PORT
SFPStatusBlocked
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2060 |
Event name | SFPStatusBlocked |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.36 |
Default severity | minor |
Message format string | SFF blocked by culprit |
Cause | The tmnxEqPortSFPStatusFailure notification is generated when the tmnxPortSFPStatus of an SFF results in a value other than 'not-equipped (0)', or 'operational (1)'. tmnxEqPortSFPStatusFailure obsoleted tmnxEqPortSFPCorrupted for revision 6.0 on Nokia SR OS series systems. |
Effect | The SFF device is not operational and the associated port cannot be used. The SFF and port will not recover without operator intervention. |
Recovery | Remove and re-insert the SFF device. If the problem persists then replace the SFF device. |
SFPStatusCulprit
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2059 |
Event name | SFPStatusCulprit |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.36 |
Default severity | minor |
Message format string | SFF is culprit |
Cause | The tmnxEqPortSFPStatusFailure notification is generated when the tmnxPortSFPStatus of an SFF results in a value other than 'not-equipped (0)', or 'operational (1)'. tmnxEqPortSFPStatusFailure obsoleted tmnxEqPortSFPCorrupted for revision 6.0 on Nokia SR OS series systems. |
Effect | The SFF device is not operational and the associated port cannot be used. The SFF and port will not recover without operator intervention. |
Recovery | Remove and re-insert the SFF device. If the problem persists then replace the SFF device. |
SFPStatusDDMCorrupt
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2031 |
Event name | SFPStatusDDMCorrupt |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.36 |
Default severity | minor |
Message format string | SFP/XFP DDM Checksums do not match |
Cause | The tmnxEqPortSFPStatusFailure notification is generated when the tmnxPortSFPStatus of an SFF results in a value other than 'not-equipped (0)', or 'operational (1)'. tmnxEqPortSFPStatusFailure obsoleted tmnxEqPortSFPCorrupted for revision 6.0 on Nokia SR OS series systems. |
Effect | The SFF device is not operational and the associated port cannot be used. The SFF and port will not recover without operator intervention. |
Recovery | Remove and re-insert the SFF device. If the problem persists then replace the SFF device. |
SFPStatusFailure
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2008 |
Event name | SFPStatusFailure |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.36 |
Default severity | minor |
Message format string | SFF Checksums do not match |
Cause | The tmnxEqPortSFPStatusFailure notification is generated when the tmnxPortSFPStatus of an SFF results in a value other than 'not-equipped (0)', or 'operational (1)'. tmnxEqPortSFPStatusFailure obsoleted tmnxEqPortSFPCorrupted for revision 6.0 on Nokia SR OS series systems. |
Effect | The SFF device is not operational and the associated port cannot be used. The SFF and port will not recover without operator intervention. |
Recovery | Remove and re-insert the SFF device. If the problem persists then replace the SFF device. |
SFPStatusOperational
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2061 |
Event name | SFPStatusOperational |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.36 |
Default severity | minor |
Message format string | SFF operational |
Cause | The event is generated when the SFF does not undergo a removal or insertion but it recovers from an error state. This can happen when an SFF device with tmnxPortSFPStatus 'culprit (6)' is removed, and the state of the other affected SFF devices with tmnxPortSFPStatus 'blocked (7)' clear back to tmnxPortSFPStatus 'operational (1)'. |
Effect | The SFF device is operational. |
Recovery | N/A |
SFPStatusReadError
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2032 |
Event name | SFPStatusReadError |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.36 |
Default severity | minor |
Message format string | SFP/XFP Read failure |
Cause | The tmnxEqPortSFPStatusFailure notification is generated when the tmnxPortSFPStatus of an SFF results in a value other than 'not-equipped (0)', or 'operational (1)'. tmnxEqPortSFPStatusFailure obsoleted tmnxEqPortSFPCorrupted for revision 6.0 on Nokia SR OS series systems. |
Effect | The SFF device is not operational and the associated port cannot be used. The SFF and port will not recover without operator intervention. |
Recovery | Remove and re-insert the SFF device. If the problem persists then replace the SFF device. |
SFPStatusUnsupported
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2033 |
Event name | SFPStatusUnsupported |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.36 |
Default severity | minor |
Message format string | SFP/XFP unsupported type |
Cause | The tmnxEqPortSFPStatusFailure notification is generated when the tmnxPortSFPStatus of an SFF results in a value other than 'not-equipped (0)', or 'operational (1)'. tmnxEqPortSFPStatusFailure obsoleted tmnxEqPortSFPCorrupted for revision 6.0 on Nokia SR OS series systems. |
Effect | The SFF device is not operational and the associated port cannot be used. The SFF and port will not recover without operator intervention. |
Recovery | Remove and re-insert the SFF device. If the problem persists then replace the SFF device. |
tmnxBundleMemberMlfrLoopback
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2035 |
Event name | tmnxBundleMemberMlfrLoopback |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.39 |
Default severity | minor |
Message format string | Mlfr Bundle Member $tmnxPortPortID$ Loopback $tmnxBundleMemberMlfrDownReason$ |
Cause | Generated when a Multilink Frame-Relay Bundle Member enters or leaves the 'loopback (3)' state. |
Effect | N/A |
Recovery | N/A |
tmnxCellPortCbsdAuthorized
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2080 |
Event name | tmnxCellPortCbsdAuthorized |
SNMP notification prefix and OID | TIMETRA-CELLULAR-MIB.tmnxCellularNotifications.9 |
Default severity | minor |
Message format string | CBSD $tmnxPortPortID$ Authorized - CBSD Id: $tmnxCellPortCbsdAuthId$, Grant Id: $tmnxCellPortCbsdAuthGrantId$, Grant expire time: $tmnxCellPortCbsdAuthGrantExpTime$, Heartbeat interval: $tmnxCellPortCbsdAuthHeartbeatInt$ seconds |
