Workflow to manage shelf objects

Purpose

The following workflow describes the sequence of high-level tasks required to manage and configure shelf objects and shelf object children. This workflow assumes that the physical devices have been installed, commissioned, and discovered. See Chapter 8, Device commissioning and management for more information about device commissioning. See Chapter 9, Device discovery for more information about device discovery.

Note: Shelf objects and shelf object children can be accessed using the equipment navigation tree. See Chapter 3, NFM-P navigation tree for more information about using the equipment navigation tree.

Stages
 

As required, perform the following procedures to configure shelf objects.

  1. Configure the chassis mode of a device. See To configure the device chassis mode .

  2. Configure a VWM shelf for a 7210 SAS device. See To configure a VWM shelf for a 7210 SAS .

  3. Configure dry contact sensor monitoring. See To configure dry contact sensors .

  4. Configure the IMM card type on a 7210 SAS-R. See To configure the IMM card type on a 7210 SAS-R .

  5. Configure switch fabric multicast ingress replication rates. See To configure switch fabric multicast ingress replication rates .

  6. Configure IMPM overrides. See To configure IMPM overrides .

  7. Enable mixed mode on a 7450 ESS or 7750 SR device. See To enable mixed mode .

  8. Configure an IEEE 1588 PTP port on a 7705 SAR. See To configure an IEEE 1588 PTP port on a 7705 SAR .

  9. Configure system time on a 7705 SAR. See To configure system time on a 7705 SAR .

  10. Configure SNTP on a 7705 SAR. See To configure SNTP on a 7705 SAR .

  11. Configure NTP on supported device types. See To configure NTP on supported devices .

  12. Configure the IEEE 1588 PTP clock on supported devices. See To configure the IEEE 1588 PTP clock on a 7210 SAS, 7250 IXR, 7450 ESS, or 7750 SR.

  13. Configure the IEEE 1588 PTP peer on supported devices. See To configure the IEEE 1588 PTP peer of a 7210 SAS, 7250 IXR, 7450 ESS, or 7750 SR.

  14. Configure the IEEE 1588 PTP port on supported devices. See To configure IEEE 1588 PTP ports on a 7210 SAS, 7250 IXR, 7450 ESS, 7750 SR, or 7950 XRS.

  15. Manage OmniSwitch running configuration. See To manage an OmniSwitch running configuration .

  16. Configure OmniSwitch health monitoring. See To configure OmniSwitch health monitoring .

  17. Configure a CCM on a 7950 XRS-20. See To configure a CCM on a 7950 XRS-20 .

  18. Configure power supply trays. See To configure a power supply tray .

  19. Configure power management zones. See To configure a power management zoneTo provision an APEQ , and To configure a variable power supply APEQ .


Assign a card type to a chassis slot. See To assign a card type .


As required, configure the card and card slot objects as follows:

  1. Configure an egress WRED queue control on an IOM 3 or IMM forwarding plane. See To configure egress WRED queue control on an XCM, IOM 3 or IMM forwarding plane .

  2. Configure IMPM on a 2 × XP MDA IOM 3 or IMM forwarding plane. See To configure IMPM on an XCM, 2 x XP MDA IOM 3, or IMM forwarding plane .

  3. Enable named pool mode. See To enable named pool mode .

  4. Configure OmniSwitch stacks. See To configure OmniSwitch stacks .

  5. Configure an OmniSwitch CPU temperature threshold. See To configure an OmniSwitch CPU temperature threshold .

  6. Configure a CPM on a 7950 XRS. See To configure a CPM .


As required, configure daughter card objects as follows:

  1. Configure an MDA. See To configure an MDA .

  2. Configure IMPM on an MDA. See To configure IMPM on an MDA .

  3. Specify an event action for a 7x50 MDA. See To specify an event action for a 7x50 MDA .

  4. View operational multicast channel properties on an MDA. See To view the operational multicast channel properties of an MDA .

  5. Configure a module card on the 7705 SAR-M/ME. See To configure a module card on a 7705 SAR-M/ME or 7705 SAR-H .


As required, configure shelf objects that require daughter cards as follows:

  1. Configure timing synchronization. See To configure timing synchronization .

  2. Configure an IEEE 1588 clock on a 7705 SAR. See To configure an IEEE 1588 PTP clock on a 7705 SAR .

  3. Configure SCADA on a 7705 SAR. See To configure SCADA on a 7705 SAR .

  4. Configure a 7705 SAR microwave link. See To configure a 7705 SAR MW link .

  5. Configure a 7705 SAR MW link member. See To configure a 7705 SAR MW link member .

  6. Configure auxiliary alarm definitions on a 7705 SAR. See To configure 7705 SAR auxiliary alarm definitions .


As required, create or modify bundle objects as follows:

  1. FR group bundle. See To create an FR group bundle and To modify an FR group bundle .

  2. IMA group bundle. See To create an IMA group bundle and To modify an IMA group bundle .

  3. MLPPP bundle. See To create an MLPPP bundle and To modify an MLPPP bundle .

  4. MLPPP bundle for multiclass service transmission. See To configure an MLPPP bundle for multiclass service transmission .

  5. MLPPP bundle as a network interface on a channelized ASAP MDA. See To configure an MLPPP bundle as a network interface on a channelized ASAP MDA .