Depth Monitored Queues | 50000 25 49975
Egress Port VPort | 40959 1 40958
system
Syntax
system
Context
[Tree] (clear system)
Full Context
clear system
Description
This command allows an operator to clear system information.
Platforms
All
system
Syntax
system
Context
[Tree] (tools>dump system)
Full Context
tools dump system
Description
Commands in this context dump tools for system.
Platforms
All
system
Syntax
system
Context
[Tree] (tools>dump>service system)
Full Context
tools dump service system
Description
Commands in this context dump service system information.
Platforms
All
system
Syntax
system status
Context
[Tree] (show>subscr-mgmt>status system)
Full Context
show subscriber-mgmt status system
Description
This command displays subscriber management status information.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
Output
The following output is an example of subscriber management system status information.
Output Example*B:Dut-C# show subscriber-mgmt status system
===============================================================================
Subscriber Management System Status
===============================================================================
Chassis 1
-------------------------------------------------------------------------------
Memory usage high : No
DHCP message processing overload : No
Statistics usage high : No
Number of subscribers using statistics : 0
Data-trigger statistics
-------------------------------------------------------------------------------
Packets received : 0
Packets dropped : 0
Packets in queue (actual) : 0
Packets in queue (peak) : 1
Bridged Residential Gateway statistics
-------------------------------------------------------------------------------
BRG initialized : 0
BRG operational : 0
BRG in connectivity verification : 0
BRG on hold : 0
BRG authenticated by proxy : 0
Subscriber VLAN statistics resources
-------------------------------------------------------------------------------
Administrative state : in-service
Number of entries : 2
Interface statistics resources
-------------------------------------------------------------------------------
Administrative state sub-if : in-service
Number of sub-if stats entries : 1
Administrative state grp-if : in-service
Number of grp-if stats entries : 2
===============================================================================
*B:Dut-C#
system-config
system-config
Syntax
system-config
Context
[Tree] (show>eth-cfm system-config)
Full Context
show eth-cfm system-config
Description
This command shows various ETH-CFM system-level configuration parameters under the config> eth-cfm [{redundancy | slm | system}] hierarchies and various system capabilities.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of ETH-CFM system-level configuration information.
Output Exampleshow eth-cfm system-config
===============================================================================
CFM System Configuration
===============================================================================
Redundancy
MC-LAG Standby MEP Shutdown: false
MC-LAG Hold-Timer : 1 second(s)
Synthetic Loss Measurement
Inactivity Timer : 100 second(s)
ETH-CCM Grace-Period
Transmit Enabled : true
Sender ID Information
ChassisID Subtype : chassisComponent
MD Auto-Id Range Information
md-index start : 3294967295
md-index end : 4294967295
ma-index start : 3294967295
ma-index end : 4294967295
Display
Name-based display : false
-------------------------------------------------------------------------------
ETH-CFM System Configuration Limits
-------------------------------------------------------------------------------
Component Current Usage System Limit
-------------------------------------------------------------------------------
Maintenance Domain (MD) 2 25000
Maintenance Association (MA) 2 25000
Extended MA (up to 400 MEPs) 0 10
Maintenance Endpoint (MEP) 2 25000
One-second MEP 1 10000
Sub-second MEP 0 7000
Alarm Indication Signal (AIS) 0 25000
Client Signal Fail (CSF) 0 25000
Primary Vlan Ingress MP 0 19999
Primary Vlan Egress MP 0 19999
LMM Stats Enabled 0 8000
LBM Concurrent Tests 0 1000
Multicast LB Tests 0 10
LTM Concurrent Tests 0 100
-------------------------------------------------------------------------------
===============================================================================
MD Auto-Id Range Information
md-index start : 3000000000
md-index end : 4000000000
ma-index start : 3000000000
ma-index end : 4000000000
-------------------------------------------------------------------------------
ETH-CFM System Configuration Limits
-------------------------------------------------------------------------------
Component Current Usage System Limit
-------------------------------------------------------------------------------
Maintenance Domain (MD) 9 25000
Maintenance Association (MA) 26 25000
Extended MA (up to 400 MEPs) 0 10
Maintenance Endpoint (MEP) 18 25000
One-second MEP 16 5000
Sub-second MEP 0 5000
Alarm Indication Signal (AIS) 2 25000
Client Signal Fail (CSF) 0 25000
Primary Vlan Ingress MP 3 19999
Primary Vlan Egress MP 3 19999
LMM Stats Enabled 1 8000
LBM Concurrent Tests 0 100
Multicast LB Tests 0 10
LTM Concurrent Tests 0 100
system-filter
system-filter
Syntax
system-filter [chained-to]
Context
[Tree] (show>filter system-filter)
Full Context
show filter system-filter
Description
This command shows system filter information.
Parameters
- chained-to
-
Displays filters that chain to a given system filter.
Platforms
All
Output
No Parameters Specified — When no parameters are specified, the output is grouped for IPv4 and IPv6, and displays information about the active system filter and all filters with scope system.
The following output is an example of system filter information when no parameters are specified.
Output Example*A:Dut-C>show>filter# system-filter
===============================================================================
IP system filters
===============================================================================
Filter-Id Active
-------------------------------------------------------------------------------
100 Yes
65535 No
-------------------------------------------------------------------------------
No. of IP system filters (total / active): 2 / 1
===============================================================================
===============================================================================
IPv6 system filters
===============================================================================
Filter-Id Active
-------------------------------------------------------------------------------
No Matching Entries
-------------------------------------------------------------------------------
No. of IPv6 system filters (total / active): 0 / 0
===============================================================================
With chained-to Option Specified — The following output is an example of system filter information when the chained-to option is specified.
*A:Dut-C>show>filter# system-filter chained-to
============================================================================
IP filters that chain to the active IP system filter
============================================================================
3 4 5 6
5:23 6:24
----------------------------------------------------------------------------
No. of IP filters that chain to the active IP system filter: 6
============================================================================
============================================================================
IPv6 filters that chain to the active IPv6 system filter
============================================================================
No Matching Entries
----------------------------------------------------------------------------
No. of IPv6 filters that chain to the active IPv6 system filter: 0
============================================================================
system-info
system-info
Syntax
system-info
Context
[Tree] (show>eth-cfm system-info)
Full Context
show eth-cfm system-info
Description
This command displays system-level ETH-CFM information states.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, 7950 XRS
Output
The following output is an example of system-level ETH-CFM information.
Output Exampleshow eth-cfm system-info
===============================================================================
CFM System State Information
===============================================================================
ETH-CCM Grace-Period : Inactive
===============================================================================
system-statistics
system-statistics
Syntax
system-statistics data-trigger
Context
[Tree] (clear>subscr-mgmt system-statistics)
Full Context
clear subscriber-mgmt system-statistics
Description
This command clears subscriber statistics at the system level.
Parameters
- data-trigger
-
Clears data trigger statistics for all data trigger enabled SAPs in the system.
Platforms
7450 ESS, 7750 SR, 7750 SR-a, 7750 SR-e, 7750 SR-s, VSR
system-statistics
Syntax
system-statistics
Context
[Tree] (clear>nat system-statistics)
Full Context
clear nat system-statistics
Description
This command clears NAT statistics at the system level.
Platforms
7450 ESS, 7750 SR, 7750 SR-e, 7750 SR-s, VSR