Cause | The tmnxCellPortCbsdAuthorized notification is generated when the CBSD is authorized by the SAS. |
Effect | The CBSD enables SR-OS on the cellular interface. |
Recovery | Not applicable. |
tmnxCellPortCbsdGranted
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2079 |
Event name | tmnxCellPortCbsdGranted |
SNMP notification prefix and OID | TIMETRA-CELLULAR-MIB.tmnxCellularNotifications.8 |
Default severity | minor |
Message format string | CBSD $tmnxPortPortID$ Granted - CBSD Id: $tmnxCellPortCbsdAuthId$, Grant Id: $tmnxCellPortCbsdAuthGrantId$, Grant expire time: $tmnxCellPortCbsdAuthGrantExpTime$, Heartbeat interval: $tmnxCellPortCbsdAuthHeartbeatInt$ seconds |
Cause | The tmnxCellPortCbsdGranted notification is generated when the CBSD has received a grant Id from the SAS. The CBSD is not authorized until after the authorized notification is generated. |
Effect | The CBSD is awaiting authorization from the SAS. |
Recovery | Not applicable. |
tmnxCellPortCbsdRegistered
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2077 |
Event name | tmnxCellPortCbsdRegistered |
SNMP notification prefix and OID | TIMETRA-CELLULAR-MIB.tmnxCellularNotifications.6 |
Default severity | minor |
Message format string | CBSD $tmnxPortPortID$ Registered - CBSD Id: $tmnxCellPortCbsdAuthId$, Server: $tmnxCellPortCbsdAuthCurSasSvrIp$ |
Cause | The tmnxCellPortCbsdRegistered notification is generated when the CBSD successfully registers with the SAS. |
Effect | After this notification is generated the CBSD continues the CBSD authorization procedures. |
Recovery | Not applicable. |
tmnxCellPortCbsdTransDown
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2081 |
Event name | tmnxCellPortCbsdTransDown |
SNMP notification prefix and OID | TIMETRA-CELLULAR-MIB.tmnxCellularNotifications.10 |
Default severity | minor |
Message format string | CBSD $tmnxPortPortID$ transitioned from $tmnxCellCbsdAuthPrevTransState$ to $tmnxCellCbsdAuthNewTransState$ - CBSD Id: $tmnxCellPortCbsdAuthId$, Grant Id: $tmnxCellPortCbsdAuthGrantId$, Reason: $tmnxCellCbsdAuthFailReason$, Response code: $tmnxCellCbsdAuthRespCode$ |
Cause | The tmnxCellPortCbsdTransDown notification is generated when the CBSD is transitioning to a lower state. |
Effect | The CBSD proceeds to complete authorization with the SAS from the state the CBSD has transitioned to. |
Recovery | Not applicable. |
tmnxCellPortCbsdUnregistered
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2078 |
Event name | tmnxCellPortCbsdUnregistered |
SNMP notification prefix and OID | TIMETRA-CELLULAR-MIB.tmnxCellularNotifications.7 |
Default severity | minor |
Message format string | CBSD $tmnxPortPortID$ Unregistered - CBSD Id: $tmnxCellPortCbsdAuthId$, Reason: $tmnxCellCbsdAuthFailReason$, Response code: $tmnxCellCbsdAuthRespCode$ |
Cause |
The tmnxCellPortCbsdUnregistered notification is generated when the CBSD is declared unregistered with the SAS. |
Effect | The CBSD restarts the registration procedures with the SAS. |
Recovery | Not applicable. |
tmnxCellularActiveSimChange
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2070 |
Event name | tmnxCellularActiveSimChange |
SNMP notification prefix and OID | TIMETRA-CELLULAR-MIB.tmnxCellularNotifications.5 |
Default severity | major |
Message format string | Active SIM card switched to SIM $tmnxCellMdaOperActiveSim$ ($tmnxCellMdaSimLastSwitchReason$) |
Cause | The tmnxCellularActiveSimChange notification is generated when the active SIM card on the cellular MDA changes. |
Effect | N/A |
Recovery | N/A |
tmnxCellularBearerCreated
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2065 |
Event name | tmnxCellularBearerCreated |
SNMP notification prefix and OID | TIMETRA-CELLULAR-MIB.tmnxCellularNotifications.1 |
Default severity | warning |
Message format string | Dedicated bearer id $tmnxCellPortBearerId$ created on port $tmnxPortPortID$ |
Cause | The tmnxCellularBearerCreated notification is generated when the network creates a dedicated bearer on a cellular port. |
Effect | N/A |
Recovery | N/A |
tmnxCellularBearerDeleted
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2066 |
Event name | tmnxCellularBearerDeleted |
SNMP notification prefix and OID | TIMETRA-CELLULAR-MIB.tmnxCellularNotifications.2 |
Default severity | warning |
Message format string | Dedicated bearer id $tmnxCellPortBearerId$ deleted on port $tmnxPortPortID$ |
Cause | The tmnxCellularBearerDeleted notification is generated when the network removes a dedicated bearer on a cellular port. |
Effect | N/A |
Recovery | N/A |
tmnxCellularBearerModified
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2067 |
Event name | tmnxCellularBearerModified |
SNMP notification prefix and OID | TIMETRA-CELLULAR-MIB.tmnxCellularNotifications.3 |
Default severity | warning |
Message format string | Bearer id $tmnxCellPortBearerId$ modified on port $tmnxPortPortID$ |
Cause |
The tmnxCellularBearerModified notification is generated when the network modifies a bearer on a cellular port. |
Effect | N/A |
Recovery | N/A |
tmnxCellularNoServiceReset
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2069 |
Event name | tmnxCellularNoServiceReset |
SNMP notification prefix and OID | TIMETRA-CELLULAR-MIB.tmnxCellularNotifications.4 |
Default severity | critical |
Message format string | Could not establish service over the cellular port ( $tmnxCellMdaNoServiceResetReason$). Resetting the system in 60 seconds if this condition persists |
Cause | The tmnxCellularNoServiceReset notification is generated before the system resets because it could not establish service over the cellular interface. |
Effect | The system will reset 60 seconds after this event is generated if it cannot establish service over the cellular interface. |
Recovery | The reset of the system may cause the cellular port to become operational. |
tmnxCellularRssiAlarm
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2085 |
Event name | tmnxCellularRssiAlarm |
SNMP notification prefix and OID | TIMETRA-CELLULAR-MIB.tmnxCellularNotifications.11 |
Default severity | minor |
