Chapter 11: Ethernet/Data network provisioning procedures

Overview

Purpose

This chapter includes procedures necessary to provision Ethernet and Data features in Alcatel-Lucent 1665 DMX.

Contents

Before you begin

Procedure 11-1: Establishing Ethernet services

Procedure 11-2: Establish point-to-point UPSR protected 1GbE full rate private line service (NOTAG mode)

Procedure 11-3: Establish point-to-point UPSR protected GbE service (802.1q mode)

Procedure 11-4: Establish point-to-point UPSR protected GbE service (transparent mode)

Procedure 11-5: Establish Ethernet packet ring on a UPSR

Procedure 11-6: Establish 802.1q mode Ethernet service on established packet ring (UPSR)

Procedure 11-7: Establish transparent mode Ethernet service on established packet ring (UPSR)

Procedure 11-8: Establish Ethernet packet ring on a BLSR without NUT

Procedure 11-9: Establish 802.1q mode Ethernet service on established packet ring (BLSR protected)

Procedure 11-10: Establish transparent mode Ethernet service on established packet ring (BLSR protected)

Procedure 11-11: Provision Ethernet LAN port parameters

Procedure 11-12: Provision Ethernet VCG parameters

Procedure 11-13: Provision Ethernet circuit pack parameters

Procedure 11-14: Establish point-to-point BLSR protected 1GbE full rate private line service (NOTAG mode)

Procedure 11-15: Establish point-to-point BLSR protected GbE service (802.1q mode)

Procedure 11-16: Establish point-to-point BLSR protected GbE service (transparent mode)

Procedure 11-17: Establish Ethernet packet ring on a BLSR with non-preemptible unprotected traffic (NUT)

Procedure 11-18: Add bandwidth to a point-to-point UPSR/BLSR protected GbE service (802.1q mode)

Procedure 11-19: Establish a dedicated multiple point private line UPSR protected GbE service (transparent mode)

Procedure 11-20: Add Fast Ethernet services to Ethernet packet ring – FE to GbE hairpin

Procedure 11-21: Establish LNW71 10/100-PL Fast Ethernet private line service on UPSR

Procedure 11-22: Establish video broadcast network on UPSR

Procedure 11-23: Establish video broadcast network on BLSR

Procedure 11-24: Make cross-connections for Ethernet service

Cross-Connections for Ethernet

Procedure 11-25: Create preferred spanning tree configuration

Procedure 11-26: Change an existing spanning tree configuration

Procedure 11-27: Create/Delete/Lock MAC address on a port

Procedure 11-28: Provision Q in Q stacked VLAN capability

Procedure 11-29: Perform Ethernet loopback transmission test

Procedure 11-30: Enable/Disable LAN port transmission

Procedure 11-31: Provision Ethernet quality of service (QoS) - LNW70/LNW170

Procedure 11-32: Provision Ethernet QoS parameters

Procedure 11-33: Provision LCAS, add/enable/remove tributaries

Procedure 11-34: Establish LNW74 10/100-T/F enhanced Fast Ethernet private line service on UPSR

Procedure 11-35: Establish LNW73/LNW73C FC-DPORT SAN transport service on UPSR

Procedure 11-36: Provision LNW73/LNW73C FC-DPORT circuit pack parameters

Procedure 11-37: Provision FC-DPORT DATA port parameters

Procedure 11-38: Provision FC-DPORT VCG parameters

Procedure 11-39: Make cross-connections for LNW73/LNW73C FC-DPORT SAN transport service

Procedure 11-40: Establish video multi-channel broadcast network on UPSR/BLSR (NOTAG mode)

Procedure 11-41: Provision Resilient Packet Ring (RPR)-capable VCG parameters

Procedure 11-42: Provision Resilient Packet Ring (RPR)-specific VCG parameters

Procedure 11-43: Bridge and roll Ethernet cross-connections

Procedure 11-44: Establish Resilient Packet Ring (RPR)

Procedure 11-45: Provision Ethernet quality of service (QoS) - LNW78

Procedure 11-46: Create/Modify/Delete link aggregation group (LAG)

Procedure 11-47: Enable/Disable transmission audit

Procedure 11-48: Provision Ethernet ring protection (ERP)