Install SYSCTL circuit pack.

Reference:

Procedure 4-1: Install SYSCTL (LNW2) in new Alcatel-Lucent 1665 DMXtend shelf

Connect personal computer and establish WaveStar^® CIT session.

Reference:

Procedure 14-2: Connect Personal Computer (PC) and establish WaveStar^® CIT session

Install system software, if required.

Reference:

• Procedure 2-1: Install software generic (initial) via FTAM or

• Procedure 2-2: Install software generic (initial) via FTP

Install high-speed OLIU circuit packs in the Main slots.

Reference:

Procedure 4-2: Install OLIU circuit packs in Main slots

Provision high-speed OLIU ports, if required at this time and not already performed.

Reference:

Procedure 4-4: Provision OLIU circuit packs/ports for service

Install any required low-speed OLIU circuit packs in Function Unit D or G slots.

Reference:

Procedure 4-3: Install OLIU circuit packs in Function slots

Provision low-speed OLIU ports, if required at this time and not already performed in the previous step.

Reference:

Procedure 4-4: Provision OLIU circuit packs/ports for service

Important!

The system Timing Mode should be provisioned to Free Running or External to avoid Holdover alarms before the end-to-end system is established. The Timing Mode may be re-provisioned when the end-to-end system is established.

If this system is going to be line timed or externally timed and the timing reference is not yet available, select Configuration → Timing/Sync to provision the system Timing Mode to Free Running, or External if the external timing references are available.

Reference:

Procedure 6-5: Network Element synchronization provisioning

Important!

If the Main slots are equipped with LNW84 OC3/OC12/OC48, LNW140 OC-3/DS1, or LNW141 OC-192 circuit packs, the LNW39 and LNW391 DS1/DS3/16/3 combination circuit packs are not supported.

Install any required DS1/DS3/16/3 circuit packs.

Reference:

Procedure 4-6: Install DS1/DS3/16/3 circuit packs

Provision DS1/DS3/16/3 ports, if required at this time and not already performed.

The LNW39 and LNW391 DS1/DS3/16/3 circuit packs do not support EC-1 and E1 interfaces.

Reference:

• Procedure 4-8: Provision DS3/EC1 circuit packs/ports for service

• Procedure 4-10: Provision DS1/E1 circuit packs/ports for service

Important!

If the Main slots are equipped with Very Large Fabric LNW84 or LNW141 OLIU circuit packs, the LNW6 and LNW7 DS1 circuit packs are not supported. If the Main slots are equipped with LNW84, LNW140, or LNW141 circuit packs, LNW112 DS1 circuit packs are not supported.

Install any required DS1/E1 circuit packs.

Reference:

Procedure 4-9: Install DS1/E1 circuit packs

Provision DS1/E1 ports, if required at this time and not already performed.

The LNW6, LNW7 and LNW112 DS1 circuit packs do not support E1 interfaces.

Reference:

Procedure 4-10: Provision DS1/E1 circuit packs/ports for service

Important!

If the Main slots are equipped with LNW84, LNW140 or LNW141 OLIU circuit packs, LNW111 DS3/3 circuit packs are not supported.

Install any required DS3/EC1 circuit packs.

Reference:

Procedure 4-7: Install DS3/EC1 circuit packs

Provision DS3/EC-1 ports, if required at this time and not already performed.

The LNW111 DS3 circuit pack does not support EC-1 interfaces.

Reference:

Procedure 4-8: Provision DS3/EC1 circuit packs/ports for service

Install any required TMUX circuit packs.

Reference:

Procedure 4-11: Install TMUX circuit packs

Provision TMUX ports, if required at this time and not already performed.

Reference:

Procedure 4-12: Provision TMUX circuit packs/ports for service

Install any required Ethernet circuit packs.

Reference:

• Procedure 4-13: Install 10/100 Ethernet circuit packs

• Procedure 4-14: Install Gigabit Ethernet circuit packs

Provision Ethernet circuit packs/ports/VCGs, if required at this time and not already performed.

Reference:

Procedure 4-15: Provision Ethernet circuit packs/LAN port/VCG for service

Install any required Fibre Channel circuit packs.

Reference:

Procedure 4-17: Install Fibre Channel circuit packs

Provision Fibre Channel circuit packs/data ports/VCGs, if required at this time and not already performed.

Reference:

Procedure 4-18: Provision Fibre Channel circuit pack/Data port/VCG for service

NOTICE Service-disruption hazard

Improperly-seated circuit packs or missing apparatus blanks may cause service hits on in-service systems.

All slots in Alcatel-Lucent 1665 DMXtend must be equipped with fully-seated circuit packs or apparatus blanks to prevent service hits on in-service systems.