Message format string | The RSSI level detected by cellular port $tmnxPortNotifyPortId$ has been below the threshold $tmnxCellSimCardRssiThresh$ dBm for the duration of $tmnxCellSimCardRssiAlarmTime$ seconds |
Cause | The tmnxCellularRssiAlarm notification is generated when the cellular port has detected the RSSI (Received Signal Strength Indicator) level fell below the configured minimum threshold tmnxCellSimCardRssiThresh for a duration of time configured by tmnxCellSimCardRssiAlarmTime. |
Effect | N/A. |
Recovery | N/A. |
tmnxCellularRssiAlarmClear
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2086 |
Event name | tmnxCellularRssiAlarmClear |
SNMP notification prefix and OID | TIMETRA-CELLULAR-MIB.tmnxCellularNotifications.12 |
Default severity | cleared |
Message format string | Alarm tmnxCellularRssiAlarm is cleared - The RSSI level detected by cellular port $tmnxPortNotifyPortId$ has been equal to or above the threshold $tmnxCellSimCardRssiThresh$ dBm for the duration of $tmnxCellSimCardRssiAlarmTime$ seconds |
Cause | After the tmnxCellularRssiAlarm is generated, the tmnxCellularRssiAlarmClear notification is generated when the cellular port has detected the RSSI (Received Signal Strength Indicator) level rose to equal or above the configured minimum threshold tmnxCellSimCardRssiThresh for the duration of time configured by tmnxCellSimCardRssiAlarmTime. |
Effect | N/A. |
Recovery | N/A. |
tmnxDS1E1LoopbackStarted
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2019 |
Event name | tmnxDS1E1LoopbackStarted |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.24 |
Default severity | minor |
Message format string | DS1/E1 '$tmnxDS1Loopback$' Loopback Started |
Cause | The tmnxDS1E1LoopbackStarted notification is generated when a loopback is provisioned on a DS1/E1 port. |
Effect | N/A |
Recovery | N/A |
tmnxDS1E1LoopbackStopped
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2020 |
Event name | tmnxDS1E1LoopbackStopped |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.25 |
Default severity | minor |
Message format string | DS1/E1 '$tmnxDS1Loopback$' Loopback Stopped |
Cause | The tmnxDS1E1LoopbackStopped notification is generated when a loopback is removed on a DS1/E1 port. The value of tmnxSonetLoopback specifies the type of loopback that was configured and has now been removed. |
Effect | N/A |
Recovery | N/A |
tmnxDS3E3LoopbackStarted
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2021 |
Event name | tmnxDS3E3LoopbackStarted |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.26 |
Default severity | minor |
Message format string | DS3/E3 '$tmnxDS3ChannelLoopback$' Loopback Started |
Cause | The tmnxDS3E3LoopbackStarted notification is generated when a loopback is provisioned on a DS3/E3 port. |
Effect | N/A |
Recovery | N/A |
tmnxDS3E3LoopbackStopped
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2022 |
Event name | tmnxDS3E3LoopbackStopped |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.27 |
Default severity | minor |
Message format string | DS3/E3 '$tmnxDS3ChannelLoopback$' Loopback Stopped |
Cause | The tmnxDS3E3LoopbackStopped notification is generated when a loopback is removed on a DS3/E3 port. The value of tmnxDS3ChannelLoopback specifies the type of loopback that was configured and has now been removed. |
Effect | N/A |
Recovery | N/A |
tmnxDSXClockSyncStateChange
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2034 |
Event name | tmnxDSXClockSyncStateChange |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.37 |
Default severity | minor |
Message format string | Clock Sync State ( $tmnxDSXClockSyncStateObject$) |
Cause |
Generated when the tmnxDS3ChannelClockSyncState changes for a DS3 or DS1 channel with adaptive or differential clock source. |
Effect | N/A |
Recovery | N/A |
tmnxEqCohOptPortAlarm
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2056 |
Event name | tmnxEqCohOptPortAlarm |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.56 |
Default severity | minor |
Message format string | Coherent Optical Alarms Active: $tmnxCohOptPortAlarmState$ |
Cause |
The tmnxEqCohOptAlarmState notification indicates that a coherent optical port has experienced either a raising or a clearing of an alarm as indicated by the value of tmnxCohOptPortAlarmState. Further details can be obtained from the value of tmnxCohOptPortDefectPoints. |
Effect | N/A |
Recovery | N/A |
tmnxEqDigitalDiagMonitorClear
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2041 |
Event name | tmnxEqDigitalDiagMonitorClear |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.43 |
Default severity | minor |
Message format string | XFP/SFP DDM ( $tmnxDDMFailedObject$) cleared |
Cause |
Generated when an SFP/XFP that supports Digital Diagnostic Monitoring (DDM) clears a failed state. |
Effect | N/A |
Recovery | N/A |
tmnxEqDigitalDiagMonitorFailure
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2030 |
Event name | tmnxEqDigitalDiagMonitorFailure |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.35 |
Default severity | minor |
Message format string | SFF DDM $tmnxDDMLaneIdOrModule$ ( $tmnxDDMFailedObject$) raised |
Cause |
Generated when an SFF that supports Digital Diagnostic Monitoring (DDM) enters a failed state. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortBndlBadEndPtDiscr
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2012 |
Event name | tmnxEqPortBndlBadEndPtDiscr |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.21 |
Default severity | minor |
Message format string | Port $tmnxPortPortId$ detected inconsistent peer endpoint discriminator for the bundle |
Cause | Generated when the port detected mismatched peer endpoint discriminator for the bundle. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortBndlRedDiffExceeded
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2011 |
Event name | tmnxEqPortBndlRedDiffExceeded |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.20 |
Default severity | major |
Message format string | Port $tmnxPortNotifyPortId$ exceeded red differential delay of $tmnxBundleRedDiffDelay$ |
Cause |
Generated when the differential delay of a port in the bundle exceeds the configured value in tmnxBundleRedDiffDelay. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortBndlYellowDiffExceeded
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2010 |
Event name | tmnxEqPortBndlYellowDiffExceeded |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.19 |
Default severity | minor |
Message format string | Port $tmnxPortNotifyPortId$ exceeded yellow differential delay of $tmnxBundleYellowDiffDelay$ |
Cause |
Generated when the differential delay of a port in the bundle exceeds the configured value in tmnxBundleYellowDiffDelay. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortDS1Alarm
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2015 |
Event name | tmnxEqPortDS1Alarm |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.17 |
Default severity | minor |
Message format string | Alarm $tmnxPortNotifyDS1AlarmReason$ Set |
Cause | Generated when a DS1 interface alarm condition is detected. It is generated only when the type of alarm being raised is enabled in tmnxDS1ReportAlarm. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortDS1AlarmClear
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2016 |
Event name | tmnxEqPortDS1AlarmClear |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.18 |
Default severity | minor |
Message format string | Alarm $tmnxPortNotifyDS1AlarmReason$ Cleared |
Cause | Generated when a DS1 interface alarm condition is cleared. It is generated only when the type of alarm being cleared is enabled in tmnxDS1ReportAlarm. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortDS3Alarm
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2013 |
Event name | tmnxEqPortDS3Alarm |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.15 |
Default severity | minor |
Message format string | Alarm $tmnxPortNotifyDS3AlarmReason$ Set |
Cause | Generated when a DS3 interface alarm condition is detected. It is generated only when the type of alarm being raised is enabled in tmnxDS3ChannelReportAlarm. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortDS3AlarmClear
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2014 |
Event name | tmnxEqPortDS3AlarmClear |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.16 |
Default severity | minor |
Message format string | Alarm $tmnxPortNotifyDS3AlarmReason$ Cleared |
Cause | Generated when a DS3 interface alarm condition is cleared. It is generated only when the type of alarm being cleared is enabled in tmnxDS3ChannelReportAlarm. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortDuplexCfgNotCompatible
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2028 |
Event name | tmnxEqPortDuplexCfgNotCompatible |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.33 |
Default severity | major |
Message format string | Provisioned duplex $tmnxPortEtherDuplex$ not compatible with MDA type $tmnxMdaNotifyTyp$ |
Cause | Generated when a supported MDA is inserted into a slot of an IOM, the MDA is compatible with the currently provisioned MDA, but the currently configured duplex on an MDA port is not compatible with the inserted MDA. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortError
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2009 |
Event name | tmnxEqPortError |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.14 |
Default severity | minor |
Message format string | Physical port $tmnxPortNotifyError$ |
Cause |
Generated when an error listed in tmnxPortNotifyError is detected on the port. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortEtherAlarm
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2017 |
Event name | tmnxEqPortEtherAlarm |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.22 |
Default severity | minor |
Message format string | Alarm $tmnxPortNotifyEtherAlarmReason$ Set |
Cause | tmnxEqPortEtherAlarm is generated when a ethernet port alarm condition is detected. It is generated only when the type of alarm being raised is enabled in tmnxPortEtherReportAlarm. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortEtherAlarmClear
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2018 |
Event name | tmnxEqPortEtherAlarmClear |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.23 |
Default severity | minor |
Message format string | Alarm $tmnxPortNotifyEtherAlarmReason$ Cleared |
Cause | tmnxEqPortEtherAlarmClear is generated when a ethernet port alarm condition is cleared. It is generated only when the type of alarm being cleared is enabled in tmnxPortEtherReportAlarm. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortEtherCrcAlarm
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2052 |
Event name | tmnxEqPortEtherCrcAlarm |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.52 |
Default severity | minor |
Message format string | CRC errors in excess of the configured $tmnxPortNotifyEtherCrcAlarmValue$ threshold $tmnxPortNotifyEtherCrcMultiplier$*10e- $tmnxPortNotifyEtherCrcThreshold$ Set |
Cause | tmnxEqPortEtherCrcAlarm is generated when an Ethernet port CRC alarm condition is detected. It is generated only when the type of alarm being raised is enabled on the port. |
Effect | On a signal failure (SF) fault, the port is taken out of service until the CRC alarm condition is cleared. |
Recovery | tmnxEqPortEtherCrcAlarm is cleared by taking the port out of service (eg. shutdown, card/mda reset, physical link loss), or changing/disabling the associated threshold/multiplier values. Signal Degradation is self- clearing and will clear once the error rate drops below 1/10th of the configured rate. |
tmnxEqPortEtherCrcAlarmClear
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2053 |
Event name | tmnxEqPortEtherCrcAlarmClear |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.53 |
Default severity | minor |
Message format string | CRC errors in excess of the configured $tmnxPortNotifyEtherCrcAlarmValue$ threshold $tmnxPortNotifyEtherCrcMultiplier$*10e- $tmnxPortNotifyEtherCrcThreshold$ Cleared |
Cause | tmnxEqPortEtherCrcAlarmClear is generated when an Ethernet port CRC alarm condition is cleared or disabled. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortEtherEgressRateChange
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2068 |
Event name | tmnxEqPortEtherEgressRateChange |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.62 |
Default severity | minor |