Install 177D Apparatus Blanks or LNW98 Detectable Apparatus Blanks in any unused slot in Group D1/D2 or G1/G2. Install LNW43 Apparatus Blanks or LNW96 Detectable Apparatus Blanks in any unused slot in Group A1/B1 or A2/B2. Install LNW42 Apparatus Blanks or LNW95 Detectable Apparatus Blanks in an unused Main 2 slot.

Important!

All slots in the Alcatel-Lucent 1665 DMXtend must be equipped with fully-seated circuit packs or apparatus blanks.

Important!

A deeper shelf cover (comcode 849064282) is required for shelves equipped with LNW55 OC3/OC12/OC48, LNW84 OC3/OC12/OC48, LNW705 XM10G/8, and/or LNW785 OMD circuit packs. This shelf cover provides more space to prevent fibers from touching the front cover when the cover is closed.

If required, verify that the shelf is equipped with the deeper shelf cover.

Perform the LED test to verify that all LEDs are operating properly.

Reference:

Procedure 14-13: Perform LED test

Perform local terminal transmission tests, if required.

Reference:

• Procedure 14-9: Perform DS1/E1 transmission test

• Procedure 14-10: Perform DS3 transmission test

• Procedure 14-11: Perform EC-1 transmission test

Perform local facility transmission tests, if required.

Reference:

• Procedure 14-9: Perform DS1/E1 transmission test

• Procedure 14-10: Perform DS3 transmission test

• Procedure 14-11: Perform EC-1 transmission test

Test protection switching function, if required.

Reference:

Procedure 14-12: Test function unit equipment protection switching

Check office alarm interface by local procedure, if required.

Perform one of the following depending on whether or not you have already provisioned circuit packs and ports for service:

• Circuit packs and/or ports were provisioned in this procedure:

  Perform the following to delete any cross-connections, loopbacks, or protection switches that may have been made during testing:

  1. Select View → Cross-Connections from the System View menu. Select Shelf from the View Cross Connections window, then click Select. Print or save the cross-connections to be deleted, then click Close. Select Configuration → Cross-Connections from the System View window to start the Cross Connection Wizard. Follow the instruction in the Wizard to delete the necessary cross-connections.

  2. Select View → Loopback from the System View menu. Select Shelf from the View Loopbacks window, then click Select. Print or save the existing loopbacks to be released, then click Close.

     Select Fault → Analysis → Loopback from the System View menu. Expand the details in the Loopback window, select the port with the loopback to be released, then click Select. Select Release and the Loopback Type, then click Apply at the bottom of the Loopback window. Click Yes to the Warning message to release the loopback. Click Close to exit.

  3. Select View → Protection from the System View menu. Select the required protection group, then click Select. Note the Protection Switch State. Repeat for each protection group, then click Close.

     If required, select Fault → Protection Switch from the System View menu to access the required protection group and clear any protection switches. Click Apply and click Yes. If required, repeat for each protection group, then click Close.

• Circuit packs and/or ports were not provisioned in this procedure:

  The following command resets all system provisionable parameters and cross-connections to factory default values. If you have already set provisionable parameters for the installed circuit packs/ports, they will be reset to factory default values.

  From the System View menu, select Fault → Reset → Initialize System to reset system parameters to default values, if required. Read all the warnings and follow the prompts to execute the command.

Result:

You will be logged off the system during the controller reset and provisionable parameters will be set to factory default.

A flashing b in the IND display on the SYSCTL indicates that a boot is in progress. During the boot, the b may extinguish for up to 20 seconds and then resume flashing.

Holdover alarm may also occur since timing mode reverts back to External. If required to silence the alarm, select Configuration → Timing/Sync and provision the system timing mode to Free Running.

If the sockets on LNW55 and LNW84 multirate OLIU circuit packs are equipped with pluggable transmission modules, the system reports unexpected or failed Pluggable Transmission Module alarms. If desired, select Configuration → Equipment to access the affected ports and provision the port Signal Type parameter the required rate that matches the pluggable transmission module.

Set/Change system TID (NE name), as required.

Important!

The TID is a case-insensitive character string from 1 to 20 characters and must be unique for each NE in the network.

Reference:

Procedure 7-11: Set/change system TID

Provision optional system parameters as required from work order or office records.

Reference:

• Chapter 6, System configuration procedures

• Chapter 7, System administration procedures

• Chapter 8, System performance monitoring procedures

• Appendix A, Provisionable parameters

Establish the Alcatel-Lucent 1665 DMXtend subnetwork, when required.

Reference:

Chapter 9, Network configuration procedures

End of steps