Message format string | Port $tmnxNotifyPortId$ oper egress rate has changed to $tmnxPortEtherOperEgressRate$ kbps |
Cause | The tmnxEqPortEtherEgressRateChange notification is generated when the port's operational egress rate changes, due to the reception of ETH-BN (Ethernet Bandwidth Notification) messages, or from a configuration change. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortEtherInternalAlarm
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2054 |
Event name | tmnxEqPortEtherInternalAlarm |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.54 |
Default severity | minor |
Message format string | Excess internal MAC TX errors detected Set |
Cause | tmnxEqPortEtherInternalAlarm is generated when an Ethernet port experiences excessive internal MAC tx errors. It is generated only when tmnxPortEtherDownOnInternalError is enabled on the port. |
Effect | A port experiencing excessive internal MAC tx errors will take the port out of service while the alarm condition is in effect. |
Recovery | tmnxEqPortEtherInternalAlarm is cleared by taking the port out of service (eg. shutdown, card/mda reset, physical link loss), or setting tmnxPortEtherDownOnInternalError to the value 'false'. |
tmnxEqPortEtherInternalAlarmClr
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2055 |
Event name | tmnxEqPortEtherInternalAlarmClr |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.55 |
Default severity | minor |
Message format string | Excess internal MAC TX errors detected Cleared |
Cause | tmnxEqPortEtherInternalAlarmClr is generated when an Ethernet port no longer experiences excessive internal MAC tx errors. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortEtherLoopCleared
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2026 |
Event name | tmnxEqPortEtherLoopCleared |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.31 |
Default severity | minor |
Message format string | Ethernet loop cleared on $tmnxPortNotifyPortId$ |
Cause |
The tmnxEqPortEtherLoopCleared notification is generated when down-when-looped detects an Ethernet port has stopped receiving PDUs that it transmitted and tmnxPortEtherDownWhenLoopedEnabled is set to 'true'. Setting tmnxPortEtherDownWhenLoopedEnabled to 'false' will also cause this notification to be generated if tmnxEqPortEtherLoopDetected had previously been raised. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortEtherLoopDetected
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2025 |
Event name | tmnxEqPortEtherLoopDetected |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.30 |
Default severity | minor |
Message format string | Ethernet loop detected on $tmnxPortNotifyPortId$ |
Cause |
The tmnxEqPortEtherLoopDetected notification is generated when down-when-looped detects an Ethernet port is receiving PDUs that it transmitted and tmnxPortEtherDownWhenLoopedEnabled is set to 'true'. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortEtherSymMonAlarm
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2057 |
Event name | tmnxEqPortEtherSymMonAlarm |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.57 |
Default severity | minor |
Message format string | Symbol errors in excess of the configured $tmnxPortNotifyEtherSymAlarmValue$ threshold $tmnxPortNotifyEtherSymMultiplier$*10e- $tmnxPortNotifyEtherSymThreshold$ Set |
Cause | tmnxEqPortEtherSymMonAlarm is generated when an Ethernet port Symbol alarm condition is detected. It is generated only when the type of alarm being raised is enabled on the port. |
Effect | On a signal failure (SF) fault, the port is taken out of service until the Symbol alarm condition is cleared. |
Recovery | tmnxEqPortEtherSymMonAlarm is cleared by taking the port out of service (eg. shutdown, card/mda reset, physical link loss), or changing/disabling the associated threshold/multiplier values. Signal Degradation is self- clearing and will clear once the error rate drops below 1/10th of the configured rate. |
tmnxEqPortEtherSymMonAlarmClear
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2058 |
Event name | tmnxEqPortEtherSymMonAlarmClear |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.58 |
Default severity | minor |
Message format string | Symbol errors in excess of the configured $tmnxPortNotifyEtherSymAlarmValue$ threshold $tmnxPortNotifyEtherSymMultiplier$*10e- $tmnxPortNotifyEtherSymThreshold$ Cleared |
Cause | tmnxEqPortEtherSymMonAlarmClear is generated when an Ethernet port Symbol alarm condition is cleared or disabled. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortIngressRateCfgNotCompatible
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2029 |
Event name | tmnxEqPortIngressRateCfgNotCompatible |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.34 |
Default severity | major |
Message format string | Ingress rate provisioning not supported on MDA type $tmnxMdaNotifyType$ |
Cause |
Generated when a supported MDA is inserted into a slot of an IOM, the MDA is compatible with the currently provisioned MDA, but the currently configured ingress rate on an MDA port is not compatible with the inserted MDA. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortSFPInserted
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2005 |
Event name | tmnxEqPortSFPInserted |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.8 |
Default severity | minor |
Message format string | SFF Inserted |
Cause | Generated when a SFP is inserted in the port. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortSFPRemoved
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2006 |
Event name | tmnxEqPortSFPRemoved |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.9 |
Default severity | minor |
Message format string | SFF Removed |
Cause | Generated when a SFP is removed from the port. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortSonetAlarm
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2001 |
Event name | tmnxEqPortSonetAlarm |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.4 |
Default severity | minor |
Message format string | Alarm $tmnxPortNotifySonetAlarmReason$ Set |
Cause | Generated when a SONET/SDH port alarm condition is detected. It is generated only when the type of alarm being raised is enabled in tmnxSonetReportAlarm. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortSonetAlarmClear
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2002 |
Event name | tmnxEqPortSonetAlarmClear |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.5 |
Default severity | minor |
Message format string | Alarm $tmnxPortNotifySonetAlarmReason$ Cleared |
Cause | Generated when a SONET/SDH port alarm condition is cleared. It is generated only when the type of alarm being cleared is enabled in tmnxSonetReportAlarm. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortSonetPathAlarm
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2003 |
Event name | tmnxEqPortSonetPathAlarm |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.6 |
Default severity | minor |
Message format string | Alarm $tmnxPortNotifySonetPathAlarmReason$ Set |
Cause | Generated when a SONET/SDH path alarm condition is detected. It is generated only when the type of alarm being raised is enabled in tmnxSonetPathReportAlarm. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortSonetPathAlarmClear
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2004 |
Event name | tmnxEqPortSonetPathAlarmClear |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.7 |
Default severity | minor |
Message format string | Alarm $tmnxPortNotifySonetPathAlarmReason$ Cleared |
Cause | Generated when a SONET/SDH path alarm condition is cleared. It is generated only when the type of alarm being cleared is enabled in tmnxSonetPathReportAlarm. |
Effect | N/A |
Recovery | N/A |
tmnxEqPortSpeedCfgNotCompatible
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2027 |
Event name | tmnxEqPortSpeedCfgNotCompatible |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.32 |
Default severity | major |
Message format string | Provisioned speed $tmnxPortEtherSpeed$ not compatible with MDA type $tmnxMdaNotifyType$ |
Cause | Generated when a supported MDA is inserted into a slot of an IOM, the MDA is compatible with the currently provisioned MDA, but the currently configured speed on an MDA port is not compatible with the inserted MDA. |
Effect | N/A |
Recovery | N/A |
tmnxEqSonetClockSrcNotCompatible
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2046 |
Event name | tmnxEqSonetClockSrcNotCompatible |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.46 |
Default severity | major |
Message format string | Configured SONET/SDH clock source $tmnxSonetClockSource$ not compatible with MDA type $tmnxMdaNotifyType$ |
Cause | Notification tmnxEqSonetClockSrcNotCompatible is generated when a supported MDA is inserted into a slot of an IOM, the MDA is compatible with the currently provisioned MDA, but the currently configured SONET/SDH clock source on an MDA port is not compatible with the inserted MDA. |
Effect | Though services can still be created, the MDA will fail to operate as configured and will be in a failed state. |
Recovery | Change the configuration to reflect the capabilities of the MDA port, or switch out the MDA for one that is compatible. |
tmnxEqSonetFramingNotCompatible
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2048 |
Event name | tmnxEqSonetFramingNotCompatible |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.48 |
Default severity | major |
Message format string | Configured SONET/SDH framing $tmnxSonetFraming$ not compatible with MDA type $tmnxMdaNotifyType$ |
Cause | Notification tmnxEqSonetFramingNotCompatible is generated when a supported MDA is inserted into a slot of an IOM, the MDA is compatible with the currently provisioned MDA, but the currently configured SONET/SDH framing on an MDA port is not compatible with the inserted MDA. |
Effect | Though services can still be created, the MDA will fail to operate as configured and will be in a failed state. |
Recovery | Change the configuration to reflect the capabilities of the MDA port, or switch out the MDA for one that is compatible. |
tmnxEqSonetSfThreshNotCompatible
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2047 |
Event name | tmnxEqSonetSfThreshNotCompatible |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.47 |
Default severity | major |
Message format string | Configured SONET/SDH SF threshold 10e- $tmnxSonetBerSfThreshold$ not compatible with MDA type $tmnxMdaNotifyType$ |
Cause | Notification tmnxEqSonetSfThreshNotCompatible is generated when a supported MDA is inserted into a slot of an IOM, the MDA is compatible with the currently provisioned MDA, but the currently configured SONET/SDH Signal Fail (SF) threshold on an MDA port is not compatible with the inserted MDA. |
Effect | Though services can still be created, the MDA will fail to operate as configured and will be in a failed state. |
Recovery | Change the configuration to reflect the capabilities of the MDA port, or switch out the MDA for one that is compatible. |
tmnxHwAggShpSchedOperColorAmber
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2083 |
Event name | tmnxHwAggShpSchedOperColorAmber |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.68 |
Default severity | minor |
Message format string | Hw-agg-shaper-scheduler Amber Alarm |
Cause | The notification tmnxHwAggShpSchedOperColorAmber is generated when the number of hw-agg-shapers for an object (Vport) hw-agg-shaper-scheduler policy has crossed 90% of scaling threshold. |
Effect | Hw Agg shaper scheduler algorithm will stop running. |
Recovery | Monitor the hw-agg-shappers closely within the hw-agg-shapper-scheduler policy. |
tmnxHwAggShpSchedOperColorGreen
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2082 |
Event name | tmnxHwAggShpSchedOperColorGreen |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.67 |
Default severity | minor |
Message format string | Hw-agg-shaper-scheduler Green Alarm |
Cause | The notification tmnxHwAggShpSchedOperColorGreen is generated when the number of hw-agg-shapers for an object (Vport) hw-agg-shaper-scheduler policy is well within thresholds. |
Effect | Hw Agg shaper scheduler algorithm is running within the normal parameters. |
Recovery | None required. |
tmnxHwAggShpSchedOperColorRed
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2084 |
Event name | tmnxHwAggShpSchedOperColorRed |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.69 |
Default severity | minor |
Message format string | Hw-agg-shaper-scheduler Red Alarm |
Cause | The notification tmnxHwAggShpSchedOperColorRed is generated when the number of hw-agg-shapers for an object (Vport) hw-agg-shaper-scheduler policy has crossed 100% of scaling threshold. |
Effect | Hw Agg shaper scheduler algorithm has stopped running. |
Recovery | Reduce the hw-agg-shapers attached to the hw-agg-shapper-scheduler policy. |
tmnxOtuIfAlarmNotification
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2037 |
Event name | tmnxOtuIfAlarmNotification |
SNMP notification prefix and OID | TIMETRA-OTU-MIB.tmnxOtuNotifications.1 |
Default severity | minor |
Message format string | OTU Alarms Set $tmnxOtuIfAlarmState$ |
Cause |
The tmnxOtuIfAlarmNotification notification indicates that an OTU interface has experienced either a raising or clearing of an alarm in the Forward Error Correction (FEC), Section Monitoring (SM), Path Monitoring (PM) or Payload Monitoring (PSI) fields of the OTU frame. |
Effect | N/A |
Recovery | N/A |
tmnxPortAUIReset
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2076 |
Event name | tmnxPortAUIReset |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.66 |
Default severity | warning |
Message format string | Reset of the attachment unit interface - likely cause $tmnxPortNotifyAUIResetSource$ |
Cause |
This log event is used only for connectorized ports where a CAUI reset is not expected. This may indicate an issue with the optical line feeding into the SFF that is passed through to the system. |
Effect | A reset of the AUI will impact all connector-ports on the connector. Generally, AUI resets are recovered immediately but there can be impact to the traffic flow. |
Recovery | As this is reporting an unexpected condition related to the external optical line, the line and the SFF should be investigated. |
tmnxPortEtherLoopbackStarted
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2071 |
Event name | tmnxPortEtherLoopbackStarted |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.63 |
Default severity | major |
Message format string | Started '$tmnxPortEtherLoopback$' loopback on Ethernet port $tmnxPortPortID$ |
Cause |
The tmnxPortEtherLoopbackStarted notification is generated when tmnxPortEtherLoopback is modified to set the Ethernet port to a loopback mode. |
Effect | Setting the port in loopback mode impacts the normal flow of traffic across the port. |
Recovery | Remove loopback on the port to restore normal traffic flow. |
tmnxPortEtherLoopbackStopped
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2072 |
Event name | tmnxPortEtherLoopbackStopped |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.64 |
Default severity | major |
Message format string | Stopped '$tmnxPortEtherLoopback$' loopback on Ethernet port $tmnxPortPortID$ |
Cause |
The tmnxPortEtherLoopbackStopped notification is generated when a loopback is removed on an Ethernet port. The value of tmnxPortEtherLoopback specifies the type of loopback that was configured and has now been removed. |
Effect | The loopback has been removed and normal traffic flow may resume. |
Recovery | No recovery is required. |
tmnxPortGnssStatusChange
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2073 |
Event name | tmnxPortGnssStatusChange |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.65 |
Default severity | major |
Message format string | GNSS port $tmnxPortPortID$ status changed; sync $tmnxPortGnssSyncStatus$, antenna: $tmnxPortGnssAntennaStatus$, receiver: $tmnxPortGnssReceiverStatus$ |
Cause |
This notification may be triggered for a variety of reasons including (but not limited to): 1) The antenna is experiencing fault issues 2) The number of visible satellites is too low |
Effect | The GNSS receiver is not able to provide a sync-worthy clock signal. |
Recovery | If the customer is expecting the GNSS receiver to be locked, the customer will need to determine the root cause (for example, insufficient visible satellites) and resolve the issue (for example, ensure tmnxPortGnssElevationMaskAngle is set accordingly) |
tmnxPortUnsupportedFunction
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2036 |
Event name | tmnxPortUnsupportedFunction |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.38 |
Default severity | warning |
Message format string | A functionality is required from port $tmnxPortNotifyPortId$ that it cannot support - $tmnxPortNotifyDescription$ |
Cause | Generated when a functionality is required from this port that it cannot support. The object tmnxPortNotifyDescription explains what function is affected. |
Effect | N/A |
Recovery | N/A |
tmnxResvCbsPoolThreshAmber
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2050 |
Event name | tmnxResvCbsPoolThreshAmber |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.50 |
Default severity | minor |
Message format string | Amber Alarm: CBS over Amber threshold: ObjType= $tmnxObjType$ Owner=$tmnxObjPortId$ Type=$tmnxObjAppType$ Pool= $tmnxObjAppPool$ ResvSize=$tmnxObjAppResvSize$ SumOfQ ResvSize= $tmnxObjAppSumOfQResvSize$ Old ResvCBS=$tmnxObjAppResvCbsOld$ New ResvCBS= $tmnxObjAppResvCbsNew$ Old ResvSize=$tmnxObjAppResvSizeOld$ |
Cause | The notification tmnxResvCbsPoolThreshAmber is generated when a reserved-CBS of an object (MDA or port) has crossed threshold value specified by tmnxObjectAppAmbrAlrmThresh. |
Effect | This is warning event but the traffic is not yet affected. |
Recovery | The value of tmnxObjectAppResvCbs may need to be adjusted. |
tmnxResvCbsPoolThreshGreen
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2049 |
Event name | tmnxResvCbsPoolThreshGreen |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.49 |
Default severity | minor |
Message format string | Green Alarm: CBS within threshold: ObjType= $tmnxObjType$ Owner=$tmnxObjPortId$ Type=$tmnxObjAppType$ Pool= $tmnxObjAppPool$ ResvSize=$tmnxObjAppResvSize$ SumOfQ ResvSize= $tmnxObjAppSumOfQResvSize$ Old ResvCBS=$tmnxObjAppResvCbsOld$ New ResvCBS= $tmnxObjAppResvCbsNew$ Old ResvSize=$tmnxObjAppResvSizeOld$ |
Cause | Notification tmnxResvCbsPoolThreshGreen is generated when a reserved- CBS of an object (MDA or port) returns to within defined thresholds. |
Effect | Reserved CBS of the object has returned to within normal parameters. |
Recovery | None required. |
tmnxResvCbsPoolThreshRed
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2051 |
Event name | tmnxResvCbsPoolThreshRed |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.51 |
Default severity | major |
Message format string | Red Alarm: CBS over Red threshold: ObjType= $tmnxObjType$ Owner=$tmnxObjPortId$ Type=$tmnxObjAppType$ Pool= $tmnxObjAppPool$ ResvSize=$tmnxObjAppResvSize$ SumOfQ ResvSize= $tmnxObjAppSumOfQResvSize$ Old ResvCBS=$tmnxObjAppResvCbsOld$ New ResvCBS= $tmnxObjAppResvCbsNew$ Old ResvSize=$tmnxObjAppResvSizeOld$ |
Cause | The notification tmnxResvCbsPoolThreshRed is generated when a reserved-CBS of an object (MDA or port) has crossed the threshold value specified by tmnxObjectAppRedAlrmThresh. |
Effect | This is a critical event and the traffic may be affected. |
Recovery | The value of tmnxObjectAppResvCbs may need to be adjusted. |
tmnxRS232ControlLeadSignalChg
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2062 |
Event name | tmnxRS232ControlLeadSignalChg |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.59 |
Default severity | minor |
Message format string | Serial port $tmnxPortNotifyPortId$ control leads signal change: $tmnxPortNotifyLeadsSignalChg$ |
Cause |
This notification may be triggered for a variety of reasons. One example is that the far-end equipment has been disconnected. |
Effect | Alert user of transitions. |
Recovery | Determine root cause and resolve accordingly. |
tmnxRS232SquelchResetIssued
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2064 |
Event name | tmnxRS232SquelchResetIssued |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.61 |
Default severity | minor |
Message format string | Serial port $tmnxPortNotifyPortId$ squelch reset issued, existing squelch status: $tmnxRS232SocketSquelchStatus$ |
Cause |
N/A |
Effect |
N/A |
Recovery | N/A |
tmnxRS232SquelchStatusChange
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2063 |
Event name | tmnxRS232SquelchStatusChange |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.60 |
Default severity | minor |
Message format string | Serial port $tmnxPortNotifyPortId$ squelch status: $tmnxRS232SocketSquelchStatus$ |
Cause |
This notification may be triggered for the following reasons: 1) A continuous stream of data is being received for a specified period of time, tmnxRS232SocketSquelchDelay. 2) The continuous stream of data is no longer being received for a specified period of time, tmnxRS232SocketUnsquelchDelay. |
Effect | Incoming data will be suppressed or unsuppressed accordingly. |
Recovery | Determine root cause of far-end sending continuous data and resolve accordingly. |
tmnxSonetSDHLoopbackStarted
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2023 |
Event name | tmnxSonetSDHLoopbackStarted |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.28 |
Default severity | minor |
Message format string | Sonet/SDH '$tmnxSonetLoopback$' Loopback Started |
Cause | The tmnxSonetSDHLoopbackStarted notification is generated when a loopback is provisioned on a Sonet-SDH port. |
Effect | N/A |
Recovery | N/A |
tmnxSonetSDHLoopbackStopped
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2024 |
Event name | tmnxSonetSDHLoopbackStopped |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.29 |
Default severity | minor |
Message format string | Sonet/SDH '$tmnxSonetLoopback$' Loopback Stopped |
Cause | The tmnxSonetSDHLoopbackStopped notification is generated when a loopback test is removed on a Sonet-SDH port. The value of tmnxDS1Loopback specifies the type of loopback that was configured and has now been removed. |
Effect | N/A |
Recovery | N/A |
tmnxWlanNetworkConnected
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2074 |
Event name | tmnxWlanNetworkConnected |
SNMP notification prefix and OID | TIMETRA-WLAN-MIB.tmnxWlanNotifications.1 |
Default severity | minor |
Message format string | Connected to WLAN network $tmnxWlanNotifyWlanNetworkId$ SSID '$tmnxWlanNetworkSSID$' |
Cause | The system generates a tmnxWlanNetworkConnected notification when the system establishes a WLAN connection to the specified network. |
Effect | N/A |
Recovery | N/A |
tmnxWlanNetworkDisconnected
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2075 |
Event name | tmnxWlanNetworkDisconnected |
SNMP notification prefix and OID | TIMETRA-WLAN-MIB.tmnxWlanNotifications.2 |
Default severity | minor |
Message format string | Disconnected from WLAN network $tmnxWlanNotifyWlanNetworkId$ SSID '$tmnxWlanNetworkSSID$' |
Cause | The system generates a tmnxWlanNetworkDisconnected notification when the system loses the WLAN connection to the specified network. |
Effect | N/A |
Recovery | N/A |
tPortAccEgrQGrpHostMatchFailure
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2039 |
Event name | tPortAccEgrQGrpHostMatchFailure |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.41 |
Default severity | major |
Message format string | Could not find a specific port egress queue-group for host with inter-dest-id ' $tmnxHostMatchNotifyIntDestId$', org-string '$tmnxHostMatchNotifyOrgString$' and sub-id ' $tmnxHostMatchNotifySubIdent$' on port $tmnxPortNotifyPortId$. The default 'policer-output-queues' queue-group will be used. |
Cause | The tPortAccEgrQGrpHostMatchFailure notification indicates that a host match lookup failed to resolve a specific port egress queue-group. In such case the default policer-output-queue is used. |
Effect | N/A |
Recovery | N/A |
tPortEgrVPortHostMatchFailure
Property name | Value |
---|---|
Application name | PORT |
Event ID | 2040 |
Event name | tPortEgrVPortHostMatchFailure |
SNMP notification prefix and OID | TIMETRA-PORT-MIB.tmnxPortNotification.42 |
Default severity | major |
Message format string | Could not find a specific port egress virtual port for host with inter-dest-id ' $tmnxHostMatchNotifyIntDestId$', org-string '$tmnxHostMatchNotifyOrgString$' and sub-id ' $tmnxHostMatchNotifySubIdent$' on port $tmnxPortNotifyPortId$ |
Cause | The tPortEgrVPortHostMatchFailure notification indicates that a host match lookup failed to resolve a specific port egress virtual port. |
Effect | N/A |
Recovery | N/A |